| Age | Commit message (Collapse) | Author |
|---|
|
If the LightNVM subsystem is not compiled into the kernel, and the
null_blk device driver requests lightnvm to be initialized. The call to
nvm_register fails and the null_add_dev function cleans up the
initialization. However, at this point the null block device has
already been added to the nullb_list and thus a second cleanup will
occur when the function has returned, that leads to a double call to
blk_cleanup_queue.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In case /dev/fdX is open with O_NDELAY / O_NONBLOCK, floppy_open() immediately
succeeds, without performing any further media / controller preparations.
That's "correct" wrt. the NODELAY flag, but is hardly correct wrt. the rest
of the floppy driver, that is not really O_NONBLOCK ready, at all. Therefore
it's not too surprising, that subsequent attempts to work with the
filedescriptor produce bad results. Namely, syzkaller tool has been able
to livelock mmap() on the returned fd to keep waiting on the page unlock
bit forever.
Quite frankly, I have trouble defining what non-blocking behavior would be for
floppies. Is waiting ages for the driver to actually succeed reading a sector
blocking operation? Is waiting for drive motor to start blocking operation? How
about in case of virtualized floppies?
One option would be returning EWOULDBLOCK in case O_NDLEAY / O_NONBLOCK is
being passed to open(). That has a theoretical potential of breaking some
arcane and archaic userspace though.
Let's take a more conservative aproach, and accept the O_NDLEAY flag, and let
the driver behave as usual.
While at it, clean up a bit handling of !(mode & (FMODE_READ|FMODE_WRITE))
case and return EINVAL instead of succeeding as well.
Spotted by syzkaller tool.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
System block allows the device to initialize with its configured media
manager. The system blocks is written to disk, and read again when media
manager is determined. For this to work, the backend must store the
data. Device drivers, such as null_blk, does not have any backend
storage. This patch allows the media manager to be initialized without a
storage backend.
It also fix incorrect configuration of capabilities in null_blk, as it
does not support get/set bad block interface.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/linux-block into for-linus
Locking fix from Jiri
|
|
floppy_revalidate() doesn't perform any error handling on lock_fdc()
result. lock_fdc() might actually be interrupted by a signal (it waits for
fdc becoming non-busy interruptibly). In such case, floppy_revalidate()
proceeds as if it had claimed the lock, but it fact it doesn't.
In case of multiple threads trying to open("/dev/fdX"), this leads to
serious corruptions all over the place, because all of a sudden there is
no critical section protection (that'd otherwise be guaranteed by locked
fd) whatsoever.
While at this, fix the fact that the 'interruptible' parameter to
lock_fdc() doesn't make any sense whatsoever, because we always wait
interruptibly anyway.
Most of the lock_fdc() callsites do properly handle error (and propagate
EINTR), but floppy_revalidate() and floppy_check_events() don't. Fix this.
Spotted by 'syzkaller' tool.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus
|
|
Need to reallocate ring info in the resume path, because info->rinfo was freed
in blkif_free(). And 'multi-queue-max-queues' backend reports may have been
changed.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"The two main changes are aio support in CephFS, and a series that
fixes several issues in the authentication key timeout/renewal code.
On top of that are a variety of cleanups and minor bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: remove outdated comment
libceph: kill off ceph_x_ticket_handler::validity
libceph: invalidate AUTH in addition to a service ticket
libceph: fix authorizer invalidation, take 2
libceph: clear messenger auth_retry flag if we fault
libceph: fix ceph_msg_revoke()
libceph: use list_for_each_entry_safe
ceph: use i_size_{read,write} to get/set i_size
ceph: re-send AIO write request when getting -EOLDSNAP error
ceph: Asynchronous IO support
ceph: Avoid to propagate the invalid page point
ceph: fix double page_unlock() in page_mkwrite()
rbd: delete an unnecessary check before rbd_dev_destroy()
libceph: use list_next_entry instead of list_entry_next
ceph: ceph_frag_contains_value can be boolean
ceph: remove unused functions in ceph_frag.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
|
|
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull lightnvm fixes and updates from Jens Axboe:
"This should have been part of the drivers branch, but it arrived a bit
late and wasn't based on the official core block driver branch. So
they got a small scolding, but got a pass since it's still new. Hence
it's in a separate branch.
