| Age | Commit message (Collapse) | Author |
|---|
|
vt6420 completely loses its ability to raise IRQ for ATAPI devices if
ATA_NIEN is diddled with in ->freeze. Further investigation is
necessary to determine whether this problem is shared on other
controllers but it doesn't seem to be at this point.
Make vt6420's ->freeze only clear IRQ to fix this problem. This makes
vt6420 relatively more prone to IRQ storms but the controller is way
too braindamaged to worry about that anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When set_mode() changed ->set_mode didn't adapt. This makes the needed
changes and removes the relevant FIXME case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Rather than ending up with two layers of negation jut rename the variable
and lose one.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fixup the inialization of qc->n_elem. It currently gets
initialized to 1 for commands that do not transfer any data.
Fix this by initializing n_elem to 0 and only setting to 1
in ata_scsi_qc_new when there is data to transfer. This fixes
some problems seen with SATA devices attached to ipr adapters.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some ATA/ATAPI devices act weirdly after the link is put into slumber
mode. Some hang completely requiring physical power removal while
others fail to wake up till the link is hardreset a couple of times.
The addition of slumber on power down was never driven by real need.
It just followed what ahci spec said literally. The spec itself seems
faulty in that it doesn't consider devices (not controllers) which
don't support link powersaving mode.
Theory never matches reality when it comes to dark allys of cheap
ATA/ATAPI world. It's just unrealistic to expect vendors to test
rarely used link powersaving feature rigorously. This patch makes
ahci more friendly to the coldness of reality.
This shouldn't have any negative effect - when suspend operation
succeeds, we power off the whole machine; otherwise, we wake up
everything. I can't see any reason to be so elaborate with powering
down the link in the first place.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Several people reported issues with certain drive commands timing out on
sata_nv controllers running in ADMA mode. The commands in question were
non-DMA-mapped commands, usually FLUSH CACHE or FLUSH CACHE EXT.
From experimentation it appears that the NV_INT_DEV indication isn't
always set when a legitimate command completion interrupt is received on
a legacy-mode command, at least not on these controllers in ADMA mode.
When a command is pending on the port, force the flag on always in the
irq_stat value before calling nv_host_intr so that the drive busy state
is always checked by ata_host_intr.
This also fixes some questionable code in nv_host_intr which called
ata_check_status when a command was pending and ata_host_intr returned
"unhandled". If the device interrupted at just the wrong time this could
cause interrupts to be lost.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
As with JMicron controllers, ULi M5288 sets interface fatal error bit
on device error including ATAPI CC. This makes libata hardreset the
port on ATAPI CC thus making it impossible to use. Ignore interface
fatal error bit on ULi M5288. This fixes bugzilla bug #7837.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
With the following patch, my HighPoint 2310 with a Marvell 88SX7042 on
it seems to work OK.
The controller only has 4 ports, with MV_FLAG_DUAL_HC it seems to init 8
ports and fails miserably at probe time. There are no other devices mapped
to that chip, maybe it was just incorrectly specified in the first place?
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
libata EH ignores port-wide actions in per-dev action mask. However,
device resume requests EH_SOFTRESET using per-dev action mask. Under
certain circumstances, this results in not resetting frozen port after
resuming which causes failure of all commands.
This patch allows port-wide actions to be requested in per-dev action
mask. Before EH recovery starts, port-wide actions will be collected.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add PCI ID 0x5337 to supported PCI ID. This is VT8237 in IDE mode.
Signed-off-by: Luca Pedrielli <luca.pedrielli@barradev.it>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The HPT37x driver very carefully handles DMA completions and the needed
fixups are done on pci registers 0x50 and 0x52. This is unfortunate
because the actual registers are 0x50 and 0x54. Fixing this offset cures
the second channel problems reported.
Secondly there are some problems with the HPT370 and certain ATA drives.
The filter code however only filters ATAPI devices due to a reversed type
check.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This is a slight variant on the patch I posted December 16th to fix
libata combined mode handling. The only real change is that we now
correctly also reserve BAR1,2,4. That is basically a neatness issue.
