| Age | Commit message (Collapse) | Author |
|---|
|
At least the Armada XP SoC supports 4GB on a single DRAM window. Because
the size register values contain the actual size - 1, the MSB is set in
that case. For example, the SDRAM window's control register's value is
0xffffffe1 for 4GB (bits 31 to 24 contain the size).
The MBUS driver reads back each window's size from registers and
calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which
overflows for 32 bit values, resulting in other miscalculations further
on (a bad RAM window for the CESA crypto engine calculated by
mvebu_mbus_setup_cpu_target_nooverlap() in my case).
This patch changes the type in 'struct mbus_dram_window' from u32 to
u64, which allows us to keep using the same register calculation code in
most MBUS-using drivers (which calculate ->size - 1 again).
Fixes: fddddb52a6c4 ("bus: introduce an Marvell EBU MBus driver")
CC: stable@vger.kernel.org
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver
subsystems"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
soc/tegra: fuse: Add missing semi-colon
soc/tegra: Restrict SoC device registration to Tegra
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
soc/tegra: Register SoC device
firmware: tegra: set drvdata earlier
memory: Convert to using %pOF instead of full_name
soc: Convert to using %pOF instead of full_name
bus: Convert to using %pOF instead of full_name
firmware: Convert to using %pOF instead of full_name
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/drivers
Pull "Allwinner driver changes for 4.14" from Chen-Yu Tsai:
Usual driver changes:
- SUNXI_RSB bus driver enabled by default for ARM64
- Support for SRAM controller and SRAM C block on the A64 added
* tag 'sunxi-drivers-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Pull "non-urgent fixes for omaps for v4.14" from Tony Lindgren:
Non-urgent fixes for omaps for v4.14 merge window. These all
can wait for the merge window as we have not seemed to hit
any of these so far:
- Fix error handling in omap_ocp2scp_probe affecting runtime
PM error path
- Drop broken RPM status update for omap_device
- Two fixes for of_irq_get() usage that can return 0
* tag 'omap-for-v4.14/fixes-not-urgent-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: PRM: fix of_irq_get() result checks
ARM: OMAP3+: PRM: fix of_irq_get() result check
ARM: OMAP2+: omap_device: drop broken RPM status update from suspend_noirq
bus: omap-ocp2scp: Fix error handling in omap_ocp2scp_probe
|
|
Allwinner's A64 SoC uses the "Reduced Serial Bus" to communicate with
its companion PMIC.
Since arm64 does not have separate defconfigs for each platform or
processor family, enable this driver by default for ARM64 as well.
Note that the Kconfig symbol already depends on ARCH_SUNXI.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[wens@csie.org: Refined commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When resuming, set up registers that have been lost in the sleep state.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The error handling code in omap_ocp2scp_probe fails to invoke
pm_runtime_disable and fails to initialize return value in
certain cases. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm, I think I've got one later
driver pull for mediatek SoC driver, I'm undecided on if it needs to
go to you yet.
Otherwise summary below:
Core drm:
- Atomic add driver private objects
- Deprecate preclose hook in modern drivers
- MST bandwidth tracking
- Use kvmalloc in more places
- Add mode_valid hook for crtc/encoder/bridge
- Reduce sync_file construction time
- Documentation updates
- New DRM synchronisation object support
New drivers:
- pl111 - pl111 CLCD display controller
Panel:
- Innolux P079ZCA panel driver
- Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels
- panel-samsung-s6e3ha2: Add s6e3hf2 panel support
i915:
- SKL+ watermark fixes
- G4x/G33 reset improvements
- DP AUX backlight improvements
- Buffer based GuC/host communication
- New getparam for (sub)slice infomation
- Cannonlake and Coffeelake initial patches
- Execbuf optimisations
radeon/amdgpu:
- Lots of Vega10 bug fixes
- Preliminary raven support
- KIQ support for compute rings
- MEC queue management rework
- DCE6 Audio support
- SR-IOV improvements
- Better radeon/amdgpu selection support
nouveau:
- HDMI stereoscopic support
- Display code rework for >= GM20x GPUs
msm:
- GEM rework for fine-grained locking
- Per-process pagetable work
- HDMI fixes for Snapdragon 820.
vc4:
- Remove 256MB CMA limit from vc4
- Add out-fence support
- Add support for cygnus
- Get/set tiling ioctls support
- Add T-format tiling support for scanout
zte:
- add VGA support.
etnaviv:
- Thermal throttle support for newer GPUs
- Restore userspace buffer cache performance
- dma-buf sync fix
stm:
- add stm32f429 display support
exynos:
- Rework vblank handling
- Fixup sw-trigger code
sun4i:
- V3s display engine support
- HDMI support for older SoCs
- Preliminary work on dual-pipeline SoCs.
rcar-du:
- VSP work
imx-drm:
- Remove counter load enable from PRE
- Double read/write reduction flag support
tegra:
- Documentation for the host1x and drm driver.
