| Age | Commit message (Collapse) | Author |
|---|
|
This patch improves discard bio split for address and size alignment in
__blkdev_issue_discard(). The aligned discard bio may help underlying
device controller to perform better discard and internal garbage
collection, and avoid unnecessary internal fragment.
Current discard bio split algorithm in __blkdev_issue_discard() may have
non-discarded fregment on device even the discard bio LBA and size are
both aligned to device's discard granularity size.
Here is the example steps on how to reproduce the above problem.
- On a VMWare ESXi 6.5 update3 installation, create a 51GB virtual disk
with thin mode and give it to a Linux virtual machine.
- Inside the Linux virtual machine, if the 50GB virtual disk shows up as
/dev/sdb, fill data into the first 50GB by,
# dd if=/dev/zero of=/dev/sdb bs=4096 count=13107200
- Discard the 50GB range from offset 0 on /dev/sdb,
# blkdiscard /dev/sdb -o 0 -l 53687091200
- Observe the underlying mapping status of the device
# sg_get_lba_status /dev/sdb -m 1048 --lba=0
descriptor LBA: 0x0000000000000000 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000000000800 blocks: 16773120 deallocated
descriptor LBA: 0x0000000000fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000001000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000017ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000001800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000001fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000002000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000027ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000002800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000002fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000003000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000037ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000003800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000003fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000004000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000047ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000004800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000004fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000005000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000057ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000005800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000005fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000006000000 blocks: 6291456 deallocated
descriptor LBA: 0x0000000006600000 blocks: 0 deallocated
Although the discard bio starts at LBA 0 and has 50<<30 bytes size which
are perfect aligned to the discard granularity, from the above list
these are many 1MB (2048 sectors) internal fragments exist unexpectedly.
The problem is in __blkdev_issue_discard(), an improper algorithm causes
an improper bio size which is not aligned.
25 int __blkdev_issue_discard(struct block_device *bdev, sector_t sector,
26 sector_t nr_sects, gfp_t gfp_mask, int flags,
27 struct bio **biop)
28 {
29 struct request_queue *q = bdev_get_queue(bdev);
[snipped]
56
57 while (nr_sects) {
58 sector_t req_sects = min_t(sector_t, nr_sects,
59 bio_allowed_max_sectors(q));
60
61 WARN_ON_ONCE((req_sects << 9) > UINT_MAX);
62
63 bio = blk_next_bio(bio, 0, gfp_mask);
64 bio->bi_iter.bi_sector = sector;
65 bio_set_dev(bio, bdev);
66 bio_set_op_attrs(bio, op, 0);
67
68 bio->bi_iter.bi_size = req_sects << 9;
69 sector += req_sects;
70 nr_sects -= req_sects;
[snipped]
79 }
80
81 *biop = bio;
82 return 0;
83 }
84 EXPORT_SYMBOL(__blkdev_issue_discard);
At line 58-59, to discard a 50GB range, req_sects is set as return value
of bio_allowed_max_sectors(q), which is 8388607 sectors. In the above
case, the discard granularity is 2048 sectors, although the start LBA
and discard length are aligned to discard granularity, req_sects never
has chance to be aligned to discard granularity. This is why there are
some still-mapped 2048 sectors fragment in every 4 or 8 GB range.
If req_sects at line 58 is set to a value aligned to discard_granularity
and close to UNIT_MAX, then all consequent split bios inside device
driver are (almostly) aligned to discard_granularity of the device
queue. The 2048 sectors still-mapped fragment will disappear.
This patch introduces bio_aligned_discard_max_sectors() to return the
the value which is aligned to q->limits.discard_granularity and closest
to UINT_MAX. Then this patch replaces bio_allowed_max_sectors() with
this new routine to decide a more proper split bio length.
But we still need to handle the situation when discard start LBA is not
aligned to q->limits.discard_granularity, otherwise even the length is
aligned, current code may still leave 2048 fragment around every 4GB
range. Therefore, to calculate req_sects, firstly the start LBA of
discard range is checked (including partition offset), if it is not
aligned to discard granularity, the first split location should make
sure following bio has bi_sector aligned to discard granularity. Then
there won't be still-mapped fragment in the middle of the discard range.
