| Age | Commit message (Collapse) | Author |
|---|
|
product
STMicroelectronics i2c tpm is the only one to have a different tristate
label.
Rename it "TPM Interface Specification 1.2 Interface (I2C - STMicroelectronics)"
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
[phuewe: corrected module name in the helptext]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
When sending data in tpm_stm_i2c_send, each loop iteration send buf.
Send buf + i instead as the goal of this for loop is to send a number
of byte from buf that fit in burstcnt. Once those byte are sent, we are
supposed to send the next ones.
The driver was working because the burstcount value returns always the maximum size for a TPM
command or response. (0x800 for a command and 0x400 for a response).
Cc: stable@vger.kernel.org
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
"tpm_dev_vendor_release"
The tpm_dev_vendor_release() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
sizeof(u8) is always 1.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.
vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values. Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.
We added a NULL check. In addition, a default buffer size will
be set when NULL is returned.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do
not send IRQs while also having an ACPI TPM entry indicating that they
will be sent. These machines freeze on resume while the tpm_tis module
waits for an IRQ, eventually timing out.
When in interrupt mode, the tpm_tis module should receive an IRQ during
module init. Fall back to polling mode if none is received when expected.
Cc: <stable@vger.kernel.org>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor checkpatch fixed]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Currently these driver are missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds a missing check for tpm_i2c_atmel.c and tpm_i2c_nuvoton.c
Cc: stable@vger.kernel.org
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Add newly registered TPMs to the tail of the list, not the beginning, so that
things that are specifying TPM_ANY_NUM don't find that the device they're
using has inadvertently changed. Adding a second device would break IMA, for
instance.
Cc: stable@vger.kernel.org
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Instead of looping by ourselves we may use %*phN specifier to dump a small
buffer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ PHuewe: removed now unused variable i ]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Some Atmel TPMs provide completely wrong timeouts from their
TPM_CAP_PROP_TIS_TIMEOUT query. This patch detects that and returns
new correct values via a DID/VID table in the TIS driver.
Tested on ARM using an AT97SC3204T FW version 37.16
Cc: <stable@vger.kernel.org>
[PHuewe: without this fix these 'broken' Atmel TPMs won't function on
older kernels]
Signed-off-by: "Berg, Christopher" <Christopher.Berg@atmel.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Regression in 41ab999c. Call to tpm_chip_put is missing. This
will cause TPM device driver not to unload if tmp_get_random()
is called.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Properly clean the sysfs entries in the error path
Cc: <stable@vger.kernel.org>
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Most device drivers do call 'tpm_do_selftest' which executes a
TPM_ContinueSelfTest. tpm_i2c_stm_st33 is just pointlessly different,
I think it is bug.
These days we have the general assumption that the TPM is usable by
the kernel immediately after the driver is finished, so we can no
longer defer the mandatory self test to userspace.
Cc: <stable@vger.kernel.org> # 3.12+
Reported-by: Richard Marciel <rmaciel@linux.vnet.ibm.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
* acpica: (63 commits)
ACPICA: Namespace: Remove _PRP method support.
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPICA: acpidump: Fix repetitive table dump in -n mode.
ACPI: Clean up acpi_os_map/unmap_memory() to eliminate __iomem.
ACPICA: Clean up redudant definitions already defined elsewhere
ACPICA: Linux headers: Add <asm/acenv.h> to remove mis-ordered inclusion of <asm/acpi.h>
ACPICA: Linux headers: Add <acpi/platform/aclinuxex.h>
ACPICA: Linux headers: Remove ACPI_PREEMPTION_POINT() due to no usages.
ACPICA: Update version to 20140424.
ACPICA: Comment/format update, no functional change.
ACPICA: Events: Update GPE handling and initialization code.
ACPICA: Remove extraneous error message for large number of GPEs.
ACPICA: Tables: Remove old mechanism to validate if XSDT contains NULL entries.
ACPICA: Tables: Add new mechanism to skip NULL entries in RSDT and XSDT.
ACPICA: acpidump: Add support to force using RSDT.
ACPICA: Back port of improvements on exception code.
ACPICA: Back port of _PRP update.
ACPICA: acpidump: Fix truncated RSDP signature validation.
ACPICA: Linux header: Add support for stubbed externals.
