summaryrefslogtreecommitdiff
path: root/drivers/bluetooth/btusb.c
AgeCommit message (Collapse)Author
2015-12-10Bluetooth: btintel: Create common Intel Version Read functionLoic Poulain
The Intel Version Read command is used to retrieve information about hardware and firmware version/revision of Intel Bluetooth controllers. This is an Intel generic command used in USB and UART drivers. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: btintel: Add manufacturing enter/exit helpersLoic Poulain
Older Intel controllers need to enter manufacturing mode to perform some vendor specific operations (patching, configuration...). Add enter/exit manufaturing methods and refactor existing manufacturing code. Exit can be configured to perform a reset. Reset can be performed either with patches activated or deactivated. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Add support of Toshiba Broadcom based devicesDmitry Tunin
BugLink: https://bugs.launchpad.net/bugs/1522949 T: Bus=03 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0225 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=4CBB58034671 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-11-19Bluetooth: Use new hci_skb_pkt_* wrappers for driversMarcel Holtmann
The new hci_skb_pkt_* wrappers are mainly intented for drivers to require less knowledge about bt_cb(sbk) handling. So after converting the core packet handling, convert all drivers. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-11-05Bluetooth: Fix possible deadlock in btusbKuba Pawlak
commit 8f9d02f470f48416444ac3a1eacecdd0f743f1a7 introduced spinlocks in btusb_work. This is run in a context of a worqueue and can be interrupted by hardware irq. If it happens while spinlock is held, we have a deadlock. Solution is to use _irqsave/_resore version of locking [ 466.460560] ================================= [ 466.460565] [ INFO: inconsistent lock state ] [ 466.460572] 4.3.0-rc6+ #1 Tainted: G W [ 466.460576] --------------------------------- [ 466.460582] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. [ 466.460589] kworker/0:2/94 [HC0[0]:SC0[0]:HE1:SE1] takes: [ 466.460595] (&(&data->rxlock)->rlock){?.-...}, at: [<ffffffffa0526923>] btusb_work+0xa3/0x3fd [btusb] [ 466.460621] {IN-HARDIRQ-W} state was registered at: [ 466.460625] [<ffffffff811021b5>] __lock_acquire+0xc45/0x1e80 [ 466.460638] [<ffffffff811040d5>] lock_acquire+0xe5/0x1f0 [ 466.460646] [<ffffffff8182f108>] _raw_spin_lock+0x38/0x50 [ 466.460657] [<ffffffffa0525448>] btusb_recv_intr+0x38/0x170 [btusb] [ 466.460668] [<ffffffffa0525626>] btusb_intr_complete+0xa6/0x130 [btusb] [ 466.460679] [<ffffffff815d8f1e>] __usb_hcd_giveback_urb+0x8e/0x160 [ 466.460690] [<ffffffff815d911f>] usb_hcd_giveback_urb+0x3f/0x120 [ 466.460698] [<ffffffff81606e4d>] uhci_giveback_urb+0xad/0x280 [ 466.460706] [<ffffffff81608f64>] uhci_scan_schedule.part.33+0x6b4/0xbe0 [ 466.460714] [<ffffffff81609b50>] uhci_irq+0xd0/0x180 [ 466.460722] [<ffffffff815d8296>] usb_hcd_irq+0x26/0x40 [ 466.460729] [<ffffffff81117d40>] handle_irq_event_percpu+0x40/0x300 [ 466.460739] [<ffffffff81118040>] handle_irq_event+0x40/0x60 [ 466.460746] [<ffffffff8111af39>] handle_fasteoi_irq+0x89/0x150 [ 466.460754] [<ffffffff8101e0f3>] handle_irq+0x73/0x120 [ 466.460763] [<ffffffff81832f11>] do_IRQ+0x61/0x120 [ 466.460772] [<ffffffff8183084c>] ret_from_intr+0x0/0x31 [ 466.460780] [<ffffffff81697a77>] cpuidle_enter+0x17/0x20 [ 466.460790] [<ffffffff810f62c2>] call_cpuidle+0x32/0x60 [ 466.460800] [<ffffffff810f65a8>] cpu_startup_entry+0x2b8/0x3f0 [ 466.460807] [<ffffffff818214ca>] rest_init+0x13a/0x140 [ 466.460817] [<ffffffff81f76029>] start_kernel+0x4a3/0x4c4 [ 466.460827] [<ffffffff81f75339>] x86_64_start_reservations+0x2a/0x2c [ 466.460837] [<ffffffff81f75485>] x86_64_start_kernel+0x14a/0x16d [ 466.460846] irq event stamp: 754913 [ 466.460851] hardirqs last enabled at (754913): [<ffffffff8182f4cc>] _raw_spin_unlock_irq+0x2c/0x40 [ 466.460861] hardirqs last disabled at (754912): [<ffffffff8182f28d>] _raw_spin_lock_irq+0x1d/0x60 [ 466.460869] softirqs last enabled at (753024): [<ffffffff810aeaa0>] __do_softirq+0x380/0x490 [ 466.460880] softirqs last disabled at (753009): [<ffffffff810aedef>] irq_exit+0x10f/0x120 [ 466.460888] other info that might help us debug this: [ 466.460894] Possible unsafe locking scenario: [ 466.460899] CPU0 [ 466.460903] ---- [ 466.460907] lock(&(&data->rxlock)->rlock); [ 466.460915] <Interrupt> [ 466.460918] lock(&(&data->rxlock)->rlock); [ 466.460926] *** DEADLOCK *** [ 466.460935] 2 locks held by kworker/0:2/94: [ 466.460939] #0: ("events"){.+.+.+}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660 [ 466.460958] #1: ((&data->work)){+.+...}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660 [ 466.460974] Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21Bluetooth: btintel: Enable extra Intel vendor eventsMarcel Holtmann
