| Age | Commit message (Collapse) | Author |
|---|
|
Add a helper to change the owner of a device's power entries. This
needs to happen when the ownership of a device is changed, e.g. when
moving network devices between network namespaces.
This function will be used to correctly account for ownership changes,
e.g. when moving network devices between network namespaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The power.h is a bit messy due to the various existing CONFIG_PM* Kconfig
combinations. However the final section for wakeup_source_sysfs*() can be
moved inside one of the existing sections rather than adding yet another
one, so let's do that to clean up the code a little bit.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The device_set_wakeup_enable() function can be called on a device that
hasn't been registered with device_add() yet. This allows the device to
be in a state where wakeup is enabled for it but the device isn't
published to userspace in sysfs yet.
After commit c8377adfa781 ("PM / wakeup: Show wakeup sources stats in
sysfs"), calling device_set_wakeup_enable() will fail for a device that
hasn't been registered with the driver core via device_add(). This is
because we try to create sysfs entries for the device and associate a
wakeup class kobject with it before the device has been registered.
Let's follow a similar approach that device_set_wakeup_capable() takes
here and register the wakeup class either from
device_set_wakeup_enable() when the device is already registered, or
from dpm_sysfs_add() when the device is being registered with the driver
core via device_add().
Fixes: c8377adfa781 ("PM / wakeup: Show wakeup sources stats in sysfs")
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tri Vo <trong@android.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add an ID and a device pointer to 'struct wakeup_source'. Use them to to
expose wakeup sources statistics in sysfs under
/sys/class/wakeup/wakeup<ID>/*.
Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tri Vo <trong@android.com>
Tested-by: Kalesh Singh <kaleshsingh@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In a step to consolidate the code for fetching the PM-runtime
active/suspended time for a device, add a common function for that
and make the existing pm_runtime_suspended_time() call it.
Also add a corresponding pm_runtime_active_time() calling the new
common function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Changelog, function rename ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The inline versions of rpm_sysfs_remove() and wakeup_sysfs_add|remove(),
are not being used while CONFIG_PM is unset, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The functions pm_qos_sysfs_add|remove() are available as inline functions
only while CONFIG_PM is unset, but are not being used. Likely they are a
leftover from an earlier cleanup in the past, anyway let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The inline versions of dev_pm_arm|disarm_wake_irq() and
dev_pm_enable|disable_wake_irq_check() are not being used while CONFIG_PM
is unset, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The inline versions of device_wakeup_arm|disarm_wake_irqs(), which are
available while when CONFIG_PM is set and CONFIG_PM_SLEEP unset, are not
being used, hence let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This makes it easy to grep :wakeup /proc/interrupts.
Suggested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Returning an error code from dev_pm_attach_wake_irq() if
device_wakeup_attach_irq() called by it returns an error is
pointless, because the wakeup source used by it may be deleted
by user space via sysfs at any time and in particular right after
dev_pm_attach_wake_irq() has returned. Moreover, it requires
the callers of dev_pm_attach_wake_irq() to create that wakeup
source via device_wakeup_enable() upfront, but that obviously is
racy with respect to the sysfs-based manipulations of it.
To avoid the race, modify device_wakeup_attach_irq() to check
that the wakeup source it is going to use is there (and return
early otherwise), make it void (as it cannot fail after that
change) and make dev_pm_attach_wake_irq() simply call it for
the device unconditionally.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the new driver core patches for 4.10-rc1.
Big thing here is the nice addition of "functional dependencies" to
the driver core. The idea has been talked about for a very long time,
great job to Rafael for stepping up and implementing it. It's been
tested for longer than the 4.9-rc1 date, we held off on merging it
earlier in order to feel more comfortable about it.
Other than that, it's just a handful of small other patches, some good
cleanups to the mess that is the firmware class code, and we have a
test driver for the deferred probe logic.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (30 commits)
firmware: Correct handling of fw_state_wait() return value
driver core: Silence device links sphinx warning
firmware: remove warning at documentation generation time
drivers: base: dma-mapping: Fix typo in dmam_alloc_non_coherent comments
driver core: test_async: fix up typo found by 0-day
firmware: move fw_state_is_done() into UHM section
firmware: do not use fw_lock for fw_state protection
firmware: drop bit ops in favor of simple state machine
firmware: refactor loading status
firmware: fix usermode helper fallback loading
driver core: firmware_class: convert to use class_groups
driver core: devcoredump: convert to use class_groups
driver core: class: add class_groups support
kernfs: Declare two local data structures static
driver-core: fix platform_no_drv_owner.cocci warnings
drivers/base/memory.c: Remove unused 'first_page' variable
driver core: add CLASS_ATTR_WO()
drivers: base: cacheinfo: support DT overrides for cache properties
drivers: base: cacheinfo: add pr_fmt logging
drivers: base: cacheinfo: fix boot error message when acpi is enabled
...
|
|
I noticed some wakeirq flakeyness with consumer drivers not using
autosuspend. For drivers not using autosuspend, the wakeirq may never
get unmasked in rpm_suspend() because of irq desc->depth.
