| Age | Commit message (Collapse) | Author |
|---|
|
This patches adds an "install" target to install kernel builds for SPARC,
modeled after the i386 script.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit is a guesswork, but it seems to make sense to drop this
break, as otherwise the following line is never executed and becomes
dead code. And that following line actually saves the result of
local calculation by the pointer given in function argument. So the
proposed change makes sense if this code in the whole makes sense (but I
am unable to analyze it in the whole).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81641
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LDC handshake could have been asynchronously triggered
after ldc_bind() enables the ldc_rx() receive interrupt-handler
(and thus intercepts incoming control packets)
and before vio_port_up() calls ldc_connect(). If that is the case,
ldc_connect() should return 0 and let the state-machine
progress.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based almost entirely upon a patch by Christopher Alexander Tobias
Schulze.
In commit db64fe02258f1507e13fe5212a989922323685ce ("mm: rewrite vmap
layer") lazy VMAP tlb flushing was added to the vmalloc layer. This
causes problems on sparc64.
Sparc64 has two VMAP mapped regions and they are not contiguous with
eachother. First we have the malloc mapping area, then another
unrelated region, then the vmalloc region.
This "another unrelated region" is where the firmware is mapped.
If the lazy TLB flushing logic in the vmalloc code triggers after
we've had both a module unload and a vfree or similar, it will pass an
address range that goes from somewhere inside the malloc region to
somewhere inside the vmalloc region, and thus covering the
openfirmware area entirely.
The sparc64 kernel learns about openfirmware's dynamic mappings in
this region early in the boot, and then services TLB misses in this
area. But openfirmware has some locked TLB entries which are not
mentioned in those dynamic mappings and we should thus not disturb
them.
These huge lazy TLB flush ranges causes those openfirmware locked TLB
entries to be removed, resulting in all kinds of problems including
hard hangs and crashes during reboot/reset.
Besides causing problems like this, such huge TLB flush ranges are
also incredibly inefficient. A plea has been made with the author of
the VMAP lazy TLB flushing code, but for now we'll put a safety guard
into our flush_tlb_kernel_range() implementation.
Since the implementation has become non-trivial, stop defining it as a
macro and instead make it a function in a C source file.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The assumption was that update_mmu_cache() (and the equivalent for PMDs) would
only be called when the PTE being installed will be accessible by the user.
This is not true for code paths originating from remove_migration_pte().
There are dire consequences for placing a non-valid PTE into the TSB. The TLB
miss frramework assumes thatwhen a TSB entry matches we can just load it into
the TLB and return from the TLB miss trap.
So if a non-valid PTE is in there, we will deadlock taking the TLB miss over
and over, never satisfying the miss.
Just exit early from update_mmu_cache() and friends in this situation.
Based upon a report and patch from Christopher Alexander Tobias Schulze.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM AES crypto fixes from Herbert Xu:
"This push fixes a regression on ARM where odd-sized blocks supplied to
AES may cause crashes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm-aes - fix encryption of unaligned data
crypto: arm64-aes - fix encryption of unaligned data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 more small powerpc fixes that should still go into .16.
One is a recent regression (MMCR2 business), the other is a trivial
endian fix without which FW updates won't work on LE in IBM machines,
and the 3rd one turns a BUG_ON into a WARN_ON which is definitely a
LOT more friendly especially when the whole thing is about retrieving
error logs ..."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix endianness of flash_block_list in rtas_flash
powerpc/powernv: Change BUG_ON to WARN_ON in elog code
powerpc/perf: Fix MMCR2 handling for EBB
|
|
Fix the same alignment bug as in arm64 - we need to pass residue
unprocessed bytes as the last argument to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.13+
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
cryptsetup fails on arm64 when using kernel encryption via AF_ALG socket.