The Intel Bluetooth controllers can emit extra vendor specific events in error conditions or for debugging purposes. To make the life easier for engineers, enable them by default. When the vendor_diag options has been enabled, then additional debug events are also enabled. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Set manufacturer for Intel bootloader devicesMarcel Holtmann
For Intel bootloader devices, set the manufacturer information so that it becomes possible to decode the boot process. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Add support for latest Apple controllersMarcel Holtmann
The latest Apple Bluetooth controllers with Broadcom chip in it have a small design change. Instead of including a USB hub with mouse and keyboard devices, they are now HID interfaces on the same device. T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 39 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=05ac ProdID=8290 Rev= 0.79 S: Manufacturer=Broadcom Corp. S: Product=Bluetooth USB Host Controller C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA A: FirstIf#= 2 IfCount= 4 Cls=ff(vend.) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid E: Ad=85(I) Atr=03(Int.) MxPS= 8 Ivl=10ms I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=10ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 3 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 3 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 3 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 3 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 3 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) The general layout of Bluetooth devices is that interface 0 is the main interface and interface 1 is for audio data. This design obviously moves it to main interface 2 and audio data on interface 3. Starting with the MacBookPro12,1 (early 2015 models) the new Broadcom BCM943602CS cards are used which show this interface layout. usb 4-1.5: New USB device found, idVendor=05ac, idProduct=8290 usb 4-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-1.5: Product: Bluetooth USB Host Controller usb 4-1.5: Manufacturer: Broadcom Corp. Bluetooth: hci0: BCM: chip id 102 build 0243 Bluetooth: hci0: BCM: product 05ac:8290 Bluetooth: hci0: BCM20703A1 Generic USB UHE Apple 20Mhz fcbga_X87 Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Set early vendor info for Intel and BroadcomMarcel Holtmann
For the controllers from Intel and Broadcom (including Apple), it is helpful to have the information about the manufacturer send out early. This patch sets the hdev->manufacturer information which will be send out before actually calling the vendor specific hdev->setup driver callback. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: ath3k: Add support of AR3012 0cf3:817b deviceDmitry Tunin
T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=817b Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1506615 Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-10-21Bluetooth: ath3k: Add new AR3012 0930:021c idDmitry Tunin
This adapter works with the existing linux-firmware. T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=021c Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1502781 Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-10-21Bluetooth: btusb: Add support for Foxconn/Lenovo BCM43142A0 (105b:e065)Santtu Rekilä
Recently salvaged this 'BCM43142A0' WiFi/Bluetooth module from a Lenovo laptop and noticed it doesn't work automatically, because the USB IDs are missing from btusb.c. Plugging in the adapter on Linux 4.1 (dmesg): usb 3-3.3.3: new full-speed USB device number 90 using xhci_hcd usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065 usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 3-3.3.3: Product: BCM43142A0 usb 3-3.3.3: Manufacturer: Broadcom Corp usb 3-3.3.3: SerialNumber: 0090A286559E /sys/kernel/debug/usb/devices: T: Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 90 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=105b ProdID=e065 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=0090A286559E C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Support for the chipset was added in commit 88f9b65 and a similar BCM43142 based device was added in commit 8f0c304. To work around the issue, I got the firmware (BCM43142A0_001.001.011.0122.0153) off a Windows installation of Broadcom bluetooth driver and converted it to a .hcd -file via. hex2hcd and placed it in /lib/firmware/brcm/BCM.hcd. After that: $ echo "105b e065 0 19ff 0239" > /sys/bus/usb/drivers/btusb/new_id ...(plug in the adapter) usb 3-3.3.3: new full-speed USB device number 91 using xhci_hcd usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065 usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 3-3.3.3: Product: BCM43142A0 usb 3-3.3.3: Manufacturer: Broadcom Corp usb 3-3.3.3: SerialNumber: 0090A286559E Bluetooth: hci0: BCM: chip id 70 Bluetooth: hci0: BCM (001.001.011) build 0000 bluetooth hci0: firmware: direct-loading firmware brcm/BCM.hcd Bluetooth: hci0: BCM (001.001.011) build 0154 Bam, now it works for me! /sys/kernel/debug/usb/devices: T: Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 92 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=105b ProdID=e065 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=0090A286559E C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Santtu Rekilä <sare@r00t3d.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21Bluetooth: btusb: Mark BCM2045 devices to have broken link key commandsMarcel Holtmann