The above is how this patch improves discard bio alignment in
__blkdev_issue_discard(). Now with this patch, after discard with same
command line mentiond previously, sg_get_lba_status returns,
descriptor LBA: 0x0000000000000000 blocks: 106954752 deallocated
descriptor LBA: 0x0000000006600000 blocks: 0 deallocated
We an see there is no 2048 sectors segment anymore, everything is clean.
Reported-and-tested-by: Acshai Manoj <acshai.manoj@microfocus.com>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Enzo Matsumiya <ematsumiya@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 7520872c0cf4 ("block: don't defer flushes on blk-mq + scheduling")
tried to fix deadlock for cycled wait between flush requests and data
request into flush_data_in_flight. The former holded all driver tags
and wait for data request completion, but the latter can not complete
for waiting free driver tags.
After commit 923218f6166a ("blk-mq: don't allocate driver tag upfront
for flush rq"), flush requests will not get driver tag before queuing
into flush queue.
* With elevator, flush request just get sched_tags before inserting
flush queue. It will not get driver tag until issue them to driver.
data request on list fq->flush_data_in_flight will complete in
the end.
* Without elevator, each flush request will get a driver tag when
allocate request. Then data request on fq->flush_data_in_flight
don't worry about lacking driver tag.
In both of these cases, cycled wait cannot be true. So we may allow
to defer flush request.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The sparse tool complains as follows:
block/blk-timeout.c:93:12: warning:
symbol 'blk_timeout_init' was not declared. Should it be static?
Function blk_timeout_init() is not used outside of blk-timeout.c, so
mark it static.
Fixes: 9054650fac24 ("block: relax jiffies rounding for timeouts")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The reverse-order double lock dance in ioc_release_fn() is using a
retry loop. This is a problem on PREEMPT_RT because it could preempt
the task that would release q->queue_lock and thus live lock in the
retry loop.
RCU is already managing the freeing of the request queue and icq. If
the trylock fails, use RCU to guarantee that the request queue and
icq are not freed and re-acquire the locks in the correct order,
allowing forward progress.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The legacy CFQ IO scheduler could call put_io_context() in its exit_icq()
elevator callback. This led to a lockdep warning, which was fixed in
commit d8c66c5d5924 ("block: fix lockdep warning on io_context release
put_io_context()") by using a nested subclass for the ioc spinlock.
However, with commit f382fb0bcef4 ("block: remove legacy IO schedulers")
the CFQ IO scheduler no longer exists.
The BFQ IO scheduler also implements the exit_icq() elevator callback but
does not call put_io_context().
The nested subclass for the ioc spinlock is no longer needed. Since it
existed as an exception and no longer applies, remove the nested subclass
usage.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a new max_active zones definition in the sysfs documentation.
This definition will be common for all devices utilizing the zoned block
device support in the kernel.
Export max_active_zones according to this new definition for NVMe Zoned
Namespace devices, ZAC ATA devices (which are treated as SCSI devices by
the kernel), and ZBC SCSI devices.
Add the new max_active_zones member to struct request_queue, rather
than as a queue limit, since this property cannot be split across stacking
drivers.
For SCSI devices, even though max active zones is not part of the ZBC/ZAC
spec, export max_active_zones as 0, signifying "no limit".
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a new max_open_zones definition in the sysfs documentation.
This definition will be common for all devices utilizing the zoned block
device support in the kernel.
Export max open zones according to this new definition for NVMe Zoned
Namespace devices, ZAC ATA devices (which are treated as SCSI devices by
the kernel), and ZBC SCSI devices.
Add the new max_open_zones member to struct request_queue, rather
than as a queue limit, since this property cannot be split across stacking
drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 826f2f48da8c331ac51e1381998d318012d66550.
Qian Cai reports that this commit causes stalls with swap. Revert until
the reason can be figured out.
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In theory, when GENHD_FL_NO_PART_SCAN is set, no partitions can be created
on one disk. However, ioctl(BLKPG, BLKPG_ADD_PARTITION) doesn't check
GENHD_FL_NO_PART_SCAN, so partitions still can be added even though
GENHD_FL_NO_PART_SCAN is set.
So far blk_drop_partitions() only removes partitions when disk_part_scan_enabled()
return true. This way can make ghost partition on loop device after changing/clearing
FD in case that PARTSCAN is disabled, such as partitions can be added
via 'parted' on loop disk even though GENHD_FL_NO_PART_SCAN is set.