This is mostly pure fixes, contained to lightnvm/, and minor feature
additions"
* 'for-4.5/lightnvm' of git://git.kernel.dk/linux-block: (26 commits)
lightnvm: ensure that nvm_dev_ops can be used without CONFIG_NVM
lightnvm: introduce factory reset
lightnvm: use system block for mm initialization
lightnvm: introduce ioctl to initialize device
lightnvm: core on-disk initialization
lightnvm: introduce mlc lower page table mappings
lightnvm: add mccap support
lightnvm: manage open and closed blocks separately
lightnvm: fix missing grown bad block type
lightnvm: reference rrpc lun in rrpc block
lightnvm: introduce nvm_submit_ppa
lightnvm: move rq->error to nvm_rq->error
lightnvm: support multiple ppas in nvm_erase_ppa
lightnvm: move the pages per block check out of the loop
lightnvm: sectors first in ppa list
lightnvm: fix locking and mempool in rrpc_lun_gc
lightnvm: put block back to gc list on its reclaim fail
lightnvm: check bi_error in gc
lightnvm: return the get_bb_tbl return value
lightnvm: refactor end_io functions for sync
...
|
|
Pull block driver updates from Jens Axboe:
"This is the block driver pull request for 4.5, with the exception of
NVMe, which is in a separate branch and will be posted after this one.
This pull request contains:
- A set of bcache stability fixes, which have been acked by Kent.
These have been used and tested for more than a year by the
community, so it's about time that they got in.
- A set of drbd updates from the drbd team (Andreas, Lars, Philipp)
and Markus Elfring, Oleg Drokin.
- A set of fixes for xen blkback/front from the usual suspects, (Bob,
Konrad) as well as community based fixes from Kiri, Julien, and
Peng.
- A 2038 time fix for sx8 from Shraddha, with a fix from me.
- A small mtip32xx cleanup from Zhu Yanjun.
- A null_blk division fix from Arnd"
* 'for-4.5/drivers' of git://git.kernel.dk/linux-block: (71 commits)
null_blk: use sector_div instead of do_div
mtip32xx: restrict variables visible in current code module
xen/blkfront: Fix crash if backend doesn't follow the right states.
xen/blkback: Fix two memory leaks.
xen/blkback: make st_ statistics per ring
xen/blkfront: Handle non-indirect grant with 64KB pages
xen-blkfront: Introduce blkif_ring_get_request
xen-blkback: clear PF_NOFREEZE for xen_blkif_schedule()
xen/blkback: Free resources if connect_ring failed.
xen/blocks: Return -EXX instead of -1
xen/blkback: make pool of persistent grants and free pages per-queue
xen/blkback: get the number of hardware queues/rings from blkfront
xen/blkback: pseudo support for multi hardware queues/rings
xen/blkback: separate ring information out of struct xen_blkif
xen/blkfront: correct setting for xen_blkif_max_ring_order
xen/blkfront: make persistent grants pool per-queue
xen/blkfront: Remove duplicate setting of ->xbdev.
xen/blkfront: Cleanup of comments, fix unaligned variables, and syntax errors.
xen/blkfront: negotiate number of queues/rings to be used with backend
xen/blkfront: split per device io_lock
...
|
|
The rbd_dev_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Pull core block updates from Jens Axboe:
"We don't have a lot of core changes this time around, it's mostly in
drivers, which will come in a subsequent pull.
The cores changes include:
- blk-mq
- Prep patch from Christoph, changing blk_mq_alloc_request() to
take flags instead of just using gfp_t for sleep/nosleep.
- Doc patch from me, clarifying the difference between legacy
and blk-mq for timer usage.
- Fixes from Raghavendra for memory-less numa nodes, and a reuse
of CPU masks.
- Cleanup from Geliang Tang, using offset_in_page() instead of open
coding it.
