| Age | Commit message (Collapse) | Author |
|---|
|
https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
* tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants for dra7 mmc voltage and boot issues
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
* tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
ARM: dts: Configure osc clock for d_can on am335x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 5.2:
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
* tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: cpuidle-imx6sx: Restrict the SW2ISO increase to i.MX6SX
firmware: imx: SCU irq should ONLY be enabled after SCU IPC is ready
arm64: imx: Fix build error without CONFIG_SOC_BUS
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"The accumulated fixes from this and last week:
- Fix vmalloc TLB flush and map range calculations which lead to
stale TLBs, spurious faults and other hard to diagnose issues.
- Use fault_in_pages_writable() for prefaulting the user stack in the
FPU code as it's less fragile than the current solution
- Use the PF_KTHREAD flag when checking for a kernel thread instead
of current->mm as the latter can give the wrong answer due to
use_mm()
- Compute the vmemmap size correctly for KASLR and 5-Level paging.
Otherwise this can end up with a way too small vmemmap area.
- Make KASAN and 5-level paging work again by making sure that all
invalid bits are masked out when computing the P4D offset. This
worked before but got broken recently when the LDT remap area was
moved.
- Prevent a NULL pointer dereference in the resource control code
which can be triggered with certain mount options when the
requested resource is not available.
- Enforce ordering of microcode loading vs. perf initialization on
secondary CPUs. Otherwise perf tries to access a non-existing MSR
as the boot CPU marked it as available.
- Don't stop the resource control group walk early otherwise the
control bitmaps are not updated correctly and become inconsistent.
- Unbreak kgdb by returning 0 on success from
kgdb_arch_set_breakpoint() instead of an error code.
- Add more Icelake CPU model defines so depending changes can be
queued in other trees"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
x86/kasan: Fix boot with 5-level paging and KASAN
x86/fpu: Don't use current->mm to check for a kthread
x86/kgdb: Return 0 from kgdb_arch_set_breakpoint()
x86/resctrl: Prevent NULL pointer dereference when local MBM is disabled
x86/resctrl: Don't stop walking closids when a locksetup group is found
x86/fpu: Update kernel's FPU state before using for the fsave header
x86/mm/KASLR: Compute the size of the vmemmap section properly
x86/fpu: Use fault_in_pages_writeable() for pre-faulting
x86/CPU: Add more Icelake model numbers
mm/vmalloc: Avoid rare case of flushing TLB with weird arguments
mm/vmalloc: Fix calculation of direct map addr range
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a regression introduced by our 32-bit KASAN support, which
broke booting on machines with "bootx" early debugging enabled.
A fix for a bug which broke kexec on 32-bit, introduced by changes to
the 32-bit STRICT_KERNEL_RWX support in v5.1.
Finally two fixes going to stable for our THP split/collapse handling,
discovered by Nick. The first fixes random crashes and/or corruption
in guests under sufficient load.
Thanks to: Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu
Malaterre"
* tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32s: fix booting with CONFIG_PPC_EARLY_DEBUG_BOOTX
powerpc/64s: __find_linux_pte() synchronization vs pmdp_invalidate()
powerpc/64s: Fix THP PMD collapse serialisation
powerpc: Fix kexec failure on book3s/32
|
|
Build failure was introduced by the commit identified below,
due to missed macro expension leading to wrong called function's name.
arch/powerpc/kernel/head_fsl_booke.o: In function `SystemCall':
arch/powerpc/kernel/head_fsl_booke.S:416: undefined reference to `kvmppc_handler_BOOKE_INTERRUPT_SYSCALL_SPRN_SRR1'
Makefile:1052: recipe for target 'vmlinux' failed
The called function should be kvmppc_handler_8_0x01B(). This patch fixes it.
Reported-by: Paul Mackerras <paulus@ozlabs.org>
Fixes: 1a4b739bbb4f ("powerpc/32: implement fast entry for syscalls on BOOKE")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Use r10 instead of r9 to calculate CPU offset as r9 contains
the value from SRR1 which is used later.
Fixes: 1a4b739bbb4f ("powerpc/32: implement fast entry for syscalls on BOOKE")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The patch referenced below moved the loading of segment registers
out of load_up_mmu() in order to do it earlier in the boot sequence.
However, the secondary CPU still needs it to be done when loading up
the MMU.