We are configuring dedicated wakeirqs to start with IRQ_NOAUTOEN as we
naturally don't want them running until rpm_suspend() is called.
However, when a consumer driver initially calls pm_runtime_get(), we
now wrongly start with disable_irq_nosync() call on the dedicated
wakeirq that is disabled to start with.
This causes desc->depth to toggle between 1 and 2 instead of the usual
0 and 1. This can prevent enable_irq() from unmasking the wakeirq as
that only happens at desc->depth 1.
This does not necessarily show up with drivers using autosuspend as
there is time for disable_irq_nosync() before rpm_suspend() gets called
after the autosuspend timeout.
Let's fix the issue by adding wirq->status that lazily gets set on
the first rpm_suspend(). We also need PM runtime core private functions
for dev_pm_enable_wake_irq_check() and dev_pm_disable_wake_irq_check()
so we can enable the dedicated wakeirq on the first rpm_suspend().
While at it, let's also fix the comments for dev_pm_enable_wake_irq()
and dev_pm_disable_wake_irq(). Those can still be used by the consumer
drivers as needed because the IRQ core manages the interrupt usecount
for us.
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently, there is a problem with taking functional dependencies
between devices into account.
What I mean by a "functional dependency" is when the driver of device
B needs device A to be functional and (generally) its driver to be
present in order to work properly. This has certain consequences
for power management (suspend/resume and runtime PM ordering) and
shutdown ordering of these devices. In general, it also implies that
the driver of A needs to be working for B to be probed successfully
and it cannot be unbound from the device before the B's driver.
Support for representing those functional dependencies between
devices is added here to allow the driver core to track them and act
on them in certain cases where applicable.
The argument for doing that in the driver core is that there are
quite a few distinct use cases involving device dependencies, they
are relatively hard to get right in a driver (if one wants to
address all of them properly) and it only gets worse if multiplied
by the number of drivers potentially needing to do it. Morever, at
least one case (asynchronous system suspend/resume) cannot be handled
in a single driver at all, because it requires the driver of A to
wait for B to suspend (during system suspend) and the driver of B to
wait for A to resume (during system resume).
For this reason, represent dependencies between devices as "links",
with the help of struct device_link objects each containing pointers
to the "linked" devices, a list node for each of them, status
information, flags, and an RCU head for synchronization.
Also add two new list heads, representing the lists of links to the
devices that depend on the given one (consumers) and to the devices
depended on by it (suppliers), and a "driver presence status" field
(needed for figuring out initial states of device links) to struct
device.
The entire data structure consisting of all of the lists of link
objects for all devices is protected by a mutex (for link object
addition/removal and for list walks during device driver probing
and removal) and by SRCU (for list walking in other case that will
be introduced by subsequent change sets). If CONFIG_SRCU is not
selected, however, an rwsem is used for protecting the entire data
structure.
In addition, each link object has an internal status field whose
value reflects whether or not drivers are bound to the devices
pointed to by the link or probing/removal of their drivers is in
progress etc. That field is only modified under the device links
mutex, but it may be read outside of it in some cases (introduced by
subsequent change sets), so modifications of it are annotated with
WRITE_ONCE().
New links are added by calling device_link_add() which takes three
arguments: pointers to the devices in question and flags. In
particular, if DL_FLAG_STATELESS is set in the flags, the link status
is not to be taken into account for this link and the driver core
will not manage it. In turn, if DL_FLAG_AUTOREMOVE is set in the
flags, the driver core will remove the link automatically when the
consumer device driver unbinds from it.
One of the actions carried out by device_link_add() is to reorder
the lists used for device shutdown and system suspend/resume to
put the consumer device along with all of its children and all of
its consumers (and so on, recursively) to the ends of those lists
in order to ensure the right ordering between all of the supplier
and consumer devices.
For this reason, it is not possible to create a link between two
devices if the would-be supplier device already depends on the
would-be consumer device as either a direct descendant of it or a
consumer of one of its direct descendants or one of its consumers
and so on.
