| Age | Commit message (Collapse) | Author |
|---|
|
Since sTec s1120 devices support 64-bit DMA it is not necessary
to request data buffer bouncing. Hence remove the
blk_queue_bounce_limit() call.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus
Pull xen-blkback fix from Konrad:
"[...] A bug-fix when shutting down xen block backend driver with
multiple queues and the driver not clearing all of them."
|
|
struct call_single_data is used in IPIs to transfer information between
CPUs. Its size is bigger than sizeof(unsigned long) and less than
cache line size. Currently it is not allocated with any explicit alignment
requirements. This makes it possible for allocated call_single_data to
cross two cache lines, which results in double the number of the cache lines
that need to be transferred among CPUs.
This can be fixed by requiring call_single_data to be aligned with the
size of call_single_data. Currently the size of call_single_data is the
power of 2. If we add new fields to call_single_data, we may need to
add padding to make sure the size of new definition is the power of 2
as well.
Fortunately, this is enforced by GCC, which will report bad sizes.
To set alignment requirements of call_single_data to the size of
call_single_data, a struct definition and a typedef is used.
To test the effect of the patch, I used the vm-scalability multiple
thread swap test case (swap-w-seq-mt). The test will create multiple
threads and each thread will eat memory until all RAM and part of swap
is used, so that huge number of IPIs are triggered when unmapping
memory. In the test, the throughput of memory writing improves ~5%
compared with misaligned call_single_data, because of faster IPIs.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Huang, Ying <ying.huang@intel.com>
[ Add call_single_data_t and align with size of call_single_data. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/87bmnqd6lz.fsf@yhuang-mobile.sh.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Make this const as is is only passed as an argument to the
function device_create_file and device_remove_file and the corresponding
arguments are of type const.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We already have this pointer, no need to use to_nullb_device()
again.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 2984c86(nullb: factor disk parameters) has a typo. The
nullb_device allocation/free is done outside of null_add_dev. The commit
accidentally frees the nullb_device in error code path.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Linux 4.13-rc7
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes two obvious bugs in virtio pci"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: fix cpu affinity support
virtio_blk: fix incorrect message when disk is resized
|
|
The SKD_ID_INCR flag in skd_request_context.id duplicates information
that is already available otherwise, e.g. through the block layer
request state and through skd_request_context.state. Hence remove
the code that manipulates this flag and also the flag itself.
Since skd_isr_completion_posted() only uses the lower bits of
skd_request_context.id as hardware tag, this patch does not change
the behavior of the skd driver. I'm referring to the following code:
tag = req_id & SKD_ID_SLOT_AND_TABLE_MASK;
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Although it is easy to see that skdev->disk != NULL if skdev->queue
!= NULL, add a test for skdev->disk to avoid that smatch reports the
following warning:
drivers/block/skd_main.c:3080 skd_free_disk()
error: we previously assumed 'disk' could be null (see line 3074)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It is not worth to keep the debug statements in skd_end_request().
Without debug statements that function only consists of two
statements. Hence inline skd_end_request().
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The latter name follows more closely the function names used in
other blk-mq drivers.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Dan reported this:
The patch 2984c8684f96: "nullb: factor disk parameters" from Aug 14,
2017, leads to the following Smatch complaint:
drivers/block/null_blk.c:1759 null_init_tag_set()
error: we previously assumed 'nullb' could be null (see line
1750)
1755 set->cmd_size = sizeof(struct nullb_cmd);
1756 set->flags = BLK_MQ_F_SHOULD_MERGE;
1757 set->driver_data = NULL;
1758
1759 if (nullb->dev->blocking)
^^^^^^^^^^^^^^^^^^^^
And an unchecked dereference.
nullb could be NULL here.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In xen_blkif_disconnect, before checking inflight I/O, following code
stops the blkback thread,
if (ring->xenblkd) {
kthread_stop(ring->xenblkd);
wake_up(&ring->shutdown_wq);
}
If there is inflight I/O in any non-last queue, blkback returns -EBUSY
directly, and above code would not be called to stop thread of remaining
queue and processs them. When removing vbd device with lots of disk I/O
load, some queues with inflight I/O still have blkback thread running even
though the corresponding vbd device or guest is gone.
