| Age | Commit message (Collapse) | Author |
|---|
|
Until we tell ACPI that we support generic initiators, it will have
to operate in fall back domain mode and all _PXM entries should
be on existing non GI domains.
This patch sets the relevant OSC bit to make that happen.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Generic Initiators are a new ACPI concept that allows for the
description of proximity domains that contain a device which
performs memory access (such as a network card) but neither
host CPU nor Memory.
This patch has the parsing code and provides the infrastructure
for an architecture to associate these new domains with their
nearest memory processing node.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.10 merge window
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (37 commits)
thunderbolt: Capitalize comment on top of QUIRK_FORCE_POWER_LINK_CONTROLLER
thunderbolt: Correct tb_check_quirks() kernel-doc
thunderbolt: Log correct zeroX entries in decode_error()
thunderbolt: Handle ERR_LOCK notification
thunderbolt: Use "if USB4" instead of "depends on" in Kconfig
thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m
thunderbolt: Only stop control channel when entering freeze
thunderbolt: debugfs: Fix uninitialized return in counters_write()
thunderbolt: Add debugfs interface
thunderbolt: No need to warn in TB_CFG_ERROR_INVALID_CONFIG_SPACE
thunderbolt: Introduce tb_switch_is_tiger_lake()
thunderbolt: Introduce tb_switch_is_ice_lake()
thunderbolt: Check for Intel vendor ID when identifying controller
thunderbolt: Introduce tb_port_is_nhi()
thunderbolt: Introduce tb_switch_next_cap()
thunderbolt: Introduce tb_port_next_cap()
thunderbolt: Move struct tb_cap_any to tb_regs.h
thunderbolt: Add runtime PM for Software CM
thunderbolt: Create device links from ACPI description
ACPI: Export acpi_get_first_physical_node() to modules
...
|
|
|
|
The ACPICA debug code of ACPI_SYSTEM_COMPONENT and ACPI_MODULE_NAME()
is not used in wakeup.c, remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit (87521e16a7ab "acpi-video-detect: Rewrite backlight interface
selection logic"), ACPI_DEBUG_PRINT() was remove, so ACPI_MODULE_NAME()
and _COMPONENT are not used anymore, remove them.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ACPICA debug code is not used, can be removed.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ACPICA debug code is not used anywhere in processor_core.c
and processor_thermal.c, remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove the not used ACPICA debug code _COMPONENT and ACPI_MODULE_NAME()
which were not used even when proc.c was introduced.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ACPICA debug code _COMPONENT and ACPI_MODULE_NAME() are
not used, so can be removed.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit (ff491a7334ac "netlink: change return-value logic of
netlink_broadcast()"), ACPI_DEBUG_PRINT() was removed from event.c,
so the ACPICA debug code is not used, remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ACPICA debug ACPI_MODULE_NAME() definition is not used, remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The _COMPONENT and ACPI_MODULE_NAME() were not used even when
the debugfs.c was introduced, remove them.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA debug code _COMPONENT and ACPI_MODULE_NAME() is not
used in custom_method.c, remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit 737f1a9f8082 ("ACPI / scan: Make container driver use
struct acpi_scan_handler"), ACPICA debug print function calls were
removed, so the leftover ACPICA debug functionality is useless,
remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI_MODULE_NAME() is not used in the acpi_platform.c, remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit 0a34764411aa ("ACPI / scan: Make memory hotplug drive
use struct acpi_scan_handler"), all the ACPICA debug functionality
was removed, remove the leftover ACPICA debug code.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI_MODULE_NAME() is only needed for ACPICA debug functionality
such as ACPI_DEBUG_PRINT() which is not used in acpi_lpss.c,
remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI_MODULE_NAME() is only needed for ACPICA debug functionality
such as ACPI_DEBUG_PRINT() which is not used in acpi_cmos_rtc.c,
remove it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Update kernel-doc line comments to fix warnings reported by make W=1:
drivers/acpi/pci_root.c:71: warning: Function parameter or
member 'handle' not described in 'acpi_is_root_bridge'
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix the following warnings.
drivers/acpi/acpi_pnp.c:382:13: warning: no previous prototype
for ‘acpi_pnp_init’ [-Wmissing-prototypes].
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
config_item_put() should be called in the drop_item callback, to
decrement refcount for the config item.
Fixes: 772bf1e2878ec ("ACPI: configfs: Unload SSDT on configfs entry removal")
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject edit ]
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The default backlight interface is AMD's radeon_bl0 which does not
work on this system, so use the ACPI backlight interface on it
instead.
BugLink: https://bugs.launchpad.net/bugs/1894667
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make the included header files appear in the alphabetical order and
remove the unnecessary header file inclusions.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since APD_ADDR(desc) is only used when CONFIG_X86_AMD_PLATFORM_DEVICE
or CONFIG_ARM64 is set, no need for the stub APD_ADDR(desc) definition
covering the other cases, so remove it.