...
|
|
ACPICA doesn't include protections around address space checking, Linux
build tests always complain increased sparse warnings around ACPICA
internal acpi_os_map/unmap_memory() invocations. This patch tries to fix
this issue permanently.
There are 2 choices left for us to solve this issue:
1. Add __iomem address space awareness into ACPICA.
2. Remove sparse checker of __iomem from ACPICA source code.
This patch chooses solution 2, because:
1. Most of the acpi_os_map/unmap_memory() invocations are used for ACPICA.
table mappings, which in fact are not IO addresses.
2. The only IO addresses usage is for "system memory space" mapping code in:
drivers/acpi/acpica/exregion.c
drivers/acpi/acpica/evrgnini.c
drivers/acpi/acpica/exregion.c
The mapped address is accessed in the handler of "system memory space"
- acpi_ex_system_memory_space_handler(). This function in fact can be
changed to invoke acpi_os_read/write_memory() so that __iomem can
always be type-casted in the OSL layer.
According to the above investigation, we drew the following conclusion:
It is not a good idea to introduce __iomem address space awareness into
ACPICA mostly in order to protect non-IO addresses.
We can simply remove __iomem for acpi_os_map/unmap_memory() to remove
__iomem checker for ACPICA code. Then we need to enforce external usages
to invoke other APIs that are aware of __iomem address space.
The external usages are:
drivers/acpi/apei/einj.c
drivers/acpi/acpi_extlog.c
drivers/char/tpm/tpm_acpi.c
drivers/acpi/nvs.c
This patch thus performs cleanups in this way:
1. Add acpi_os_map/unmap_iomem() to be invoked by non-ACPICA code.
2. Remove __iomem from acpi_os_map/unmap_memory().
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Chromebooks (at least Acer C720 and Pixel) implement an ACPI object
for TPM, but don't implement the _DSM method to support PPI. As
a result, the TPM driver fails to load on those machines after
commit 1569a4c4ceba (ACPI / TPM: detect PPI features by checking
availability of _DSM functions) which causes them to fail to
resume from system suspend, becuase they require the TPM hardware
to be put into the right state during resume and the TPM driver
is necessary for that.
Fix the problem by making tpm_add_ppi() return 0 when tpm_ppi_handle
is still NULL after walking the ACPI namespace in search for the PPI
_DSM, which allows the TPM driver to load and operate the hardware
(during system resume in particular), but avoid creating the PPI
sysfs group in that case.
This change is based on a prototype patch from Jiang Liu.
Fixes: 1569a4c4ceba (ACPI / TPM: detect PPI features by checking availability of _DSM functions)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74021
Reported-by: James Duley <jagduley@gmail.com>
Reported-by: Phillip Dixon <phil@dixon.gen.nz>
Tested-by: Brandon Casey <drafnel@gmail.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally. So
HAS_IOPORT_MAP is the better name for this.
Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.
The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available. I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.
The changes in this commit were done using:
$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Airlie <airlied@linux.ie>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Ashley Lai <ashley@ashleylai.com>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"Two major features that Xen community is excited about:
The first is event channel scalability by David Vrabel - we switch
over from an two-level per-cpu bitmap of events (IRQs) - to an FIFO
queue with priorities. This lets us be able to handle more events,
have lower latency, and better scalability. Good stuff.
The other is PVH by Mukesh Rathor. In short, PV is a mode where the
kernel lets the hypervisor program page-tables, segments, etc. With
EPT/NPT capabilities in current processors, the overhead of doing this
in an HVM (Hardware Virtual Machine) container is much lower than the
hypervisor doing it for us.
In short we let a PV guest run without doing page-table, segment,
syscall, etc updates through the hypervisor - instead it is all done
within the guest container. It is a "hybrid" PV - hence the 'PVH'
name - a PV guest within an HVM container.
The major benefits are less code to deal with - for example we only
use one function from the the pv_mmu_ops (which has 39 function
calls); faster performance for syscall (no context switches into the
hypervisor); less traps on various operations; etc.
It is still being baked - the ABI is not yet set in stone. But it is
pretty awesome and we are excited about it.
Lastly, there are some changes to ARM code - you should get a simple
conflict which has been resolved in #linux-next.