And this could cause some problems, for example, if the backend device type
is file, some loop devices and blkback thread always lingers there forever
after guest is destroyed, and this causes failure of umounting repositories
unless rebooting the dom0.
This patch allows thread of every queue has the chance to get stopped.
Otherwise, only thread of queue previous to(including) first busy one get
stopped, blkthread of remaining queue will still run. So stop all threads
properly and return -EBUSY if any queue has inflight I/O.
Signed-off-by: Annie Li <annie.li@oracle.com>
Reviewed-by: Herbert van den Bergh <herbert.van.den.bergh@oracle.com>
Reviewed-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Reviewed-by: Adnan Misherfi <adnan.misherfi@oracle.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Update to a working one, the fusionio address hasn't been valid
in 4 years.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The message printed on disk resize is incorrect. The following is
printed when resizing to 2 GiB:
$ truncate -s 1G test.img
$ qemu -device virtio-blk-pci,logical_block_size=4096,...
(qemu) block_resize drive1 2G
virtio_blk virtio0: new size: 4194304 4096-byte logical blocks (17.2 GB/16.0 GiB)
The virtio_blk capacity config field is in 512-byte sector units
regardless of logical_block_size as per the VIRTIO specification.
Therefore the message should read:
virtio_blk virtio0: new size: 524288 4096-byte logical blocks (2.15 GB/2.0 GiB)
Note that this only affects the printed message. Thankfully the actual
block device has the correct size because the block layer expects
capacity in sectors.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The hpsa driver now has support for all boards the cciss driver
used to support, so this patch removes the cciss driver and
make hpsa an alias to cciss.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Lguest seems to be rather unused these days. It has seen only patches
ensuring it still builds the last two years and its official state is
"Odd Fixes".
Remove it in order to be able to clean up the paravirt code.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: boris.ostrovsky@oracle.com
Cc: lguest@lists.ozlabs.org
Cc: rusty@rustcorp.com.au
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20170816173157.8633-3-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There's some stuff still up in the air, let's not get stuck with a
subpar ABI. I'll follow up with something better for 4.14.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since MSI support on some motherboards is unreliable, change the
default interrupt mode from MSI to MSI-X. This patch avoids that
the following message appears sporadially in the kernel logs of
my test setup:
do_IRQ: 3.193 No irq handler for vector
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Avoid that normal request completion and the timeout handler can
run concurrently by calling blk_mq_complete_request() instead of
blk_mq_end_request() from skd_end_request(). Avoid that the block
layer can reuse a request while the firmware is still processing
it. Convert skd_softirq_done() to blk-mq. Pass the pointer to
skd_softirq_done() to the block layer core through
blk_mq_ops.complete instead of by calling blk_queue_softirq_done().
Pass the pointer to skd_timed_out() to the block layer core
through blk_mq_ops.timeout instead of by calling
blk_queue_timed_out(). The timeout handler has been tested as
follows:
echo 1 > /sys/block/skd0/io-timeout-fail &&
(cd /sys/kernel/debug/fail_io_timeout &&
echo 100 > probability &&
echo N > task-filter &&
echo 1 > times)
Fixes: commit a74d5b76fab9 ("skd: Switch to block layer timeout mechanism")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch does not change any functionality but makes the skd
driver code more similar to that of other blk-mq kernel drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch removes one debug statement but otherwise does not change
any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Sometime disk could have tracks broken and data there is inaccessable,
but data in other parts can be accessed in normal way. MD RAID supports
such disks. But we don't have a good way to test it, because we can't
control which part of a physical disk is bad. For a virtual disk, this
can be easily controlled.
