summaryrefslogtreecommitdiff
path: root/drivers/bluetooth/btmrvl_sdio.c
AgeCommit message (Collapse)Author
2016-05-02btmrvl: add platform specific wakeup interrupt supportXinming Hu
On some arm-based platforms, we need to configure platform specific parameters by device tree node and also define our node as a child node of parent SDIO host controller. This patch parses these parameters from device tree. It includes calibration data download to firmware, wakeup pin configured to firmware, and soc specific wake up gpio, which will be set as wakeup interrupt pin. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-03-10Bluetooth: btmrvl_sdio: fix firmware activation failureWei-Ning Huang
In some case, the btmrvl_sdio firmware would fail to active within the polling time. Increase the polling interval to 100 msec to fix the issue. Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org> Signed-off-by: Wei-Ning Huang <wnhuang@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-06Bluetooth: btmrvl: don't send data to firmware while processing suspendChin-Ran Lo
Usually when driver sends data to firmware it receives TX_DONE (DN_LD_HOST_INT_STATUS) interrupt from firmware right away. It's also observed that some times the fireware could delay sending DN_LD_HOST_INT_STATUS interrupt. If driver sends data to firmware during suspend processing and the TX_DONE interrupt is delayed, it may come back at wrong time when SDIO host driver is in the middle of suspending. Block any data from stack while suspending. Also skip sending data that are already in driver tx_queue. Don't purge the skb queue on suspend to avoid intermittent music after system resumes from S3. Signed-off-by: Chin-Ran Lo <crlo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-04Bluetooth: btmrvl: fix hung task warning dumpChin-Ran Lo
It's been observed that when bluetooth driver fails to activate the firmware, below hung task warning dump is displayed after 120 seconds. [ 36.461022] Bluetooth: vendor=0x2df, device=0x912e, class=255, fn=2 [ 56.512128] Bluetooth: FW failed to be active in time! [ 56.517264] Bluetooth: Downloading firmware failed! [ 240.252176] INFO: task kworker/3:2:129 blocked for more than 120 seconds. [ 240.258931] Not tainted 3.18.0 #254 [ 240.262972] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 240.270751] kworker/3:2 D ffffffc000205760 0 129 2 0x00000000 [ 240.277825] Workqueue: events request_firmware_work_func [ 240.283134] Call trace: [ 240.285581] [<ffffffc000205760>] __switch_to+0x80/0x8c [ 240.290693] [<ffffffc00088dae0>] __schedule+0x540/0x7b8 [ 240.295921] [<ffffffc00088ddd0>] schedule+0x78/0x84 [ 240.300764] [<ffffffc0006dfd48>] __mmc_claim_host+0xe8/0x1c8 [ 240.306395] [<ffffffc0006edd6c>] sdio_claim_host+0x74/0x84 [ 240.311840] [<ffffffbffc163d08>] 0xffffffbffc163d08 [ 240.316685] [<ffffffbffc165104>] 0xffffffbffc165104 [ 240.321524] [<ffffffbffc130cf8>] mwifiex_dnld_fw+0x98/0x110 [mwifiex] [ 240.327918] [<ffffffbffc12ee88>] mwifiex_remove_card+0x2c4/0x5fc [mwifiex] [ 240.334741] [<ffffffc000596780>] request_firmware_work_func+0x44/0x80 [ 240.341127] [<ffffffc00023b934>] process_one_work+0x2ec/0x50c [ 240.346831] [<ffffffc00023c6a0>] worker_thread+0x350/0x470 [ 240.352272] [<ffffffc0002419bc>] kthread+0xf0/0xfc [ 240.357019] 2 locks held by kworker/3:2/129: [ 240.361248] #0: ("events"){.+.+.+}, at: [<ffffffc00023b840>] process_one_work+0x1f8/0x50c [ 240.369562] #1: ((&fw_work->work)){+.+.+.}, at: [<ffffffc00023b840>] process_one_work+0x1f8/0x50c [ 240.378589] task PC stack pid father [ 240.384501] kworker/1:1 D ffffffc000205760 0 40 2 0x00000000 [ 240.391524] Workqueue: events mtk_atomic_work [ 240.395884] Call trace: [ 240.398317] [<ffffffc000205760>] __switch_to+0x80/0x8c [ 240.403448] [<ffffffc00027279c>] lock_acquire+0x128/0x164 [ 240.408821] kworker/3:2 D ffffffc000205760 0 129 2 0x00000000 [ 240.415867] Workqueue: events request_firmware_work_func [ 240.421138] Call trace: [ 240.423589] [<ffffffc000205760>] __switch_to+0x80/0x8c [ 240.428688] [<ffffffc00088dae0>] __schedule+0x540/0x7b8 [ 240.433886] [<ffffffc00088ddd0>] schedule+0x78/0x84 [ 240.438732] [<ffffffc0006dfd48>] __mmc_claim_host+0xe8/0x1c8 [ 240.444361] [<ffffffc0006edd6c>] sdio_claim_host+0x74/0x84 [ 240.449801] [<ffffffbffc163d08>] 0xffffffbffc163d08 [ 240.454649] [<ffffffbffc165104>] 0xffffffbffc165104 [ 240.459486] [<ffffffbffc130cf8>] mwifiex_dnld_fw+0x98/0x110 [mwifiex] [ 240.465882] [<ffffffbffc12ee88>] mwifiex_remove_card+0x2c4/0x5fc [mwifiex] [ 240.472705] [<ffffffc000596780>] request_firmware_work_func+0x44/0x80 [ 240.479090] [<ffffffc00023b934>] process_one_work+0x2ec/0x50c [ 240.484794] [<ffffffc00023c6a0>] worker_thread+0x350/0x470 [ 240.490231] [<ffffffc0002419bc>] kthread+0xf0/0xfc This patch adds missing sdio_release_host() call so that wlan driver thread can claim sdio host. Fixes: 4863e4cc31d647e1 ("Bluetooth: btmrvl: release sdio bus after firmware is up") Signed-off-by: Chin-Ran Lo <crlo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-19Bluetooth: Use new hci_skb_pkt_* wrappers for driversMarcel Holtmann
The new hci_skb_pkt_* wrappers are mainly intented for drivers to require less knowledge about bt_cb(sbk) handling. So after converting the core packet handling, convert all drivers. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-09-25Bluetooth: btmrvl: Comparison to NULL re-writtenPrasanna Karthik
NOT NULL comparison modified to be readable, reported by checkpatch. Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-22Bluetooth: btmrvl: add sd8997 chipset supportAmitkumar Karwar
This patch adds support for Marvell's new chipset SD8997. Register offsets and supported feature flags are updated. Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-22Bluetooth: btmrvl: remove extra space in castAmitkumar Karwar
Coding style fix, extra spaces are removed to make casting consistent. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-22Bluetooth: btmrvl: fix firmware dump issueNachiket Kukade
First firmware dump attempt from user works fine, but firmware goes into bad state after this. Subsequent attempts fails. As required by the firmware dump implementation, this change writes FW_DUMP_READ_DONE value to dump ctrl register to address this issue. Signed-off-by: Nachiket Kukade <kukaden@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-28Bluetooth: btmrvl: change device pointer passed to dev_coredumpvShengzhen Li
This change ensures we will get driver name as 'btmrvl_sdio' in udev event. Signed-off-by: Shengzhen Li <szli@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-10Bluetooth: btmrvl: release sdio bus after firmware is upAniket Nagarnaik
We will not release sdio bus until firmware is completely downloaded and becomes ready. Our 8887 A2 chip can have separate firmware images for WLAN and bluetooth. This patch fixes an issue observed when both drivers simultaneously try to download respective firmwares. Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-13Bluetooth: btmrvl: fix compilation warningXinming Hu
This patch fixes a compile warnning "dump_num maybe used uninitialized in this function". Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-01-06bluetooth: btmrvl: increase the priority of firmware download messageAmitkumar Karwar
When driver is loaded, it is important to know if FW was already active or it is freshly downloaded. This patch increases the priority of the message. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-01-06Bluetooth: btmrvl: add surprise_removed flagAmitkumar Karwar
This flag will be set in unload path to make sure that we skip sending further commands, ignore interrupts and stop main thread when unload starts. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-12-03Bluetooth: btmrvl add firmware dump supportXinming Hu