In short, this pull has awesome features.
Features:
- FIFO event channels. Key advantages: support for over 100,000
events (2^17), 16 different event priorities, improved fairness in
event latency through the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with
paravirtualized disk and network, paravirtualized interrupts and
timers, no emulated devices of any kind (and thus no qemu), no BIOS
or legacy boot — but instead of requiring PV MMU, it uses the HVM
hardware extensions to virtualize the pagetables, as well as system
calls and other privileged operations." (from "The
Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels"
* tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (52 commits)
xen/pvh: Set X86_CR0_WP and others in CR0 (v2)
MAINTAINERS: add git repository for Xen
xen/pvh: Use 'depend' instead of 'select'.
xen: delete new instances of __cpuinit usage
xen/fb: allow xenfb initialization for hvm guests
xen/evtchn_fifo: fix error return code in evtchn_fifo_setup()
xen-platform: fix error return code in platform_pci_init()
xen/pvh: remove duplicated include from enlighten.c
xen/pvh: Fix compile issues with xen_pvh_domain()
xen: Use dev_is_pci() to check whether it is pci device
xen/grant-table: Force to use v1 of grants.
xen/pvh: Support ParaVirtualized Hardware extensions (v3).
xen/pvh: Piggyback on PVHVM XenBus.
xen/pvh: Piggyback on PVHVM for grant driver (v4)
xen/grant: Implement an grant frame array struct (v3).
xen/grant-table: Refactor gnttab_init
xen/grants: Remove gnttab_max_grant_frames dependency on gnttab_init.
xen/pvh: Piggyback on PVHVM for event channels (v2)
xen/pvh: Update E820 to work with PVH (v2)
xen/pvh: Secondary VCPU bringup (non-bootup CPUs)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security layer updates from James Morris:
"Changes for this kernel include maintenance updates for Smack, SELinux
(and several networking fixes), IMA and TPM"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (39 commits)
SELinux: Fix memory leak upon loading policy
tpm/tpm-sysfs: active_show() can be static
tpm: tpm_tis: Fix compile problems with CONFIG_PM_SLEEP/CONFIG_PNP
tpm: Make tpm-dev allocate a per-file structure
tpm: Use the ops structure instead of a copy in tpm_vendor_specific
tpm: Create a tpm_class_ops structure and use it in the drivers
tpm: Pull all driver sysfs code into tpm-sysfs.c
tpm: Move sysfs functions from tpm-interface to tpm-sysfs
tpm: Pull everything related to /dev/tpmX into tpm-dev.c
char: tpm: nuvoton: remove unused variable
tpm: MAINTAINERS: Cleanup TPM Maintainers file
tpm/tpm_i2c_atmel: fix coccinelle warnings
tpm/tpm_ibmvtpm: fix unreachable code warning (smatch warning)
tpm/tpm_i2c_stm_st33: Check return code of get_burstcount
tpm/tpm_ppi: Check return value of acpi_get_name
tpm/tpm_ppi: Do not compare strcmp(a,b) == -1
ima: remove unneeded size_limit argument from ima_eventdigest_init_common()
ima: update IMA-templates.txt documentation
ima: pass HASH_ALGO__LAST as hash algo in ima_eventdigest_init()
ima: change the default hash algorithm to SHA1 in ima_eventdigest_ng_init()
...
|
|
* acpi-dsm:
ACPI / extlog: replace open-coded _DSM code with helper functions
ACPI / nouveau: replace open-coded _DSM code with helper functions
nouveau / ACPI: fix memory leak in ACPI _DSM related code
ACPI / i915: replace open-coded _DSM code with helper functions
ACPI / i2c-hid: replace open-coded _DSM code with helper functions
ACPI / TPM: detect PPI features by checking availability of _DSM functions
ACPI / TPM: replace open-coded _DSM code with helper functions
ACPI / TPM: match node name instead of full path when searching for TPM device
PCI / pci-label: treat PCI label with index 0 as valid label
ACPI / PCI: replace open-coded _DSM code with helper functions
PCI / pci-label: release allocated ACPI object on error recovery path
ACPI: introduce helper interfaces for _DSM method
|
|
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
|
|
so we make it static
CC: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
CC: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
If CONFIG_PM_SLEEP=n, CONFIG_PNP=y we get this warning:
drivers/char/tpm/tpm_tis.c:706:13: warning: 'tpm_tis_reenable_interrupts' defined but not used [-Wunused-function]
This seems to have been introduced in a2fa3fb0d 'tpm: convert tpm_tis driver
to use dev_pm_ops from legacy pm_ops'
Also, unpon reviewing, the #ifdefs around tpm_tis_pm are not right, the first
reference is protected, the second is not. tpm_tis_pm is always defined so we
can drop the #ifdef.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This consolidates everything that is only used within tpm-dev.c
into tpm-dev.c and out of the publicly visible struct tpm_chip.
