summaryrefslogtreecommitdiff
path: root/drivers/bluetooth/btusb.c
AgeCommit message (Collapse)Author
2018-12-19Bluetooth: btusb: Add support for Intel bluetooth device 8087:0029Raghuram Hegde
Include the new USB product ID for Intel Bluetooth device 22260 family(CcPeak) The /sys/kernel/debug/usb/devices portion for this device is: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0029 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com> Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-12-19Bluetooth: Remove unnecessary smp_mb__after_atomic() barriersAndrea Parri
The barriers are redundant because atomic_test_and_clear_bit() already provides the required full ordering for the cases in question (that is, when the bit is cleared). Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-10-18Bluetooth: btusb: Add support for 0cf3:535b QCA_ROME deviceOwen Lin
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=535b Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms Signed-off-by: Owen Lin <olin@rivetnetworks.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27Bluetooth: btusb: Add quirk for BTUSB_INTEL_NEWJustin TerAvest
Intel "new" controllers can do both LE scan and BR/EDR inquiry at once. Signed-off-by: Justin TerAvest <teravest@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-03Bluetooth: btusb: Use bt_dev_err for Intel firmware loading errorsMarcel Holtmann
Replace the BT_ERR functions with bt_dev_err to get a consistent error printout that always prefixes the HCI device identifier. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2018-08-03Bluetooth: btusb: Release RF resource on BT shutdownAmit K Bag
Issue description: Intel 7265 shares the same RF with Wifi and BT. In the shutdown scenario turn off BT, followed by turn WiFi off and on causing error in RF calibration in WiFi Module Solution: before shutdown BT ensure any RF activity to clear by HCI reset command. Reference Logs: ERR kernel: [ 386.193284] iwlwifi 0000:01:00.0: Failed to run INIT calibrations: -5 ERR kernel: [ 386.193298] iwlwifi 0000:01:00.0: Failed to run INIT ucode: -5 ERR kernel: [ 386.193309] iwlwifi 0000:01:00.0: Failed to start RT ucode: -5 Signed-off-by: Amit K Bag <amit.k.bag@intel.com> Singed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-23bluetooth: btusb: Replace GFP_ATOMIC with GFP_KERNEL in inject_cmd_complete()Jia-Ju Bai
inject_cmd_complete() is only called by btusb_send_frame_intel(), which is set to hdev->send, and hdev->send() is never called in atomic context. inject_cmd_complete() calls bt_skb_alloc() with GFP_ATOMIC, which is not necessary. GFP_ATOMIC can be replaced with GFP_KERNEL. This is found by a static analysis tool named DCNS written by myself. I also manually check the kernel code before reporting it. Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: btusb: use irqsave() in URB's complete callbackSebastian Andrzej Siewior
The USB completion callback does not disable interrupts while acquiring the ->lock. We want to remove the local_irq_disable() invocation from __usb_hcd_giveback_urb() and therefore it is required for the callback handler to disable the interrupts while acquiring the lock. The callback may be invoked either in IRQ or BH context depending on the USB host controller. Use the _irqsave variant of the locking primitives. Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: linux-bluetooth@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Add a new Realtek 8723DE ID 0bda:b009Jian-Hong Pan
Without this patch we cannot turn on the Bluethooth adapter on HP 14-bs007la. T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=b009 Rev= 2.00 S: Manufacturer=Realtek S: Product=802.11n WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-30Bluetooth: btusb: Add additional device ID for RTL8822BEArtiom Vaskov
The Asus ROG GL702ZC laptop contains a Realtek RTL8822BE device with an associated BT chip using a USB ID of 13d3:3526. This ID is added to the driver. The /sys/kernel/debug/usb/devices portion for this device is: T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=04 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3526 Rev= 1.10 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Artiom Vaskov <velemas@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-29Bluetooth: btusb: Add Dell Inspiron 5565 to btusb_needs_reset_resume_tableHans de Goede
The Dell Inspiron 5565 uses a QCA Rome chip which needs to be reset (and have its firmware reloaded) for bluetooth to work after suspend/resume. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=15750392 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-29Bluetooth: btusb: Apply QCA Rome patches for some ATH3012 modelsTakashi Iwai