See https://bugzilla.redhat.com/show_bug.cgi?id=1122937
The bug is caused by incorrect handling of unaligned data in
arch/arm64/crypto/aes-glue.c. Cryptsetup creates a buffer that is aligned
on 8 bytes, but not on 16 bytes. It opens AF_ALG socket and uses the
socket to encrypt data in the buffer. The arm64 crypto accelerator causes
data corruption or crashes in the scatterwalk_pagedone.
This patch fixes the bug by passing the residue bytes that were not
processed as the last parameter to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The function rtas_flash_firmware passes the address of a data structure,
flash_block_list, when making the update-flash-64-and-reboot rtas call.
While the endianness of the address is handled correctly, the endianness
of the data is not. This patch ensures that the data in flash_block_list
is big endian when passed to rtas on little endian hosts.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We can continue to read the error log (up to MAX size) even if
we get the elog size more than MAX size. Hence change BUG_ON to
WARN_ON.
Also updated error message.
Reported-by: Gopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A bunch of fixes for perf and kprobes:
- revert a commit that caused a perf group regression
- silence dmesg spam
- fix kprobe probing errors on ia64 and ppc64
- filter kprobe faults from userspace
- lockdep fix for perf exit path
- prevent perf #GP in KVM guest
- correct perf event and filters"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Fix "Failed to find blacklist" probing errors on ia64 and ppc64
kprobes/x86: Don't try to resolve kprobe faults from userspace
perf/x86/intel: Avoid spamming kernel log for BTS buffer failure
perf/x86/intel: Protect LBR and extra_regs against KVM lying
perf: Fix lockdep warning on process exit
perf/x86/intel/uncore: Fix SNB-EP/IVT Cbox filter mappings
perf/x86/intel: Use proper dTLB-load-misses event on IvyBridge
perf: Revert ("perf: Always destroy groups on exit")
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A couple of crash fixes, plus a fix that on 32 bits would cause a
missing -ENOSYS for nonexistent system calls"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Fix cache topology for early P4-SMT
x86_32, entry: Store badsys error code in %eax
x86, MCE: Robustify mcheck_init_device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin fixes from Steven Miao:
"smc nor flash PM fix, pinctrl group fix, update defconfig, and build
fixes"
* tag 'blackfin-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
blackfin: vmlinux.lds.S: reserve 32 bytes space at the end of data section for XIP kernel
defconfig: BF609: update spi config name
irq: blackfin sec: drop duplicated sec priority set
blackfin: bind different groups of one pinmux function to different state name
blackfin: fix some bf5xx boards build for missing <linux/gpio.h>
pm: bf609: cleanup smc nor flash
|
|
for XIP kernel
to collect some undefined section to the end of the data section and avoid section overlap
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
drop smc pin state change code, pin state will be saved in pinctrl-adi2 driver
cleanup nor flash init/exit for pm suspend/resume
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Promote one fix for 3.16
This fix was necessary after
9c15a24b038f ("x86/mce: Improve mcheck_init_device() error handling")
went in. What this patch did was, among others, check the return value
of misc_register and exit early if it encountered an error. Original
code sloppily didn't do that.
However,
cef12ee52b05 ("xen/mce: Add mcelog support for Xen platform")
made it so that xen's init routine xen_late_init_mcelog runs first. This
was needed for the xen mcelog device which is supposed to be independent
from the baremetal one.
Initially it was reported that misc_register() fails often on xen and
that's why it needed fixing. However, it is *supposed* to fail by
design, when running in dom0 so that the xen mcelog device file gets
registered first.
And *then* you need the notifier *not* unregistered on the error path so
that the timer does get deleted properly in the CPU hotplug notifier.
Btw, this fix is needed also on baremetal in the unlikely event that
misc_register(&mce_chrdev_device) fails there too.
I was unsure whether to rush it in now and decided to delay it to 3.17.
However, xen people wanted it promoted as it breaks xen when doing cpu
hotplug there. So, after a bit of simmering in tip/master for initial
smoke testing, let's move it to 3.16. It fixes a semi-regression which
got introduced in 3.16 so no need for stable tagging.
tip/x86/ras contains that exact same commit but we can't remove it
there as it is not the last one. It won't cause any merge issues, as I
confirmed locally but I should state here the special situation of this
one fix explicitly anyway.