The per-file allocation lays the ground work for someday fixing the
strange forced O_EXCL behaviour of the current code.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This builds on the last commit to use the ops structure in the core
and reduce the size of tpm_vendor_specific.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This replaces the static initialization of a tpm_vendor_specific
structure in the drivers with the standard Linux idiom of providing
a const structure of function pointers.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe: did apply manually due to commit
191ffc6bde3 tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
The tpm core now sets up and controls all sysfs attributes, instead
of having each driver have a unique take on it.
All drivers now now have a uniform set of attributes, and no sysfs
related entry points are exported from the tpm core module.
This also uses the new method used to declare sysfs attributes
with DEVICE_ATTR_RO and 'struct attribute *'
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: had to apply the tpm_i2c_atmel part manually due to commit
191ffc6bde3fc tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
CLASS-sysfs.c is a common idiom for linux subsystems.
This is the first step to pulling all the sysfs support code from
the drivers into tpm-sysfs. This is a plain text copy from tpm-interface
with support changes to make it compile.
_tpm_pcr_read is made non-static and is called tpm_pcr_read_dev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
CLASS-dev.c is a common idiom for Linux subsystems
This pulls all the code related to the miscdev into tpm-dev.c and makes it
static. The identical file_operation structs in the drivers are purged and the
tpm common code unconditionally creates the miscdev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe:
tpm_dev_release is now used only in this file, thus the EXPORT_SYMBOL
can be dropped and the function be marked as static.
It has no other in-kernel users]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
“wait” wait queue is defined but never used in the function, thus
it can be removed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
drivers/char/tpm/tpm_i2c_atmel.c:178:8-9: WARNING: return of 0/1 in function 'i2c_atmel_req_canceled' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: coccinelle/misc/boolreturn.cocci
CC: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
CC: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
smatch complains:
drivers/char/tpm/tpm_ibmvtpm.c:510
ibmvtpm_crq_process() info: ignoring unreachable code.
-> The return is not necessary here, remove it
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
The 'get_burstcount' function can in some circumstances 'return -EBUSY' which
in tpm_stm_i2c_send is stored in an 'u32 burstcnt'
thus converting the signed value into an unsigned value, resulting
in 'burstcnt' being huge.
Changing the type to u32 only does not solve the problem as the signed
value is converted to an unsigned in I2C_WRITE_DATA, resulting in the
same effect.
Thus
-> Change type of burstcnt to u32 (the return type of get_burstcount)
-> Add a check for the return value of 'get_burstcount' and propagate a
potential error.
This makes also sense in the 'I2C_READ_DATA' case, where the there is no
signed/unsigned conversion.
found by coverity
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
If
status = acpi_get_name(handle, ACPI_FULL_PATHNAME, &buffer);
fails for whatever reason and does not return AE_OK
if (strstr(buffer.pointer, context) != NULL) {
does dereference a null pointer.
-> Check the return value and return the status to the caller
Found by coverity
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Depending on the implementation strcmp might return the difference between
two strings not only -1,0,1 consequently
if (strcmp (a,b) == -1)
might lead to taking the wrong branch
-> compare with < 0 instead,
which in any case is more canonical.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Detecting physical presence interface features by checking availbility
of corresponding ACPI _DSM functions, it should be more accurate than
checking TPM version number.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use helper functions to simplify _DSM related code in TPM driver.
This patch also help to get rid of following warning messages:
[ 163.509575] ACPI Error: Incorrect return type [Buffer] requested [Package]
(20130517/nsxfeval-135)
But there is still an warning left.