In commit f44cb4b19ed4 ("Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174") we tried to address the non-working Atheros BT devices by changing the quirk from BTUSB_ATH3012 to BTUSB_QCA_ROME. This made such devices working while it turned out to break other existing chips with the very same USB ID, hence it was reverted afterwards. This is another attempt to tackle the issue. The essential point to use BTUSB_QCA_ROME is to apply the btusb_setup_qca() and do RAM- patching. And the previous attempt failed because btusb_setup_qca() returns -ENODEV if the ROM version doesn't match with the expected ones. For some devices that have already the "correct" ROM versions, we may just skip the setup procedure and continue the rest. So, the first fix we'll need is to add a check of the ROM version in the function to skip the setup if the ROM version looks already sane, so that it can be applied for all ath devices. However, the world is a bit more complex than that simple solution. Since BTUSB_ATH3012 quirk checks the bcdDevice and bails out when it's 0x0001 at the beginning of probing, so the device probe always aborts here. In this patch, we add another check of ROM version again, and if the device needs patching, the probe continues. For that, a slight refactoring of btusb_qca_send_vendor_req() was required so that the probe function can pass usb_device pointer directly before allocating hci_dev stuff. Fixes: commit f44cb4b19ed4 ("Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174") Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1082504 Tested-by: Ivan Levshin <ivan.levshin@microfocus.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-29Bluetooth: btusb: Add a new Realtek 8723DE ID 2ff8:b011Jian-Hong Pan
Without this patch we cannot turn on the Bluethooth adapter on ASUS E406MA. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2ff8 ProdID=b011 Rev= 2.00 S: Manufacturer=Realtek S: Product=802.11n WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: Add a new 13d3:3496 QCA_ROME deviceJoão Paulo Rechi Vita
Without this patch we can't establish a SCO connection with this adapter. This adapter is named "IMC Networks" under lsusb. T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3496 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: btusb: add ID for LiteOn 04ca:301aVic Wei
Contains a QCA6174A chipset, with USB BT. Let's support loading firmware on it. From usb-devices: T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=301a Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Vic Wei <vwei@codeaurora.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-04-30Bluetooth: btusb: Add Dell XPS 13 9360 to btusb_needs_reset_resume_tableHans de Goede
The Dell XPS 13 9360 uses a QCA Rome chip which needs to be reset (and have its firmware reloaded) for bluetooth to work after suspend/resume. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Cc: stable@vger.kernel.org Cc: Garrett LeSage <glesage@redhat.com> Reported-and-tested-by: Garrett LeSage <glesage@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-04-30Bluetooth: btusb: Only check needs_reset_resume DMI table for QCA rome chipsetsHans de Goede
Jeremy Cline correctly points out in rhbz#1514836 that a device where the QCA rome chipset needs the USB_QUIRK_RESET_RESUME quirk, may also ship with a different wifi/bt chipset in some configurations. If that is the case then we are needlessly penalizing those other chipsets with a reset-resume quirk, typically causing 0.4W extra power use because this disables runtime-pm. This commit moves the DMI table check to a btusb_check_needs_reset_resume() helper (so that we can easily also call it for other chipsets) and calls this new helper only for QCA_ROME chipsets for now. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Cc: stable@vger.kernel.org Cc: Jeremy Cline <jcline@redhat.com> Suggested-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-04-30Revert "Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174"Hans de Goede
Commit f44cb4b19ed4 ("Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174") is causing bluetooth to no longer work for several people, see: https://bugzilla.redhat.com/show_bug.cgi?id=1568911 So lets revert it for now and try to find another solution for devices which need the modified quirk. Cc: stable@vger.kernel.org Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-04-01Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROMEVic Wei
QCA Rome controllers can do both LE scan and BR/EDR inquiry at once. Signed-off-by: Vic Wei <vwei@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-04-01Bluetooth: btusb: Add USB ID 7392:a611 for Edimax EW-7611ULBVicente Bergas