This patch adds a new 'badblock' attribute. Configure it in this way:
echo "+1-100" > xxx/badblock, this will make sector [1-100] as bad
blocks.
echo "-20-30" > xxx/badblock, this will make sector [20-30] good
If badblocks are accessed, the nullb disk will return IO error. Other
parts of the disk can accessed in normal way.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Software must flush disk cache to guarantee data safety. To check if
software correctly does disk cache flush, we must know the behavior of
disk. But physical disk behavior is uncontrollable. Even software
doesn't do the flush, the disk probably does the flush. This patch tries
to emulate a cache in the test disk.
All write will go to a cache first, when the cache is full, we then
flush some data to disk storage. A flush request will flush all data of
the cache to disk storage. A FUA write will write to memory store
directly and revalidate data in cache. If there is a power failure (by
writing to power attribute, 'echo 0 > disk_name/power'), we discard all
data in the cache, but preserve the data in disk storage. Later we can
power on the disk again as usual (write 1 to 'power' attribute), then we
can check data integrity and very if software does everything correctly.
A new attribute 'cache_size' (in MB) is added to configure cache size.
Based on original patch from Kyungchan Koh
Signed-off-by: Kyungchan Koh <kkc6196@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In test, we usually expect controllable disk speed. For example, in a
raid array, we'd like some disks are fast and some are slow. MD RAID
actually has a feature for this. To test the feature, we'd like to make
the disk run in specific speed.
block throttling probably can be used for this purpose, but it requires
cgroup setup. Here we just implement a simple throttling mechanism in
the driver. There is slight fluctuation in the mechanism, but it's good
enough for test.
To configure the bandwidth cap, user sets the 'mbps' attribute. mbps is
MB/s.
Based on original patch from Kyungchan Koh
Signed-off-by: Kyungchan Koh <kkc6196@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
discard makes sense for memory backed disk. And also it's useful to test
if upper layer supports dicard correctly.
User configures 'discard' attribute to enable/disable dicard support.
Based on original patch from Kyungchan Koh
Signed-off-by: Kyungchan Koh <kkc6196@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This adds memory backed store in nullb.
User configure 'memory_backed' attribute for this. By default, nullb
disk doesn't use memory backed store.
Based on original patch from Kyungchan Koh
Signed-off-by: Kyungchan Koh <kkc6196@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We now dynamically create disks. Managing the disk index with ida to
avoid bump up the index too much.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The device created in nullb configfs interface isn't power on by
default. After user configures the device, user can do 'echo 1 >
xxx/nullb/device_name/power' to power on the device, which will create a
disk. the xxx/nullb/device_name/index is the disk index, so if the index
is 2, the new created disk should be named as /dev/nullb2. Note, the
'index' is only valid after disk is power on.
'echo 0 > xxx/nullb/device_name/power' will remove the disk. Note, this
doesn't remove the device. To remove the device, user should do 'rmdir
xxx/nullb/device_name'. Removing the device will remove the disk too.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add configfs interface for nullb. configfs interface is more flexible
and easy to configure in a per-disk basis.
Configuration is something like this:
mount -t configfs none /mnt
Checking which features the driver supports:
cat /mnt/nullb/features
The 'features' attribute is for future extension. We probably will add
new features into the driver, userspace can check this attribute to find
the supported features.
Create/remove a device:
mkdir/rmdir /mnt/nullb/a
Then configure the device by setting attributes under /mnt/nullb/a, most
of nullb supported module parameters are converted to attributes:
size; /* device size in MB */
completion_nsec; /* time in ns to complete a request */
submit_queues; /* number of submission queues */
home_node; /* home node for the device */
queue_mode; /* block interface */
blocksize; /* block size */
irqmode; /* IRQ completion handler */
hw_queue_depth; /* queue depth */
use_lightnvm; /* register as a LightNVM device */
blocking; /* blocking blk-mq device */
use_per_node_hctx; /* use per-node allocation for hardware context */
Note, creating a device doesn't create a disk immediately. Creating a
disk is done in two phases: create a device and then power on the
device. Next patch will introduce device power on.
