| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86, nmi: Move LVT un-masking into irq handlers
perf events, x86: Work around the Nehalem AAJ80 erratum
perf, x86: Fix BTS condition
ftrace: Build without frame pointers on Microblaze
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Configure IOAPIC pins for USB and SATA to level type
x86: devicetree: Configure IOAPIC pin only once
x86, setup: When probing memory with e801, use ax/bx as a pair
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3+: voltage: remove initial voltage
OMAP4: Intialize IVA Device in addition to DSP device.
omap: rx51: mark reserved memory earlier
OMAP3: l3: fix for "irq 10: nobody cared" message
arm: omap2: enable smc instruction for sleep34xx
OMAP2/3: hwmod: fix gpio-reset timeouts seen during bootup.
OMAP3: PM: Do not rely on ROM code to restore CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL
OMAP2+: PM: Fix the saving of CM_AUTOIDLE_PLL register on scratchpad area
OMAP4: clock data: Change DSS clock aliases
OMAP2+: hwmod data: Fix wrong dma_system end address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/mm: Set all online nodes in N_NORMAL_MEMORY
|
|
In some cases gcc >= 4.5.2 will optimize away current_thread_info(). To
prevent gcc from doing so the stack address has to be obtained via inline
asm.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make HoneyPot ProcFS depend on CONFIG_PROC_FS so that it will build.
Recommended by Christoph Hellwig.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=33692
Reported-by: Simon Danner <danner.simon@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds support for 64 bit atomic operations on 32 bit UML systems. XFS
needs them since 2.6.38.
$ make ARCH=um SUBARCH=i386
...
LD .tmp_vmlinux1
fs/built-in.o: In function `xlog_regrant_reserve_log_space':
xfs_log.c:(.text+0xd8584): undefined reference to `atomic64_read_386'
xfs_log.c:(.text+0xd85ac): undefined reference to `cmpxchg8b_emu'
...
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=32812
Reported-by: Martin Walch <walch.martin@web.de>
Tested-by: Martin Walch <walch.martin@web.de>
Cc: Martin Walch <walch.martin@web.de>
Cc: <stable@kernel.org> [2.6.38.x 084189a: um: disable CONFIG_CMPXCHG_LOCAL]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We use io_apic_setup_irq_pin() in order to configure pin's interrupt
number polarity and type. This is done on every irq_create_of_mapping()
which happens for instance during pci enable calls. Level typed
interrupts are masked by default, edge are unmasked.
On the first ->xlate() call the level interrupt is configured and
masked. The driver calls request_irq() and the line is unmasked. Lets
assume the interrupt line is shared with another device and we call
pci_enable_device() for this device. The ->xlate() configures the pin
again and it is masked. request_irq() does not unmask the line because
it _is_ already unmasked according to its internal state. So the
interrupt will never be unmasked again.
This patch is based on an earlier work by Torben Hohn and solves the
problem by configuring the pin only once. Since all devices must agree
on the same type and polarity there is no point in configuring the pin
more than once.
[ tglx: Split out the ce4100 part into a separate patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] slub: fix panic with DISCONTIGMEM
[PARISC] set memory ranges in N_NORMAL_MEMORY when onlined
|
|
It was noticed that P4 machines were generating double NMIs for
each perf event. These extra NMIs lead to 'Dazed and confused'
messages on the screen.
I tracked this down to a P4 quirk that said the overflow bit had
to be cleared before re-enabling the apic LVT mask. My first
attempt was to move the un-masking inside the perf nmi handler
from before the chipset NMI handler to after.
This broke Nehalem boxes that seem to like the unmasking before
the counters themselves are re-enabled.
In order to keep this change simple for 2.6.39, I decided to
just simply move the apic LVT un-masking to the beginning of all
the chipset NMI handlers, with the exception of Pentium4's to
fix the double NMI issue.
Later on we can move the un-masking to later in the handlers to
save a number of 'extra' NMIs on those particular chipsets.
I tested this change on a P4 machine, an AMD machine, a Nehalem
box, and a core2quad box. 'perf top' worked correctly along
with various other small 'perf record' runs. Anything high
stress breaks all the machines but that is a different problem.
Thanks to various people for testing different versions of this
patch.
