summaryrefslogtreecommitdiff
path: root/drivers/bluetooth/btbcm.c
AgeCommit message (Collapse)Author
2019-11-22Bluetooth: btbcm: Use the BDADDR_PROPERTY quirkAndre Heider
Some devices ship with the controller default address, like the Orange Pi 3 (BCM4345C5). Allow the bootloader to set a valid address through the device tree. Signed-off-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-11-21Bluetooth: btbcm: Add entry for BCM4335A0 UART bluetoothMohammad Rasim
This patch adds the device ID for the BCM4335A0 module (part of the AMPAK AP6335 WIFI/Bluetooth combo) hciconfig output: ``` hci1: Type: Primary Bus: UART BD Address: 43:35:B0:07:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING RX bytes:5079 acl:0 sco:0 events:567 errors:0 TX bytes:69065 acl:0 sco:0 commands:567 errors:0 Features: 0xbf 0xfe 0xcf 0xff 0xdf 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'alarm' Class: 0x000000 Service Classes: Unspecified Device Class: Miscellaneous, HCI Version: 4.0 (0x6) Revision: 0x161 LMP Version: 4.0 (0x6) Subversion: 0x4106 Manufacturer: Broadcom Corporation (15) ``` Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-11-19Bluetooth: btbcm: Add entry for BCM4334B0 UART BluetoothStephan Gerhold
Add the device ID for the WiFi/BT/FM combo chip BCM4334 (rev B0). The chip seems to use 43:34:b0:00:00:00 as default address, so add it to the list of default addresses and leave it up to the user to configure a valid one. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-09-05bluetooth: bcm: Add support for loading firmware for BCM4345C5Ondrej Jirman
Detect BCM4345C5 and load a corresponding firmware file. Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06Bluetooth: btbcm: Add entry for BCM4359C0 UART bluetoothNeil Armstrong
The BCM4359C0 BT/Wi-Fi compo chip needs an entry to be discovered by the btbcm driver. Tested using an AP6398S module from Ampak. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 156Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 59 temple place suite 330 boston ma 02111 1307 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1334 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-05Bluetooth: btbcm: Add default address for BCM2076B1Stephan Gerhold
BCM2076B1 appears to use 20:76:A0:00:56:79 as default address. This address is used by at least 5 devices with the AMPAK AP6476 module and is also suspicious because it starts with the chip name 2076 (followed by a different revision A0 for some reason). Add it to the list of default addresses and leave it up to the user to configure a valid one. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-04-23Bluetooth: btbcm: Add entry for BCM2076B1 UART BluetoothStephan Gerhold
Add the device ID for the BT/FM/GPS combo chip BCM2076 (rev B1) used in the AMPAK AP6476 WiFi/BT/FM/GPS module. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-04-23Bluetooth: btbcm: Add default address for BCM43341BFerry Toth
The BCM43341B has the default MAC address 43:34:1B:00:1F:AC if none is given. This address was found when enabling Bluetooth on multiple Intel Edison modules. It also contains the sequence 43341B, the name the chip identifies itself as. Using the same BD_ADDR is problematic when having multiple Intel Edison modules in each others range. The default address also has the LAA (locally administered address) bit set which prevents a BNEP device from being created, needed for BT tethering. Add this to the list of black listed default MAC addresses and let the user configure a valid one using f.i. `btmgmt -i hci0 public-addr xx:xx:xx:xx:xx:xx` Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ferry Toth <ftoth@exalondelft.nl> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-12-19Bluetooth: btbcm: Add entry for BCM4329B1 UART bluetoothPaweł Chmiel
This patch adds the device ID for the BCM 4329 combo module used in the Samsung Aries based phones (Galaxy S and it's variants). ``` [ 11.508980] Bluetooth: hci0: BCM: chip id 41 [ 11.518975] Bluetooth: hci0: BCM: features 0x04 [ 11.550132] Bluetooth: hci0: BCM4329B1 [ 11.557046] Bluetooth: hci0: BCM4329B1 (002.002.023) build 0000 [ 13.737071] Bluetooth: hci0: BCM4329B1 (002.002.023) build 0744 ``` Output from hciconfig ``` hci0: Type: Primary Bus: UART BD Address: 43:29:B1:55:00:00 ACL MTU: 1021:6 SCO MTU: 64:1 UP RUNNING RX bytes:1675 acl:0 sco:0 events:145 errors:0 TX bytes:20426 acl:0 sco:0 commands:146 errors:0 Features: 0xbf 0xfe 0x8f 0xfe 0x9b 0xff 0x79 0x83 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'aries' Class: 0x000000 Service Classes: Unspecified Device Class: Miscellaneous, HCI Version: 2.1 (0x4) Revision: 0x2e8 LMP Version: 2.1 (0x4) Subversion: 0x4217 Manufacturer: Broadcom Corporation (15) ``` Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-12-19Bluetooth: btbcm: Add default address for BCM43430A0Chen-Yu Tsai