Reported-by: Erhard F. <erhard_f@mailbox.org>
Fixes: 215b823707ce ("powerpc/32s: set up an early static hash table for KASAN")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Adric Blake reported the following warning during suspend-resume:
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0000000000000000) \
at rIP: 0xffffffff8d267924 (native_write_msr+0x4/0x20)
Call Trace:
intel_set_tfa
intel_pmu_cpu_starting
? x86_pmu_dead_cpu
x86_pmu_starting_cpu
cpuhp_invoke_callback
? _raw_spin_lock_irqsave
notify_cpu_starting
start_secondary
secondary_startup_64
microcode: sig=0x806ea, pf=0x80, revision=0x96
microcode: updated to revision 0xb4, date = 2019-04-01
CPU1 is up
The MSR in question is MSR_TFA_RTM_FORCE_ABORT and that MSR is emulated
by microcode. The log above shows that the microcode loader callback
happens after the PMU restoration, leading to the conjecture that
because the microcode hasn't been updated yet, that MSR is not present
yet, leading to the #GP.
Add a microcode loader-specific hotplug vector which comes before
the PERF vectors and thus executes earlier and makes sure the MSR is
present.
Fixes: 400816f60c54 ("perf/x86/intel: Implement support for TSX Force Abort")
Reported-by: Adric Blake <promarbler14@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: x86@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203637
|
|
Since commit 177366bf7ceb the %rbp stopped pointing to %rbp of the
previous stack frame. That broke frame pointer based stack unwinding.
This commit is a partial revert of it.
Note that the location of tail_call_cnt is fixed, since the verifier
enforces MAX_BPF_STACK stack size for programs with tail calls.
Fixes: 177366bf7ceb ("bpf: change x86 JITed program stack layout")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some arm64 fixes for -rc5.
The only non-trivial change (in terms of the diffstat) is fixing our
SVE ptrace API for big-endian machines, but the majority of this is
actually the addition of much-needed comments and updates to the
documentation to try to avoid this mess biting us again in future.
There are still a couple of small things on the horizon, but nothing
major at this point.
Summary:
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Fix missing SVE/FPSIMD endianness conversions
arm64: tlbflush: Ensure start/end of address range are aligned to stride
arm64: Don't unconditionally add -Wno-psabi to KBUILD_CFLAGS
|
|
Since commit d52888aa2753 ("x86/mm: Move LDT remap out of KASLR region on
5-level paging") kernel doesn't boot with KASAN on 5-level paging machines.
The bug is actually in early_p4d_offset() and introduced by commit
12a8cc7fcf54 ("x86/kasan: Use the same shadow offset for 4- and 5-level paging")
early_p4d_offset() tries to convert pgd_val(*pgd) value to a physical
address. This doesn't make sense because pgd_val() already contains the
physical address.
It did work prior to commit d52888aa2753 because the result of
"__pa_nodebug(pgd_val(*pgd)) & PTE_PFN_MASK" was the same as "pgd_val(*pgd)
& PTE_PFN_MASK". __pa_nodebug() just set some high bits which were masked
out by applying PTE_PFN_MASK.
After the change of the PAGE_OFFSET offset in commit d52888aa2753
__pa_nodebug(pgd_val(*pgd)) started to return a value with more high bits
set and PTE_PFN_MASK wasn't enough to mask out all of them. So it returns a
wrong not even canonical address and crashes on the attempt to dereference
it.
Switch back to pgd_val() & PTE_PFN_MASK to cure the issue.