Based on original patch from Kyungchan Koh
Signed-off-by: Kyungchan Koh <kkc6196@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When we switch to configfs interface, each disk could have different
configuration. To prepare for the change, we move most disk setting to a
separate data structure. The existing module parameter interface is
kept. The 'nr_devices' and 'shared_tags' don't make sense for per-disk
setting, so they are remained as global settings.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
My initial impulse was to check for IS_ERR_OR_NULL() but when I looked
at this code a bit more closely, we should only need to check for
IS_ERR().
The blk_mq_alloc_tag_set() returns negative error codes and zero on
success so we can just do an "if (rc) goto err_out;". It's better to
preserve the error code anyhow. The blk_mq_init_queue() returns error
pointers on failure, it never returns NULL. We can also remove the
"q = NULL;" at the start because that's no longer needed.
Fixes: ca33dd92968b ("skd: Convert to blk-mq")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Someone got too agressive about removing initializations and
accidentally removed the "rc = 0;" which is required.
Fixes: c830da8cbc7b ("skd: Remove superfluous initializations from skd_isr_completion_posted()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove the driver version information because this information
is not useful in an upstream kernel driver.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Bump the driver version. Remove the build ID because build IDs do
not make sense for an upstream kernel driver. Keep the driver
version in the module information but do not report it during every
load, unload or probe.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Only take skdev->lock if necessary.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch does not change any functionality but makes the code
more brief.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Every single coherent DMA memory buffer occupies at least one page.
Reduce memory usage by switching from coherent buffers to streaming
DMA for I/O requests (struct skd_fitmsg_context) and S/G-lists
(struct fit_sg_descriptor[]).
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since skd_device.in_flight is only used to display the number of
in-flight requests in debug messages, remove that member and
introduce skd_in_flight(). That last function relies on the block
layer to determine the number of in flight requests.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove the timeout slot variables and rely on the block layer to
detect request timeouts.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Introduce a tag set and a blk_mq_ops structure. Set .cmd_size such
that struct request and struct skd_request_context are allocated
through a single allocation. Remove the skd_request_context.req
pointer. Make queue starting asynchronous such that this can occur
safely from interrupt context. Use locking to protect skdev->skmsg
and *skdev->skmsg against concurrent access from concurrent
.queue_rq() calls. Introduce the functions skd_init_request() and
skd_exit_request() to set up / clean up the per-request S/G-list.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Set request_queue.cmd_size, introduce skd_init_rq() and skd_exit_rq()
and remove skd_device.skreq_table.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Issue a warning if a NULL argument is passed to skd_free_sg_list().
Move this function up to make the blk-mq conversion patch easier
to read.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch does not change any functionality but makes the blk-mq
conversion patch easier to read.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The only functional change in this patch is that the skd_fitmsg_context
in which requests are accumulated is changed from a local variable into
a member of struct skd_device. This patch will make the blk-mq conversion
easier.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Convert the per-device scalar variables that are protected by the
queue lock into atomics such that it becomes safe to access these
variables without holding the queue lock.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Use the request tag when allocating a skd_fitmsg_context or
skd_request_context such that the lists used to track free elements
can be eliminated. Swap the skd_end_request() and skd_release_req()
calls to avoid triggering a use-after-free. Remove
skd_fitmsg_context.state and .outstanding because FIT messages are
shared among requests and because updating a FIT message after a
request has finished whould trigger a use-after-free.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The debug code in skd_send_special_fitmsg() assumes that req.n_sg
represents the number of S/G descriptors. However, skd_construct()
initializes that member variable to zero. Set req.n_sg to one such
that the debugging code in skd_send_special_fitmsg() works as
expected.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