[ 181.637366] ACPI Warning: \_SB_.IIO0.LPC0.TPM_._DSM: Argument #4 type
mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When searching ACPI object for TPM device, it should match current
ACPI object name instead of the full path.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In function ppi_callback(), memory allocated by acpi_get_name() will get
leaked when current device isn't the desired TPM device, so fix the
memory leak.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The user has the option of disabling the platform driver:
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device (rev 01)
which is used to unplug the emulated drivers (IDE, Realtek 8169, etc)
and allow the PV drivers to take over. If the user wishes
to disable that they can set:
xen_platform_pci=0
(in the guest config file)
or
xen_emul_unplug=never
(on the Linux command line)
except it does not work properly. The PV drivers still try to
load and since the Xen platform driver is not run - and it
has not initialized the grant tables, most of the PV drivers
stumble upon:
input: Xen Virtual Keyboard as /devices/virtual/input/input5
input: Xen Virtual Pointer as /devices/virtual/input/input6M
------------[ cut here ]------------
kernel BUG at /home/konrad/ssd/konrad/linux/drivers/xen/grant-table.c:1206!
invalid opcode: 0000 [#1] SMP
Modules linked in: xen_kbdfront(+) xenfs xen_privcmd
CPU: 6 PID: 1389 Comm: modprobe Not tainted 3.13.0-rc1upstream-00021-ga6c892b-dirty #1
Hardware name: Xen HVM domU, BIOS 4.4-unstable 11/26/2013
RIP: 0010:[<ffffffff813ddc40>] [<ffffffff813ddc40>] get_free_entries+0x2e0/0x300
Call Trace:
[<ffffffff8150d9a3>] ? evdev_connect+0x1e3/0x240
[<ffffffff813ddd0e>] gnttab_grant_foreign_access+0x2e/0x70
[<ffffffffa0010081>] xenkbd_connect_backend+0x41/0x290 [xen_kbdfront]
[<ffffffffa0010a12>] xenkbd_probe+0x2f2/0x324 [xen_kbdfront]
[<ffffffff813e5757>] xenbus_dev_probe+0x77/0x130
[<ffffffff813e7217>] xenbus_frontend_dev_probe+0x47/0x50
[<ffffffff8145e9a9>] driver_probe_device+0x89/0x230
[<ffffffff8145ebeb>] __driver_attach+0x9b/0xa0
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145cf1c>] bus_for_each_dev+0x8c/0xb0
[<ffffffff8145e7d9>] driver_attach+0x19/0x20
[<ffffffff8145e260>] bus_add_driver+0x1a0/0x220
[<ffffffff8145f1ff>] driver_register+0x5f/0xf0
[<ffffffff813e55c5>] xenbus_register_driver_common+0x15/0x20
[<ffffffff813e76b3>] xenbus_register_frontend+0x23/0x40
[<ffffffffa0015000>] ? 0xffffffffa0014fff
[<ffffffffa001502b>] xenkbd_init+0x2b/0x1000 [xen_kbdfront]
[<ffffffff81002049>] do_one_initcall+0x49/0x170
.. snip..
which is hardly nice. This patch fixes this by having each
PV driver check for:
- if running in PV, then it is fine to execute (as that is their
native environment).
- if running in HVM, check if user wanted 'xen_emul_unplug=never',
in which case bail out and don't load any PV drivers.
- if running in HVM, and if PCI device 5853:0001 (xen_platform_pci)
does not exist, then bail out and not load PV drivers.
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=ide-disks',
then bail out for all PV devices _except_ the block one.
Ditto for the network one ('nics').
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=unnecessary'
then load block PV driver, and also setup the legacy IDE paths.
In (v3) make it actually load PV drivers.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Reported-and-Tested-by: Fabio Fantoni <fabio.fantoni@m2r.biz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Add extra logic to handle the myrid ways 'xen_emul_unplug'
can be used per Ian and Stefano suggestion]
[v3: Make the unnecessary case work properly]
[v4: s/disks/ide-disks/ spotted by Fabio]
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [for PCI parts]
CC: stable@vger.kernel.org
|
|
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"In this patchset, we finally get an SELinux update, with Paul Moore
taking over as maintainer of that code.