- From Ilya, rename request_queue slab to it reflects what it holds,
and a fix for proper use of bdgrab/put.
- A real fix for the split across stripe boundaries from Keith. We
yanked a broken version of this from 4.4-rc final, this one works.
- From Mike Krinkin, emit a trace message when we split.
- From Wei Tang, two small cleanups, not explicitly clearing memory
that is already cleared"
* 'for-4.5/core' of git://git.kernel.dk/linux-block:
block: use bd{grab,put}() instead of open-coding
block: split bios to max possible length
block: add call to split trace point
blk-mq: Avoid memoryless numa node encoded in hctx numa_node
blk-mq: Reuse hardware context cpumask for tags
blk-mq: add a flags parameter to blk_mq_alloc_request
Revert "blk-flush: Queue through IO scheduler when flush not required"
block: clarify blk_add_timer() use case for blk-mq
bio: use offset_in_page macro
block: do not initialise statics to 0 or NULL
block: do not initialise globals to 0 or NULL
block: rename request_queue slab cache
|
|
For the purpose of communicating the optional presence of a 'struct
page' for the pfn returned from ->direct_access(), introduce a type that
encapsulates a page-frame-number plus flags. These flags contain the
historical "page_link" encoding for a scatterlist entry, but can also
denote "device memory". Where "device memory" is a set of pfns that are
not part of the kernel's linear mapping by default, but are accessed via
the same memory controller as ram.
The motivation for this new type is large capacity persistent memory
that needs struct page entries in the 'memmap' to support 3rd party DMA
(i.e. O_DIRECT I/O with a persistent memory source/target). However,
we also need it in support of maintaining a list of mapped inodes which
need to be unmapped at driver teardown or freeze_bdev() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave@sr71.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The use of idr_remove() is forbidden in the callback functions of
idr_for_each(). It is therefore unsafe to call idr_remove in
zram_remove().
This patch moves the call to idr_remove() from zram_remove() to
hot_remove_store(). In the detroy_devices() path, idrs are removed by
idr_destroy(). This solves an use-after-free detected by KASan.
[akpm@linux-foundation.org: fix coding stype, per Sergey]
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge first patch-bomb from Andrew Morton:
- A few hotfixes which missed 4.4 becasue I was asleep. cc'ed to
-stable
- A few misc fixes
- OCFS2 updates
- Part of MM. Including pretty large changes to page-flags handling
and to thp management which have been buffered up for 2-3 cycles now.
I have a lot of MM material this time.
[ It turns out the THP part wasn't quite ready, so that got dropped from
this series - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
zsmalloc: reorganize struct size_class to pack 4 bytes hole
mm/zbud.c: use list_last_entry() instead of list_tail_entry()
zram/zcomp: do not zero out zcomp private pages
zram: pass gfp from zcomp frontend to backend
zram: try vmalloc() after kmalloc()
zram/zcomp: use GFP_NOIO to allocate streams
mm: add tracepoint for scanning pages
drivers/base/memory.c: fix kernel warning during memory hotplug on ppc64
mm/page_isolation: use macro to judge the alignment
mm: fix noisy sparse warning in LIBCFS_ALLOC_PRE()
mm: rework virtual memory accounting
include/linux/memblock.h: fix ordering of 'flags' argument in comments
mm: move lru_to_page to mm_inline.h
Documentation/filesystems: describe the shared memory usage/accounting
memory-hotplug: don't BUG() in register_memory_resource()
hugetlb: make mm and fs code explicitly non-modular
mm/swapfile.c: use list_for_each_entry_safe in free_swap_count_continuations
mm: /proc/pid/clear_refs: no need to clear VM_SOFTDIRTY in clear_soft_dirty_pmd()
mm: make sure isolate_lru_page() is never called for tail page
vmstat: make vmstat_updater deferrable again and shut down on idle
...
|
|
Do not __GFP_ZERO allocated zcomp ->private pages. We keep allocated
streams around and use them for read/write requests, so we supply a
zeroed out ->private to compression algorithm as a scratch buffer only
once -- the first time we use that stream. For the rest of IO requests
served by this stream ->private usually contains some temporarily data
from the previous requests.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Each zcomp backend uses own gfp flag but it's pointless because the
context they could be called is driven by upper layer(ie, zcomp
frontend). As well, zcomp frondend could call them in different
context. One context(ie, zram init part) is it should be better to make
sure successful allocation other context(ie, further stream allocation
part for accelarating I/O speed) is just optional so let's pass gfp down
from driver (ie, zcomp frontend) like normal MM convention.