This patch adds firmware dump support for marvell bluetooth chipset. Currently only SD8897 is supported. This is implemented based on dev_coredump, a new mechnism introduced in kernel 3.18rc3 Firmware dump can be trigger by echo 1 > /sys/kernel/debug/bluetooth/hci*/config/fw_dump and when the dump operation is completed, data can be read by cat /sys/class/devcoredump/devcd*/data We have prepared following script to divide fw memory dump data into multiple files based on memory type. [root]# cat btmrvl_split_dump_data.sh #!/bin/bash # usage: ./btmrvl_split_dump_data.sh dump_data fw_dump_data=$1 mem_type="ITCM DTCM SQRAM APU CIU ICU MAC EXT7 EXT8 EXT9 EXT10 EXT11 EXT12 EXT13 EXTLAST" for name in ${mem_type[@]} do sed -n "/Start dump $name/,/End dump/p" $fw_dump_data > tmp.$name.log if [ ! -s tmp.$name.log ] then rm -rf tmp.$name.log else # Remove the describle info "Start dump" and "End dump" sed '1d' tmp.$name.log | sed '$d' > /data/$name.log if [ -s /data/$name.log ] then echo "generate /data/$name.log" else sed '1d' tmp.$name.log | sed '$d' > /var/$name.log echo "generate /var/$name.log" fi rm -rf tmp.$name.log fi done Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-12-03Bluetooth: btmrvl: remove extra newline characterAmitkumar Karwar
BT_INFO/BT_DBG etc. already takes care of adding a newline An extra newline character inside message is removed in this patch. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-30Bluetooth: btmrvl: support Marvell Bluetooth device SD8887Xinming Hu
This patch adds driver support for marvell SD8887 chip. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Kevin Gan <ganhy@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-09-30Bluetooth: btmrvl: rename definitions from 88xx to 8897Amitkumar Karwar
Register offsets are different for SD8897 and newer chip SD8887. We can not have common btmrvl_sdio_card_reg map for them. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-07-15Bluetooth: btmrvl: avoid sending data to firmware after hs_activatedChin-Ran Lo
We should suspend hci device and purge remaining data in tx queue before enabling host sleep in firmware. If any data is sent to firmware after host sleep is activated, firmware may end up sending a TX_DONE interrupt to driver. If this interrupt gets delivered to host while the SDIO host controller is suspending, it may crash the system. Conversely, in resume handler, we should resume hci device after host sleep is de-activated. Signed-off-by: Chin-Ran Lo <crlo@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-07-03Bluetooth: btmrvl: indicate pscan scheduling instant in a debug eventBing Zhao
A vendor specific command is sent to firmware during initialization to enable this feature. This command is for SD8897 only. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-03-28Bluetooth: btmrvl: implement read-to-clear for SD8897 interruptsBing Zhao
For SD8897, CMD52 write_to_clear may have missing interrupts under certain corner case condition. Use CMD53 read-to-clear to fix the problem. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-03-28Bluetooth: btmrvl: separate write-to-clear function from interrupt handlerBing Zhao
This patch improves readability and makes future changes easier. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-12-04Bluetooth: btmrvl: use cal-data from device-tree instead of conf fileBing Zhao
Some ARM versions of Chromebook need to download a new calibration data from host driver to firmware. They do have EEPROM but still need a piece of new calibration data in test mode. The cal-data is platform dependent. It's simpler and more feasible to use device tree based cal-data instead of configuration file based cal-data. This patch remove configuration file based cal-data downloading and replace it using cal-data from device tree. When CONFIG_OF is not selected, or the specific property is not present in the device tree, the calibration downloading will not happen. Cc: Mike Frysinger <vapier@chromium.org> Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-11Bluetooth: Provide hdev parameter to hci_recv_frame() driver callbackMarcel Holtmann
To avoid casting skb->dev into hdev, just let the drivers provide the hdev directly when calling hci_recv_frame() function. This patch also fixes up all drivers to provide the hdev. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-02Bluetooth: btmrvl: add calibration data download supportAmitkumar Karwar
A text file containing calibration data in hex format can be provided at following path: /lib/firmware/mrvl/sd8797_caldata.conf The data will be downloaded to firmware during initialization. Reviewed-by: Mike Frysinger <vapier@chromium.org> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-10-02Bluetooth: btmrvl: add setup handlerAmitkumar Karwar