Fix this issue by always removing partitions in blk_drop_partitions(), and
this way is correct because the current code supposes that no partitions
can be added in case of GENHD_FL_NO_PART_SCAN.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In doing high IOPS testing, blk-mq is generally pretty well optimized.
There are a few things that stuck out as using more CPU than what is
really warranted, and one thing is the round_jiffies_up() that we do
twice for each request. That accounts for about 0.8% of the CPU in
my testing.
We can make this cheaper by avoiding an integer division, by just adding
a rough HZ mask that we can AND with instead. The timeouts are only on a
second granularity already, we don't have to be that accurate here and
this patch barely changes that. All we care about is nice grouping.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block fixes from Jens Axboe:
- Fix for inflight accounting, which affects only dm (Ming)
- Fix documentation error for bfq (Yufen)
- Fix memory leak for nbd (Zheng)
* tag 'block-5.8-2020-07-10' of git://git.kernel.dk/linux-block:
nbd: Fix memory leak in nbd_add_socket
blk-mq: consider non-idle request as "inflight" in blk_mq_rq_inflight()
docs: block: update and fix tiny error for bfq
|
|
We've already validated the 'q->elevator' before calling
->ops.completed_request() in blk_mq_sched_completed_request(), thus no
need to validate rq->internal_tag again. Rmove it.
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove unnecessary local variable 'ret' in blk_mq_dispatch_hctx_list().
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We never set any congested bits in the group writeback instances of it.
And for the simpler bdi-wide case a simple scalar field is all that
that is needed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
md is the last driver using the legacy media_changed method. Switch
it over to (not so) new ->clear_events approach, which also removes the
need for the ->revalidate_disk method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[axboe: remove unused 'bdops' variable in disk_clear_events()]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move .nr_active update and request assignment into blk_mq_get_driver_tag(),
all are good to do during getting driver tag.
Meantime blk-flush related code is simplified and flush request needn't
to update the request table manually any more.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Current handling of q->mq_ops->queue_rq result is a bit ugly:
- two branches which needs to 'continue' have to check if the
dispatch local list is empty, otherwise one bad request may
be retrieved via 'rq = list_first_entry(list, struct request, queuelist);'
- the branch of 'if (unlikely(ret != BLK_STS_OK))' isn't easy
to follow, since it is actually one error branch.
Streamline this handling, so the code becomes more readable, meantime
potential kernel oops can be avoided in case that the last request in
local dispatch list is failed.
Fixes: fc17b6534eb8 ("blk-mq: switch ->queue_rq return value to blk_status_t")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add support for NVM Express Zoned Namespaces (ZNS) Command Set defined
in NVM Express TP4053. Zoned namespaces are discovered based on their
Command Set Identifier reported in the namespaces Namespace
Identification Descriptor list. A successfully discovered Zoned
Namespace will be registered with the block layer as a host managed
zoned block device with Zone Append command support. A namespace that
does not support append is not supported by the driver.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <keith.busch@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In the zoned storage model, the sectors within a zone are typically all
writeable. With the introduction of the Zoned Namespace (ZNS) Command
Set in the NVM Express organization, the model was extended to have a
specific writeable capacity.
Extend the zone descriptor data structure with a zone capacity field to
indicate to the user how many sectors in a zone are writeable.
Introduce backward compatibility in the zone report ioctl by extending
the zone report header data structure with a flags field to indicate if
the capacity field is available.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Merge in 5.8-rc4 for-5.9/block to setup for-5.9/drivers, to provide
a clean base and making the life for the NVMe changes easier.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v5.8-rc4': (732 commits)
Linux 5.8-rc4
x86/ldt: use "pr_info_once()" instead of open-coding it badly
MIPS: Do not use smp_processor_id() in preemptible code
MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen
.gitignore: Do not track `defconfig` from `make savedefconfig`
io_uring: fix regression with always ignoring signals in io_cqring_wait()
x86/ldt: Disable 16-bit segments on Xen PV
x86/entry/32: Fix #MC and #DB wiring on x86_32
x86/entry/xen: Route #DB correctly on Xen PV
x86/entry, selftests: Further improve user entry sanity checks
x86/entry/compat: Clear RAX high bits on Xen PV SYSENTER
i2c: mlxcpld: check correct size of maximum RECV_LEN packet
i2c: add Kconfig help text for slave mode
i2c: slave-eeprom: update documentation
i2c: eg20t: Load module automatically if ID matches
i2c: designware: platdrv: Set class based on DMI
i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665
mm/page_alloc: fix documentation error
vmalloc: fix the owner argument for the new __vmalloc_node_range callers
mm/cma.c: use exact_nid true to fix possible per-numa cma leak
...
|
|
If blk_mq_submit_bio flushes the plug list, bios for other disks can
show up on current->bio_list. As that doesn't involve any stacking of
block device it is entirely harmless and we should not warn about
this case.