[sergey.senozhatsky@gmail.com: add missing __vmalloc zero and highmem gfps]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we're using LZ4 multi compression streams for zram swap, we found
out page allocation failure message in system running test. That was
not only once, but a few(2 - 5 times per test). Also, some failure
cases were continually occurring to try allocation order 3.
In order to make parallel compression private data, we should call
kzalloc() with order 2/3 in runtime(lzo/lz4). But if there is no order
2/3 size memory to allocate in that time, page allocation fails. This
patch makes to use vmalloc() as fallback of kmalloc(), this prevents
page alloc failure warning.
After using this, we never found warning message in running test, also
It could reduce process startup latency about 60-120ms in each case.
For reference a call trace :
Binder_1: page allocation failure: order:3, mode:0x10c0d0
CPU: 0 PID: 424 Comm: Binder_1 Tainted: GW 3.10.49-perf-g991d02b-dirty #20
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x10/0x1c
dump_stack+0x1c/0x28
warn_alloc_failed+0xfc/0x11c
__alloc_pages_nodemask+0x724/0x7f0
__get_free_pages+0x14/0x5c
kmalloc_order_trace+0x38/0xd8
zcomp_lz4_create+0x2c/0x38
zcomp_strm_alloc+0x34/0x78
zcomp_strm_multi_find+0x124/0x1ec
zcomp_strm_find+0xc/0x18
zram_bvec_rw+0x2fc/0x780
zram_make_request+0x25c/0x2d4
generic_make_request+0x80/0xbc
submit_bio+0xa4/0x15c
__swap_writepage+0x218/0x230
swap_writepage+0x3c/0x4c
shrink_page_list+0x51c/0x8d0
shrink_inactive_list+0x3f8/0x60c
shrink_lruvec+0x33c/0x4cc
shrink_zone+0x3c/0x100
try_to_free_pages+0x2b8/0x54c
__alloc_pages_nodemask+0x514/0x7f0
__get_free_pages+0x14/0x5c
proc_info_read+0x50/0xe4
vfs_read+0xa0/0x12c
SyS_read+0x44/0x74
DMA: 3397*4kB (MC) 26*8kB (RC) 0*16kB 0*32kB 0*64kB 0*128kB 0*256kB
0*512kB 0*1024kB 0*2048kB 0*4096kB = 13796kB
[minchan@kernel.org: change vmalloc gfp and adding comment about gfp]
[sergey.senozhatsky@gmail.com: tweak comments and styles]
Signed-off-by: Kyeongdon Kim <kyeongdon.kim@lge.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We can end up allocating a new compression stream with GFP_KERNEL from
within the IO path, which may result is nested (recursive) IO
operations. That can introduce problems if the IO path in question is a
reclaimer, holding some locks that will deadlock nested IOs.
Allocate streams and working memory using GFP_NOIO flag, forbidding
recursive IO and FS operations.
An example:
inconsistent {IN-RECLAIM_FS-W} -> {RECLAIM_FS-ON-W} usage.
