| Age | Commit message (Collapse) | Author |
|---|
|
regmap: Support non-incrementing registers
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
|
|
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix typos 's/wit/with/' in the comments and sort headers alphabetically
in order to avoid duplicate includes in future.
Fixes: bcf7eac3d97f ("regmap: add SCCB support")
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regmap-4.19
regmap: Add support for SCCB
This is an I2C subset.
|
|
This adds Serial Camera Control Bus (SCCB) support for regmap API that
is intended to be used by some of Omnivision sensor drivers.
The ov772x and ov9650 drivers are going to use this SCCB regmap API.
The ov772x driver was previously only worked with the i2c controller
drivers that support I2C_FUNC_PROTOCOL_MANGLING, because the ov772x
device doesn't support repeated starts. After commit 0b964d183cbf
("media: ov772x: allow i2c controllers without
I2C_FUNC_PROTOCOL_MANGLING"), reading ov772x register is replaced with
issuing two separated i2c messages in order to avoid repeated start.
Using this SCCB regmap hides the implementation detail.
The ov9650 driver also issues two separated i2c messages to read the
registers as the device doesn't support repeated start. So it can
make use of this SCCB regmap.
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SLIMbus supports upto 16 bytes in value management messages,
so add support to read/writes upto 16 bytes.
This also removes redundant single register reg_read/reg_write.
Also useful for paged register access on SLIMbus interfaced codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
As per SLIMBus specs Value Elements and Information Elements
address map ranges from 0x000 - 0xFFF.
So allow register addresses up to 16 bits
Fixes: 7d6f7fb053ad ("regmap: add SLIMbus support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Capability to attach an existing clk to a MMIO regmap was
introduced in 4.17rc1.
However, when using attached clk, regmap does not do the clk_get.
Therefore it should not do the clk_put when freeing the MMIO
regmap context.
There does not appear to be any users of attached clocks yet
so this would be a good time to make this change before anything
depends on the existing behaviour.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'regmap/topic/mmio-clk' into regmap-next
|
|
|
|
into regmap-linus
|
|
|
|
Currently when debugfs_create_dir() fails we receive a warning message
that provides no indication as to what was the directory entry that
failed to be created.
Improve the warning message by printing the directory name that failed
in order to help debugging.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Free map->debugfs_name when debugfs_create_dir() failed to avoid memory
leak.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When allocating dummy names we need to store a pointer to the string we
allocate so that we don't leak it on free.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 9b947a13e7f6 ("regmap: use debugfs even when no device")
allows the usage of regmap debugfs even when there is no device
associated, which causes several warnings like this:
(NULL device *): Failed to create debugfs directory
This happens when the debugfs file name is 'dummy'.
The first dummy debugfs creation works fine, but subsequent creations
fail as they have all the same name.
Disambiguate the 'dummy' debugfs file name by adding a suffix entry,
so that the names become dummy0, dummy1, dummy2, etc.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
regmap_init_mmio_clk allows to specify a clock that needs to be enabled
while accessing the registers.
However, that clock is retrieved through its clock ID, which means it will
lookup that clock based on the current device that registers the regmap,
and, in the DT case, will only look in that device OF node.
This might be problematic if the clock to enable is stored in another node.
Let's add a function that allows to attach a clock that has already been
retrieved to a regmap in order to fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The handling for the first two cases in regmap_bulk_write is
essentially identical. The first case is just a better implementation of
the second, supporting 8 byte registers and doing the locking manually to
avoid bouncing the lock for each register. Drop some redundant code by
removing the second of these cases and allowing both situations to be
handled by the same code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Raw writes may need to be split into small chunks if max_raw_write is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently regmap_bulk_write will split a write into chunks before
calling regmap_raw_write if max_raw_write is set. It is more logical
for this handling to be inside regmap_raw_write itself, as this
removes the need to keep re-implementing the chunking code, which
would be the same for all users of regmap_raw_write.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the case were the bulk transaction is split up into smaller chunks
data is passed directly to regmap_raw_write. However regmap_bulk_write
uses data in host endian and regmap_raw_write expects data in device
endian. As such if the host and device differ in endian the wrong data
will be written to the device. Correct this issue using a similar
approach to the single raw write case below it, duplicate the data
into a new buffer and use parse_inplace to format the data correctly.
Fixes: adaac459759d ("regmap: Introduce max_raw_read/write for regmap_bulk_read/write")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regmap-bulk
|
|
This registers regmaps with debugfs even when they do not have an
associated device. For example, this is common for syscon regmaps.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This fixes a possible NULL pointer dereference oops in
regmap_name_read_file() when the regmap does not have a device
associated with it. For example syscon regmaps retrieved with
syscon_regmap_lookup_by_compatible() don't have a device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bulk reads may potentially read a lot of registers and regmap_read will
take and release the regmap lock for each register. Avoid bouncing
the lock so frequently by holding the lock locally and calling
_regmap_read instead. This also has the nice side-effect that all the
reads will be done atomically so no other threads can sneak a write in
during the regmap_bulk_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Raw reads may need to be split into small chunks if max_raw_read is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently regmap_bulk_read will split a read into chunks before
calling regmap_raw_read if max_raw_read is set. It is more logical for
this handling to be inside regmap_raw_read itself, as this removes the
need to keep re-implementing the chunking code, which would be the
same for all users of regmap_raw_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As a helper function exists for calculating register offsets lets use
that rather than open coding with the reg_stride.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A bulk read can be implemented either through regmap_raw_read, or
by reading each register individually using regmap_read. Both
regmap_read and regmap_bulk_read should return values in native
endian. In the individual case the current implementation calls
format_val to put the data into the output array, which can cause
endian issues. The regmap_read will have already converted the data
into native endian, if the hosts endian differs from the device then
format_val will switch the endian back again.