Thanks.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
alloc_bootmem and related function always return zeroed region of
memory. Thus a memset after calls to these functions is unnecessary.
The following Coccinelle semantic patch was used for making the change:
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The sa_restorer field in struct sigaction is obsolete and no longer in
the parisc implementation. However, the core code assumes the field is
present if SA_RESTORER is defined. So, the define needs to be removed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Fix arm64 regression introduced by limiting the CMA buffer to ZONE_DMA
on platforms where RAM starts above 4GB (and ZONE_DMA becoming 0)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Create non-empty ZONE_DMA when DRAM starts above 4GB
|
|
Pull Xtensa fixes from Chris Zankel:
- resolve FIXMEs in double exception handler for window overflow. This
fix makes native building of linux on xtensa host possible;
- fix sysmem region removal issue introduced in 3.15.
* tag 'xtensa-next-20140721' of git://github.com/czankel/xtensa-linux:
xtensa: fix sysmem reservation at the end of existing block
xtensa: add fixup for double exception raised in window overflow
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here is a handful of powerpc fixes for 3.16. They are all pretty
simple and self contained and should still make this release"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: use _GLOBAL_TOC for memmove
powerpc/pseries: dynamically added OF nodes need to call of_node_init
powerpc: subpage_protect: Increase the array size to take care of 64TB
powerpc: Fix bugs in emulate_step()
powerpc: Disable doorbells on Power8 DD1.x
|
|
When compiling a SH2A kernel (e.g. se7206_defconfig or rsk7203_defconfig)
using sh4-linux-gcc, linking fails with:
net/built-in.o: In function `__sk_run_filter':
net/core/filter.c:566: undefined reference to `__fpscr_values'
net/core/filter.c:269: undefined reference to `__fpscr_values'
...
net/built-in.o:net/core/filter.c:580: more undefined references to `__fpscr_values' follow
This happens because sh4-linux-gcc doesn't support the "-m2a-nofpu",
which is thus filtered out by "$(call cc-option, ...)".
As compiling using sh4-linux-gcc is useful for compile coverage, also
try passing "-m4-nofpu" (which is presumably filtered out when using a
real sh2a-linux toolchain) to disable the generation of FPU instructions
and references to __fpscr_values[].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
P4 systems with cpuid level < 4 can have SMT, but the cache topology
description available (cpuid2) does not include SMP information.
Now we know that SMT shares all cache levels, and therefore we can
mark all available cache levels as shared.
We do this by setting cpu_llc_id to ->phys_proc_id, since that's
the same for each SMT thread. We can do this unconditional since if
there's no SMT its still true, the one CPU shares cache with only
itself.
This fixes a problem where such CPUs report an incorrect LLC CPU mask.
This in turn fixes a crash in the scheduler where the topology was
build wrong, it assumes the LLC mask to include at least the SMT CPUs.
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140722133514.GM12054@laptop.lan
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
ZONE_DMA is created to allow 32-bit only devices to access memory in the
absence of an IOMMU. On systems where the memory starts above 4GB, it is
expected that some devices have a DMA offset hardwired to be able to
access the bottom of the memory. Linux currently supports DT bindings
for the DMA offsets but they are not (easily) available early during
boot.
This patch tries to guess a DMA offset and assumes that ZONE_DMA
corresponds to the 32-bit mask above the start of DRAM.
Fixes: 2d5a5612bc (arm64: Limit the CMA buffer to 32-bit if ZONE_DMA)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Tested-by: Anup Patel <anup.patel@linaro.org>
|
|
In the recent commit b50a6c584bb4 "Clear MMCR2 when enabling PMU", I
screwed up the handling of MMCR2 for tasks using EBB.
We must make sure we set MMCR2 *before* ebb_switch_in(), otherwise we
overwrite the value of MMCR2 that userspace may have written. That
potentially breaks a task that uses EBB and manually uses MMCR2 for
event freezing.