Also a significant update for the Keys subsystem, as well as
maintenance updates to Smack, IMA, TPM, and Apparmor"
and since I wanted to know more about the updates to key handling,
here's the explanation from David Howells on that:
"Okay. There are a number of separate bits. I'll go over the big bits
and the odd important other bit, most of the smaller bits are just
fixes and cleanups. If you want the small bits accounting for, I can
do that too.
(1) Keyring capacity expansion.
KEYS: Consolidate the concept of an 'index key' for key access
KEYS: Introduce a search context structure
KEYS: Search for auth-key by name rather than target key ID
Add a generic associative array implementation.
KEYS: Expand the capacity of a keyring
Several of the patches are providing an expansion of the capacity of a
keyring. Currently, the maximum size of a keyring payload is one page.
Subtract a small header and then divide up into pointers, that only gives
you ~500 pointers on an x86_64 box. However, since the NFS idmapper uses
a keyring to store ID mapping data, that has proven to be insufficient to
the cause.
Whatever data structure I use to handle the keyring payload, it can only
store pointers to keys, not the keys themselves because several keyrings
may point to a single key. This precludes inserting, say, and rb_node
struct into the key struct for this purpose.
I could make an rbtree of records such that each record has an rb_node
and a key pointer, but that would use four words of space per key stored
in the keyring. It would, however, be able to use much existing code.
I selected instead a non-rebalancing radix-tree type approach as that
could have a better space-used/key-pointer ratio. I could have used the
radix tree implementation that we already have and insert keys into it by
their serial numbers, but that means any sort of search must iterate over
the whole radix tree. Further, its nodes are a bit on the capacious side
for what I want - especially given that key serial numbers are randomly
allocated, thus leaving a lot of empty space in the tree.
So what I have is an associative array that internally is a radix-tree
with 16 pointers per node where the index key is constructed from the key
type pointer and the key description. This means that an exact lookup by
type+description is very fast as this tells us how to navigate directly to
the target key.
I made the data structure general in lib/assoc_array.c as far as it is
concerned, its index key is just a sequence of bits that leads to a
pointer. It's possible that someone else will be able to make use of it
also. FS-Cache might, for example.
(2) Mark keys as 'trusted' and keyrings as 'trusted only'.
KEYS: verify a certificate is signed by a 'trusted' key
KEYS: Make the system 'trusted' keyring viewable by userspace
KEYS: Add a 'trusted' flag and a 'trusted only' flag
KEYS: Separate the kernel signature checking keyring from module signing
These patches allow keys carrying asymmetric public keys to be marked as
being 'trusted' and allow keyrings to be marked as only permitting the
addition or linkage of trusted keys.
Keys loaded from hardware during kernel boot or compiled into the kernel
during build are marked as being trusted automatically. New keys can be
loaded at runtime with add_key(). They are checked against the system
keyring contents and if their signatures can be validated with keys that
are already marked trusted, then they are marked trusted also and can
thus be added into the master keyring.
Patches from Mimi Zohar make this usable with the IMA keyrings also.
(3) Remove the date checks on the key used to validate a module signature.
X.509: Remove certificate date checks
It's not reasonable to reject a signature just because the key that it was
generated with is no longer valid datewise - especially if the kernel
hasn't yet managed to set the system clock when the first module is
loaded - so just remove those checks.
(4) Make it simpler to deal with additional X.509 being loaded into the kernel.
KEYS: Load *.x509 files into kernel keyring
KEYS: Have make canonicalise the paths of the X.509 certs better to deduplicate
The builder of the kernel now just places files with the extension ".x509"
into the kernel source or build trees and they're concatenated by the
kernel build and stuffed into the appropriate section.
(5) Add support for userspace kerberos to use keyrings.
KEYS: Add per-user_namespace registers for persistent per-UID kerberos caches
KEYS: Implement a big key type that can save to tmpfs
Fedora went to, by default, storing kerberos tickets and tokens in tmpfs.
We looked at storing it in keyrings instead as that confers certain
advantages such as tickets being automatically deleted after a certain
amount of time and the ability for the kernel to get at these tokens more
easily.
To make this work, two things were needed:
(a) A way for the tickets to persist beyond the lifetime of all a user's
sessions so that cron-driven processes can still use them.