Jeff was unhappy about two things
1. That it didn't work in the case of one channel native one channel
legacy.
This is a silly complaint because the SFF layer in libata doesn't handle
this case yet anyway.
2. The case where combined mode is in use and IDE=n.
In this case the libata quirk code reserves the resources in question
correctly already.
Once the combined mode stuff is redone properly (2.6.21) then the entire
mess turns into a single pci_request_regions() for all cases and all the
ugly resource hackery goes away.
I'm sending this now rather than after running full test suites so that
it can get the maximal testing in a short time. I'll be running tests on
this after lunch.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Acked-by: Theodore Tso <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Now that iomap merge is close to reality, and since the warnings and
issue have been around so long, we don't need a reminder on every build
that libata needs to be converted over to iomap.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
libata depended on SCSI command to have the correct length when
tranlating it into an ATA command. This generally worked for commands
issued by SCSI HLD but user could issue arbitrary broken command using
sg interface.
Also, when building ATAPI command, full command size was always
copied. Because some ATAPI devices needs bytes after CDB cleared, if
upper layer doesn't clear bytes after CDB, such devices will
malfunction. This necessiated recent clear-garbage-after-CDB fix in
sg interfaces. However, scsi_execute() isn't fixed yet and HL-DT-ST
DVD-RAM GSA-H30N malfunctions on initialization commands issued from
SCSI.
This patch makes xlat functions always consider SCSI cmd_len. Each
translation function checks for proper cmd_len and ATAPI translaation
clears bytes after CDB.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
xlat function will be updated to consider qc->scsicmd->cmd_len and
many xlat functions deference qc->scsicmd already. It doesn't make
sense to pass qc->scsicmd->cmnd as @cdb separately. Kill the
argument.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Variable names in xlat functions are quite confusing now. 'scsicmd'
is used for CDB while qc->scsicmd points to struct scsi_cmnd while
'cmd' is used for struct scsi_cmnd.
This patch cleans up variable names in xlat functions such that 'scmd'
is used for struct scsi_cmnd and 'cdb' for CDB. Also, 'scmd' local
variable is added if qc->scsicmd is used multiple times.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The content of memory map io of BAR5 have been change from MCP65 then
sata_nv can't work fine on the platform based on MCP65 and MCP67, so move
their IDs from sata_nv.c to ahci.c.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make this array static so it doesn't have to be built at runtime.
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
side-effectful-expression-within-assert give me the creeps.
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The UDMA66 VIA hardware has no controller side cable detect bits we can
use. This patch minimally fixes the problem by reporting unknown in this
case and using drive side detection.
The old drivers/ide code does some additional tricks but those aren't
appropriate now we are in -rc.
Without this update UDMA66 via controllers run slowly. They don't fail so
it's a borderline call whether this is -rc material or not.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
> Thanks for clarifying Bill, and sorry Alan. ata_piix does indeed work
> correctly. The help text is a bit confusing:
>
> config ATA_PIIX
> tristate "Intel PIIX/ICH SATA support"
> depends on PCI
> help
> This option enables support for ICH5/6/7/8 Serial ATA.
> If PATA support was enabled previously, this enables
> support for select Intel PIIX/ICH PATA host controllers.
New help text
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This removes the extra definition of the .error_handler member
in the pata_rz1000 driver.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The return value of platform_device_register_simple() should be checked
by IS_ERR().
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Do not mangle with HOST_CAP while resetting controller. The code is
there for a historical reason. The mangling breaks controller feature
detection and 0 PORTS_IMPL workaround code.
This problem was spotted by Manoj Kasichainula.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Manoj Kasichainula <manoj@io.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Calling sg_init_one() with NULL buf causes oops on certain
configurations. Don't initialize sg in ata_exec_internal() if
DMA_NONE and make the function complain if @buf is NULL when dma_dir
isn't DMA_NONE. While at it, fix comment.
The problem is discovered and initial patch was submitted by Arnd
Bergmann.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Current Broadcom/Serverworks SATA boards (including Apple K2 SATA)
have problems with ATAPI DMA, so it is disabled. ATAPI PIO, ATA PIO,
and ATA DMA continue to work just fine.