Fixes: 12a8cc7fcf54 ("x86/kasan: Use the same shadow offset for 4- and 5-level paging")
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: kasan-dev@googlegroups.com
Cc: stable@vger.kernel.org
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190614143149.2227-1-aryabinin@virtuozzo.com
|
|
The lcdc device is missing the dma_coherent_mask definition causing the
following warning on da850-evm:
da8xx_lcdc da8xx_lcdc.0: found Sharp_LK043T1DG01 panel
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/dma/mapping.c:247 dma_alloc_attrs+0xc8/0x110
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.0-rc3-00077-g16d72dd4891f #18
Hardware name: DaVinci DA850/OMAP-L138/AM18x EVM
[<c000fce8>] (unwind_backtrace) from [<c000d900>] (show_stack+0x10/0x14)
[<c000d900>] (show_stack) from [<c001a4f8>] (__warn+0xec/0x114)
[<c001a4f8>] (__warn) from [<c001a634>] (warn_slowpath_null+0x3c/0x48)
[<c001a634>] (warn_slowpath_null) from [<c0065860>] (dma_alloc_attrs+0xc8/0x110)
[<c0065860>] (dma_alloc_attrs) from [<c02820f8>] (fb_probe+0x228/0x5a8)
[<c02820f8>] (fb_probe) from [<c02d3e9c>] (platform_drv_probe+0x48/0x9c)
[<c02d3e9c>] (platform_drv_probe) from [<c02d221c>] (really_probe+0x1d8/0x2d4)
[<c02d221c>] (really_probe) from [<c02d2474>] (driver_probe_device+0x5c/0x168)
[<c02d2474>] (driver_probe_device) from [<c02d2728>] (device_driver_attach+0x58/0x60)
[<c02d2728>] (device_driver_attach) from [<c02d27b0>] (__driver_attach+0x80/0xbc)
[<c02d27b0>] (__driver_attach) from [<c02d047c>] (bus_for_each_dev+0x64/0xb4)
[<c02d047c>] (bus_for_each_dev) from [<c02d1590>] (bus_add_driver+0xe4/0x1d8)
[<c02d1590>] (bus_add_driver) from [<c02d301c>] (driver_register+0x78/0x10c)
[<c02d301c>] (driver_register) from [<c000a5c0>] (do_one_initcall+0x48/0x1bc)
[<c000a5c0>] (do_one_initcall) from [<c05cae6c>] (kernel_init_freeable+0x10c/0x1d8)
[<c05cae6c>] (kernel_init_freeable) from [<c048a000>] (kernel_init+0x8/0xf4)
[<c048a000>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Exception stack(0xc6837fb0 to 0xc6837ff8)
7fa0: 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace 8a8073511be81dd2 ]---
Add a 32-bit mask to the platform device's definition.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The BB expander at 0x21 i2c bus 1 fails to probe on da850-evm because
the board doesn't set has_full_constraints to true in the regulator
API.
Call regulator_has_full_constraints() at the end of board registration
just like we do in da850-lcdk and da830-evm.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
BPF_ALU64 div/mod operations are currently using signed division, unlike
BPF_ALU32 operations. Fix the same. DIV64 and MOD64 overflow tests pass
with this fix.
Fixes: 156d0e290e969c ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
current->mm can be non-NULL if a kthread calls use_mm(). Check for
PF_KTHREAD instead to decide when to store user mode FP state.
Fixes: 2722146eb784 ("x86/fpu: Remove fpu->initialized")
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aubrey Li <aubrey.li@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190604175411.GA27477@lst.de
|
|
Unfortunately, a couple of mistakes were made while implementing
Enlightened VMCS support, in particular, wrong clean fields were
used in copy_enlightened_to_vmcs12():
- exception_bitmap is covered by CONTROL_EXCPN;
- vm_exit_controls/pin_based_vm_exec_control/secondary_vm_exec_control
are covered by CONTROL_GRP1.
Fixes: 945679e301ea0 ("KVM: nVMX: add enlightened VMCS state")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The in-memory representation of SVE and FPSIMD registers is
different: the FPSIMD V-registers are stored as single 128-bit
host-endian values, whereas SVE registers are stored in an
endianness-invariant byte order.
This means that the two representations differ when running on a
big-endian host. But we blindly copy data from one representation
to another when converting between the two, resulting in the
register contents being unintentionally byteswapped in certain
situations. Currently this can be triggered by the first SVE
instruction after a syscall, for example (though the potential
trigger points may vary in future).
So, fix the conversion functions fpsimd_to_sve(), sve_to_fpsimd()
and sve_sync_from_fpsimd_zeropad() to swab where appropriate.
There is no common swahl128() or swab128() that we could use here.
Maybe it would be worth making this generic, but for now add a
simple local hack.