The BCM43430A0 has the default MAC address 43:43:A0:12:1F:AC if none is given. This address was found when enabling Bluetooth on a bunch of boards with the AMPAK AP6210 module, all sharing the same address. It also contains the sequence 4343A0, which is suspicious as that is also the name the chip identifies itself as. Add this to the list of default MAC addresses and leave it to the user to configure a valid one. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-12-19Bluetooth: hci_bcm: Add BCM20702A1 variantMaxime Ripard
The BCM20702A1 chip is a single-chip Bluetooth 4.0 controller and transceiver. It is found in the AMPAK AP6210 WiFi+BT package. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27Bluetooth: btbcm: Add entry for BCM4335C0 UART bluetoothChristian Hewitt
This patch adds the device ID for the AMPAK AP6335 combo module used in the 1st generation WeTek Hub Android/LibreELEC HTPC box. The WiFI chip identifies itself as BCM4339, while Bluetooth identifies itself as BCM4335 (rev C0): ``` [ 4.864248] Bluetooth: hci0: BCM: chip id 86 [ 4.866388] Bluetooth: hci0: BCM: features 0x2f [ 4.889317] Bluetooth: hci0: BCM4335C0 [ 4.889332] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0000 [ 9.778383] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0268 ``` Output from hciconfig: ``` hci0: Type: Primary Bus: UART BD Address: 43:39:00:00:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING RX bytes:7567 acl:234 sco:0 events:386 errors:0 TX bytes:53844 acl:77 sco:0 commands:304 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'HUB' Class: 0x0c0000 Service Classes: Rendering, Capturing Device Class: Miscellaneous, HCI Version: 4.0 (0x6) Revision: 0x10c LMP Version: 4.0 (0x6) Subversion: 0x6109 Manufacturer: Broadcom Corporation (15) ``` Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: btbcm: btbcm_initialize(): Initialize hw_name to "BCM"Hans de Goede
Initialize hw_name to "BCM", this avoids the need for a number of NULL checks on hw_name later. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: btbcm: Remove duplicate code from btbcm_setup_patchram()Hans de Goede
btbcm_setup_patchram() starts with initializing the controller (and getting the firmware filename) and then after loading the firmware, does a re-init. This almost entirely duplicates the code in btbcm_initialize(), use that function instead. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: btbcm: Allow using btbcm_initialize() for reinitHans de Goede
btbcm_finalize() does a re-init of the controller, which is almost the same as the initial init. Modify btbcm_initialize() so that it can be used for this re-init and modify btbcm_finalize() to use it. As an added bonus this also makes the dev_info from btbcm_finalize() use the proper hw_name instead of always printing "BCM". Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: btbcm: Make btbcm_initialize() also work for USB connected devicesHans de Goede
Make btbcm_initialize() also work for USB connected device, btbcm_initialize() and btbcm_setup_patchram() are quite similar, this is a preparation patch for making btbcm_setup_patchram() use btbcm_initialize() to remove the code duplication. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: btbcm: Factor out common code to determine subversionHans de Goede
We are using the same loop in both the UART and USB bus cases, refactor things a bit to share the loop. This is mostly meant to improve readability. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18Bluetooth: btbcm: Stop using upper nibble of rev to chose between uart/USB pathsHans de Goede
btbcm_setup_patchram() was using the upper nibble of the revision code to determine if we are dealing with an uart or USB connected bcm-bt device, but just as btbcm_initialize() has started accepting 1 and 2 as uart connected devices, I've now encountered an USB connected device (0a5c:216c) which has 0 in the upper nibble. So it seems that the upper nibble is not really a reliable indicator of the bus type. Instead check hdev->bus which does give us a reliable indication. This fixes the patchram code trying to load the patchram by the fallback BCM.hcd filename, now it correctly requests BCM43142A0-0a5c-216c.hcd. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-01-18Bluetooth: btbcm: Add entry for BCM4343A0 UART bluetoothJörg Krause