Also update the comments for #endif.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI_MODULE_NAME() is used for ACPI debug output when using
ACPI debug print functions, but ACPI debug print functions are
not used in acpi_apd.c, so remove the ACPI_MODULE_NAME() from it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The flags field is not used in anywhere, so remove it along with two
symbols related to it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
commit 7ff55d174cbf ("ACPI / APD: Provide build-in properties of the
UART") added the struct property_entry *properties field to struct
apd_device_desc, but didn't add the kernel doc for it, so add it now.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into dma-mapping-for-next
Pull in the latest 5.9 tree for the commit to revert the
V4L2_FLAG_MEMORY_NON_CONSISTENT uapi addition.
|
|
acpi_get_node() calls acpi_get_pxm() to evaluate the _PXM AML method
for entries found in DSDT/SSDT. ACPI 6.3 sec 6.2.14 states
"_PXM evaluates to an integer that identifies a device as belonging to
a Proximity Domain defined in the System Resource Affinity Table (SRAT)."
Hence a _PXM method should not result in creation of a new NUMA node.
Before this patch, _PXM could result in partial instantiation of
NUMA node, missing elements such as zone lists. A call to
devm_kzalloc(), for example, results in a NULL pointer dereference.
This patch therefore replaces the acpi_map_pxm_to_node() with a call
to pxm_to_node().
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As this function is no longer allowed to create new mappings
let us rename it to reflect this.
Note all nodes should already exist before any of the users
of this function are called.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Several ACPI static tables contain references to proximity domains.
ACPI 6.3 has clarified that only entries in SRAT may define a new
domain (sec 5.2.16).
Those tables described in the ACPI spec have additional clarifying text.
NFIT: Table 5-132,
"Integer that represents the proximity domain to which the memory
belongs. This number must match with corresponding entry in the
SRAT table."
HMAT: Table 5-145,
"... This number must match with the corresponding entry in the SRAT
table's processor affinity structure ... if the initiator is a processor,
or the Generic Initiator Affinity Structure if the initiator is a generic
initiator".
IORT and DMAR are defined by external specifications.
Intel Virtualization Technology for Directed I/O Rev 3.1 does not make any
explicit statements, but the general SRAT statement above will still apply.
https://software.intel.com/sites/default/files/managed/c5/15/vt-directed-io-spec.pdf
IO Remapping Table, Platform Design Document rev D, also makes not explicit
statement, but refers to ACPI SRAT table for more information and again the
generic SRAT statement above applies.
https://developer.arm.com/documentation/den0049/d/
In conclusion, any proximity domain specified in these tables, should be a
reference to a proximity domain also found in SRAT, and they should not be
able to instantiate a new domain. Hence we switch to pxm_to_node() which
will only return existing nodes.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function should check the validity of the pxm value before using
it to index the pxm_to_node_map[] array.
Whilst hardening this code may be good in general, the main intent
here is to enable following patches that use this function to replace
acpi_map_pxm_to_node() for non SRAT usecases which should return
NO_NUMA_NODE for PXM entries not matching with those in SRAT.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix the lapic_timer_needs_broadcast() stub for
ARCH_APICTIMER_STOPS_ON_C3 unset to actually return
a value.
Fixes: aa6b43d57f99 ("ACPI: processor: Use CPUIDLE_FLAG_TIMER_STOP")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some platforms have bogus _CST which might cause unexpectd behavior
in the CPU idle driver. Some bogus _CST might be unable to be
disassembled by acpica-tools due to broken format.
Print extra log if the _CST extraction/verification failes.
This can be used to help narrow down why the CPU idle driver fails
to behave as expected.
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver adds support for Dynamic Platform and Thermal Framework
(DPTF) PCH (Platform Controller Hub) FIVR (Fully Integrated Voltage
Regulator) participant support.
This participant is responsible for exposing platform telemetry and
control for:
freq_mhz_high_clock
freq_mhz_low_clock
These attributes are used to get and set PCH FIVR switching frequency
for thermal and radio frequency interference mitigation.
Refer to Documentation/ABI/testing/sysfs-platform-dptf for ABI details.
ACPI methods description used in this driver:
RFC0: This ACPI method to set PCH FIVR switching frequency when FIVR
clock is 19.2MHz or 24MHz. The ACPI method takes a DWORD value.
GFC0: This ACPI method to get PCH FIVR switching frequency when FIVR
clock is 19.2MHz or 24MHz.
RFC1: This ACPI method to set PCH FIVR switching frequency when FIVR
clock is 38.4MHz. The ACPI method takes a DWORD value.
GFC1: This ACPI method to get PCH FIVR switching frequency when FIVR
clock is 38.4MHz.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Ampere Altra SOC supports only 32-bit ECAM reads. Add an MCFG quirk for
the platform.
Link: https://lore.kernel.org/r/1596751055-12316-1-git-send-email-tuanphan@os.amperecomputing.com
Signed-off-by: Tuan Phan <tuanphan@os.amperecomputing.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
|
|
The C3 BusMaster idle code takes lock in a number of places, some deep
inside the ACPI code. Instead of wrapping it all in RCU_NONIDLE, have
the driver take over RCU-idle duty and avoid flipping RCU state back
and forth a lot.