Rather than using format_val simply use the code that is called if
there is no format_val function. This code supports all cases except
24-bit but there don't appear to be any users of regmap_bulk_read for
24-bit. Additionally, it would have to be a big endian host for the
old code to actually function correctly anyway.
Fixes: 15b8d2c41fe5 ("regmap: Fix regmap_bulk_read in BE mode")
Reported-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The cache pointer points to the actual memory used by the cache, as the
comparison here is looking for the type of the cache it should check
against cache_type.
Fixes: 1ea975cf1ef5 ("regmap: Add a function to check if a regmap register is cached")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current implementation is broken for regmaps that have a reg_stride,
since it doesn't take the stride into account. Correct this by using the
helper function to calculate the register offset.
Fixes: f01ee60fffa4 ("regmap: implement register striding")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit message says that we are allowed to read and write up to 32
bytes but the code only allows us to write 31 bytes. In other words,
the ">=" should be changed to ">". But this is already checked in
regmap_raw_read()/write() so we can just remove the if statemetents.
Fixes: 29332534e2b6 ("regmap-i2c: Add smbus i2c block support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We're supposed to be checking that "val_len" is not too large but
instead we check if it is smaller than the max.
The only function affected would be regmap_i2c_smbus_i2c_write() in
drivers/base/regmap/regmap-i2c.c. Strangely that function has its own
limit check which returns an error if (count >= I2C_SMBUS_BLOCK_MAX) so
it doesn't look like it has ever been able to do anything except return
an error.
Fixes: c335931ed9d2 ("regmap: Add raw_write/read checks for max_raw_write/read sizes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
|
|
'regmap/topic/zero' into regmap-next
|
|
'regmap/topic/hwspinlock' and 'regmap/topic/nolock' into regmap-next
|
|
All zero read and write masks in the regmap config are used to signal no
special mask is needed and the bus defaults are used. In some devices
all zero read/write masks are the special mask and bus defaults should
not be used. To signal this a new variable is added.
For example SPI often sets bit 7 in address to signal to the device a
read is requested. On TI AFE44xx parts with SPI interfaces no bit
needs to be set as registers are either read or write only and the
operation can be determined from the address only. For this case both
masks must be zero to not effect the address.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This makes the code slightly more readable and allows for cleaner
addition of functionality in later patches.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SoundWire bus provides sdw_read() and sdw_write() APIs for Slave
devices to program the registers. Provide support in regmap for
SoundWire bus.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is a follow-up to commit a5ba91c380b8 ("regmap: debugfs: emit a
debug message when locking is disabled"). I figured that a user may
see this message, grep the code, come to this place and he still won't
know why we actually disabled debugfs.
Add a comment explaining the reason.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We currently silently omit creating the debugfs entries when regmap
locking is disabled. Users may not be aware of the reason for which
regmap files don't show up in debugfs. Add a dev_dbg() message
explaining that.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The map->work_buf is a buffer preallocated in __regmap_init() with size
allowing it to store all 3 parts of a buffer - reg, pad and val. While
reg and val parts are always properly setup before each transaction, the
pad part is left at its default value (zeros). Until it is overwritten,
that is.
_regmap_bus_read(), when calling _regmap_raw_read() uses beginning of
work_buf as a place to store data read. Usually that is fine but if
val_bits > reg_bits && pad_bits > 0, padding area of work_buf() may get
overwritten. Since padding is not zeroed before each transaction,
garbage will be used on next calls.
This patch moves the val pointer used for _regmap_raw_read() to point
to a part of work_buf intended for storing value read.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support to read/write SLIMbus value elements.
Currently it only supports byte read/write. Adding this support in
regmap would give codec drivers more flexibility when there are more
than 2 control interfaces like SLIMbus, i2c.
Without this patch each codec driver has to directly call SLIMbus value
element apis, and this could would get messy once we want to add i2c
interface to it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently we just copy over the pointer passed to regmap_init() in
the regmap config struct. To be on the safe side: duplicate the string
with kstrdup_const() so that if an unaware user passes an address to
a stack-allocated buffer, we won't crash.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regmap-const
|
|
The recently added support for disabling the regmap internal locking left
debugfs enabled for devices with the locking disabled. This is a problem
since debugfs allows userspace to do things like initiate reads from the
hardware which will use the scratch buffers protected by the regmap locking
so could cause data corruption.
For safety address this by just disabling debugfs for these devices. That
is overly conservative since some of the debugfs files just read internal
data structures but it's much simpler to implmement and less likely to
lead to problems with tooling that works with debugfs.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Minor naming convention tweak.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