This patch adds the device ID for the bluetooth chip used in the AMPAK AP6212 WiFi+Bluetooth module. The AP6212 is used on several BananaPi boards, e.g. M2-Ultra. The AP6212 is a combo module, where the WiFi chip is identified as BCM43430A0 whereas the Bluetooth chip identifies itself as 4343A0. Note, the missing '0' before the 'A0'. The AP6212 needs a firmware blob. Loading the provided firmware file from the BananaPi vendor, the adapter name is printed as 'BCM4343A0 26MHz AP6212_CL1-0061': ''' hci0: Type: Primary Bus: UART BD Address: 43:43:A0:12:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING RX bytes:3076 acl:0 sco:0 events:278 errors:0 TX bytes:39726 acl:0 sco:0 commands:279 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'BCM4343A0 26MHz AP6212_CL1-0061' Class: 0x000000 Service Classes: Unspecified Device Class: Miscellaneous, HCI Version: 4.1 (0x7) Revision: 0xf2 LMP Version: 4.1 (0x7) Subversion: 0x2122 Manufacturer: Broadcom Corporation (15) ''' Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-10-30Bluetooth: Use bt_dev_err and bt_dev_info when possibleMarcel Holtmann
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and bt_dev_info when possible. This allows for controller specific reporting. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-14Bluetooth: btbcm: Add entry for BCM4356A2 UART bluetoothHans de Goede
This patch adds the device ID for the bluetooth chip used in the Broadcom BCM4356 PCI-E WiFi / UART BT chip. Successfully tested using Firmware version 0273 The upper nibble of the rev field is 2 on this device, so this commit also adds handling of 2 to the switch-case done on the upper nibble. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-10-10Bluetooth: btbcm: Add support for MINIX Z83-4 based devicesIan W MORRISON
The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip for wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4 with BCM4345 rev C0 firmware. This patch defines the firmware subversion. Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-08-17Bluetooth: btbcm: Consolidate the controller information commandsMarcel Holtmann
The commands that read the basic vendor information about the Broadcom controller are duplicated for UART and USB devices. Combine them into a single function to reduce the code complexity. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-06-29Bluetooth: btbcm: Add entry for BCM43430 UART bluetoothIan Molton
This patch adds the device ID for the bluetooth chip used in the Broadcom BCM43430 SDIO WiFi / UART BT chip. Successfully tested using Firmware version 0x0182 Signed-off-by: Ian Molton <ian@mnementh.co.uk> Reported-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-06-12Bluetooth: btbcm: Read controller features during configurationMarcel Holtmann
Read the Broadcom specific controller features during configuration and print them for informational purposes. < HCI Command: Broadcom Read Controller Features (0x3f|0x006e) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Broadcom Read Controller Features (0x3f|0x006e) ncmd 1 Status: Success (0x00) Features: 0x07 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Multi-AV transport bandwidth reducer WBS SBC FW LC-PLC Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
2017-02-16Bluetooth: btbcm: Add a delay for module resetWen-chien Jesse Sung
Some btbcm devices require more time to complete its reset process. They won't reply any hci command until reset is done. [ 17.218554] Bluetooth: hci0 command 0x1001 tx timeout [ 25.214999] Bluetooth: hci0: BCM: Reading local version info failed (-110) Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-02-23Bluetooth: btbcm: Fix handling of firmware not foundPetri Gynther
If the call to request_firmware() fails in btbcm_setup_patchram(), the BCM chip will be operating with its default firmware. In this case, btbcm_setup_patchram() should not return immediately but instead should skip to btbcm_check_bdaddr() and quirk setup. Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21Bluetooth: btbcm: Read USB product information for Apple devicesMarcel Holtmann
For the Apple Bluetooth devices, read the USB product information and print them. This allows for easy mapping of chip and USB details. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btbcm: Fix firmware version number calculationMarcel Holtmann
The calculation for the firmware version number is off by one bit. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-07Bluetooth: btbcm: Read the local name in setup stageMarcel Holtmann
The Broadcom Bluetooth controllers have the chip name included in the ROM firmware or later in the patchram firmware. For debugging purposes read the local name and print it out. This is only done during setup stage and only once before loading the firmware and once after loading the firmware. For the Broadcom based controllers from Apple, the name is only read once after determining the chip id. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-05Bluetooth: btbcm: Send HCI Reset before sending Apple specific commandsMarcel Holtmann
The commit 7bee8b08c428 allows the Read Verbose Config Info to fail gracefully and not cause the controller setup to abort. It seems the reason that command failed in the first place was the missing HCI Reset to bring the controller in full Bluetooth mode. Apple Bluetooth controllers start out in HID mode and when in that mode the Read Verbose Config Info command is not allowed. Sending HCI Reset switches the controller into full HCI mode. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-07-30Bluetooth: btbcm: Add BCM4330B1 UART deviceFrederic Danis