This WiFi/Bluetooth USB dongle uses a Realtek chipset, so, use btrtl for it. Product information: https://wikidevi.com/wiki/Edimax_EW-7611ULB From /sys/kernel/debug/usb/devices T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=7392 ProdID=a611 Rev= 2.00 S: Manufacturer=Realtek S: Product=Edimax Wi-Fi N150 Bluetooth4.0 USB Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 6 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723bu E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=500us E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Tested-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-03-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Fun set of conflict resolutions here... For the mac80211 stuff, these were fortunately just parallel adds. Trivially resolved. In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the function phy_disable_interrupts() earlier in the file, whilst in 'net-next' the phy_error() call from this function was removed. In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the 'rt_table_id' member of rtable collided with a bug fix in 'net' that added a new struct member "rt_mtu_locked" which needs to be copied over here. The mlxsw driver conflict consisted of net-next separating the span code and definitions into separate files, whilst a 'net' bug fix made some changes to that moved code. The mlx5 infiniband conflict resolution was quite non-trivial, the RDMA tree's merge commit was used as a guide here, and here are their notes: ==================== Due to bug fixes found by the syzkaller bot and taken into the for-rc branch after development for the 4.17 merge window had already started being taken into the for-next branch, there were fairly non-trivial merge issues that would need to be resolved between the for-rc branch and the for-next branch. This merge resolves those conflicts and provides a unified base upon which ongoing development for 4.17 can be based. Conflicts: drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f9524 (IB/mlx5: Fix cleanup order on unload) added to for-rc and commit b5ca15ad7e61 (IB/mlx5: Add proper representors support) add as part of the devel cycle both needed to modify the init/de-init functions used by mlx5. To support the new representors, the new functions added by the cleanup patch needed to be made non-static, and the init/de-init list added by the representors patch needed to be modified to match the init/de-init list changes made by the cleanup patch. Updates: drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function prototypes added by representors patch to reflect new function names as changed by cleanup patch drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init stage list to match new order from cleanup patch ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-15Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174Takashi Iwai
The Atheros 1525/QCA6174 BT doesn't seem working properly on the recent kernels, as it tries to load a wrong firmware ar3k/AthrBT_0x00000200.dfu and it fails. This seems to have been a problem for some time, and the known workaround is to apply BTUSB_QCA_ROM quirk instead of BTUSB_ATH3012. The device in question is: T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=3004 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1082504 Reported-by: Ivan Levshin <ivan.levshin@microfocus.com> Tested-by: Ivan Levshin <ivan.levshin@microfocus.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-03-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
All of the conflicts were cases of overlapping changes. In net/core/devlink.c, we have to make care that the resouce size_params have become a struct member rather than a pointer to such an object. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-01Bluetooth: btusb: Add Dell OptiPlex 3060 to btusb_needs_reset_resume_tableKai-Heng Feng
The issue can be reproduced before commit fd865802c66b ("Bluetooth: btusb: fix QCA Rome suspend/resume") gets introduced, so the reset resume quirk is still needed for this system. T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e007 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Cc: stable@vger.kernel.org Cc: Brian Norris <briannorris@chromium.org> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-03-01Bluetooth: btusb: Remove Yoga 920 from the btusb_needs_reset_resume_tableHans de Goede
Commit 1fdb92697469 ("Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking"), added the Lenovo Yoga 920 to the btusb_needs_reset_resume_table. Testing has shown that this is a false positive and the problems where caused by issues with the initial fix: commit fd865802c66b ("Bluetooth: btusb: fix QCA Rome suspend/resume"), which has already been reverted. So the QCA Rome BT in the Yoga 920 does not need a reset-resume quirk at all and this commit removes it from the btusb_needs_reset_resume_table. Note that after this commit the btusb_needs_reset_resume_table is now empty. It is kept around on purpose, since this whole series of commits started for a reason and there are actually broken platforms around, which need to be added to it. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 1fdb92697469 ("Bluetooth: btusb: Use DMI matching for QCA ...") Cc: stable@vger.kernel.org Cc: Brian Norris <briannorris@chromium.org> Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Kevin Fenzi <kevin@scrye.com> Suggested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-02-25Bluetooth: btusb: Use DMI matching for QCA reset_resume quirkingHans de Goede