( by marking 'C3 && bm_check' as RCU_IDLE, we _must_ call enter_bm() for
that combination, otherwise we'll loose RCU-idle, this requires
shuffling some code around )
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make acpi_processor_idle() use the generic TLB flushing code.
This again removes RCU usage after rcu_idle_enter().
(XXX make every C3 invalidate TLBs, not just C3-BM)
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make acpi_processor_idle use the common broadcast code, there's no
reason not to. This also removes some RCU usage after
rcu_idle_enter().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
CPER records describing a firmware-first error are identified by GUID.
The ghes driver currently logs, but ignores any unknown CPER records.
This prevents describing errors that can't be represented by a standard
entry, that would otherwise allow a driver to recover from an error.
The UEFI spec calls these 'Non-standard Section Body' (N.2.3 of
version 2.8).
Add a notifier chain for these non-standard/vendor-records. Callers
must identify their type of records by GUID.
Record data is copied to memory from the ghes_estatus_pool to allow
us to keep it until after the notifier has run.
Co-developed-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20200903123456.1823-2-shiju.jose@huawei.com
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
|
|
It is revealed now that TPS68470 OpRegion driver has been added
in slightly different scope. Let's move it to the drivers/acpi/pmic/
folder for sake of the unification.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It's a bit better to maintain and allows to avoid mistakes in the future
with PMIC OpRegion drivers, if we split out Kconfig and Makefile
for ACPI PMIC to its own folder.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use kobj_to_dev() instead of container_of()
Signed-off-by: Wang Qing <wangqing@vivo.com>
Acked-by: Vishal Verma <vishal.l.verma@intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
MCFG is an optional ACPI table. Given there are machines without PCI (or
it is hidden) we have been receiving queries/complaints about what this
message means given it's being presented as an error.
Reduce the message severity. The ACPI table list printed at boot will
continue to provide another way to detect when the table is missing.
Link: https://lore.kernel.org/r/20200908210359.569294-1-jeremy.linton@arm.com
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
|
|
Sync drm-intel-gt-next here so we can have an unified fixes flow.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Define ACPI_GPE_USE_LOGICAL_ADDRESSES in aclinux.h and modify
acpi_os_initialize() to store the logical addresses of the FADT GPE
blocks 0 and 1 in acpi_gbl_xgpe0_block_logical_address and
acpi_gbl_xgpe1_block_logical_address, respectively, so as to allow
ACPICA to use them for accessing GPE registers in system memory,
instead of using their physical addresses and looking up the
corresponding logical addresses on every access attempt, which is
inefficient.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Modify acpi_os_map_generic_address() to return the pointer returned
by acpi_os_map_iomem() which represents the logical address
corresponding to the struct acpi_generic_address argument passed to
it or NULL if that address cannot be obtained (for example, the
argument does not represent an address in system memory or it could
not be mapped by the OS).
Among other things, that will allow the ACPI OS layer to pass the
logical addresses of the FADT GPE blocks 0 and 1 to ACPICA going
forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The logical address of every GPE block in system memory must be
known before passing it to acpi_ev_initialize_gpe_block(), because
memory cannot be mapped on the fly from an interrupt handler.
Accordingly, the host OS must map every GPE block in system
memory upfront and it can store the logical addresses of GPE
blocks for future use.
If these logical addresses were known to ACPICA, it could use them
instead of the corresponding physical addresses of GPE block for
GPE register accesses and the memory mapping lookups carried out
by acpi_os_read_memory() and acpi_os_write_memory() on every
attempt to access a GPE register would not be necessary any more.
To allow that to happen, introduce the ACPI_GPE_USE_LOGICAL_ADDRESSES
symbol to indicate whether or not the host OS wants ACPICA to use the
logical addresses of GPE registers in system memory directly (which
is the case if this symbol is defined). Moreover, conditional on
whether ACPI_GPE_USE_LOGICAL_ADDRESSES is defined, introduce two new
global variables for storing the logical addresses of the FADT GPE
blocks 0 and 1, respectively, acpi_gbl_xgpe0_block_logical_address and
acpi_gbl_xgpe1_block_logical_address, make acpi_ev_gpe_initialize()
pass their values instead of the physical addresses of the GPE blocks
in question to acpi_ev_create_gpe_block() and modify
acpi_hw_gpe_read() and acpi_hw_gpe_write() to access memory directly
via the addresses stored in the struct acpi_gpe_address objects,
which are expected to be the logical addresses of GPE registers if
ACPI_GPE_USE_LOGICAL_ADDRESSES is defined.
With the above changes in place, a host OS wanting ACPICA to
access GPE registers directly through their logical addresses
needs to define the ACPI_GPE_USE_LOGICAL_ADDRESSES symbol and
make sure that the logical addresses of the FADT GPE blocks 0
and 1 are stored in acpi_gbl_xgpe0_block_logical_address and
acpi_gbl_xgpe1_block_logical_address, respectively, prior to
calling acpi_ev_gpe_initialize().
[If such a host OS also uses acpi_install_gpe_block() to add
non-FADT GPE register blocks located in system memory, it must
pass their logical addresses instead of their physical addresses
to this function.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