- Lots of staging ioctl fixes due to grate project work.
omapdrm:
- dma-buf fence support
- TILER rotation fixes"
* tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux: (1270 commits)
drm: Remove unused drm_file parameter to drm_syncobj_replace_fence()
drm/amd/powerplay: fix bug fail to remove sysfs when rmmod amdgpu.
amdgpu: Set cik/si_support to 1 by default if radeon isn't built
drm/amdgpu/gfx9: fix driver reload with KIQ
drm/amdgpu/gfx8: fix driver reload with KIQ
drm/amdgpu: Don't call amd_powerplay_destroy() if we don't have powerplay
drm/ttm: Fix use-after-free in ttm_bo_clean_mm
drm/amd/amdgpu: move get memory type function from early init to sw init
drm/amdgpu/cgs: always set reference clock in mode_info
drm/amdgpu: fix vblank_time when displays are off
drm/amd/powerplay: power value format change for Vega10
drm/amdgpu/gfx9: support the amdgpu.disable_cu option
drm/amd/powerplay: change PPSMC_MSG_GetCurrPkgPwr for Vega10
drm/amdgpu: Make amdgpu_cs_parser_init static (v2)
drm/amdgpu/cs: fix a typo in a comment
drm/amdgpu: Fix the exported always on CU bitmap
drm/amdgpu/gfx9: gfx_v9_0_enable_gfx_static_mg_power_gating() can be static
drm/amdgpu/psp: upper_32_bits/lower_32_bits for address setup
drm/amd/powerplay/cz: print message if smc message fails
drm/amdgpu: fix typo in amdgpu_debugfs_test_ib_init
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
|
|
Add compatible string for the ARM CCN-502 interconnect
Signed-off-by: Velibor Markovski <velibor.markovski@broadcom.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "devm_kcalloc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/bus/arm-ccn.ko | grep alias
$
After this patch:
$ modinfo drivers/bus/arm-ccn.ko | grep alias
alias: of:N*T*Carm,ccn-504C*
alias: of:N*T*Carm,ccn-504
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
In fact, it is needed for PCI to work on msm8996 (and probably other
things). No idea why it was depending on renesas but that doesn't make
any sense. So drop the dependency.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
The 7278 introduces a new version of this core. This
commit adds support for that revision.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The ARM64 architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The ARM architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Check for GISB arbitration errors through a chained notifier
when a process dies or a kernel panic occurs. This allows a
meaningful GISB diagnostic message to occur along with other
diagnostic information from the event.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The GISB bus can support addresses beyond 32-bits. So this commit
corrects support for reading a captured 64-bit address into a 64-bit
variable by obtaining the high bits from the ARB_ERR_CAP_HI_ADDR
register (when present) and then outputting the full 64-bit value.
It also removes unused definitions.
Fixes: 44127b771d9c ("bus: add Broadcom GISB bus arbiter timeout/error handler")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This commit corrects the bug introduced in commit f80835875d3d
("bus: brcmstb_gisb: Look up register offsets in a table") such
that gisb_write() translates the register enumeration into an
offset from the base address for writes as well as reads.
Fixes: f80835875d3d ("bus: brcmstb_gisb: Look up register offsets in a table")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
|
|
Since we want this external bus to be available on multi_v7 builds,
set to default ARCH_QCOM so we get it selected whenever QCOM is
enabled.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
I noticed my e-mail address is wrong in this one. This patch fixes it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In case the driver registration fails, the hotplug callback is leaked.
Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.
Fixes: fdc15a36d84e ("bus/arm-ccn: Convert to hotplug statemachine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
|
|
Make sure to drop the reference to the parent device taken by
class_find_device() after populating the bus.
Fixes: 3b9334ac835b ("mfd: vexpress: Convert custom func API to regmap")
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
Pull "DaVinci driver updates for v4.10 (part 2)" from Sekhar Nori:
Fixes for drivers already queued to prevent
section mismatch warnings introduced by them.
* tag 'davinci-for-v4.10/drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
|
|
In order to avoid a section mismatch drop the call to
of_flat_dt_get_machine_name() when printing the error message.
While we're at it: fix a typo.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
bus: Add Tegra GMI support
This provides a driver to enable the use of the Generic Memory Interface
found on Tegra SoCs that can host various types of high-speed devices.
* tag 'tegra-for-4.10-bus' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
bus: Add support for Tegra Generic Memory Interface
dt/bindings: Add bindings for Tegra GMI controller
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Generic Memory Interface bus can be used to connect high-speed
devices such as NOR flash, FPGAs, DSPs...
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Colibri T20/T30 on EvalBoard V3.x and GMI-Memory Board
Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding@nvidia.com: symmetry and coding style OCD]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Create the driver for the da8xx master peripheral priority
configuration and implement support for writing to the three
Master Priority registers on da850 SoCs.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This hides the option for people who do not want their Kconfig
vision cluttered (i.e. x86) and enables compile testing apart
from the supported main arch.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The CCI ports programming interface is available to the kernel
only when booted in secure mode (or when firmware enables
non-secure access to override CCI ports control). In both cases,
firmware reports the CCI ports availability through the device
tree CCI ports nodes, which must be parsed and their status checked
by the kernel probing path.