Acked-by: Anantha Subramanyam <ananth@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
We are inside spin_lock_irqsave(). quoth akpm's debug facility:
[ 231.948000] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
[ 232.232000] ata1.00: configured for UDMA/33
[ 232.404000] WARNING (1) at arch/i386/mm/highmem.c:47 kmap_atomic()
[ 232.404000] [<c01162e6>] kmap_atomic+0xa9/0x1ab
[ 232.404000] [<c0242c81>] ata_scsi_rbuf_get+0x1c/0x30
[ 232.404000] [<c0242caf>] ata_scsi_rbuf_fill+0x1a/0x87
[ 232.404000] [<c0243ab2>] ata_scsiop_mode_sense+0x0/0x309
[ 232.404000] [<c01729d5>] end_bio_bh_io_sync+0x0/0x37
[ 232.404000] [<c02311c6>] scsi_done+0x0/0x16
[ 232.404000] [<c02311c6>] scsi_done+0x0/0x16
[ 232.404000] [<c0242dcc>] ata_scsi_simulate+0xb0/0x13f
[...]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
piix_init_one() allocates host private data which should be freed by
piix_host_stop(). ich_pata_ops wasn't converted to piix_host_stop()
while merging, leaking 4 bytes on driver detach. Fix it.
This was spotted using Kmemleak by Catalin Marinas.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Catalin Marinas <catalin.marinas@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This updated patch adds the Intel ICH9 IDE mode SATA controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
All kcalloc() calls of the form "kcalloc(1,...)" are converted to the
equivalent kzalloc() calls, and a few kcalloc() calls with the incorrect
ordering of the first two arguments are fixed.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The ata timing computation code makes some mistakes in PIO5/6 because a
check was not updated correctly when I put this support into the kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch converts sata_promise to use new-style libata error
handling on Promise SATA chips, for both SATA and PATA ports.
* ATA_FLAG_SRST is no longer set
* ->phy_reset is no longer set as it is unused when ->error_handler
is present, and pdc_sata_phy_reset() has been removed
* pdc_freeze() masks interrupts and halts DMA via PDC_CTLSTAT
* pdc_thaw() clears interrupt status in PDC_INT_SEQMASK and then
unmasks interrupts in PDC_CTLSTAT
* pdc_error_handler() reinitialises the port if it isn't frozen,
and then invokes ata_do_eh() with standard {s,}ata reset methods
* pdc_post_internal_cmd() resets the port in case of errors
* the PATA-only 20619 chip continues to use old-style EH:
not by necessity but simply because I don't have documentation
for it or any way to test it
Since the previous version pdc_error_handler() has been rewritten
and it now mostly matches ahci and sata_sil24. In case anyone
wonders: the call to pdc_reset_port() isn't a heavy-duty reset,
it's a light-weight reset to quickly put a port into a sane state.
The discussion about the PCI flushes in pdc_freeze() and pdc_thaw()
seemed to end with a consensus that the flushes are OK and not
obviously redundant, so I decided to keep them for now.
This patch was prepared against 2.6.19-git7, but it also applies
to 2.6.19 + libata #upstream, with or without the revised sata_promise
cleanup patch I recently submitted.
This patch does conflict with the #promise-sata-pata patch:
this patch removes pdc_sata_phy_reset() while #promise-sata-pata
modifies it. The correct patch resolution is to remove the function.
Tested on 2037x and 2057x chips, with PATA patches on top and disks
on both SATA and PATA ports.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Even if ATA_FLAG_PIO_POLLING is set, libata uses irq pio for the ATA_PROT_NODATA protocol.
This patch let ATA_FLAG_PIO_POLLING use polling pio for the ATA_PROT_NODATA protocol.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch performs two simple cleanups of sata_promise.
* Remove board_20771 and map device id 0x3577 to board_2057x.
After the recent corrections for SATAII chips, board_20771 and
board_2057x were equivalent in the driver.