Commit 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume fix with a "rewritten" version") applied the USB_QUIRK_RESET_RESUME to all QCA USB Bluetooth modules. But it turns out that the resume problems are not caused by the QCA Rome chipset, on most platforms it resumes fine. The resume problems are actually a platform problem (likely the platform cutting all power when suspended). The USB_QUIRK_RESET_RESUME quirk also disables runtime suspend, so by matching on usb-ids, we're causing all boards with these chips to use extra power, to fix resume problems which only happen on some boards. This commit fixes this by applying the quirk based on DMI matching instead of on usb-ids, so that we match the platform and not the chipset. Here is the /sys/kernel/debug/usb/devices for the Bluetooth module: T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e300 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume..") Cc: stable@vger.kernel.org Cc: Brian Norris <briannorris@chromium.org> Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Reported-and-tested-by: Kevin Fenzi <kevin@scrye.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-02-11Bluetooth: btusb: Add device ID for RTL8822BELarry Finger
The Asus Z370-I contains a Realtek RTL8822BE device with an associated BT chip using a USB ID of 0b05:185c. This device is added to the driver. Signed-off-by: Hon Weng Chong <honwchong@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-02-07Bluetooth: btusb: Add support for Intel Bluetooth device 22560 [8087:0026]Tedd Ho-Jeong An
The Intel Bluetooth device 22560 family (HarrisonPeak, QnJ, and IcyPeak) use the same firmware loading mechanism as previous generation, so include new USB product ID and whitelist the hardware variant. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0026 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-01-25Bluetooth: btintel: Create common function for firmware downloadTedd Ho-Jeong An
The firmware download flow for RAM SKU is same for both USB and UART and this patch creates a common function for both driver. Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-01-24Bluetooth: btintel: Create common Intel Read Boot Params functionTedd Ho-Jeong An
The Intel_Read_Boot_Params command is used to read boot parameters from the bootloader and this is Intel generic command used in USB and UART drivers. Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-01-24Bluetooth: btintel: Use boot parameter from firmware fileTedd Ho-Jeong An
Each RAM SKU has a different boot parameter which is used in HCI_Intel_Reset command after downloading the firmware. The boot parameter is embedded in the firmware data and to support multiple SKUs, driver reads the boot parameter while downloading the firmware instead of using static values per SKU. Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-01-24Bluetooth: btintel: Create common function for Intel ResetTedd Ho-Jeong An
The Intel_Reset command is used to reset the device after downloading the firmware and this is Intel generic command used in both USB and UART. Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-01-08Bluetooth: btusb: Restore QCA Rome suspend/resume fix with a "rewritten" versionHans de Goede
Commit 7d06d5895c15 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"") removed the setting of the BTUSB_RESET_RESUME quirk for QCA Rome devices, instead favoring adding USB_QUIRK_RESET_RESUME quirks in usb/core/quirks.c. This was done because the DIY BTUSB_RESET_RESUME reset-resume handling has several issues (see the original commit message). An added advantage of moving over to the USB-core reset-resume handling is that it also disables autosuspend for these devices, which is similarly broken on these. But there are 2 issues with this approach: 1) It leaves the broken DIY BTUSB_RESET_RESUME code in place for Realtek devices. 2) Sofar only 2 of the 10 QCA devices known to the btusb code have been added to usb/core/quirks.c and if we fix the Realtek case the same way we need to add an additional 14 entries. So in essence we need to duplicate a large part of the usb_device_id table in btusb.c in usb/core/quirks.c and manually keep them in sync. This commit instead restores setting a reset-resume quirk for QCA devices in the btusb.c code, avoiding the duplicate usb_device_id table problem. This commit avoids the problems with the original DIY BTUSB_RESET_RESUME code by simply setting the USB_QUIRK_RESET_RESUME quirk directly on the usb_device. This commit also moves the BTUSB_REALTEK case over to directly setting the USB_QUIRK_RESET_RESUME on the usb_device and removes the now unused BTUSB_RESET_RESUME code. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 7d06d5895c15 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"") Cc: stable@vger.kernel.org Cc: Leif Liddy <leif.linux@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Brian Norris <briannorris@chromium.org> Cc: Daniel Drake <drake@endlessm.com> Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-01-08Bluetooth: btusb: Add support for 0cf3:e010AceLan Kao