The BCM2045 seems to have a problem with the stored link key commands and thus just mark them as broken. HCI Event: Command Complete (0x0e) plen 12 Read Local Supported Features (0x04|0x0003) ncmd 1 status 0x00 Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80 HCI Event: Command Complete (0x0e) plen 12 Read Local Version Information (0x04|0x0001) ncmd 1 status 0x00 HCI Version: 2.0 (0x3) HCI Revision: 0x2000 LMP Version: 2.0 (0x3) LMP Subversion: 0x410d Manufacturer: Broadcom Corporation (15) HCI Event: Command Complete (0x0e) plen 11 Read Buffer Size (0x04|0x0005) ncmd 1 status 0x00 ACL MTU 1017:8 SCO MTU 64:0 HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 status 0x00 Commands: ffffff03feffcfffffffffff0300f8ff07 HCI Event: Command Complete (0x0e) plen 4 Delete Stored Link Key (0x03|0x0012) ncmd 1 status 0x11 deleted 2048 Error: Unsupported Feature or Parameter Value From the looks of it, this device seems genuine and not one of the devices that are neither Broadcom nor CSR devices in reality. T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=2045 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM2045A S: SerialNumber=000000000000 C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none) Reported-and-tested-by: Julio González Mejías <juliolokooo@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btintel: Add diagnostic support for older controllersMarcel Holtmann
For the older controllers like Wilkens Peak and Stone Peak, enabling the traces requires to switch into manufacturer mode first. This patch does exactly that, but only for these older controllers. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btintel: Set quirk for non-persistent diagnostic settingsMarcel Holtmann
For Intel controllers the diagnostics settings are not persistent over HCI Reset. So set the quirk to programm them again on every power up. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Print information of Intel SfP lock statesMarcel Holtmann
The lock states from Intel SfP controllers can only be read once before loading the firmware. So for debugging purposes, print them out. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btintel: Add support for enabling tracing functionalityMarcel Holtmann
For Intel controllers with firmware that allows tracing of baseband functionality this allows enabling it via set_diag driver callback. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Add support for Broadcom LM_DIAG interfaceMarcel Holtmann
The Broadcom Bluetooth USB devices have a third interface that is dedicated for LM_DIAG messages. The If#= 2 describes this interface and it consists of one bulk in and one bulk endpoint. T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 38 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=19ff ProdID=0239 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) For all Broadcom based devices with this interface, the driver now claims it and schedules URBs for it. This allows to capture the LM_DIAG messages and allows forwarding them via hci_recv_diag into the diagnostic channel of the Bluetooth subsystem. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-05Bluetooth: Move handling of HCI_RUNNING flag into coreMarcel Holtmann
Setting and clearing of HCI_RUNNING flag in each and every driver is just duplicating the same code all over the place. So instead of having the driver do it in their hdev->open and hdev->close callbacks, set it globally in the core transport handling. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-05Bluetooth: Move HCI_RUNNING check into hci_send_frameMarcel Holtmann
In all callbacks for hdev->send the status of HCI_RUNNING is checked. So instead of repeating that code in every driver, move the check into the hci_send_frame function before calling hdev->send. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-09-17Bluetooth: Remove SCO fragments on connection closeKuba Pawlak
SCO packet reassembler may have a fragment of SCO packet, from previous connection, cached and not removed when SCO connection is ended. Packets from new SCO connection are then going to be attached to that fragment, creating an invalid SCO packets. Controllers like Intel's WilkinsPeak are always fragmenting SCO packet into 3 parts (#1, #2, #3). Packet #1 contains SCO header and audio data, others just audio data. if there is a fragment cached from previous connection, i.e. #1, first SCO packet from new connection is going to be attached to it creating packet consisting of fragments #1-#1-#2. This will be forwarded to upper layers. After that, fragment #3 is going to be used as a starting point for another SCO packet. It does not contain a SCO header, but the code expects it, casts a SCO header structure on it, and reads whatever