| Age | Commit message (Collapse) | Author |
|---|
|
Older ATF does not provide SMC call for SATA phy power on functionality and
therefore initialization of ahci_mvebu is failing when older version of ATF
is using. In this case phy_power_on() function returns -EOPNOTSUPP.
This patch adds a new hflag AHCI_HFLAG_IGN_NOTSUPP_POWER_ON which cause
that ahci_platform_enable_phys() would ignore -EOPNOTSUPP errors from
phy_power_on() call.
It fixes initialization of ahci_mvebu on Espressobin boards where is older
Marvell's Arm Trusted Firmware without SMC call for SATA phy power.
This is regression introduced in commit 8e18c8e58da64 ("arm64: dts: marvell:
armada-3720-espressobin: declare SATA PHY property") where SATA phy was
defined and therefore ahci_platform_enable_phys() on Espressobin started
failing.
Fixes: 8e18c8e58da64 ("arm64: dts: marvell: armada-3720-espressobin: declare SATA PHY property")
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Cc: <stable@vger.kernel.org> # 5.1+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A feature has been added in the libahci driver: the possibility to set
a new flag in hpriv->flags to let the core handle PHY suspend/resume
automatically. Make use of this feature to make suspend to RAM work
with SATA drives on A3700.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A3700 comphy initialization is done in the firmware (TF-A). Looking at
the SATA PHY initialization routine, there is a comment about "vendor
specific" registers. Two registers are mentioned. They are not
initialized there in the firmware because they are AHCI related, while
the firmware at this location does only PHY configuration. The
solution to avoid doing such initialization is relying on U-Boot.
While this work at boot time, U-Boot is definitely not going to run
during a resume after suspending to RAM.
Two possible solutions were considered:
* Fixing the firmware.
* Fixing the kernel driver.
The first solution would take ages to propagate, while the second
solution is easy to implement as the driver as been a little bit
reworked to prepare for such platform configuration. Hence, this patch
adds an Armada 3700 configuration function to set these two registers
both at boot time (in the probe) and after a suspend (in the resume
path).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
At the beginning, only Armada 38x SoCs where supported by the
ahci_mvebu.c driver. Commit 15d3ce7b63bd ("ata: ahci_mvebu: add
support for Armada 3700 variant") introduced Armada 3700 support. As
opposed to Armada 38x SoCs, the 3700 variants do not have to configure
mbus and the regret option. This patch took care of avoiding such
configuration when not needed in the probe function, but failed to do
the same in the resume path. While doing so looks harmless by
experience, let's clean the driver logic and avoid doing this useless
configuration with Armada 3700 SoCs.
Because the logic is very similar between these two places, it has
been decided to factorize this code and put it in a "Armada 38x
configuration function". This function is part of a new
(per-compatible) platform data structure, so that the addition of such
configuration function for Armada 3700 will be eased.
Fixes: 15d3ce7b63bd ("ata: ahci_mvebu: add support for Armada 3700 variant")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
For Armada-38x (32-bit) SoCs, PM platform support has been added since:
commit 32f9494c9dfd ("ARM: mvebu: prepare pm-board.c for the
introduction of Armada 38x support")
commit 3cbd6a6ca81c ("ARM: mvebu: Add standby support")
For Armada 64-bit SoCs, like the A3700 also using this AHCI driver, PM
platform support has always existed.
There are even suspend/resume hooks in this driver since:
commit d6ecf15814888 ("ata: ahci_mvebu: add suspend/resume support")
Remove the stale comment at the end of this driver stating that all
the above does not exist yet.
Fixes: d6ecf15814888 ("ata: ahci_mvebu: add suspend/resume support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
|
|
Add an extra argument to ahci_platform_get_resources(), that is
for the bitmap representing the resource to get in this function.
Currently there is no resources to be defined, so all the callers set
'0' to the argument.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Fixes the following sparse warning:
drivers/ata/ahci_mvebu.c:85:5: warning:
symbol 'ahci_mvebu_stop_engine' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
There is an issue(Errata Ref#226) that the SATA can not be
detected via SATA Port-MultiPlayer(PMP) with following
error log:
ata1.15: PMP product ID mismatch
ata1.15: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata1.15: Port Multiplier vendor mismatch '0x1b4b'!='0x0'
ata1.15: PMP revalidation failed (errno=-19)
After debugging, the reason is found that the value Port-x
FIS-based Switching Control(PxFBS@0x40) become wrong.