There are two types of link objects, persistent and non-persistent.
The persistent ones stay around until one of the target devices is
deleted, while the non-persistent ones are removed automatically when
the consumer driver unbinds from its device (ie. they are assumed to
be valid only as long as the consumer device has a driver bound to
it). Persistent links are created by default and non-persistent
links are created when the DL_FLAG_AUTOREMOVE flag is passed
to device_link_add().
Both persistent and non-persistent device links can be deleted
with an explicit call to device_link_del().
Links created without the DL_FLAG_STATELESS flag set are managed
by the driver core using a simple state machine. There are 5 states
each link can be in: DORMANT (unused), AVAILABLE (the supplier driver
is present and functional), CONSUMER_PROBE (the consumer driver is
probing), ACTIVE (both supplier and consumer drivers are present and
functional), and SUPPLIER_UNBIND (the supplier driver is unbinding).
The driver core updates the link state automatically depending on
what happens to the linked devices and for each link state specific
actions are taken in addition to that.
For example, if the supplier driver unbinds from its device, the
driver core will also unbind the drivers of all of its consumers
automatically under the assumption that they cannot function
properly without the supplier. Analogously, the driver core will
only allow the consumer driver to bind to its device if the
supplier driver is present and functional (ie. the link is in
the AVAILABLE state). If that's not the case, it will rely on
the existing deferred probing mechanism to wait for the supplier
driver to become available.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a suitable prepare callback cannot be found for a given device and
its driver has no PM callbacks at all, assume that it can go direct to
complete when the system goes to sleep.
The reason for this is that there's lots of devices in a system that do
no PM at all and there's no reason for them to prevent their ancestors
to do direct_complete if they can support it.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are two common expectations among several subsystems/drivers that
deploys runtime PM support, but which isn't met by the driver core.
Expectation 1)
At ->probe() the subsystem/driver expects the runtime PM status of the
device to be RPM_SUSPENDED, which is the initial status being assigned at
device registration.
This expectation is especially common among some of those subsystems/
drivers that manages devices with an attached PM domain, as those requires
the ->runtime_resume() callback at the PM domain level to be invoked
during ->probe().
Moreover these subsystems/drivers entirely relies on runtime PM resources
being managed at the PM domain level, thus don't implement their own set
of runtime PM callbacks.
These are two scenarios that suffers from this unmet expectation.
i) A failed ->probe() sequence requests probe deferral:
->probe()
...
pm_runtime_enable()
pm_runtime_get_sync()
...
err:
pm_runtime_put()
pm_runtime_disable()
...
As there are no guarantees that such sequence turns the runtime PM status
of the device into RPM_SUSPENDED, the re-trying ->probe() may start with
the status in RPM_ACTIVE.
In such case the runtime PM core won't invoke the ->runtime_resume()
callback because of a pm_runtime_get_sync(), as it considers the device to
be already runtime resumed.
ii) A driver re-bind sequence:
At driver unbind, the subsystem/driver's >remove() callback invokes a
sequence of runtime PM APIs, to undo actions during ->probe() and to put
the device into low power state.
->remove()
...
pm_runtime_put()
pm_runtime_disable()
...
Similar as in the failing ->probe() case, this sequence don't guarantee
the runtime PM status of the device to turn into RPM_SUSPENDED.
Trying to re-bind the driver thus causes the same issue as when re-trying
->probe(), in the probe deferral scenario.
Expectation 2)
Drivers that invokes the pm_runtime_irq_safe() API during ->probe(),
triggers the runtime PM core to increase the usage count for the device's
parent and permanently make it runtime resumed.
The usage count is only dropped at device removal, which also allows it to
be runtime suspended again.
A re-trying ->probe() repeats the call to pm_runtime_irq_safe() and thus
once more triggers the usage count of the device's parent to be increased.
This leads to not only an imbalance issue of the usage count of the
device's parent, but also to keep it runtime resumed permanently even if
->probe() fails.
To address these issues, let's change the policy of the driver core to
meet these expectations. More precisely, at ->probe() failures and driver
unbind, restore the initial states of runtime PM.
Although to still allow subsystem's to control PM for devices that doesn't
->probe() successfully, don't restore the initial states unless runtime PM
is disabled.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Typically when a device is created the bus core it belongs to (for example
PCI) does not know if the device supports things like latency tolerance.
This is left to the driver that binds to the device in question. However,
at that time the device has already been created and there is no way to set
its dev->power.set_latency_tolerance anymore.