audio data happens to be there as SCO packet length and handle. From that point on, we are assembling random data into SCO packets. Usually it recovers quickly as initial audio data contains mostly zeros (muted stream), but setups of over 4 seconds were observed. Issue manifests itself by printing on the console: Bluetooth: hci0 SCO packet for unknown connection handle 48 Bluetooth: hci0 SCO packet for unknown connection handle 2560 Bluetooth: hci0 SCO packet for unknown connection handle 12288 It may also show random handles if audio data was non-zeroed. Hcidump shows SCO packets with random length and handles. Few messages with handle 0 at connection creation are OK for some controllers (like WilkinsPeak), as there are SCO packets with zeroed handle at the beginning (possible controller bug). Few of such messages at connection end, with a handle looking sane (around 256, 512, 768 ...) is also OK, as these are last SCO packets that were assembled and sent up, before connection was ended, but were not handled in time. This issue may still manifest itself on WilkinsPeak as it sometimes, at SCO connection creation, does not send third fragment of first SCO packet (#1-#2-#1-#2-#3...). This is a firmware bug and this patch does not address it. Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-17Bluetooth: btusb: Use btintel_load_ddc_config for device configLoic Poulain
btintel_load_ddc_config is now part of btintel. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-17Bluetooth: btusb: Detect new kind of counterfeit CSR controllersJohan Hedberg
Controllers claiming to be CSR with LMP subversion 0x0c5c don't actually seem to be authentic CSR controllers. They also don't have their USB bcdDevice value matching the LMP subversion like all other CSR controllers: HCI: > HCI Event: Command Complete (0x0e) plen 12 Read Local Version Information (0x04|0x0001) ncmd 1 Status: Success (0x00) HCI version: Bluetooth 2.0 (0x03) - Revision 3164 (0x0c5c) LMP version: Bluetooth 2.0 (0x03) - Subversion 3164 (0x0c5c) Manufacturer: Cambridge Silicon Radio (10) USB: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=16 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev= 1.34 C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms These controllers also have the HCI_Read_Stored_Link_Key command broken so it's important the right quirk is set for them. Reported-and-tested-by: Rhobison Alves Pereira <rhobison@hotmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-28Bluetooth: btusb: Correct typos based on checkpatch.plMinjune Kim
Signed-off-by: Minjune Kim <infinite.minjune.kim@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-15Bluetooth: btusb: mark 0c10:0000 devices with BTUSB_SWAVEPeter Poklop
This patch enables quirk handling for Silicon Wave based devices and fixes kernel bug with id 42985. T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0c10 ProdID=0000 Rev=15.00 S: Manufacturer=SiW S: Product=SiW S: SerialNumber=340A05F61100 C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Peter Poklop <peter.poklop@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30Bluetooth: btusb: match generic class code in interface descriptorDaniel Drake
btusb currently has a generic match on USB device descriptors: { USB_DEVICE_INFO(0xe0, 0x01, 0x01) }, However, http://www.usb.org/developers/defined_class states: Base Class E0h (Wireless Controller) This base class is defined for devices that are Wireless controllers. Values not shown in the table below are reserved. These class codes are to be used in Interface Descriptors, with the exception of the Bluetooth class code which can also be used in a Device Descriptor. Add a match on the interface descriptors accordingly. This fixes compatibility with the RTL8723AU device shown below. This device conforms to the USB Interface Association Descriptor specification, which requires the device to have class ef/02/01. The extra IAD descriptor then specifies that interfaces 0 and 1 belong to the same function/driver, which is true. Provided that the Bluetooth device class spec accepts use of the IAD, I imagine that technically, all btusb devices should be configured like this. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=0724 Rev= 2.00 S: Manufacturer=Realtek S: Product=802.11n WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723au E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=500us Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-23Bluetooth: btintel: Create common function for Intel version infoMarcel Holtmann
The Intel version information is shared between USB and UART drivers and with that move it into a generic function of the Intel module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-07-23Bluetooth: btintel: Create common Intel Secure Send functionMarcel Holtmann
The Intel Secure Send command is used the same in USB and UART drivers and with that move a generic version into the Intel module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-07-23Bluetooth: btusb: Use hardware error handler from Intel moduleMarcel Holtmann