Fixes: b50a6c584bb4 ("powerpc/perf: Clear MMCR2 when enabling PMU")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 554086d ("x86_32, entry: Do syscall exit work on badsys
(CVE-2014-4508)") introduced a regression in the x86_32 syscall entry
code, resulting in syscall() not returning proper errors for undefined
syscalls on CPUs supporting the sysenter feature.
The following code:
> int result = syscall(666);
> printf("result=%d errno=%d error=%s\n", result, errno, strerror(errno));
results in:
> result=666 errno=0 error=Success
Obviously, the syscall return value is the called syscall number, but it
should have been an ENOSYS error. When run under ptrace it behaves
correctly, which makes it hard to debug in the wild:
> result=-1 errno=38 error=Function not implemented
The %eax register is the return value register. For debugging via ptrace
the syscall entry code stores the complete register context on the
stack. The badsys handlers only store the ENOSYS error code in the
ptrace register set and do not set %eax like a regular syscall handler
would. The old resume_userspace call chain contains code that clobbers
%eax and it restores %eax from the ptrace registers afterwards. The same
goes for the ptrace-enabled call chain. When ptrace is not used, the
syscall return value is the passed-in syscall number from the untouched
%eax register.
Use %eax as the return value register in syscall_badsys and
sysenter_badsys, like a real syscall handler does, and have the caller
push the value onto the stack for ptrace access.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.11.1407221022380.31021@titan.int.lan.stealer.net
Reviewed-and-tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: <stable@vger.kernel.org> # If 554086d is backported
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
memmove may be called from module code copy_pages(btrfs), and it may
call memcpy, which may call back to C code, so it needs to use
_GLOBAL_TOC to set up r2 correctly.
This fixes following error when I tried to boot an le guest:
Vector: 300 (Data Access) at [c000000073f97210]
pc: c000000000015004: enable_kernel_altivec+0x24/0x80
lr: c000000000058fbc: enter_vmx_copy+0x3c/0x60
sp: c000000073f97490
msr: 8000000002009033
dar: d000000001d50170
dsisr: 40000000
current = 0xc0000000734c0000
paca = 0xc00000000fff0000 softe: 0 irq_happened: 0x01
pid = 815, comm = mktemp
enter ? for help
[c000000073f974f0] c000000000058fbc enter_vmx_copy+0x3c/0x60
[c000000073f97510] c000000000057d34 memcpy_power7+0x274/0x840
[c000000073f97610] d000000001c3179c copy_pages+0xfc/0x110 [btrfs]
[c000000073f97660] d000000001c3c248 memcpy_extent_buffer+0xe8/0x160 [btrfs]
[c000000073f97700] d000000001be4be8 setup_items_for_insert+0x208/0x4a0 [btrfs]
[c000000073f97820] d000000001be50b4 btrfs_insert_empty_items+0xf4/0x140 [btrfs]
[c000000073f97890] d000000001bfed30 insert_with_overflow+0x70/0x180 [btrfs]
[c000000073f97900] d000000001bff174 btrfs_insert_dir_item+0x114/0x2f0 [btrfs]
[c000000073f979a0] d000000001c1f92c btrfs_add_link+0x10c/0x370 [btrfs]
[c000000073f97a40] d000000001c20e94 btrfs_create+0x204/0x270 [btrfs]
[c000000073f97b00] c00000000026d438 vfs_create+0x178/0x210
[c000000073f97b50] c000000000270a70 do_last+0x9f0/0xe90
[c000000073f97c20] c000000000271010 path_openat+0x100/0x810
[c000000073f97ce0] c000000000272ea8 do_filp_open+0x58/0xd0
[c000000073f97dc0] c00000000025ade8 do_sys_open+0x1b8/0x300
[c000000073f97e30] c00000000000a008 syscall_exit+0x0/0x7c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 75b57ecf9 refactored device tree nodes to use kobjects such that they
can be exposed via /sysfs. A secondary commit 0829f6d1f furthered this rework
by moving the kobect initialization logic out of of_node_add into its own
of_node_init function. The inital commit removed the existing kref_init calls
in the pseries dlpar code with the assumption kobject initialization would
occur in of_node_add. The second commit had the side effect of triggering a
BUG_ON during DLPAR, migration and suspend/resume operations as a result of
dynamically added nodes being uninitialized.