The problem is that a user's session keyrings are deleted when the
session that spawned them logs out and the user's user keyring is
deleted when the UID is deleted (typically when the last log out
happens), so neither of these places is suitable.
I've added a system keyring into which a 'persistent' keyring is
created for each UID on request. Each time a user requests their
persistent keyring, the expiry time on it is set anew. If the user
doesn't ask for it for, say, three days, the keyring is automatically
expired and garbage collected using the existing gc. All the kerberos
tokens it held are then also gc'd.
(b) A key type that can hold really big tickets (up to 1MB in size).
The problem is that Active Directory can return huge tickets with lots
of auxiliary data attached. We don't, however, want to eat up huge
tracts of unswappable kernel space for this, so if the ticket is
greater than a certain size, we create a swappable shmem file and dump
the contents in there and just live with the fact we then have an
inode and a dentry overhead. If the ticket is smaller than that, we
slap it in a kmalloc()'d buffer"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (121 commits)
KEYS: Fix keyring content gc scanner
KEYS: Fix error handling in big_key instantiation
KEYS: Fix UID check in keyctl_get_persistent()
KEYS: The RSA public key algorithm needs to select MPILIB
ima: define '_ima' as a builtin 'trusted' keyring
ima: extend the measurement list to include the file signature
kernel/system_certificate.S: use real contents instead of macro GLOBAL()
KEYS: fix error return code in big_key_instantiate()
KEYS: Fix keyring quota misaccounting on key replacement and unlink
KEYS: Fix a race between negating a key and reading the error set
KEYS: Make BIG_KEYS boolean
apparmor: remove the "task" arg from may_change_ptraced_domain()
apparmor: remove parent task info from audit logging
apparmor: remove tsk field from the apparmor_audit_struct
apparmor: fix capability to not use the current task, during reporting
Smack: Ptrace access check mode
ima: provide hash algo info in the xattr
ima: enable support for larger default filedata hash algorithms
ima: define kernel parameter 'ima_template=' to change configured default
ima: add Kconfig default measurement list template
...
|
|
just like the other entries
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This patch changes the displayed module name from
tpm_tis_i2c_infineon to its actual name tpm_i2c_infineon.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This is based on the work of Teddy Reed <teddy@prosauce.org> published
on GitHub:
https://github.com/theopolis/tpm-i2c-atmel.git
34894b988b67e0ae55088d6388e77b0dbf10c07d
That driver was never merged, I have taken it as a starting port,
forward ported, tested and revised the driver:
- Make it broadly textually similar to the Infineon and Nuvoton I2C
driver
- Place everything in a format suitable for mainline inclusion
- Use high level I2C functions i2c_master_send and
i2c_master_recv for data xfer
- Use the timeout system from the core code, by faking out a status
register
- Only I2C transfer the number of bytes in the reply, not a fixed
message size.
- checkpatch cleanups
- Testing on ARM Kirkwood, with this device tree, using a
AT97SC3204T-X1A180
tpm@29 {
compatible = "atmel,at97sc3204t";
reg = <0x29>;
};
Signed-off-by: Teddy Reed <teddy@prosauce.org>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This chip is/was also branded as a Winbond WPCT301.
Originally written by Dan Morav <dmorav@nuvoton.com> and posted to LKML:
https://lkml.org/lkml/2011/9/7/206
The original posting was not merged, I have taken it as a
starting point, forward ported, tested and revised the driver:
- Rework interrupt handling to work properly with level triggered
interrupts. The old version just locked up.
- Synchronize various items with Peter Huewe's Infineon driver:
* Add durations/timeouts sysfs calls
* Remove I2C device auto-detection
* Don't fiddle with chip->release
* Call tpm_dev_vendor_release in the probe error path
* Use MODULE_DEVICE_TABLE for the I2C ids
* Provide OF compatible strings for DT support
* Use SIMPLE_DEV_PM_OPS
* Use module_i2c_driver
- checkpatch cleanups
- Testing on ARM Kirkwood with GPIO interrupts, with this device tree:
tpm@57 {
compatible = "nuvoton,npct501";
reg = <0x57>;
interrupt-parent = <&gpio1>;
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
};
Signed-off-by: Dan Morav <dmorav@nuvoton.com>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes, fixed module name in kconfig]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