Move initialization code to hdev's setup handler. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-08-21Bluetooth: use DIV_ROUND_UP in suitable places in btmrvl_sdioAndy Shevchenko
There are two places where DIV_ROUND_UP may be used. It makes code a bit clearer. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-06-13Bluetooth: btmrvl: fix error return code in btmrvl_sdio_card_to_host()Wei Yongjun
Fix to return -ENOMEM in the skb alloc error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12Bluetooth: btmrvl: support Marvell Bluetooth device SD8897Bing Zhao
The register offsets have been changed in SD8897 and newer chips. Define a new btmrvl_sdio_card_reg map for SD88xx. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-04-23Bluetooth: btmrvl: report error if verify_fw_download times outAndreas Fenkart
FW does the synchronization of the different modules during init. It will report different modules, that it is ready at different times. The fw download 'winner' will be reported fw ready first. Without this patch, btmrvl was already continuing before the FW told it too. Probably on behalf of the 'winner' which then never sees FW ready and times out. Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-23Bluetooth: btmrvl: release lock while waiting for fw download completeAndreas Fenkart
If not winner, driver must release the sdio host lock, so the fw download can progress. While holding the lock fw download is stalled and the following error is produced: [ 235.746015] Bluetooth: FW failed to be active in time! [ 235.752799] Bluetooth: Downloading firmware failed! Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-18Bluetooth: remove unneeded var initialization in btmrvlGustavo Padovan
There is no need to init ret to zero in btmrvl_sdio_download_fw(). Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-03-15bluetooth: btmrvl_sdio: look for sd8688 firmware in proper locationLubomir Rintel
The firmware images are shared with libertas_sdio WiFi chip and used to be in libertas/ subtree in linux-firmware. As btmrvl_sdio used to look into the linux-firmware root, it ended up being unsuccessful. Since the firmware files are not specific to the libertas hardware, they're being moved into mrvl/ now. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-10-11Bluetooth: btmrv: Use %*ph specifier instead of print_hex_dump_bytesAndrei Emeltchenko
Use standard print specifier and remove print_hex_dump_bytes call. Makes output more sensible: ... [18809.401218] 00000000: 0b 00 00 fe 5b fc 01 f2 00 00 00 ....[...... ... would be changed to ... [18809.401218] Bluetooth: hex: 0b 00 00 fe 5b fc 01 f2 00 00 00 ... Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-09-28Bluetooth: btmrvl: Fix skb buffer overflowAndrei Emeltchenko
Add extra check to avoid skb buffer overflow. Fixes crash below: [ 101.030427] ------------[ cut here ]------------ [ 101.030459] kernel BUG at net/core/skbuff.c:127! [ 101.030486] invalid opcode: 0000 [#1] SMP ... [ 101.030806] Pid: 2010, comm: btmrvl_main_ser Not tainted 3.5.0+ #80 Laptop [ 101.030859] EIP: 0060:[<c14f2ba9>] EFLAGS: 00010282 CPU: 0 [ 101.030894] EIP is at skb_put+0x99/0xa0 [ 101.030919] EAX: 00000080 EBX: f129380b ECX: ef923540 EDX: 00000001 [ 101.030956] ESI: f00a4000 EDI: 00001003 EBP: ed4a5efc ESP: ed4a5ecc [ 101.030992] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 101.031024] CR0: 8005003b CR2: 08fca014 CR3: 30960000 CR4: 000407f0 [ 101.031062] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000 [ 101.031100] DR6: ffff0ff0 DR7: 00000400 [ 101.031125] Process btmrvl_main_ser (pid: 2010, ti=ed4a4000 task=ef923540 task.ti=ed4a4000) [ 101.031174] Stack: [ 101.031188] c18126f8 c1651938 f853f8d2 00001003 00001003 f1292800 f1292808 f129380b [ 101.031250] f1292940 f00a4000 eddb1280 efc0f9c0 ed4a5f44 f853f8d2 00000040 00000000 [ 101.031312] ef923540 c15ee096 ef923540 eddb12d4 00000004 f00a4000 00000040 00000000 [ 101.031376] Call Trace: [ 101.031396] [<f853f8d2>] ? btmrvl_sdio_process_int_status+0x272/0x3d0 [btmrvl_sdio] [ 101.031444] [<f853f8d2>] btmrvl_sdio_process_int_status+0x272/0x3d0 [btmrvl_sdio] [ 101.031488] [<c15ee096>] ? _raw_spin_unlock_irqrestore+0x36/0x70 [ 101.031526] [<f85a46e4>] btmrvl_service_main_thread+0x244/0x300 [btmrvl] [ 101.031568] [<f853fb50>] ? btmrvl_sdio_poll_card_status.isra.6.constprop.7+0x90/0x90 [btmrvl_sdio] [ 101.031619] [<c107eda0>] ? try_to_wake_up+0x270/0x270 [ 101.031648] [<f85a44a0>] ? btmrvl_process_event+0x3b0/0x3b0 [btmrvl] [ 101.031686] [<c106d19d>] kthread+0x7d/0x90 [ 101.031713] [<c106d120>] ? flush_kthread_work+0x150/0x150 [ 101.031745] [<c15f5a82>] kernel_thread_helper+0x6/0x10 ... [ 101.032008] EIP: [<c14f2ba9>] skb_put+0x99/0xa0 SS:ESP 0068:ed4a5ecc [ 101.056125] ---[ end trace a0bd01d1a9a796c8 ]--- Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-09-28Bluetooth: btmrvl: Use DIV_ROUND_UP macroAndrei Emeltchenko
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) / (d)) Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-09-28Bluetooth: btmrvl: Correct num_block nameAndrei Emeltchenko
Make code readable by correcting name from buf_block_len to num_blocks since it represent number of blocks; NOT a length of a block buffer. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-09-08Bluetooth: btmrvl: remove pointless conditional before kfree_skb()Wei Yongjun
Remove pointless conditional before kfree_skb(). Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: Use devm_kzalloc in btmrvl_sdio.c fileSachin Kamat
devm_kzalloc() eliminates the need to free memory explicitly thereby saving some cleanup code. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-09Bluetooth: btmrvl: trivial style fixesAndrei Emeltchenko
Patch shortens locals scope and adds missing braces. This is a diff between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do not send vendor events to bluetooth stack". Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-26Merge branch 'for-upstream' of ↵Gustavo Padovan
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
2012-06-19Bluetooth: btmrvl: Do not send vendor events to bluetooth stackAndrei Emeltchenko
Vendor-specific events shall be processed in driver and not sent to bluetooth stack where they screw up HCI command countings. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-05Bluetooth: btmrvl: add SD8787 Bluetooth AMP device IDBing Zhao
SD8787 SDIO function 3 (device ID 0x911B) is for Bluetooth AMP. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-05-09Bluetooth: btmrvl: add support for SDIO suspend/resume callbacksAmitkumar Karwar
Host sleep is activated using already configured host sleep parameters in suspend handler and it is cancelled in resume handler. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09Bluetooth: btmrvl: configure default host sleep parametersAmitkumar Karwar
Currently debugfs commands "hscfgcmd" and "gpiogap" are provided for host sleep configuration. But if user doesn't configure host sleep parameters using these commands, host sleep activation is failed during suspend (support for suspend and resume handlers is added in next patch). Default host sleep configuration is done during driver initialisation in this patch. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09Bluetooth: btmrvl_sdio: remove pointless conditional before release_firmware()Jesper Juhl
release_firmware() deals gracefullt with NULL pointers so there's no reason to test for one prior to calling the function. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2011-12-09Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2011-11-21Bluetooth: btmrvl: support Marvell Bluetooth device SD8797Bing Zhao
The SD8797 firmware image is shared with mwifiex driver. Whoever gets loaded first will be responsible for firmware downloading. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-10-31bluetooth: add module.h to drivers/bluetooth files as required.Paul Gortmaker
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-05btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'Paul Bolle
It should be 'btmrvl_sdio_sd8688', of course. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-01 11:52:42 +0000