Add "waiting for configuration" address. Add lmp_subver and firmware name for BCM4330B1 controller. Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-14Bluetooth: btbcm: allow btbcm_read_verbose_config to fail on AppleChris Mason
Commit 1c8ba6d013 moved around the setup code for broadcomm chips, and also added btbcm_read_verbose_config() to read extra information about the hardware. It's returning errors on some macbooks: Bluetooth: hci0: BCM: Read verbose config info failed (-16) Which makes us error out of the setup function. Since this probe isn't critical to operate the chip, this patch just changes things to carry on when it fails. Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org # v4.1
2015-06-17Bluetooth: btbcm: Support the BCM4354 Bluetooth UART deviceIlya Faenson
Support the BCM4354 chip and introduce vendor specific command parameter definitions. Signed-off-by: Ilya Faenson <ifaenson@broadcom.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-06-06Bluetooth: btbcm: Add helper functions for UART setupFrederic Danis
Firmware loading may reset the controller UART speed and needs to set host UART speed back to init speed. UART drivers setup is split in 3 parts: - btbcm_initialize() resets the controller and returns the firmware name based on controller revision and sub_version. - btbtcm_patchram() (already existing and public), which takes the firmware name as parameter, requests the firmware and loads it to the controller. - btbcm_finalize() which resets the controller, reads local version and checks if the controller address is a default one or not. Remove firmware name retrieval for UART controllers from btbcm_setup_patchram(). Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-06-06Bluetooth: btbcm: Add BCM4324B3 UART deviceFrederic Danis
Add "waiting for configuration" address. Add lmp_subver and firmware name for BCM4324B3 controller. Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-06-06Bluetooth: btbcm: Move request/release_firmware()Frederic Danis
Move request/release_firmware() out of btbcm_patchram(). This allows a better error management, if request_firmware() returns an error then the controller will be used without firmware loading and 0 is returned. This will imply to change btbcm_patchram() to accept a firmware instead of firmware name. Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-15Bluetooth: btbcm: Fix calls to __hci_cmd_sync()Frederic Danis
Remove test of command reply status as it is already performed by __hci_cmd_sync(). __hci_cmd_sync_ev() function already returns an error if it got a non-zero status either through a Command Complete or a Command Status event. For both of these events the status is collected up in the event handlers called by hci_event_packet() and then passed as the second parameter to req_complete_skb(). The req_complete_skb() callback in turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores the status in hdev->req_result. The hdev->req_result is then further converted through bt_to_errno() back in __hci_cmd_sync_ev(). Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-04-30Bluetooth: btbcm: Export patchram download as separate functionMarcel Holtmann
This isolates the Broadcom patchram download procedure as separate function so that it can be easily used from USB and UART based drivers. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-07Bluetooth: btbcm: Add firmware table for UART based devicesMarcel Holtmann
The Broadcom UART based devices seem to use a little bit different firmare naming prefix. So add a separate table for these devices. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-07Bluetooth: btusb: Move Broadcom quirk setting into support moduleMarcel Holtmann
The quirks for Broadcom devices can be set from the setup function and to keep the code simple, just move them into Broadcom support module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-07Bluetooth: btbcm: Add support for Broadcom controller setupMarcel Holtmann
To unify the controller setup of Broadcom devices between USB and UART transport, add the patchram download support into the Broadcom module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-07Bluetooth: btbcm: Introduce generic Broadcom Bluetooth supportMarcel Holtmann
The majority of Broadcom Bluetooth vendor commands are shared between USB and UART transports. This creates a separate module that eventually will hold all Broadcom specific commands, but for now just start with the commands to change the Bluetooth public address and check for the default address. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-01 23:33:52 +0000