Fixes: ff93ea0ce763 ("block: shortcut __submit_bio_noacct for blk-mq drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
dm-multipath is the only user of blk_mq_queue_inflight(). When
dm-multipath calls blk_mq_queue_inflight() to check if it has
outstanding IO it can get a false negative. The reason for this is
blk_mq_rq_inflight() doesn't consider requests that are no longer
MQ_RQ_IN_FLIGHT but that are now MQ_RQ_COMPLETE (->complete isn't
called or finished yet) as "inflight".
This causes request-based dm-multipath's dm_wait_for_completion() to
return before all outstanding dm-multipath requests have actually
completed. This breaks DM multipath's suspend functionality because
blk-mq requests complete after DM's suspend has finished -- which
shouldn't happen.
Fix this by considering any request not in the MQ_RQ_IDLE state
(so either MQ_RQ_COMPLETE or MQ_RQ_IN_FLIGHT) as "inflight" in
blk_mq_rq_inflight().
Fixes: 3c94d83cb3526 ("blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block fixes from Jens Axboe:
- NVMe fixes from Christoph:
- Fix crash in multi-path disk add (Christoph)
- Fix ignore of identify error (Sagi)
- Fix a compiler complaint that a function should be static (Wei)
* tag 'block-5.8-2020-07-05' of git://git.kernel.dk/linux-block:
block: make function __bio_integrity_free() static
nvme: fix a crash in nvme_mpath_add_disk
nvme: fix identify error status silent ignore
|
|
Pull block fixes from Jens Axboe:
- Use kvfree_sensitive() for the block keyslot free (Eric)
- Sync blk-mq debugfs flags (Hou)
- Memory leak fix in virtio-blk error path (Hou)
* tag 'block-5.8-2020-07-01' of git://git.kernel.dk/linux-block:
virtio-blk: free vblk-vqs in error path of virtblk_probe()
block/keyslot-manager: use kvfree_sensitive()
blk-mq-debugfs: update blk_queue_flag_name[] accordingly for new flags
|
|
bio_alloc_bioset references current->bio_list[1], so we need to
initialize it for the blk-mq submission path as well.
Fixes: ff93ea0ce763 ("block: shortcut __submit_bio_noacct for blk-mq drivers")
Reported-by: Qian Cai <cai@lca.pw>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix sparse build warning:
block/bio-integrity.c:27:6: warning:
symbol '__bio_integrity_free' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commits the following commits:
37f4a24c2469a10a4c16c641671bd766e276cf9f
723bf178f158abd1ce6069cb049581b3cb003aab
36a3df5a4574d5ddf59804fcd0c4e9654c514d9a
The last one is the culprit, but we have to go a bit deeper to get this
to revert cleanly. There's been a report that this breaks some MMC
setups [1], and also causes an issue with swap [2]. Until this can be
figured out, revert the offending commits.
[1] https://lore.kernel.org/linux-block/57fb09b1-54ba-f3aa-f82c-d709b0e6b281@samsung.com/
[2] https://lore.kernel.org/linux-block/20200702043721.GA1087@lca.pw/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
ktime_to_ns(ktime_get()), which is expensive, does not need to be called
if blk_iolatency_enabled() return false in blkcg_iolatency_done_bio().
Postponing ktime_to_ns(ktime_get()) execution reduces the CPU usage when
blk_iolatency is disabled.