Reported-and-tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303900353-10242-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Cyrill Gorcunov <gorcunov@gmail.com>
|
|
For m68k, N_NORMAL_MEMORY represents all nodes that have present memory
since it does not support HIGHMEM. This patch sets the bit at the time
node_present_pages has been set by free_area_init_node.
At the time the node is brought online, the node state would have to be
done unconditionally since information about present memory has not yet
been recorded.
If N_NORMAL_MEMORY is not accurate, slub may encounter errors since it
uses this nodemask to setup per-cache kmem_cache_node data structures.
This pach is an alternative to the one proposed by David Rientjes
<rientjes@google.com> attempting to set node state immediately when
bringing the node online.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Tested-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: stable@kernel.org
|
|
devel-fixes
|
|
These changes were incorrectly fixed by codespell. They were now
manually corrected.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kvm-390: Let kernel exit SIE instruction on work
[S390] dasd: check sense type in device change handler
[S390] pfault: fix token handling
[S390] qdio: reset error states immediately
[S390] fix page table walk for changing page attributes
[S390] prng: prevent access beyond end of stack
[S390] dasd: fix race between open and offline
|
|
On Nehalem CPUs the retired branch-misses event can be completely bogus,
when there are no branch-misses occuring. When there are a lot of branch
misses then the count is pretty accurate. Still, this leaves us with an
event that over-counts a lot.
Detect this erratum and work it around by using BR_MISP_EXEC.ANY events.
These will also count speculated branches but still it's a lot more
precise in practice than the architectural event.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-yyfg0bxo9jsqxd6a0ovfny27@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Currently the x86 backend incorrectly assumes that any BRANCH_INSN
with sample_period==1 is a BTS request. This is not true when we do
frequency driven profiling such as 'perf record -e branches'.
Solves this error:
$ perf record -e branches ./array
Error: sys_perf_event_open() syscall returned with 95 (Operation not supported).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: "Metzger, Markus T" <markus.t.metzger@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-rd2y4ct71hjawzz6fpvsy9hg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Blindly setting 1.2V in the initial structure may not even match the
default voltages stored in the voltage table which are supported for
the domain. For example, OMAP3430 core domain does not use 1.2V and
ends up generating a warning on the first transition.
Further, since omap2_set_init_voltage is called as part of the pm
framework's initialization sequence to configure the voltage required
for the current OPP, the call does(and has to) setup the system
voltage(curr_volt as a result) using the right mechanisms appropriate
for the system at that point of time. This also overrides
initialization we are currently doing in voltage.c making it
redundant. So, remove the wrong and redundant initialization.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4 has two different Devices IVA and DSP. DSP is bound
with IVA for DVFS. The registration of IVA dev in API
'omap2_init_processor_devices' was missing. Init dev for
'iva_dev' is added.
This also fixes the following error seen during boot as
omap2_set_init_voltage can now find the iva device
omap2_set_init_voltage: Invalid parameters!
omap2_set_init_voltage: Unable to put vdd_iva to its init voltage
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
So that omap_vram_set_sdram_vram() is called before
omap_vram_reserve_sdram_memblock().
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If an error occurs in the L3 on any other initiator than MPU,
the interrupt goes unhandled given that the 'base' register
was calculated with the initialized err_source value (which
coincidentally points to MPU) and not with the actual source
of the error.
Removed parenthesis that are not needed for the touched lines.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This fixes broken build when using binutils 2.21.
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
rtc: fix coh901331 startup crash
mach-ux500: fix i2c0 device setup regression
|
|
When we use BIOS function e801 to probe memory, we should use ax/bx
(or cx/dx) as a pair, not mix and match. This was a typo during the
translation from assembly code, and breaks at least one set of
machines in the field (which return cx = dx = 0).