Since the byte order differences are exposed in ABI, also clarify
the documentation.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alan Hayward <alan.hayward@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Fixes: bc0ee4760364 ("arm64/sve: Core task context handling")
Fixes: 8cd969d28fd2 ("arm64/sve: Signal handling support")
Fixes: 43d4da2c45b2 ("arm64/sve: ptrace and ELF coredump support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: Fix typos in comments and docs spotted by Julien]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
err must be nonzero in order to reach text_poke(), which caused kgdb to
fail to set breakpoints:
(gdb) break __x64_sys_sync
Breakpoint 1 at 0xffffffff81288910: file ../fs/sync.c, line 124.
(gdb) c
Continuing.
Warning:
Cannot insert breakpoint 1.
Cannot access memory at address 0xffffffff81288910
Command aborted.
Fixes: 86a22057127d ("x86/kgdb: Avoid redundant comparison of patched code")
Signed-off-by: Matt Mullins <mmullins@fb.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nadav Amit <namit@vmware.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190531194755.6320-1-mmullins@fb.com
|
|
Since commit 3d65b6bbc01e ("arm64: tlbi: Set MAX_TLBI_OPS to
PTRS_PER_PTE"), we resort to per-ASID invalidation when attempting to
perform more than PTRS_PER_PTE invalidation instructions in a single
call to __flush_tlb_range(). Whilst this is beneficial, the mmu_gather
code does not ensure that the end address of the range is rounded-up
to the stride when freeing intermediate page tables in pXX_free_tlb(),
which defeats our range checking.
Align the bounds passed into __flush_tlb_range().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Since commit d26c25a9d19b ("arm64: KVM: Tighten guest core register
access from userspace"), KVM_{GET,SET}_ONE_REG rejects register IDs
that do not correspond to a single underlying architectural register.
KVM_GET_REG_LIST was not changed to match however: instead, it
simply yields a list of 32-bit register IDs that together cover the
whole kvm_regs struct. This means that if userspace tries to use
the resulting list of IDs directly to drive calls to KVM_*_ONE_REG,
some of those calls will now fail.
This was not the intention. Instead, iterating KVM_*_ONE_REG over
the list of IDs returned by KVM_GET_REG_LIST should be guaranteed
to work.
This patch fixes the problem by splitting validate_core_offset()
into a backend core_reg_size_from_offset() which does all of the
work except for checking that the size field in the register ID
matches, and kvm_arm_copy_reg_indices() and num_core_regs() are
converted to use this to enumerate the valid offsets.
kvm_arm_copy_reg_indices() now also sets the register ID size field
appropriately based on the value returned, so the register ID
supplied to userspace is fully qualified for use with the register
access ioctls.
Cc: stable@vger.kernel.org
Fixes: d26c25a9d19b ("arm64: KVM: Tighten guest core register access from userspace")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This routine is a one-liner and doesn't really need to be function and
can be implemented as a macro.
Suggested-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This is a GCC only option, which warns about ABI changes within GCC, so
unconditionally adding it breaks Clang with tons of:
warning: unknown warning option '-Wno-psabi' [-Wunknown-warning-option]
and link time failures:
ld.lld: error: undefined symbol: __efistub___stack_chk_guard
>>> referenced by arm-stub.c:73
(/home/nathan/cbl/linux/drivers/firmware/efi/libstub/arm-stub.c:73)
>>> arm-stub.stub.o:(__efistub_install_memreserve_table)
in archive ./drivers/firmware/efi/libstub/lib.a
These failures come from the lack of -fno-stack-protector, which is
added via cc-option in drivers/firmware/efi/libstub/Makefile. When an
unknown flag is added to KBUILD_CFLAGS, clang will noisily warn that it
is ignoring the option like above, unlike gcc, who will just error.
$ echo "int main() { return 0; }" > tmp.c
$ clang -Wno-psabi tmp.c; echo $?
warning: unknown warning option '-Wno-psabi' [-Wunknown-warning-option]
1 warning generated.
0
$ gcc -Wsometimes-uninitialized tmp.c; echo $?
gcc: error: unrecognized command line option
‘-Wsometimes-uninitialized’; did you mean ‘-Wmaybe-uninitialized’?
1
For cc-option to work properly with clang and behave like gcc, -Werror
is needed, which was done in commit c3f0d0bc5b01 ("kbuild, LLVMLinux:
Add -Werror to cc-option to support clang").