Device 0cf3:e010 is one of the QCA ROME family. T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e010 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-26Revert "Bluetooth: btusb: fix QCA Rome suspend/resume"Kai-Heng Feng
This reverts commit fd865802c66bc451dc515ed89360f84376ce1a56. This commit causes a regression on some QCA ROME chips. The USB device reset happens in btusb_open(), hence firmware loading gets interrupted. Furthermore, this commit stops working after commit ("a0085f2510e8976614ad8f766b209448b385492f Bluetooth: btusb: driver to enable the usb-wakeup feature"). Reset-resume quirk only gets enabled in btusb_suspend() when it's not a wakeup source. If we really want to reset the USB device, we need to do it before btusb_open(). Let's handle it in drivers/usb/core/quirks.c. Cc: stable@vger.kernel.org Cc: Leif Liddy <leif.linux@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Brian Norris <briannorris@chromium.org> Cc: Daniel Drake <drake@endlessm.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-26Bluetooth: Add a new 04ca:3015 QCA_ROME deviceIoan Moldovan
This patch adds the 04ca:3015 (from a QCA9377 board) Bluetooth device to the btusb blacklist and makes the kernel use the btqca module instead of btusb. The patch is necessary because, without it the 04ca:3015 device defaults to using the btusb driver, which makes the WIFI side of the QCA9377 board unusable (obtains 0 MBps in speedtest, when the 04ca:3015 bluetooth is used with an audio headset). /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3015 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Ioan Moldovan <ioan.moldovan1999@gmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-12-13Bluetooth: btusb: Add a Kconfig option to enable USB autosuspend by defaultHans de Goede
On many laptops the btusb device is the only USB device not having USB autosuspend enabled, this causes not only the HCI but also the USB controller to stay awake, together using aprox. 0.4W of power. Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%). The btusb driver already contains code to allow enabling USB autosuspend, but currently leaves it up to the user / userspace to enable it. This means that for most people it will not be enabled, leading to an unnecessarily high power consumption. Since enabling it is not entirely without risk of regressions, this commit adds a Kconfig option so that Linux distributions can choose to enable it by default. This commit also adds a module option so that when distros receive bugs they can easily ask the user to disable it again for easy debugging. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-10-30Bluetooth: btusb: Fix isochronous interface assignmentsMarcel Holtmann
The recent MacBook's with multi-function USB interfaces for HID and Bluetooth operation have the isochronous interface on number 3 instead of number 1. Store the interface number and use it. P: Vendor=05ac ProdID=8290 Rev= 1.40 S: Manufacturer=Broadcom Corp. S: Product=Bluetooth USB Host Controller C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA A: FirstIf#= 2 IfCount= 4 Cls=ff(vend.) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid E: Ad=85(I) Atr=03(Int.) MxPS= 8 Ivl=10ms I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=10ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 3 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 3 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 3 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 3 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 3 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-30Bluetooth: btusb: Update firmware filename for Intel 9x60 and laterJaya P G
The format of Intel Bluetooth firmware for bootloader product is ibt-<hw_variant>-<device_revision_id>.sfi and .ddc. But for the SKU's 9x60, there a 3 variants of FW, which cannot be differentiated just with hw_variant and devision_revision_id. So to pick the appropriate FW file for 9x60 SKU's, it will be differentiated using hw_variant, hw_revision and fw_revision rather than hw_variant and device_revision_id only. Format will be like this: ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi and .ddc Signed-off-by: Jaya P G <jaya.p.g@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-30Bluetooth: Use bt_dev_err and bt_dev_info when possibleMarcel Holtmann
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and bt_dev_info when possible. This allows for controller specific reporting. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-29Bluetooth: btusb: Add new NFA344A entry.Bartosz Chronowski
This change allows proper low power mode entry in suspend. /sys/kernel/debug/usb/devices entry: T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=03 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e09f Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Bartosz Chronowski <ext.bartosz.chronowski@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-10-14Revert "Bluetooth: btusb: Add workaround for Broadcom devices without ↵Hans de Goede