Reported-and-tested-by: Chris Samuel <chris@csamuel.org>
Fix-proposed-by: Thomas Meyer <thomas@m3y3r.de>
Link: http://lkml.kernel.org/r/1303566747.12067.10.camel@localhost.localdomain
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Add missing syscore_suspend() and syscore_resume() calls
PM: Fix error code paths executed after failing syscore_suspend()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix unused warnings when !SND_HDA_NEEDS_RESUME
ALSA: hda - Add a fix-up for Acer dmic with ALC271x codec
ASoC: add a module alias to the FSI driver
ALSA: emu10k1 - Fix "Music" controls to "Synth" controls in documents
ARM: s3c2440: gta02; Register dfbmcs320 device for BT audio interface
ASoC: codecs: JZ4740: Fix OOPS
ASoC: Fix output PGA enabling in wm_hubs CODECs
ASoC: sn95031: decorate function with __devexit_p()
ASoC: SAMSUNG: Fix the inverted clocks handling for pcm driver
ASoC: sst_platform: Fix lock acquring
ASoC: fsi: driver safely remove for against irq
ASoC: fsi: modify vague PM control on probe
ASoC: fsi: take care in failing case of dai register
MAINTAINERS: Update Samsung ASoC maintainer's id
ASoC: WM8903: HP and Line out PGA/mixer DAPM fixes
ASoC: Set left channel volume update bits for WM8994
ASoC: fix config error path
ASoC: check channel mismatch between cpu_dai and codec_dai
ASoC: Tegra: Suspend/resume support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Update/fix Intel Nehalem cache events
perf, x86: P4 PMU - Don't forget to clear cpuc->active_mask on overflow
x86, perf event: Turn off unstructured raw event access to offcore registers
perf: Support Xeon E7's via the Westmere PMU driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xtensa: Fixup irq conversion fallout and nmi_count
|
|
Change the Nehalem cache events to use retired memory instruction counters
(similar to Westmere), this greatly improves the provided stats.
Using:
main ()
{
int i;
for (i = 0; i < 1000000000; i++) {
asm("mov (%%rsp), %%rbx;"
"mov %%rbx, (%%rsp);" : : : "rbx");
}
}
We find:
$ perf stat --repeat 10 -e instructions:u -e l1-dcache-loads:u -e l1-dcache-stores:u ./loop_1b_loads+stores
Performance counter stats for './loop_1b_loads+stores' (10 runs):
4,000,081,056 instructions:u # 0.000 IPC ( +- 0.000% )
4,999,502,846 l1-dcache-loads:u ( +- 0.008% )
1,000,034,832 l1-dcache-stores:u ( +- 0.000% )
1.565184942 seconds time elapsed ( +- 0.005% )
The 5b is surprising - we'd expect 1b:
$ perf stat --repeat 10 -e instructions:u -e r10b:u -e l1-dcache-stores:u ./loop_1b_loads+stores
Performance counter stats for './loop_1b_loads+stores' (10 runs):
4,000,081,054 instructions:u # 0.000 IPC ( +- 0.000% )
1,000,021,961 r10b:u ( +- 0.000% )
1,000,030,951 l1-dcache-stores:u ( +- 0.000% )
1.565055422 seconds time elapsed ( +- 0.003% )
Which this patch thus fixes.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Link: http://lkml.kernel.org/n/tip-q9rtru7b7840tws75xzboapv@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
It's not enough to simply disable event on overflow the
cpuc->active_mask should be cleared as well otherwise counter
may stall in "active" even in real being already disabled (which
potentially may lead to the situation that user may not use this
counter further).
Don pointed out that:
" I also noticed this patch fixed some unknown NMIs
on a P4 when I stressed the box".
Tested-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303398203-2918-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Andi Kleen pointed out that the Intel offcore support patches were merged
without user-space tool support to the functionality:
|
| The offcore_msr perf kernel code was merged into 2.6.39-rc*, but the
| user space bits were not. This made it impossible to set the extra mask
| and actually do the OFFCORE profiling
|
Andi submitted a preliminary patch for user-space support, as an
extension to perf's raw event syntax:
|
| Some raw events -- like the Intel OFFCORE events -- support additional
| parameters. These can be appended after a ':'.
|
| For example on a multi socket Intel Nehalem:
|
| perf stat -e r1b7:20ff -a sleep 1
|
| Profile the OFFCORE_RESPONSE.ANY_REQUEST with event mask REMOTE_DRAM_0
| that measures any access to DRAM on another socket.
|
But this kind of usability is absolutely unacceptable - users should not
be expected to type in magic, CPU and model specific incantations to get
access to useful hardware functionality.
The proper solution is to expose useful offcore functionality via
generalized events - that way users do not have to care which specific
CPU model they are using, they can use the conceptual event and not some
model specific quirky hexa number.
We already have such generalization in place for CPU cache events,
and it's all very extensible.