* Remove hp->hotplug_offset and use hp->flags & PDC_FLAG_GEN_II
to compute hotplug_offset in pdc_host_init(). hp->hotplug_offset
was used to distinguish 1st and 2nd generation chips in one
particular case, but now we have that information in a more
general form in hp->flags, so hp->hotplug_offset is redundant.
Changes since previous submission: rebased on libata-dev #upstream,
cleaned up hotplug_offset computation based on Tejun's comments,
expanded hotplug_offset removal rationale.
This patch does not depend on the pending new EH conversion patch.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/pcmcia/ds.c
Fix up merge failures with Linus's head and fix new compile failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.
Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
As we read out the manufactor and card_id from the PCMCIA device in the
PCMCIA core, and device drivers can access those reliably in struct
pcmcia_device's fields manf_id and card_id, remove additional (and partly
broken) manf_id and card_id detection logic from PCMCIA device drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Microdrive reported by one of OpenEmbedded developers.
product info: "WEIDA", "TWTTI", ""
manfid: 0x000a, 0x0000
function: 4 (fixed disk)
(equivalent update to pata_pcmcia.c by Dominik Brodowski)
Signed-off-by: Marcin Juszkiewicz <openembedded@hrw.one.pl>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Add an ID entry for:
product info: "TRANSCEND", "TS1GCF80", "", ""
manfid: 0x000a, 0x0000
function: 4 (fixed disk)
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Switch to pci_get_bus_and_slot because some x86 systems seem to be
handing us a device with dev->bus = NULL. Also don't apply the isa fixup
to revision C6 and later of the chip.
Really we need to work out wtf is handing us pdev->bus = NULL, but firstly
and more importantly we need the drivers working.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds code to fix up the PHYMODE4 "align timing"
register value on second-generation Promise SATA chips.
Failure to correct this value on non-x86 machines makes
drive detection prone to failure due to timeouts. (I've
observed about 50% detection failure rates on SPARC64.)
The HW boots with a bad value in this register, but on x86
machines the Promise BIOS corrects it to the value recommended
by the manual, so most people have been unaffected by this issue.
After developing the patch I checked Promise's SATAII driver,
and discovered that it also corrects PHYMODE4 just like this
patch does.
This patch depends on the sata_promise SATAII updates
patch I sent recently.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
libata switched to IRQ-driven IDENTIFY when IRQ-driven PIO was
introduced. This has caused a lot of problems including device
misdetection and phantom device.
ATA_FLAG_DETECT_POLLING was added recently to selectively use polling
IDENTIFY on problemetic drivers but many controllers and devices are
affected by this problem and trying to adding ATA_FLAG_DETECT_POLLING
for each such case is diffcult and not very rewarding.
This patch makes libata always use polling IDENTIFY. This is
consistent with libata's original behavior and drivers/ide's behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Noticed by Tejun and others.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ahci_init_controller() calls ahci_deinit_port() to make sure the
controller is stopped before initializing the controller. In turn,
ahci_deinit_port() invokes ahci_power_down() to power down the port.
If the controller supports slumber mode, the link is put into it.
Unfortunately, some devices don't implement link powersaving mode
properly and show erratic behavior after link is put into slumber
mode. For example, HL-DT-ST DVD-RAM GSA-H30N completely locks up on
slumber transition and can only be recovered with the *REAL* hard
reset - power removal and reapply.
Note that this makes the first probing reset different from all
others. If the above dvd-ram is hotplugged after ahci is initialized,
no problem occurs because ahci is already fully initialized with phy
powered up. So, this might also be the reason for other weird AHCI
initial probing abnormalities.
This patch moves power up/down out of port init/deinit and call them
only when needed.
Power down is now called only when suspending. As system suspend
usually involves powering down 12v for storage devices, this shouldn't
cause problem even if the attached device doesn't support slumber
mode. However, in partial power management and suspend failure cases,
devices might lock up after suspend attempt. I thought about removing
transition to slumber mode altogether but ahci spec mandates it before
HBA D3 state transition. Blacklisting such devices might be the
solution.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