Signed-off-by: Hongnan Li <hongnan.li@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now that submit_bio_noacct has a decent blk-mq fast path there is no
more need for this bypass.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
For blk-mq drivers bios can only be inserted for the same queue. So
bypass the complicated sorting logic in __submit_bio_noacct with
a blk-mq simpler submission helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Split out a __submit_bio_noacct helper for the actual de-recursion
algorithm, and simplify the loop by using a continue when we can't
enter the queue for a bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
generic_make_request has always been very confusingly misnamed, so rename
it to submit_bio_noacct to make it clear that it is submit_bio minus
accounting and a few checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The make_request_fn is a little weird in that it sits directly in
struct request_queue instead of an operation vector. Replace it with
a block_device_operations method called submit_bio (which describes much
better what it does). Also remove the request_queue argument to it, as
the queue can be derived pretty trivially from the bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The variable is only used once, so just open code the bio_sector()
there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
All registers disks must have a valid queue pointer, so don't bother to
log a warning for that case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The "generic_make_request: " prefix has no value, and will soon become
stale.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The queue can be trivially derived from the bio, so pass one less
argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Just use rq directly, the usage of list_entry_rq() doesn't make any
sense.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is a statement that is indented one level too deeply, fix it
by removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move .nr_active update and request assignment into blk_mq_get_driver_tag(),
all are good to do during getting driver tag.
Meantime blk-flush related code is simplified and flush request needn't
to update the request table manually any more.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It is used by blk-mq.c only, so move it to the source file.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
blk_mq_get_driver_tag() is only used by blk-mq.c and is supposed to
stay in blk-mq.c, so move it and preparing for cleanup code of
get/put driver tag.
Meantime hctx_may_queue() is moved to header file and it is fine
since it is defined as inline always.
No functional change.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
More and more drivers want to get batching requests queued from
block layer, such as mmc, and tcp based storage drivers. Also
current in-tree users have virtio-scsi, virtio-blk and nvme.
For none, we already support batching dispatch.
But for io scheduler, every time we just take one request from scheduler
and pass the single request to blk_mq_dispatch_rq_list(). This way makes
batching dispatch not possible when io scheduler is applied. One reason
is that we don't want to hurt sequential IO performance, becasue IO
merge chance is reduced if more requests are dequeued from scheduler
queue.
Try to support batching dispatch for io scheduler by starting with the
following simple approach:
1) still make sure we can get budget before dequeueing request
2) use hctx->dispatch_busy to evaluate if queue is busy, if it is busy
we fackback to non-batching dispatch, otherwise dequeue as many as
possible requests from scheduler, and pass them to blk_mq_dispatch_rq_list().
Wrt. 2), we use similar policy for none, and turns out that SCSI SSD
performance got improved much.
In future, maybe we can develop more intelligent algorithem for batching
dispatch.
Baolin has tested this patch and found that MMC performance is improved[3].
[1] https://lore.kernel.org/linux-block/20200512075501.GF1531898@T590/#r
[2] https://lore.kernel.org/linux-block/fe6bd8b9-6ed9-b225-f80c-314746133722@grimberg.me/
[3] https://lore.kernel.org/linux-block/CADBw62o9eTQDJ9RvNgEqSpXmg6Xcq=2TxH0Hfxhp29uF2W=TXA@mail.gmail.com/
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pass obtained budget count to blk_mq_dispatch_rq_list(), and prepare
for supporting fully batching submission.
With the obtained budget count, it is easier to put extra budgets
in case of .queue_rq failure.
Meantime remove the old 'got_budget' parameter.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE is returned from
.queue_rq, the 'list' variable always holds this rq which isn't
queued to LLD successfully.
So blk_mq_dispatch_rq_list() always returns false from the branch
of '!list_empty(list)'.
No functional change.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move code for getting driver tag and budget into one helper, so
blk_mq_dispatch_rq_list gets a bit simplified, and easier to read.
Meantime move updating of 'no_tag' and 'no_budget_available' into
the branch for handling partial dispatch because that is exactly
consumer of the two local variables.
Also rename the parameter of 'got_budget' as 'ask_budget'.
No functional change.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
All requests in the 'list' of blk_mq_dispatch_rq_list belong to same
hctx, so it is better to pass hctx instead of request queue, because
blk-mq's dispatch target is hctx instead of request queue.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
blk-mq budget is abstract from scsi's device queue depth, and it is
always per-request-queue instead of hctx.
It can be quite absurd to get a budget from one hctx, then dequeue a
request from scheduler queue, and this request may not belong to this
hctx, at least for bfq and deadline.
So fix the mess and always pass request queue to get/put budget
callback.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Make blk_ksm_destroy() use the kvfree_sensitive() function (which was
introduced in v5.8-rc1) instead of open-coding it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