product id" Commit 9834e586fa66 ("Bluetooth: btusb: Add workaround for Broadcom devices without product id") was added to deal with the BT part of the BCM4356A2 on GPD pocket laptops having an usb vid:pid of 0000:0000. After another commit to add support for the BCM UART connected BT ACPI-id BCM2E7E used on the GPD win, it turns out that the BT on the GPD pocket is connected via both USB and UART. Adding support for the BCM2E7E ACPI-id causes it to switch to UART mode. The Windows shipped with the device is using it in UART mode and the presence of the BCM2E7E ACPI-id combined with the all 0 USB vid:pid indicates that the BT part was never meant to be used in USB mode. With the recent patches to use serdev device enumeration / instantiation for UART attached ACPI enumerated BT devices, everything work OOTB in UART mode and the workaround for the all 0 USB vid:pid is no longer needed. This reverts commit 9834e586fa ("Bluetooth: btusb: Add workaround for Broadcom devices without product id"). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-08-16Bluetooth: btusb: driver to enable the usb-wakeup featureSukumar Ghorai
BT-Controller connected as platform non-root-hub device and usb-driver initialize such device with wakeup disabled, Ref. usb_new_device(). At present wakeup-capability get enabled by hid-input device from usb function driver(e.g. BT HID device) at runtime. Again some functional driver does not set usb-wakeup capability(e.g LE HID device implement as HID-over-GATT), and can't wakeup the host on USB. Most of the device operation (such as mass storage) initiated from host (except HID) and USB wakeup aligned with host resume procedure. For BT device, usb-wakeup capability need to enable form btusc driver as a generic solution for multiple profile use case and required for USB remote wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature need to enable/disable with HCI interface up and down. Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com> Signed-off-by: Amit K Bag <amit.k.bag@intel.com> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-08-15Bluetooth: btusb: Add workaround for Broadcom devices without product idMarcel Holtmann
The GPD Pocket is shipping with a BCM2045 USB HCI with its vendor and product information set to 0000:0000 and also has its interface class set to 255 (Vendor Specific Class). Luckily it does advertise usable manufacturer and product strings. T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM2045A0 S: SerialNumber=AC83F30677CB C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Reported-by: Christopher Williamson <home@chrisaw.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-08-08Bluetooth: Add support of 13d3:3494 RTL8723BE deviceDmitry Tunin
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3494 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2017-08-01Bluetooth: btusb: add ID for LiteOn 04ca:3016Brian Norris
Contains a QCA6174A-5 chipset, with USB BT. Let's support loading firmware on it. From usb-devices: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3016 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-07-24Bluetooth: btusb: Fix memory leak in play_deferredJeffy Chen
Currently we are calling usb_submit_urb directly to submit deferred tx urbs after unanchor them. So the usb_giveback_urb_bh would failed to unref it in usb_unanchor_urb and cause memory leak: unreferenced object 0xffffffc0ce0fa400 (size 256): ... backtrace: [<ffffffc00034a9a8>] __save_stack_trace+0x48/0x6c [<ffffffc00034b088>] create_object+0x138/0x254 [<ffffffc0009d5504>] kmemleak_alloc+0x58/0x8c [<ffffffc000345f78>] __kmalloc+0x1d4/0x2a0 [<ffffffc0006765bc>] usb_alloc_urb+0x30/0x60 [<ffffffbffc128598>] alloc_ctrl_urb+0x38/0x120 [btusb] [<ffffffbffc129e7c>] btusb_send_frame+0x64/0xf8 [btusb] Put those urbs in tx_anchor to avoid the leak, and also fix the error handling. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-07-22Bluetooth: Style fix - align block commentsDerek Robson
Fixed alignment of all block comments. Found using checkpatch Signed-off-by: Derek Robson <robsonde@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-07-20Bluetooth: btusb: fix QCA Rome suspend/resumeLeif Liddy
There's been numerous reported instances where BTUSB_QCA_ROME bluetooth controllers stop functioning upon resume from suspend. These devices seem to be losing power during suspend. Patch will detect a status change on resume and perform a reset. Signed-off-by: Leif Liddy <leif.linux@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-07-20Bluetooth: btusb: Add support of all Foxconn (105b) Broadcom devicesDmitry Tunin
There is another device T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=105b ProdID=e066 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=342387DAE35E C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Since we have Cls=ff, we can add all of them. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-15 09:41:29 +0000