"Offcore" events measure general DRAM access patters along various
parameters. They are particularly useful in NUMA systems.
We want to support them via generalized DRAM events: either as the
fourth level of cache (after the last-level cache), or as a separate
generalization category.
That way user-space support would be very obvious, memory access
profiling could be done via self-explanatory commands like:
perf record -e dram ./myapp
perf record -e dram-remote ./myapp
... to measure DRAM accesses or more expensive cross-node NUMA DRAM
accesses.
These generalized events would work on all CPUs and architectures that
have comparable PMU features.
( Note, these are just examples: actual implementation could have more
sophistication and more parameter - as long as they center around
similarly simple usecases. )
Now we do not want to revert *all* of the current offcore bits, as they
are still somewhat useful for generic last-level-cache events, implemented
in this commit:
e994d7d23a0b: perf: Fix LLC-* events on Intel Nehalem/Westmere
But we definitely do not yet want to expose the unstructured raw events
to user-space, until better generalization and usability is implemented
for these hardware event features.
( Note: after generalization has been implemented raw offcore events can be
supported as well: there can always be an odd event that is marginally
useful but not useful enough to generalize. DRAM profiling is definitely
*not* such a category so generalization must be done first. )
Furthermore, PERF_TYPE_RAW access to these registers was not intended
to go upstream without proper support - it was a side-effect of the above
e994d7d23a0b commit, not mentioned in the changelog.
As v2.6.39 is nearing release we go for the simplest approach: disable
the PERF_TYPE_RAW offcore hack for now, before it escapes into a released
kernel and becomes an ABI.
Once proper structure is implemented for these hardware events and users
are offered usable solutions we can revisit this issue.
Reported-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302658203-4239-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
There's a new model number public, 47, for Xeon E7 (aka Westmere EX).
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: a.p.zijlstra@chello.nl
Link: http://lkml.kernel.org/r/1303429715-10202-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When a DISCONTIGMEM memory range is brought online as a NUMA node, it
also needs to have its bet set in N_NORMAL_MEMORY. This is necessary for
generic kernel code that utilizes N_NORMAL_MEMORY as a subset of N_ONLINE
for memory savings.
These types of hacks can hopefully be removed once DISCONTIGMEM is either
removed or abstracted away from CONFIG_NUMA.
Fixes a panic in the slub code which only initializes structures for
N_NORMAL_MEMORY to save memory:
Backtrace:
[<000000004021c938>] add_partial+0x28/0x98
[<000000004021faa0>] __slab_free+0x1d0/0x1d8
[<000000004021fd04>] kmem_cache_free+0xc4/0x128
[<000000004033bf9c>] ida_get_new_above+0x21c/0x2c0
[<00000000402a8980>] sysfs_new_dirent+0xd0/0x238
[<00000000402a974c>] create_dir+0x5c/0x168
[<00000000402a9ab0>] sysfs_create_dir+0x98/0x128
[<000000004033d6c4>] kobject_add_internal+0x114/0x258
[<000000004033d9ac>] kobject_add_varg+0x7c/0xa0
[<000000004033df20>] kobject_add+0x50/0x90
[<000000004033dfb4>] kobject_create_and_add+0x54/0xc8
[<00000000407862a0>] cgroup_init+0x138/0x1f0
[<000000004077ce50>] start_kernel+0x5a0/0x840
[<000000004011fa3c>] start_parisc+0xa4/0xb8
[<00000000404bb034>] packet_ioctl+0x16c/0x208
[<000000004049ac30>] ip_mroute_setsockopt+0x260/0xf20
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The cpu<->node mappings under CONFIG_DEBUG_PER_CPU_MAPS=y
when NUMA emulation is enabled is currently broken because it does
not iterate through every emulated node and bind cpus that have
affinity to it.
NUMA emulation should bind each cpu to every local node to
accurately represent the true NUMA topology of the underlying
machine.
debug_cpumask_set_cpu() needs to be fixed at the same time so
that the debugging information that it emits shows the new
cpumask of the node being assigned when the cpu is being added
or removed.
It can now take responsibility of setting or clearing the cpu
itself to remove the need for duplicate code.
Also change its last parameter, "enable", to have the correct bool
type since it can only be true or false.