This patch fixes this by adding of_node_init calls in place of the previously
removed kref_init calls.
Fixes: 0829f6d1f69e ("of: device_node kobject lifecycle fixes")
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We now support TASK_SIZE of 16TB, hence the array should be 8.
Fixes the below crash:
Unable to handle kernel paging request for data at address 0x000100bd
Faulting instruction address: 0xc00000000004f914
cpu 0x13: Vector: 300 (Data Access) at [c000000fea75fa90]
pc: c00000000004f914: .sys_subpage_prot+0x2d4/0x5c0
lr: c00000000004fb5c: .sys_subpage_prot+0x51c/0x5c0
sp: c000000fea75fd10
msr: 9000000000009032
dar: 100bd
dsisr: 40000000
current = 0xc000000fea6ae490
paca = 0xc00000000fb8ab00 softe: 0 irq_happened: 0x00
pid = 8237, comm = a.out
enter ? for help
[c000000fea75fe30] c00000000000a164 syscall_exit+0x0/0x98
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This fixes some bugs in emulate_step(). First, the setting of the carry
bit for the arithmetic right-shift instructions was not correct on 64-bit
machines because we were masking with a mask of type int rather than
unsigned long. Secondly, the sld (shift left doubleword) instruction was
using the wrong instruction field for the register containing the shift
count.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These processors do not currently support doorbell IPIs, so remove them
from the feature list if we are at DD 1.xx for the 0x004d part.
This fixes a regression caused by d4e58e5928f8 (powerpc/powernv: Enable
POWER8 doorbell IPIs). With that patch the kernel would hang at boot
when calling smp_call_function_many, as the doorbell would not be
received by the target CPUs:
.smp_call_function_many+0x2bc/0x3c0 (unreliable)
.on_each_cpu_mask+0x30/0x100
.cpuidle_register_driver+0x158/0x1a0
.cpuidle_register+0x2c/0x110
.powernv_processor_idle_init+0x23c/0x2c0
.do_one_initcall+0xd4/0x260
.kernel_init_freeable+0x25c/0x33c
.kernel_init+0x1c/0x120
.ret_from_kernel_thread+0x58/0x7c
Fixes: d4e58e5928f8 (powerpc/powernv: Enable POWER8 doorbell IPIs)
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Pull sparc fix from David Miller:
"Need to hook up the new renameat2 system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Hook up renameat2 syscall.
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm fixes from Paolo Bonzini:
"These are mostly PPC changes for 3.16-new things. However, there is
an x86 change too and it is a regression from 3.14. As it only
affects nested virtualization and there were other changes in this
area in 3.16, I am not nominating it for 3.15-stable"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Check for nested events if there is an injectable interrupt
KVM: PPC: RTAS: Do byte swaps explicitly
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
PPC: Add _GLOBAL_TOC for 32bit
KVM: PPC: BOOK3S: HV: Use base page size when comparing against slb value
KVM: PPC: Book3E: Unlock mmu_lock when setting caching atttribute
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of last minute bug fixes for 3.16, including a fix for ptrace
to close a hole which allowed a user space program to write to the
kernel address space"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix restore of invalid floating-point-control
s390/zcrypt: improve device probing for zcrypt adapter cards
s390/ptrace: fix PSW mask check
s390/MSI: Use standard mask and unmask funtions
s390/3270: correct size detection with the read-partition command
s390: require mvcos facility, not tod clock steering facility
|
|
BorisO reports that misc_register() fails often on xen. The current code
unregisters the CPU hotplug notifier in that case. If then a CPU is
offlined and onlined back again, we end up with a second timer running
on that CPU, leading to soft lockups and system hangs.