$ clang -Werror -Wno-psabi tmp.c; echo $?
error: unknown warning option '-Wno-psabi'
[-Werror,-Wunknown-warning-option]
1
As a consequence of this, when an unknown flag is unconditionally added
to KBUILD_CFLAGS, it will cause cc-option to always fail and those flags
will never get added:
$ clang -Werror -Wno-psabi -fno-stack-protector tmp.c; echo $?
error: unknown warning option '-Wno-psabi'
[-Werror,-Wunknown-warning-option]
1
This can be seen when compiling the whole kernel as some warnings that
are normally disabled (see below) show up. The full list of flags
missing from drivers/firmware/efi/libstub are the following (gathered
from diffing .arm64-stub.o.cmd):
-fno-delete-null-pointer-checks
-Wno-address-of-packed-member
-Wframe-larger-than=2048
-Wno-unused-const-variable
-fno-strict-overflow
-fno-merge-all-constants
-fno-stack-check
-Werror=date-time
-Werror=incompatible-pointer-types
-ffreestanding
-fno-stack-protector
Use cc-disable-warning so that it gets disabled for GCC and does nothing
for Clang.
Fixes: ebcc5928c5d9 ("arm64: Silence gcc warnings about arch ABI drift")
Link: https://github.com/ClangBuiltLinux/linux/issues/511
Reported-by: Qian Cai <cai@lca.pw>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Compared to kernel 5.0, patches merged for 5.1 added support for A38x'
PHY guarded by a config option which was not enabled by default. As a
result, there was no eth1 and eth2 on a Solid Run Clearfog Base.
Ensure that A38x PHY is enabled on mvebu.
[gregory: issue appeared in 5.1 not in 5.2 and added Fixes tag]
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: a10c1c8191e0 ("net: marvell: neta: add comphy support")
Cc: stable@kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Booting with kernel parameter "rdt=cmt,mbmtotal,memlocal,l3cat,mba" and
executing "mount -t resctrl resctrl -o mba_MBps /sys/fs/resctrl" results in
a NULL pointer dereference on systems which do not have local MBM support
enabled..
BUG: kernel NULL pointer dereference, address: 0000000000000020
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 0 PID: 722 Comm: kworker/0:3 Not tainted 5.2.0-0.rc3.git0.1.el7_UNSUPPORTED.x86_64 #2
Workqueue: events mbm_handle_overflow
RIP: 0010:mbm_handle_overflow+0x150/0x2b0
Only enter the bandwith update loop if the system has local MBM enabled.
Fixes: de73f38f7680 ("x86/intel_rdt/mba_sc: Feedback loop to dynamically update mem bandwidth")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190610171544.13474-1-prarit@redhat.com
|
|
When a new control group is created __init_one_rdt_domain() walks all
the other closids to calculate the sets of used and unused bits.
If it discovers a pseudo_locksetup group, it breaks out of the loop. This
means any later closid doesn't get its used bits added to used_b. These
bits will then get set in unused_b, and added to the new control group's
configuration, even if they were marked as exclusive for a later closid.
When encountering a pseudo_locksetup group, we should continue. This is
because "a resource group enters 'pseudo-locked' mode after the schemata is
written while the resource group is in 'pseudo-locksetup' mode." When we
find a pseudo_locksetup group, its configuration is expected to be
overwritten, we can skip it.
Fixes: dfe9674b04ff6 ("x86/intel_rdt: Enable entering of pseudo-locksetup mode")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H Peter Avin <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190603172531.178830-1-james.morse@arm.com
|
|
In RV32, udelay would delay the wrong cycle. When it shifts right
"UDELAY_SHIFT" bits, it either delays 0 cycle or 1 cycle. It only works
correctly in RV64. Because the 'ucycles' always needs to be 64 bits
variable.
Signed-off-by: Nick Hu <nickhu@andestech.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: fixed minor spelling error]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Commit bf0102a0fdd9 ("riscv: call pm_power_off from machine_halt /
machine_power_off") removed the export of pm_power_off, but it is used by
several modules:
ERROR: "pm_power_off" [drivers/mfd/rk808.ko] undefined!
ERROR: "pm_power_off" [drivers/mfd/max8907.ko] undefined!
ERROR: "pm_power_off" [drivers/mfd/axp20x.ko] undefined!
ERROR: "pm_power_off" [drivers/char/ipmi/ipmi_poweroff.ko] undefined!