git/20158 [HC0[0]:SC0[0]:HE1:SE1] takes:
(jbd2_handle){+.+.?.}, at: start_this_handle+0x4ca/0x555
{IN-RECLAIM_FS-W} state was registered at:
__lock_acquire+0x8da/0x117b
lock_acquire+0x10c/0x1a7
start_this_handle+0x52d/0x555
jbd2__journal_start+0xb4/0x237
__ext4_journal_start_sb+0x108/0x17e
ext4_dirty_inode+0x32/0x61
__mark_inode_dirty+0x16b/0x60c
iput+0x11e/0x274
__dentry_kill+0x148/0x1b8
shrink_dentry_list+0x274/0x44a
prune_dcache_sb+0x4a/0x55
super_cache_scan+0xfc/0x176
shrink_slab.part.14.constprop.25+0x2a2/0x4d3
shrink_zone+0x74/0x140
kswapd+0x6b7/0x930
kthread+0x107/0x10f
ret_from_fork+0x3f/0x70
irq event stamp: 138297
hardirqs last enabled at (138297): debug_check_no_locks_freed+0x113/0x12f
hardirqs last disabled at (138296): debug_check_no_locks_freed+0x33/0x12f
softirqs last enabled at (137818): __do_softirq+0x2d3/0x3e9
softirqs last disabled at (137813): irq_exit+0x41/0x95
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(jbd2_handle);
<Interrupt>
lock(jbd2_handle);
*** DEADLOCK ***
5 locks held by git/20158:
#0: (sb_writers#7){.+.+.+}, at: [<ffffffff81155411>] mnt_want_write+0x24/0x4b
#1: (&type->i_mutex_dir_key#2/1){+.+.+.}, at: [<ffffffff81145087>] lock_rename+0xd9/0xe3
#2: (&sb->s_type->i_mutex_key#11){+.+.+.}, at: [<ffffffff8114f8e2>] lock_two_nondirectories+0x3f/0x6b
#3: (&sb->s_type->i_mutex_key#11/4){+.+.+.}, at: [<ffffffff8114f909>] lock_two_nondirectories+0x66/0x6b
#4: (jbd2_handle){+.+.?.}, at: [<ffffffff811e31db>] start_this_handle+0x4ca/0x555
stack backtrace:
CPU: 2 PID: 20158 Comm: git Not tainted 4.1.0-rc7-next-20150615-dbg-00016-g8bdf555-dirty #211
Call Trace:
dump_stack+0x4c/0x6e
mark_lock+0x384/0x56d
mark_held_locks+0x5f/0x76
lockdep_trace_alloc+0xb2/0xb5
kmem_cache_alloc_trace+0x32/0x1e2
zcomp_strm_alloc+0x25/0x73 [zram]
zcomp_strm_multi_find+0xe7/0x173 [zram]
zcomp_strm_find+0xc/0xe [zram]
zram_bvec_rw+0x2ca/0x7e0 [zram]
zram_make_request+0x1fa/0x301 [zram]
generic_make_request+0x9c/0xdb
submit_bio+0xf7/0x120
ext4_io_submit+0x2e/0x43
ext4_bio_write_page+0x1b7/0x300
mpage_submit_page+0x60/0x77
mpage_map_and_submit_buffers+0x10f/0x21d
ext4_writepages+0xc8c/0xe1b
do_writepages+0x23/0x2c
__filemap_fdatawrite_range+0x84/0x8b
filemap_flush+0x1c/0x1e
ext4_alloc_da_blocks+0xb8/0x117
ext4_rename+0x132/0x6dc
? mark_held_locks+0x5f/0x76
ext4_rename2+0x29/0x2b
vfs_rename+0x540/0x636
SyS_renameat2+0x359/0x44d
SyS_rename+0x1e/0x20
entry_SYSCALL_64_fastpath+0x12/0x6f
[minchan@kernel.org: add stable mark]
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Kyeongdon Kim <kyeongdon.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
|
|
Pull first round of SCSI updates from James Bottomley:
"This includes driver updates from the usual suspects (bfa, arcmsr,
scsi_dh_alua, lpfc, storvsc, cxlflash).