So let's leave the hotcpu notifier always registered - even if
mce_device_create failed for some cores and never unreg it so that we
can deal with the timer handling accordingly.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1403274493-1371-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
...otherwise me lose user mode regs and the resulting
stack trace is useless.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
If do_ops() fails we have to release current->mm->mmap_sem
otherwise the failing task will never terminate.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Trinity discovered an execution path such that a task
can unmap his stub page.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This reverts commit 0974a9cadc7886f7baaa458bb0c89f5c5f9d458e.
The real for for that issue is to release current->mm->mmap_sem in
fix_range_common().
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"The locking department delivers:
- A rather large and intrusive bundle of fixes to address serious
performance regressions introduced by the new rwsem / mcs
technology. Simpler solutions have been discussed, but they would
have been ugly bandaids with more risk than doing the right thing.
- Make the rwsem spin on owner technology opt-in for architectures
and enable it only on the known to work ones.
- A few fixes to the lockdep userspace library"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Add CONFIG_RWSEM_SPIN_ON_OWNER
locking/mutex: Disable optimistic spinning on some architectures
locking/rwsem: Reduce the size of struct rw_semaphore
locking/rwsem: Rename 'activity' to 'count'
locking/spinlocks/mcs: Micro-optimize osq_unlock()
locking/spinlocks/mcs: Introduce and use init macro and function for osq locks
locking/spinlocks/mcs: Convert osq lock to atomic_t to reduce overhead
locking/spinlocks/mcs: Rename optimistic_spin_queue() to optimistic_spin_node()
locking/rwsem: Allow conservative optimistic spinning when readers have lock
tools/liblockdep: Account for bitfield changes in lockdeps lock_acquire
tools/liblockdep: Remove debug print left over from development
tools/liblockdep: Fix comparison of a boolean value with a value of 2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A smaller set of fixes this week, and all regression fixes:
- a handful of issues fixed on at91 with common clock conversion
- a set of fixes for Marvell mvebu (SMP, coherency, PM)
- a clock fix for i.MX6Q.
- ... and a SMP/hotplug fix for Exynos"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
ARM: clk-imx6q: parent lvds_sel input from upstream clock gates
ARM: mvebu: Fix coherency bus notifiers by using separate notifiers
ARM: mvebu: Fix the operand list in the inline asm of armada_370_xp_pmsu_idle_enter
ARM: mvebu: fix SMP boot for Armada 38x and Armada 375 Z1 in big endian
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A couple of key fixes and a few less critical ones. The main ones
are:
- add a .bss section to the PE/COFF headers when building with EFI
stub
- invoke the correct paravirt magic when building the espfix page
tables
Unfortunately both of these areas also have at least one additional
fix each still in thie pipeline, but which are not yet ready to push"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove unused variable "polling"
x86/espfix/xen: Fix allocation of pages for paravirt page tables
x86/efi: Include a .bss section within the PE/COFF headers
efi: fdt: Do not report an error during boot if UEFI is not available
efi/arm64: efistub: remove local copy of linux_banner
|
|
When CPU topology is specified in device tree, cpu_logical_map() does
not return core ID anymore, but rather full MPIDR value. This breaks
existing calculation of PMU register offsets on Exynos SoCs.
This patch fixes the problem by adjusting the code to use only core ID
bits of the value returned by cpu_logical_map() to allow CPU topology to
be specified in device tree on Exynos SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.16, 2nd take" from Shawn Guo:
The i.MX fixes for 3.16, 2nd take:
It fixes a hard machine hang regression for boards where only pcie is
active but no sata, as the latest imx6-pcie driver is no longer enabling
the upstream clock directly but only lvds clk out.
* tag 'imx-fixes-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: clk-imx6q: parent lvds_sel input from upstream clock gates
Signed-off-by: Olof Johansson <olof@lixom.net>
|