The Intel specific Bluetooth module provides now an exported function for the hardware error. Use that instead of duplicating it inside the driver. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-06-18Bluetooth: ath3k: Add support of 04ca:300d AR3012 deviceDmitry Tunin
BugLink: https://bugs.launchpad.net/bugs/1394368 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300d Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-06-17Bluetooth: btusb: Add routine for applying Intel DDC parametersTedd Ho-Jeong An
This patch adds the routine to apply the DDC parameter from device specific ddc file. Once the device is rest to operational mode, optionally, it can download the device specific configration (DDC) parameters before the BlueZ starts the stack initialization. It opens the DDC file based on HW_VARIANT and DEV_REVISION and send ID/Value with HCI_Intel_Write_DDC command. Format of DDC file DDC file contains one or more number of DDC structure. DDC Structure It has 'Length' field of one octet, DDC 'ID' field of two octets followed by the array of DDC 'Value' that gives the value of parameters itself. 'Length' contains the length of DDC 'ID' and DDC 'Value'. +------------+----------+ | Size(byte) | Name | +------------+----------+ | 1 | Length | +------------+----------+ | 2 | ID | +------------+----------+ | Length - 2 | Value | +------------+----------+ Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-06-09Bluetooth: btusb: Fix secure send command length alignment on Intel 8260Marcel Holtmann
This patch fixes the command length alignment issue for Intel Bluetooth 8260. The length of parameters in the firmware downloading command must be multiplication of 4. If not, the command must append Intel_NOP command with extra parameters, zeros, at the end, and the firmware file is already included Intel_NOP command for alignment. This patch checks the next command and if the next command is Intel_NOP command, it reads the Intel_NOP command and send them together. For example, if the data from the firmware file looks like this: 8E FC 03 11 22 33 02 FC 03 00 00 00 Previously, btusb sends two commands: 09 FC 06 8E FC 03 11 22 33 09 FC 06 02 FC 03 00 00 00 This won't work because the length of parameters are 6 which violates the 4 byte alignment. This patch will append them together and send as one command: 09 FC 0C 8E FC 03 11 22 33 02 FC 03 00 00 00 Based on previous work from Tedd Ho-Jeong An <tedd.an@intel.com> Reported-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
2015-06-08Bluetooth: btusb: Correct typo in Roper Class 1 Bluetooth DongleAleksei Volkov
That patch corrects the typo in usb vendor id for Roper Class 1 Bluetooth Dongle. Problem with typo is present since 4.0 kernel. Content /sys/kernel/debug/usb/devices for these dongle: T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1310 ProdID=0001 Rev=15.00 S: Manufacturer=SiW S: Product=SiW S: SerialNumber=E7BB050D0B00 C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Aleksei Volkov <info@dv2c.ru> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org # 4.0.x
2015-06-08Bluetooth: btusb: Remove unneeded btusb_read_local_version functionMarcel Holtmann
The btusb_read_local_version function has only a single user and with that just move its functionality in place where it belongs. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-06-08Bluetooth: btusb: Remove double error check from local version commandMarcel Holtmann
The __hci_cmd_sync function already handles the command status and command complete errors. No need to check the status field again. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-06-08Bluetooth: btusb: Fix memory leak in Intel setup routineMarcel Holtmann
The SKB returned from the Intel specific version information command is missing a kfree_skb. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
2015-06-07ath3k: add support of 13d3:3474 AR3012 deviceDmitry Tunin
BugLink: https://bugs.launchpad.net/bugs/1427680 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3474 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-06-07ath3k: Add support of 0489:e076 AR3012 deviceDmitry Tunin
BugLink: https://bugs.launchpad.net/bugs/1462614 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=06 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e076 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-05-30Merge branch 'for-upstream' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2015-05-28 Here's a set of patches intended for 4.2. The majority of the changes are on the 802.15.4 side of things rather than Bluetooth related: - All sorts of cleanups & fixes to ieee802154 and related drivers - Rework of tx power support in ieee802154 and its drivers - Support for setting ieee802154 tx power through nl802154 - New IDs for the btusb driver - Various cleanups & smaller fixes to btusb - New btrtl driver for Realtec devices - Fix suspend/resume for Realtek devices Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-25Bluetooth: btusb: fix Realtek suspend/resumeDaniel Drake