The major change is the addition of the hisi_sas driver, which is an
ARM platform device for SAS. The other change of note is an enormous
style transformation to the atp870u driver (which is our worst written
SCSI driver)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (169 commits)
cxlflash: Enable device id for future IBM CXL adapter
cxlflash: Resolve oops in wait_port_offline
cxlflash: Fix to resolve cmd leak after host reset
cxlflash: Removed driver date print
cxlflash: Fix to avoid virtual LUN failover failure
cxlflash: Fix to escalate LINK_RESET also on port 1
storvsc: Tighten up the interrupt path
storvsc: Refactor the code in storvsc_channel_init()
storvsc: Properly support Fibre Channel devices
storvsc: Fix a bug in the layout of the hv_fc_wwn_packet
mvsas: Add SGPIO support to Marvell 94xx
mpt3sas: A correction in unmap_resources
hpsa: Add box and bay information for enclosure devices
hpsa: Change SAS transport devices to bus 0.
hpsa: fix path_info_show
cciss: print max outstanding commands as a hex value
scsi_debug: Increase the reported optimal transfer length
lpfc: Update version to 11.0.0.10 for upstream patch set
lpfc: Use kzalloc instead of kmalloc
lpfc: Delete unnecessary checks before the function call "mempool_destroy"
...
|
|
Dividing a sector_t number should be done using sector_div rather than do_div
to optimize the 32-bit sector_t case, and with the latest do_div optimizations,
we now get a compile-time warning for this:
arch/arm/include/asm/div64.h:32:95: note: expected 'uint64_t * {aka long long unsigned int *}' but argument is of type 'sector_t * {aka long unsigned int *}'
drivers/block/null_blk.c:521:81: warning: comparison of distinct pointer types lacks a cast
This changes the newly added code to use sector_div. It is a simplified version
of the original patch, as Linus Torvalds pointed out that we should not be using
an expensive division function in the first place.
This version was suggested by Matias Bjorling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Matias Bjorling <m@bjorling.me>
Fixes: b2b7e00148a2 ("null_blk: register as a LightNVM device")
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-4.5/drivers
Konrad writes:
The pull is based on converting the backend driver into an multiqueue
driver and exposing more than one queue to the frontend. As such we had
to modify the frontend and also fix a bunch of bugs around this.
The original work is based on Arianna Avanzini's work as an OPW intern.
Bob took over the work and had been massaging it for quite some time.
Also included are are features to 64KB page support for ARM and various
bug-fixes.
|
|
To implement sync I/O support within the LightNVM core, the end_io
functions are refactored to take an end_io function pointer instead of
testing for initialized media manager, followed by calling its end_io
function.
Sync I/O can then be implemented using a callback that signal I/O
completion. This is similar to the logic found in blk_to_execute_io().
By implementing it this way, the underlying device I/Os submission logic
is abstracted away from core, targets, and media managers.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
|
|
The modified variables are only used in the file mtip32xx.c.
As such, the static keyword is inserted to define that object
to be only visible to the current code module during compilation.
Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
[folded a fix by Dan Carpenter]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The max outstanding commands is being printed with a 0x prefix to
suggest it is a hex value, when in fact the integer decimal %d format
specifier is being used and this is a bit confusing. Use %x instead to
match the proceeding 0x prefix.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We have split the setting up of all the resources in two steps:
1) talk_to_blkback - which figures out the num_ring_pages (from
the default value of zero), sets up shadow and so
2) blkfront_connect - does the real part of filling out the
internal structures.
The problem is if we bypass the 1) step and go straight to 2)
and call blkfront_setup_indirect where we use the macro
BLK_RING_SIZE - which returns an negative value (because
sz is zero - since num_ring_pages is zero - since it has never
been set).
We can fix this by making sure that we always have called
talk_to_blkback before going to blkfront_connect.
Or we could set in blkfront_probe info->nr_ring_pages = 1
to have a default value. But that looks odd - as we haven't
actually negotiated any ring size.
This patch changes XenbusStateConnected state to detect if
we haven't done the initial handshake - and if so continue
on as if were in XenbusStateInitWait state.