This check is currently missing and may cause the kernel to
erroneously believe it is free to take control of CCI ports
where in practice CCI ports control is forbidden.
Add the missing CCI port availability check to the CCI driver
in order to guarantee sane CCI usage.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
|
|
After being asked to not depend on ARCH_QCOM* or similar,
unsurprisingly compilation fails on UM as it has no I/O
memory:
drivers/built-in.o: In function `qcom_ebi2_probe':
>> drivers/bus/qcom-ebi2.c:333: undefined reference to
`devm_ioremap_resource'
Fix this by letting the Kconfig atleast depend on HAS_IOMEM.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
Pull "Qualcomm EBI2 bindings and bus driver" from Linus Walleij
* tag 'qcom-ebi2-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
Acked-by: Andy Gross <andy.gross@linaro.org>
|
|
This adds a driver for the Qualcomm External Bus Interface EBI2
found in the MSM8660 and APQ8060 SoCs (at least).
This was tested with the SMSC9112 ethernet on the APQ8060
Dragonboard sitting on top of the SLOW CS2.
Some of my understanding if very vague and based on guesses and
extrapolations: the documentation in APQ8060 Qualcomm Application
Processor User Guide 80-N7150-14 Rev. A describes select features but
does not document the register bit fields.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For one of the CCI events exposed under sysfs, "snoop" was typo'd as
"snopp". Correct this such that users see the expected event name when
enumerating events via sysfs.
Cc: arm@kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160818125731.27256-14-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/1471024183-12666-6-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Cc: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1471024183-12666-5-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.linaro.org/people/pawel.moll/linux into fixes
Merge "bus: ARM CCN PMU driver updates" from Paweł Moll:
- Fixes and improvements for XP watchpoint and events handling
- Added missing condition checks for KVM-related exclusions
- Improved interrupt affinity handling
- Fix for hrtimer use in polling mode
- Event grouping implementation improvement
* tag 'ccn/fixes-for-4.8-v2' of git://git.linaro.org/people/pawel.moll/linux:
bus: arm-ccn: make event groups reliable
bus: arm-ccn: fix hrtimer registration
bus: arm-ccn: fix PMU interrupt flags
bus: arm-ccn: Add missing event attribute exclusions for host/guest
bus: arm-ccn: Correct required arguments for XP PMU events
bus: arm-ccn: Fix XP watchpoint settings bitmask
bus: arm-ccn: Do not attempt to configure XPs for cycle counter
bus: arm-ccn: Fix PMU handling of MN
|
|
The CCN PMU driver leaves the counting logic always enabled, and thus
events are enabled while groups are manipulated. As each event is
stopped and read individually, this leads to arbitrary skew across event
groups, which can be seen if counting several identical events.
To avoid this, implement pmu_{enable,disable} callbacks to stop and
start all counters atomically around event manipulation. As the counters
are now stopped, we cannot poll the cycle counter to wait for events to
drain from the bus. However, as the counters are stopped and the events
will not be read regardless, we can simply allow the bus to drain
naturally.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
The CCN PMU driver has a single hrtimer, used to simulate a periodic
interrupt on systems where the overflow interrupt is not possible to
use. The hrtimer is started when any event is started, and cancelled when
any event is stopped. Thus, stopping a single event is sufficient to
disable to hrtimer, and overflows (of other events) may be lost.
To avoid this, this patch reworks the hrtimer start/cancel to only occur
when the first event is added to a PMU, and the last event removed,
making use of the existing bitmap counting active events.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
Currently the IRQ core is permitted to make the CCN PMU IRQ handler
threaded, and will allow userspace to change the CPU affinity of the
interrupt behind our back. Both of these could violate our
synchronisation requirements with the core perf code, which relies upon
strict CPU affinity and disabling of interrupts to guarantee mutual
exclusion in some cases.
As with the CPU PMU drivers, we should request the interrupt with
IRQF_NOBALANCING and IRQF_NO_THREAD, to avoid these issues.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
CCN PMUs have no knowledge into VM-related origins of the memory
traffic, therefore can't handle requests for host-only or guest-only
events.
Added appropriate exclusions (they should have been there from the
beginning). This required changing the error code returned, as the
userspace tool only re-negotiates the options (exclude_guest is true by
default) only for EINVAL.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
XP can provide events from two sources: watchpoints, observing traffic
on device ports and PMU looking at internal buses.
Unfortunately the sysfs definition of the PMU events was requiring
port number (instead of bus number) and direction (the buses are
unidirectional), as these fields were shared with the watchpoint event.
Although it does not introduce a major problem (port can be used as
bus alias and direction is simply ignored for XP PMU events), it's
better to fix it now, before external tools start depending on this
behaviour.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