Realtek btusb devices don't currently work after suspend/resume because the updated firmware is quietly lost - the USB hub doesn't notice any status change upon resume, but some kind of reset has definitely happened as the LMP subversion has reverted to its original value. Set the reset_resume flag to trigger probe and upload the new firmware again. Like the vendor code, I assume this is not needed when the device is selected as a wakeup source and hence will retain power during suspend. On the 2 products I have to hand, when trying this configuration the hardware seems unable to keep the device powered up during suspend. The USB hub then detects a status change on resume and does a reset, so we do not end up in broken state. Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-25Bluetooth: btusb: Change 1 to true in bool type variable assignmentShailendra Verma
The reset is a bool type variable. So assigning true to reset instead of 1. Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-25Bluetooth: btusb: Support QCA61x4 ROME v2.0Chan-yeol Park
The previous commit(3267c88) missed QCA61x4 ROME v2.0 info on Samsung so its BT is not activated and the below message is shown. [ 8.009638] usb 1-1: New USB device found, idVendor=0cf3, idProduct=e300 [ 8.012637] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 8.102901] Bluetooth: hci0: don't support firmware rome 0x200 This patch adds QCA61x4 ROME v2.0 info in qca_devices_table[], and is verified on Samsung with the firmware provided by Kim, Ben Young Tae <ytkim@qca.qualcomm.com>. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e300 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-15Bluetooth: btusb: Fix calls to __hci_cmd_sync()Frederic Danis
Remove test of command reply status as it is already performed by __hci_cmd_sync(). __hci_cmd_sync_ev() function already returns an error if it got a non-zero status either through a Command Complete or a Command Status event. For both of these events the status is collected up in the event handlers called by hci_event_packet() and then passed as the second parameter to req_complete_skb(). The req_complete_skb() callback in turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores the status in hdev->req_result. The hdev->req_result is then further converted through bt_to_errno() back in __hci_cmd_sync_ev(). Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-14Bluetooth: btrtl: Create separate module for Realtek BT driverCarlo Caione
As already done for btintel and btbcm export setup as separate function in a vendor-specific module to hold all the Realtek specific commands. Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-13Bluetooth: ath3k: add support of 04ca:300f AR3012 deviceDmitry Tunin
BugLink: https://bugs.launchpad.net/bugs/1449730 T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300f Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-13Bluetooth: btusb: Add support for 0cf3:e007Wen-chien Jesse Sung
Device 0cf3:e007 is one of the QCA ROME family. T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e007 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-13Bluetooth: ath3k: Add a new ID 0cf3:e006 to ath3k listWen-chien Jesse Sung
Device info in /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e006 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-04-30Bluetooth: btusb: off by one in rtl8723b_parse_firmware()Dan Carpenter
The ">" should be ">=" so that we don't read past the end of the array. Fixes: 9d9a113e3695 ('Bluetooth: btusb: Add Realtek 8723A/8723B/8761A/8821A support') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-04-30Bluetooth: btusb: Fix two coding style issuesMarcel Holtmann
ERROR: spaces required around that '<' (ctx:WxV) + if (err <0) ^ ERROR: code indent should use tabs where possible +^I^I^I^I sizeof(ver));$ Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-30Bluetooth: btusb: Add Realtek 8723A/8723B/8761A/8821A supportDaniel Drake
Realtek ship a variety of bluetooth USB devices that identify themselves with standard USB Bluetooth device class values, but require a special driver to actually work. Without that driver, you never get any scan results. More recently however, Realtek appear to have wisened up and simply posted a firmware update that makes these devices comply with normal btusb protocols. The firmware needs to be uploaded on each boot. Based on Realtek code from https://github.com/lwfinger/rtl8723au_bt ('new' branch). This enables bluetooth support in the Gigabyte Brix GB-BXBT-2807 which has this RTL8723BE USB device: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3410 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms There is no change to the USB descriptor after firmware update, however the version read by HCI_OP_READ_LOCAL_VERSION changes from 0x8723 to 0x3083. This has also been tested on RTL8723AE and RTL8821AE. Support for RTL8761A has also been added, but that is untested. Signed-off-by: Daniel Drake <drake@endlessm.com> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-22 23:01:55 +0000