We also roll the error recovery (freeing the structure) into
talk_to_blkback error path - which is safe since that function
is only called from blkback_changed.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
This patch fixs two memleaks:
backtrace:
[<ffffffff817ba5e8>] kmemleak_alloc+0x28/0x50
[<ffffffff81205e3b>] kmem_cache_alloc+0xbb/0x1d0
[<ffffffff81534028>] xen_blkbk_probe+0x58/0x230
[<ffffffff8146adb6>] xenbus_dev_probe+0x76/0x130
[<ffffffff81511716>] driver_probe_device+0x166/0x2c0
[<ffffffff815119bc>] __device_attach_driver+0xac/0xb0
[<ffffffff8150fa57>] bus_for_each_drv+0x67/0x90
[<ffffffff81511ab7>] __device_attach+0xc7/0x120
[<ffffffff81511b23>] device_initial_probe+0x13/0x20
[<ffffffff8151059a>] bus_probe_device+0x9a/0xb0
[<ffffffff8150f0a1>] device_add+0x3b1/0x5c0
[<ffffffff8150f47e>] device_register+0x1e/0x30
[<ffffffff8146a9e8>] xenbus_probe_node+0x158/0x170
[<ffffffff8146abaf>] xenbus_dev_changed+0x1af/0x1c0
[<ffffffff8146b1bb>] backend_changed+0x1b/0x20
[<ffffffff81468ca6>] xenwatch_thread+0xb6/0x160
unreferenced object 0xffff880007ba8ef8 (size 224):
backtrace:
[<ffffffff817ba5e8>] kmemleak_alloc+0x28/0x50
[<ffffffff81205c73>] __kmalloc+0xd3/0x1e0
[<ffffffff81534d87>] frontend_changed+0x2c7/0x580
[<ffffffff8146af12>] xenbus_otherend_changed+0xa2/0xb0
[<ffffffff8146b2c0>] frontend_changed+0x10/0x20
[<ffffffff81468ca6>] xenwatch_thread+0xb6/0x160
[<ffffffff810d3e97>] kthread+0xd7/0xf0
[<ffffffff817c4a9f>] ret_from_fork+0x3f/0x70
[<ffffffffffffffff>] 0xffffffffffffffff
unreferenced object 0xffff8800048dcd38 (size 224):
The first leak is caused by not put() the be->blkif reference
which we had gotten in xen_blkif_alloc(), while the second is
us not freeing blkif->rings in the right place.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Make st_* statistics per ring and the VBD sysfs would iterate over all the
rings.
Note: xenvbd_sysfs_delif() is called in xen_blkbk_remove() before all rings
are torn down, so it's safe.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
---
v2: Aligned the variables on the same column.
|
|
The minimal size of request in the block framework is always PAGE_SIZE.
It means that when 64KB guest is support, the request will at least be
64KB.
Although, if the backend doesn't support indirect descriptor (such as QDISK
in QEMU), a ring request is only able to accommodate 11 segments of 4KB
(i.e 44KB).
The current frontend is assuming that an I/O request will always fit in
a ring request. This is not true any more when using 64KB page
granularity and will therefore crash during boot.
On ARM64, the ABI is completely neutral to the page granularity used by
the domU. The guest has the choice between different page granularity
supported by the processors (for instance on ARM64: 4KB, 16KB, 64KB).
This can't be enforced by the hypervisor and therefore it's possible to
run guests using different page granularity.
So we can't mandate the block backend to support indirect descriptor
when the frontend is using 64KB page granularity and have to fix it
properly in the frontend.
The solution exposed below is based on modifying directly the frontend
guest rather than asking the block framework to support smaller size
(i.e < PAGE_SIZE). This is because the change is the block framework are
not trivial as everything seems to relying on a struct *page (see [1]).
Although, it may be possible that someone succeed to do it in the future
and we would therefore be able to use it.
Given that a block request may not fit in a single ring request, a
second request is introduced for the data that cannot fit in the first
one. This means that the second ring request should never be used on
Linux if the page size is smaller than 44KB.
To achieve the support of the extra ring request, the block queue size
is divided by two. Therefore, the ring will always contain enough space
to accommodate 2 ring requests. While this will reduce the overall
performance, it will make the implementation more contained. The way
forward to get better performance is to implement in the backend either
indirect descriptor or multiple grants ring.
Note that the parameters blk_queue_max_* helpers haven't been updated.
The block code will set the mimimum size supported and we may be able
to support directly any change in the block framework that lower down
the minimal size of a request.