-v2: Fix the return statements, by Kosaki Motohiro
Acked-and-Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918470.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Andreas Herrmann reported that 7d6b46707f24 ("x86, NUMA: Fix fakenuma
boot failure") causes certain physical NUMA topologies (for example
AMD Magny-Cours) to move sibling cpus to a single node when in reality
they are in separate domains.
This may result in some nodes being completely void of cpus, which
doesn't accurately represent the correct topology. The system will
boot, but will have suboptimal NUMA performance.
This commit was intended as a fix for NUMA emulation, but should
not cause a regression for real NUMA machines as a side effect.
( There will be a separate fix for the numa-debug code, which
will not affect physical topologies. )
Reported-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918110.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6881/1: cputype.h uses __attribute_const__ which requires including kernel.h
ARM: Add new syscalls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug-fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mask_rw_pte: do not apply the early_ioremap checks on x86_32
xen: do not create the extra e820 region at an addr lower than 4G
|
|
GPIO module expects the debounce clocks to be enabled during reset. It doesn't
reset properly and timeouts are seen, if this clock isn't enabled during
reset. Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flags to the GPIO HWMODs, with
which the debounce clocks are enabled during reset.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
As per OMAP3 erratum (i671), ROM code adds extra latencies while
restoring CM_AUTOIDLE_PLL register, if AUTO_PERIPH_DPLL is equal to 1.
This patch stores 0's in scratchpad content area corresponding to
AUTO_PERIPH_DPLL, to prevent ROM code to try to lock per DPLL, since
it won't respect proper programing scheme.
This register is then stored in prcm context. The saving and restore
is now done by kernel side.
Here follow the erratum description
DESCRIPTION
After OFF mode transition, among many restorations, the ROM Code restores the
CM_AUTOIDLE_PLL register, and after that, it tries to relock the PER DPLL.
In case the restoration data stored in scratchpad memory contains a field
CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL = 1, then the way the ROM Code restores and
locks the PER DPLL does not respect the PER DPLL programming scheme.
In that case, the DPLL might not lock. Meanwhile, when trying to lock the PER
DPLL, the ROM Code does not hang. Only extra latencies are introduced at
wake-up.
WORKAROUND
When saving the context-restore structure in scratchpad memory, in order to
respect the PER DPLL programming scheme, it is advised to store 0 in the
CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL field of the saved structure.
After wake-up, the application should store in CM_AUTOIDLE_PLL register the
right desired value.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The saving of CCR.CM_AUTOIDLE_PLL is done in scratchpad area.
However, in current code, the saving is done for CM_AUTOIDLE2_PLL
(offset 0x34) instead of CM_AUTOIDLE_PLL (offset 0x30).
This patch changes the code to save the correct register.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
DSS driver has used fck and ick clocks on OMAP2/3 to get DSS HW up and
running, and also to get the pixel clock's source clock rate from the
fck.
On OMAP4 the clock data is set up in a different way, as there's no ick,
dss_fck points to a fake clock which just affects DSS's MODULEMODE, and
dss_dss_clk if the DSS_FCK.
>From DSS driver's point of view the dss_fck sounds like an ick, and
dss_dss_clk is the fck. While this is not entirely correct from HW point
of view, especially for the ick, configuring the clock aliases that way
makes DSS "just work" with OMAP4's clock setup.
In the (hopefully near) future DSS driver will be reworked to use
pm_runtime support which should clean up the clock code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Adding two sets of I2C devices to the same bus doesn't quite work,
atleast not anymore. Stash one array and determine how much of it
shall be added instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The two "is_early_ioremap_ptep" checks in mask_rw_pte are only used on
x86_64, in fact early_ioremap is not used at all to setup the initial
pagetable on x86_32.
Moreover on x86_32 the two checks are wrong because the range
pgt_buf_start..pgt_buf_end initially should be mapped RW because
the pages in the range are not pagetable pages yet and haven't been
cleared yet. Afterwards considering the pgt_buf_start..pgt_buf_end is
part of the initial mapping, xen_alloc_pte is capable of turning
the ptes RO when they become pagetable pages.
Fix the issue and improve the readability of the code providing two
different implementation of mask_rw_pte for x86_32 and x86_64.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Do not add the extra e820 region at a physical address lower than 4G
because it breaks e820_end_of_low_ram_pfn().