So follow what has been done for other PM QoS attributes as well and allow
drivers to expose and hide latency tolerance from userspace, if the device
supports it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Turns out we can automate the handling for the device_may_wakeup()
quite a bit by using the kernel wakeup source list as suggested
by Rafael J. Wysocki <rjw@rjwysocki.net>.
And as some hardware has separate dedicated wake-up interrupt
in addition to the IO interrupt, we can automate the handling by
adding a generic threaded interrupt handler that just calls the
device PM runtime to wake up the device.
This allows dropping code from device drivers as we currently
are doing it in multiple ways, and often wrong.
For most drivers, we should be able to drop the following
boilerplate code from runtime_suspend and runtime_resume
functions:
...
device_init_wakeup(dev, true);
...
if (device_may_wakeup(dev))
enable_irq_wake(irq);
...
if (device_may_wakeup(dev))
disable_irq_wake(irq);
...
device_init_wakeup(dev, false);
...
We can replace it with just the following init and exit
time code:
...
device_init_wakeup(dev, true);
dev_pm_set_wake_irq(dev, irq);
...
dev_pm_clear_wake_irq(dev);
device_init_wakeup(dev, false);
...
And for hardware with dedicated wake-up interrupts:
...
device_init_wakeup(dev, true);
dev_pm_set_dedicated_wake_irq(dev, irq);
...
dev_pm_clear_wake_irq(dev);
device_init_wakeup(dev, false);
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM or even may be dropped entirely in some cases.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PM core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rename symbols, variables, functions and structure fields related do
the resume latency device PM QoS type so that it is clear where they
belong (in particular, to avoid confusion with the latency tolerance
device PM QoS type introduced by a subsequent changeset).
Update the PM QoS documentation to better reflect its current state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Device PM QoS sysfs attributes, if present during device removal,
are removed from within device_pm_remove(), which is too late,
since dpm_sysfs_remove() has already removed the whole attribute
group they belonged to. However, moving the removal of those
attributes to dpm_sysfs_remove() alone is not sufficient, because
in theory they still can be re-added right after being removed by it
(the device's driver is still bound to it at that point).
For this reason, move the entire desctruction of device PM QoS
constraints to dpm_sysfs_remove() and make it prevent any new
constraints from being added after it has run. Also, move the
initialization of the power.qos field in struct device to
device_pm_init_common() and drop the no longer needed
dev_pm_qos_constraints_init().
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Define two device PM QoS flags, PM_QOS_FLAG_NO_POWER_OFF
and PM_QOS_FLAG_REMOTE_WAKEUP, and introduce routines
dev_pm_qos_expose_flags() and dev_pm_qos_hide_flags() allowing the
caller to expose those two flags to user space or to hide them
from it, respectively.
After the flags have been exposed, user space will see two
additional sysfs attributes, pm_qos_no_power_off and
pm_qos_remote_wakeup, under the device's /sys/devices/.../power/
directory. Then, writing 1 to one of them will update the
PM QoS flags request owned by user space so that the corresponding
flag is requested to be set. In turn, writing 0 to one of them
will cause the corresponding flag in the user space's request to
be cleared (however, the owners of the other PM QoS flags requests
for the same device may still request the flag to be set and it
may be effectively set even if user space doesn't request that).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Acked-by: mark gross <markgross@thegnar.org>
|
|
Runtime PM helper functions, like pm_runtime_get_sync(), cannot be
called by early platform device drivers, because the devices' power
management locks are not initialized at that time. This is quite
inconvenient, so modify early_platform_add_devices() to initialize
the devices power management locks as appropriate and make sure that
they won't be initialized more than once if an early platform
device is going to be used as a regular one later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Make the device power management initialization more straightforward
by moving the initialization of common (i.e. used by both runtime PM
and system suspend) fields to a separate routine.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
A runtime suspend of a device (e.g. an MMC controller) belonging to
a power domain or, in a more complicated scenario, a runtime suspend
of another device in the same power domain, may cause power to be
removed from the entire domain. In that case, the amount of time
necessary to runtime-resume the given device (e.g. the MMC
controller) is often substantially greater than the time needed to
run its driver's runtime resume callback. That may hurt performance
in some situations, because user data may need to wait for the
device to become operational, so we should make it possible to
prevent that from happening.
