| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
The ioctl path and the scsi tape path were not accounting
for their additions to the queue depth.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
If kmalloc() fails then cleanup and return failure (-1).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
The doorbell reset initially appears to work correctly,
the controller resets, comes up, some i/o can even be
done, but on at least some Smart Arrays in some servers,
it eventually causes a subsequent controller lockup due
to some kind of PCIe error, and kdump can end up leaving
the root filesystem in an unbootable state. For this
reason, until the problem is fixed, or at least isolated
to certain hardware enough to be avoided, the doorbell
reset should not be used at all.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
|
|
cciss: cleanup interrupt_not_for_us
In the case of MSI/MSIX interrutps, we don't need to check
if the interrupt is for us, and in the case of the intx interrupt
handler, when checking if the interrupt is for us, we don't need
to check if we're using MSI/MSIX, we know we're not.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: change printks to dev_warn, etc.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: separate cmd_alloc() and cmd_special_alloc()
cmd_alloc() took a parameter which caused it to either allocate
from a pre-allocated pool, or allocate using pci_alloc_consistent.
This parameter is always known at compile time, so this would
be better handled by breaking the function into two functions
and differentiating the cases by function names. Same goes
for cmd_free().
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: use consistent variable names
"h", for the hba structure and "c" for the command structures.
and get rid of trivial CCISS_LOCK macro.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: forbid hard reset of 640x boards
The 6402/6404 are two PCI devices -- two Smart Array controllers
-- that fit into one slot. It is possible to reset them independently,
however, they share a battery backed cache module. One of the pair
controls the cache and the 2nd one access the cache through the first
one. If you reset the one controlling the cache, the other one will
not be a happy camper. So we just forbid resetting this conjoined
mess.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: sanitize max commands
Some controllers might try to tell us they support 0 commands
in performant mode. This is a lie told by buggy firmware.
We have to be wary of this lest we try to allocate a negative
number of command blocks, which will be treated as unsigned,
and get an out of memory condition.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: Fix hard reset code.
Smart Array controllers newer than the P600 do not honor the
PCI power state method of resetting the controllers. Instead,
in these cases we can get them to reset via the "doorbell" register.
This escaped notice until we began using "performant" mode because
the fact that the controllers did not reset did not normally
impede subsequent operation, and so things generally appeared to
"work". Once the performant mode code was added, if the controller
does not reset, it remains in performant mode. The code immediately
after the reset presumes the controller is in "simple" mode
(which previously, it had remained in simple mode the whole time).
If the controller remains in performant mode any code which presumes
it is in simple mode will not work. So the reset needs to be fixed.
Unfortunately there are some controllers which cannot be reset by
either method. (eg. p800). We detect these cases by noticing that
the controller seems to remain in performant mode even after a
reset has been attempted. In those cases we ignore the controller,
as any commands outstanding on it will result in stale completions.
To sum up, we try to do a better job of resetting the controller if
"reset_devices" is set, and if it doesn't work, we ignore that
controller.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_reset_devices()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Rationale for this is that I will also need to use this code
in fixing kdump host reset code prior to having the hba structure.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_enter_performant_mode
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_wait_for_mode_change_ack()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: make cciss_put_controller_into_performant_mode as __devinit
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: cleanup some debug ifdefs
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_p600_dma_prefetch_quirk()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_enable_scsi_prefetch()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out CISS_signature_present()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_find_board_params
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: fix leak of ioremapped memory
in cciss_pci_init error path.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_find_cfgtables
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_wait_for_board_ready()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_find_memory_BAR()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: remove board_id parameter from cciss_interrupt_mode()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_board_disabled
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: factor out cciss_lookup_board_id
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
around so much.
cciss: save pdev pointer in per hba structure early to avoid passing it around so much.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
As a preparation for the removal of the big kernel
lock in the block layer, this removes the BKL
from the common ioctl handling code, moving it
into every single driver still using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
The definition of next_command also ended up in wrong place It ended up
inside an "#ifdef CONFIG_PROCFS". Already caught by Randy Dunlap and a
couple others. Tried to put it somewhere that made sense.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
call to put_controller_in_performant_mode was in the wrong place
The call inadvertently ended up in an error path.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Make sure we register the performant mode interrupt Another blunder.
Seemed to work because the call to put_controller_into_performant_mode was
never called.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Add support for new controllers due out next year. HP must continue to
support new controllers in older distros. All vendors require support be
upstream. These controllers support only 16 commands in simple mode but
can support up to 1024 in performant mode. See patch 5/6/ We have no
marketing names yet.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Add a mode of controller operation called Performant Mode. Even though
cciss has been deprecated in favor of hpsa there are new controllers due
out next year that HP must support in older vendor distros. Vendors
require all fixes/features be upstream. These new controllers support
only 16 commands in simple mode but support up to 1024 in performant mode.
This requires us to add this support at this late date.
The performant mode transport minimizes host PCI accesses by performinf
many completions per read. PCI writes are posted so the host can write
then immediately get off the bus not waiting for the writwe to complete to
the target. In the context of performant mode the host read out to a
controller pulls all posted writes into host memory ensuring the reply
queue is coherent.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Check to see if h->msi[x]_vector is set. We need this for a following
patch. Without this check we process one interrupt then stop because in
msi[x] mode the interrupt pending bit is not set. Not sure why we didn't
encounter this before.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Simplify the interrupt handler code to more closely match hpsa and to
hopefully make it easier to follow.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Clean up some code where we subit our io. The same 5 lines appeared
several times. Also helps for a following patch.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Change sizeof(x) / sizeof(*x) to ARRAY_SIZE(x).
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fix sparse warnings:
drivers/block/cciss.c:1591:37: warning: symbol 'i' shadows an earlier one
drivers/block/cciss.c:2437:21: warning: symbol 'i' shadows an earlier one
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