It is OK for us to move the xen_extra_mem_start up and down because this
is the index of the memory that can be ballooned in/out - it is memory
not available to the kernel during bootup.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
From: Christian Borntraeger <borntraeger@de.ibm.com>
This patch fixes the sie exit on interrupts. The low level
interrupt handler returns to the PSW address in pt_regs and not
to the PSW address in the lowcore.
Without this fix a cpu bound guest might never leave guest state
since the host interrupt handler would blindly return to the
SIE instruction, even on need_resched and friends.
Cc: stable@kernel.org
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
f6649a7e "[S390] cleanup lowcore access from external interrupts" changed
handling of external interrupts. Instead of letting the external interrupt
handlers accessing the per cpu lowcore the entry code of the kernel reads
already all fields that are necessary and passes them to the handlers.
The pfault interrupt handler was incorrectly converted. It tries to
dereference a value which used to be a pointer to a lowcore field. After
the conversion however it is not anymore the pointer to the field but its
content. So instead of a dereference only a cast is needed to get the
task pointer that caused the pfault.
Fixes a NULL pointer dereference and a subsequent kernel crash:
Unable to handle kernel pointer dereference at virtual kernel address (null)
Oops: 0004 [#1] SMP
Modules linked in: nfsd exportfs nfs lockd fscache nfs_acl auth_rpcgss sunrpc
loop qeth_l3 qeth vmur ccwgroup ext3 jbd mbcache dm_mod
dasd_eckd_mod dasd_diag_mod dasd_mod
CPU: 0 Not tainted 2.6.38-2-s390x #1
Process cron (pid: 1106, task: 000000001f962f78, ksp: 000000001fa0f9d0)
Krnl PSW : 0404200180000000 000000000002c03e (pfault_interrupt+0xa2/0x138)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
Krnl GPRS: 0000000000000000 0000000000000001 0000000000000000 0000000000000001
000000001f962f78 0000000000518968 0000000090000002 000000001ff03280
0000000000000000 000000000064f000 000000001f962f78 0000000000002603
0000000006002603 0000000000000000 000000001ff7fe68 000000001ff7fe48
Krnl Code: 000000000002c036: 5820d010 l %r2,16(%r13)
000000000002c03a: 1832 lr %r3,%r2
000000000002c03c: 1a31 ar %r3,%r1
>000000000002c03e: ba23d010 cs %r2,%r3,16(%r13)
000000000002c042: a744fffc brc 4,2c03a
000000000002c046: a7290002 lghi %r2,2
000000000002c04a: e320d0000024 stg %r2,0(%r13)
000000000002c050: 07f0 bcr 15,%r0
Call Trace:
([<000000001f962f78>] 0x1f962f78)
[<000000000001acda>] do_extint+0xf6/0x138
[<000000000039b6ca>] ext_no_vtime+0x30/0x34
[<000000007d706e04>] 0x7d706e04
Last Breaking-Event-Address:
[<0000000000000000>] 0x0
For stable maintainers:
the first kernel which contains this bug is 2.6.37.
Reported-by: Stephen Powell <zlinuxman@wowway.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The page table walk for changing page attributes used the wrong
address for pgd/pud/pmd lookups if the range was bigger than
a pmd entry. Fix the lookup by using the correct address.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
While initializing the state of the prng only the first 8 bytes of
random data where used, the second 8 bytes were read from the memory
after the stack. If only 64 bytes of the kernel stack are used and
CONFIG_DEBUG_PAGEALLOC is enabled a kernel panic may occur because of
the invalid page access. Use the correct multiplicator to stay within
the random data buffer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Device suspend/resume infrastructure is used not only by the suspend
and hibernate code in kernel/power, but also by APM, Xen and the
kexec jump feature. However, commit 40dc166cb5dddbd36aa4ad11c03915ea
(PM / Core: Introduce struct syscore_ops for core subsystems PM)
failed to add syscore_suspend() and syscore_resume() calls to that
code, which generally leads to breakage when the features in question
are used.
To fix this problem, add the missing syscore_suspend() and
syscore_resume() calls to arch/x86/kernel/apm_32.c, kernel/kexec.c
and drivers/xen/manage.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
|
|
Some unnamed moron fatfingered the arguments of the irq chip callbacks
to irq_chip instead of irq_data.
While at it remove the nmi_count() print in arch_show_interrupts()
which has been broken before the irq conversion already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