For this reason, introduce a new sysfs attribute for devices,
power/pm_qos_resume_latency_us, allowing user space to specify the
upper bound of the time necessary to bring the (runtime-suspended)
device up after the resume of it has been requested. However, make
that attribute appear only for the devices whose drivers declare
support for it by calling the (new) dev_pm_qos_expose_latency_limit()
helper function with the appropriate initial value of the attribute.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To read the current PM QoS value for a given device we need to
make sure that the device's power.constraints object won't be
removed while we're doing that. For this reason, put the
operation under dev->power.lock and acquire the lock
around the initialization and removal of power.constraints.
Moreover, since we're using the value of power.constraints to
determine whether or not the object is present, the
power.constraints_state field isn't necessary any more and may be
removed. However, dev_pm_qos_add_request() needs to check if the
device is being removed from the system before allocating a new
PM QoS constraints object for it, so make it use the
power.power_state field of struct device for this purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Currently, wakeup sysfs attributes are created for all devices,
regardless of whether or not they are wakeup-capable. This is
excessive and complicates wakeup device identification from user
space (i.e. to identify wakeup-capable devices user space has to read
/sys/devices/.../power/wakeup for all devices and see if they are not
empty).
Fix this issue by avoiding to create wakeup sysfs files for devices
that cannot wake up the system from sleep states (i.e. whose
power.can_wakeup flags are unset during registration) and modify
device_set_wakeup_capable() so that it adds (or removes) the relevant
sysfs attributes if a device's wakeup capability status is changed.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Some devices, such as USB interfaces, cannot be power-managed
independently of their parents, i.e., they cannot be put in low power
while the parent remains at full power. This patch (as1425) creates a
new "no_callbacks" flag, which tells the PM core not to invoke the
runtime-PM callback routines for the such devices but instead to
assume that the callbacks always succeed. In addition, the
non-debugging runtime-PM sysfs attributes for the devices are removed,
since they are pretty much meaningless.
The advantage of this scheme comes not so much from avoiding the
callbacks themselves, but rather from the fact that without the need
for a process context in which to run the callbacks, more work can be
done in interrupt context.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Introduce struct wakeup_source for representing system wakeup sources
within the kernel and for collecting statistics related to them.
Make the recently introduced helper functions pm_wakeup_event(),
pm_stay_awake() and pm_relax() use struct wakeup_source objects
internally, so that wakeup statistics associated with wakeup devices
can be collected and reported in a consistent way (the definition of
pm_relax() is changed, which is harmless, because this function is
not called directly by anyone yet). Introduce new wakeup-related
sysfs device attributes in /sys/devices/.../power for reporting the
device wakeup statistics.
Change the global wakeup events counters event_count and
events_in_progress into atomic variables, so that it is not necessary
to acquire a global spinlock in pm_wakeup_event(), pm_stay_awake()
and pm_relax(), which should allow us to avoid lock contention in
these functions on SMP systems with many wakeup devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add sysfs attribute /sys/power/pm_async allowing the user space to
disable/enable asynchronous suspend/resume of devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Introduce a core framework for run-time power management of I/O
devices. Add device run-time PM fields to 'struct dev_pm_info'
and device run-time PM callbacks to 'struct dev_pm_ops'. Introduce
a run-time PM workqueue and define some device run-time PM helper
functions at the core level. Document all these things.
Special thanks to Alan Stern for his help with the design and
multiple detailed reviews of the pereceding versions of this patch
and to Magnus Damm for testing feedback.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@igel.co.jp>
|
|
dpm_list currently relies on the fact that child devices will
be registered after their parents to get a correct suspend
order. Using device_move() however destroys this assumption, as
an already registered device may be moved under a newly registered
one.
This patch adds a new argument to device_move(), allowing callers
to specify how dpm_list should be adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
is set
This patch (as1124) fixes a couple of bugs in the PM core. The new
dev->power.status field should be initialized regardless of whether
CONFIG_PM_SLEEP is enabled, and similarly dpm_sysfs_add() should be
called whenever CONFIG_PM is enabled.
The patch separates out the call to dpm_sysfs_add() from the call to
device_pm_add(). As a result device_pm_add() can no longer return an
error, so its return type is changed to void.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Romit Dasgupta <romit@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Introduce 'struct pm_ops' and 'struct pm_ext_ops' ('ext' meaning
'extended') representing suspend and hibernation operations for bus
types, device classes, device types and device drivers.
Modify the PM core to use 'struct pm_ops' and 'struct pm_ext_ops'
objects, if defined, instead of the ->suspend(), ->resume(),
->suspend_late(), and ->resume_early() callbacks (the old callbacks
will be considered as legacy and gradually phased out).