According to design, the bits[11:8, 0] of register PxFBS
are cleared when Port Command and Status (0x18) bit[0]
changes its value from 1 to 0, i.e. falling edge of Port
Command and Status bit[0] sends PULSE that resets PxFBS
bits[11:8; 0].
So it needs a mvebu SATA WA to save the port PxFBS register
before PxCMD ST write and restore it afterwards.
This patch implements the WA in a separate function of
ahci_mvebu_stop_engine to override ahci_stop_gngine.
Signed-off-by: Evan Wang <xswang@marvell.com>
Cc: Ofer Heifetz <oferh@marvell.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The main difference in the new Armada 3700 is that no address
decoding needs to take place in the driver probe.
[gregory.clement@free-electrons.com: reformulate the commit log]
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Tested-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The newly added suspend/resume implementation for ahci_mvebu causes
a link error when CONFIG_PM_SLEEP is disabled:
ERROR: "ahci_platform_suspend_host" [drivers/ata/ahci_mvebu.ko] undefined!
ERROR: "ahci_platform_resume_host" [drivers/ata/ahci_mvebu.ko] undefined!
This adds the same #ifdef here that exists in the ahci_platform driver
which defines the above functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d6ecf1581488 ("ata: ahci_mvebu: add suspend/resume support")
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
- a number of libata core changes to better support NCQ TRIM.
- ahci now supports MSI-X in single IRQ mode to support a new
controller which doesn't implement MSI or INTX.
- ahci now supports edge-triggered IRQ mode to support a new controller
which for some odd reason did edge-triggered IRQ.
- the usual controller support additions and changes.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
libata: Do not blacklist Micron M500DC
ata: ahci_mvebu: add suspend/resume support
ahci, msix: Fix build error for !PCI_MSI
ahci: Add support for Cavium's ThunderX host controller
ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
libata: finally use __initconst in ata_parse_force_one()
drivers: ata: add support for Ceva sata host controller
devicetree:bindings: add devicetree bindings for ceva ahci
ahci: added support for Freescale AHCI sata
ahci: Store irq number in struct ahci_host_priv
ahci: Move interrupt enablement code to a separate function
Doc: libata: Fix spelling typo found in libata.xml
ata:sata_nv - Change 1 to true for bool type variable.
ata: add Broadcom AHCI SATA3 driver for STB chips
Documentation: devicetree: add Broadcom SATA binding
libata: Fix regression when the NCQ Send and Receive log page is absent
ata: hpt366: fix constant cast warning
ata: ahci_xgene: potential NULL dereference in probe
ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
...
|
|
This commit adds suspend/resume support to the ahci_mvebu driver. The
suspend hook doesn't do anything special despite calling the generic
ahci_platform_suspend_host() function. However, the resume hook has to
restore the MBus windows configuration, as well as the regret option.
Tested on Marvell Armada 388 GP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
According to the Armada 38x datasheet, the window base address
registers value is set in bits [31:4] of the register and corresponds
to the transaction address bits [47:20].
Therefore, the 32bit base address value should be shifted right by
20bits and left by 4bits, resulting in 16 bit shift right.
The bug as not been noticed yet because if the memory available on
the platform is less than 2GB, then the base address is zero.
[gregory.clement@free-electrons.com: add extra-explanation]
Fixes: a3464ed2f14 (ata: ahci_mvebu: new driver for Marvell Armada 380
AHCI interfaces)
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The owner module reference of the ahci platform's scsi_host is
initialized to libahci_platform's one, because these drivers use a
scsi_host_template defined in libahci_platform. So these drivers can
be unloaded even if the scsi device is being accessed.
This fixes it by pushing the scsi_host_template from libahci_platform
to all leaf drivers. The scsi_host_template is passed through a new
argument of ahci_platform_init_host().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch moves force_port_map and mask_port_map into the
ahci_host_priv structure. This allows to modify them into the AHCI
framework. This is needed by the new dt bindings representing ports as
the port_map mask is computed automatically.
Parameters modifying force_port_map, mask_port_map and flags have been
removed from the ahci_platform_init_host() function, and inputs in the
ahci_host_priv structure are now directly filed.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add a dynamic host_flags argument to make ahci_platform_init_host more flexible,
then remove the AHCI_HFLAGS(...) argument from some driver's ata_port_info,
and pass that in as the new argument.
Cc: Hans de Geode <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The Marvell Armada 380 SoC includes two AHCI compatible
interfaces. However, like all DMA-capable Marvell interface, they
require special handling to configure MBus windows. Therefore, this
commit adds a new ahci_mvebu driver, which relies on the
libahci_platform.c code recently introduced.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