[1] http://lists.xen.org/archives/html/xen-devel/2015-08/msg02200.html
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
The code to get a request is always the same. Therefore we can factorize
it in a single function.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
xen_blkif_schedule() kthread calls try_to_freeze() at the beginning of
every attempt to purge the LRU. This operation can't ever succeed though,
as the kthread hasn't marked itself as freezable.
Before (hopefully eventually) kthread freezing gets converted to fileystem
freezing, we'd rather mark xen_blkif_schedule() freezable (as it can
generate I/O during suspend).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
With the multi-queue support we could fail at setting up
some of the rings and fail the connection. That meant that
all resources tied to rings[0..n-1] (where n is the ring
that failed to be setup). Eventually the frontend will switch
to the states and we will call xen_blkif_disconnect.
However we do not want to be at the mercy of the frontend
deciding when to change states. This allows us to do the
cleanup right away and freeing resources.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Lets return sensible values instead of -1.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Make pool of persistent grants and free pages per-queue/ring instead of
per-device to get better scalability.
Test was done based on null_blk driver:
dom0: v4.2-rc8 16vcpus 10GB "modprobe null_blk"
domu: v4.2-rc8 16vcpus 10GB
[test]
rw=read
direct=1
ioengine=libaio
bs=4k
time_based
runtime=30
filename=/dev/xvdb
numjobs=16
iodepth=64
iodepth_batch=64
iodepth_batch_complete=64
group_reporting
Results:
iops1: After patch "xen/blkfront: make persistent grants per-queue".
iops2: After this patch.
Queues: 1 4 8 16
Iops orig(k): 810 1064 780 700
Iops1(k): 810 1230(~20%) 1024(~20%) 850(~20%)
Iops2(k): 810 1410(~35%) 1354(~75%) 1440(~100%)
With 4 queues after this commit we can get ~75% increase in IOPS, and
performance won't drop if increasing queue numbers.
Please find the respective chart in this link:
https://www.dropbox.com/s/agrcy2pbzbsvmwv/iops.png?dl=0
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Backend advertises "multi-queue-max-queues" to front, also get the negotiated
number from "multi-queue-num-queues" written by blkfront.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Preparatory patch for multiple hardware queues (rings). The number of
rings is unconditionally set to 1, larger number will be enabled in
"xen/blkback: get the number of hardware queues/rings from blkfront".
Signed-off-by: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
---
v2: Align variables in the structures.
|
|
Split per ring information to an new structure "xen_blkif_ring", so that one vbd
device can be associated with one or more rings/hardware queues.
Introduce 'pers_gnts_lock' to protect the pool of persistent grants since we
may have multi backend threads.
This patch is a preparation for supporting multi hardware queues/rings.
Signed-off-by: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
---
v2: Align the variables in the structure.
|
|
According to this piece code:
"
pr_info("Invalid max_ring_order (%d), will use default max: %d.\n",
xen_blkif_max_ring_order, XENBUS_MAX_RING_GRANT_ORDER);
"
if xen_blkif_max_ring_order is bigger that XENBUS_MAX_RING_GRANT_ORDER,
need to set xen_blkif_max_ring_order using XENBUS_MAX_RING_GRANT_ORDER,
but not 0.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: "Roger Pau Monné" <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Make persistent grants per-queue/ring instead of per-device, so that we can
drop the 'dev_lock' and get better scalability.
Test was done based on null_blk driver:
dom0: v4.2-rc8 16vcpus 10GB "modprobe null_blk"
domu: v4.2-rc8 16vcpus 10GB
[test]
rw=read
direct=1
ioengine=libaio
bs=4k
time_based
runtime=30
filename=/dev/xvdb
numjobs=16
iodepth=64
iodepth_batch=64
iodepth_batch_complete=64
group_reporting
Queues: 1 4 8 16
Iops orig(k): 810 1064 780 700
Iops patched(k): 810 1230(~20%) 1024(~20%) 850(~20%)
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
We do the same exact operations a bit earlier in the
function.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