The main purpose of doing this is to separate suspend (aka S2RAM and
standby) callbacks from hibernation callbacks in such a way that the
new callbacks won't take arguments and the semantics of each of them
will be clearly specified. This has been requested for multiple
times by many people, including Linus himself, and the reason is that
within the current scheme if ->resume() is called, for example, it's
difficult to say why it's been called (ie. is it a resume from RAM or
from hibernation or a suspend/hibernation failure etc.?).
The second purpose is to make the suspend/hibernation callbacks more
flexible so that device drivers can handle more than they can within
the current scheme. For example, some drivers may need to prevent
new children of the device from being registered before their
->suspend() callbacks are executed or they may want to carry out some
operations requiring the availability of some other devices, not
directly bound via the parent-child relationship, in order to prepare
for the execution of ->suspend(), etc.
Ultimately, we'd like to stop using the freezing of tasks for suspend
and therefore the drivers' suspend/hibernation code will have to take
care of the handling of the user space during suspend/hibernation.
That, in turn, would be difficult within the current scheme, without
the new ->prepare() and ->complete() callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Modify the PM core to protect its data structures, specifically the
dpm_active list, from being corrupted if a child of the currently
suspending device is registered concurrently with its ->suspend()
callback. In that case, since the new device (the child) is added
to dpm_active after its parent, the PM core will attempt to
suspend it after the parent, which is wrong.
Introduce a new member of struct dev_pm_info, called 'sleeping',
and use it to check if the parent of the device being added to
dpm_active has been suspended, in which case the device registration
fails. Also, use 'sleeping' for checking if the ordering of devices
on dpm_active is correct.
Introduce variable 'all_sleeping' that will be set to 'true' once all
devices have been suspended and make new device registrations fail
until 'all_sleeping' is reset to 'false', in order to avoid having
unsuspended devices around while the system is going into a sleep state.
Remove pm_sleep_rwsem which is not necessary any more.
Special thanks to Alan Stern for discussions and suggestions that
lead to the creation of this patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Move the declaration of device_pm_schedule_removal() to device.h
and make it exported, as it will be used directly by some drivers
for unregistering device objects during suspend/resume cycles in a
safe way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
shutdown.c had some stuff it did not need, including a duplicate extern
in the power.h file. This cleans up all of that.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch reorganizes the way suspend and resume notifications are
sent to drivers. The major changes are that now the PM core acquires
every device semaphore before calling the methods, and calls to
device_add() during suspends will fail, while calls to device_del()
during suspends will block.
It also provides a way to safely remove a suspended device with the
help of the PM core, by using the device_pm_schedule_removal() callback
introduced specifically for this purpose, and updates two drivers (msr
and cpuid) that need to use it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The CONFIG_SUSPEND changes in 2.6.23 caused a regression under certain
configuration conditions (SUSPEND=n, USB_AUTOSUSPEND=y) where all USB
device attributes in sysfs (idVendor, idProduct, ...) silently disappeared,
causing udev breakage and more.
The cause of this is that the /sys/.../power subdirectory is now only
created when CONFIG_PM_SLEEP is set, however, it should be created whenever
CONFIG_PM is set to handle the above situation. The following patch fixes
the regression.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as993) merges the suspend.c and resume.c files in
drivers/base/power into main.c, making some public symbols private.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
suspend_device() and resume_device() can now become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.
Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.
Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.
The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).
There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch (as933) removes the deprecated dpm_runtime_suspend() and
dpm_runtime_resume() routines from the PM core. The only user of
those routines is the PCMCIA ds driver; local replacements are added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Power Management code uses semaphores as mutexes. Use the mutex API
instead of the (binary) semaphores.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
With CONFIG_PM=n:
drivers/built-in.o(.text+0x1098c): In function `hub_thread':
drivers/usb/core/hub.c:2673: undefined reference to `.dpm_runtime_resume'
drivers/built-in.o(.text+0x10998):drivers/usb/core/hub.c:2674: undefined reference to `.dpm_runtime_resume'
Please, never ever ever put extern decls into .c files. Use the darn header
files :(
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The driver model has a "detach_state" mechanism that:
- Has never been used by any in-kernel drive;
- Is superfluous, since driver remove() methods can do the same thing;
- Became buggy when the suspend() parameter changed semantics and type;
- Could self-deadlock when called from certain suspend contexts;
- Is effectively wasted documentation, object code, and headspace.
This removes that "detach_state" mechanism; net code shrink, as well
as a per-device saving in the driver model and sysfs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