Signed-off-by: Andreas Schwab <schwab@suse.de>
Fixes: bf0102a0fdd9 ("riscv: call pm_power_off from machine_halt / machine_power_off")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Enable PRCI clock driver and serial console by default, so the default
upstream defconfig is bootable to a serial console.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
s390:tinyconfig fails to build with gcc 8.3.0.
arch/s390/include/asm/ctl_reg.h:52:2: error: impossible constraint in 'asm'
asm volatile( \
^~~
arch/s390/include/asm/ctl_reg.h:62:2: note: in expansion of macro '__ctl_store'
__ctl_store(reg, cr, cr);
^~~~~~~~~~~
s390/include/asm/ctl_reg.h:41:2: error: impossible constraint in 'asm'
asm volatile( \
^~~
arch/s390/include/asm/ctl_reg.h:64:2:
note: in expansion of macro '__ctl_load'
__ctl_load(reg, cr, cr);
^~~~~~~~~~
Marking __ctl_set_bit and __ctl_clear_bit as __always_inline fixes the
problem.
Fixes: 9012d011660e ("compiler: allow all arches to enable CONFIG_OPTIMIZE_INLINING")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Get rid of gcc9 warnings like this:
arch/s390/boot/ipl_report.c: In function 'find_bootdata_space':
arch/s390/boot/ipl_report.c:42:26: warning: taking address of packed member of 'struct ipl_rb_components' may result in an unaligned pointer value [-Waddress-of-packed-member]
42 | for_each_rb_entry(comp, comps)
| ^~~~~
This is effectively the s390 variant of commit 20c6c1890455
("x86/boot: Disable the address-of-packed-member compiler warning").
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
usb4_tm is unsed on dra72 and accessing the module
with ti,sysc is causing a boot crash hence disable its target
module.
Fixes: 549fce068a3112 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data")
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- fix stack unwinder: the stack unwinder rework has on off-by-one bug
which prevents following stack backchains over more than one context
(e.g. irq -> process).
- fix address space detection in exception handler: if user space
switches to access register mode, which is not supported anymore, the
exception handler may resolve to the wrong address space.
* tag 's390-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/unwind: correct stack switching during unwind
s390/mm: fix address space detection in exception handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
- Declare ginvt() __always_inline due to its use of an argument as an
inline asm immediate.
- A VDSO build fix following Kbuild changes made this cycle.
- A fix for boot failures on txx9 systems following memory
initialization changes made this cycle.
- Bounds check virt_addr_valid() to prevent it spuriously indicating
that bogus addresses are valid, in turn fixing hardened usercopy
failures that have been present since v4.12.
- Build uImage.gz for pistachio systems by default, since this is the
image we need in order to actually boot on a board.
- Remove an unused variable in our uprobes code.
* tag 'mips_fixes_5.2_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: uprobes: remove set but not used variable 'epc'
MIPS: pistachio: Build uImage.gz by default
MIPS: Make virt_addr_valid() return bool
MIPS: Bounds check virt_addr_valid
MIPS: TXx9: Fix boot crash in free_initmem()
MIPS: remove a space after -I to cope with header search paths for VDSO
MIPS: mark ginvt() as __always_inline
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
|
|
In commit
39388e80f9b0c ("x86/fpu: Don't save fxregs for ia32 frames in copy_fpstate_to_sigframe()")
I removed the statement
| if (ia32_fxstate)
| copy_fxregs_to_kernel(fpu);
and argued that it was wrongly merged because the content was already
saved in kernel's state.
This was wrong: It is required to write it back because it is only
saved on the user-stack and save_fsave_header() reads it from task's
FPU-state. I missed that part…
Save x87 FPU state unless thread's FPU registers are already up to date.
Fixes: 39388e80f9b0c ("x86/fpu: Don't save fxregs for ia32 frames in copy_fpstate_to_sigframe()")
Reported-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190607142915.y52mfmgk5lvhll7n@linutronix.de
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2019-06-07
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix several bugs in riscv64 JIT code emission which forgot to clear high
32-bits for alu32 ops, from Björn and Luke with selftests covering all
relevant BPF alu ops from Björn and Jiong.
2) Two fixes for UDP BPF reuseport that avoid calling the program in case of
__udp6_lib_err and UDP GRO which broke reuseport_select_sock() assumption
that skb->data is pointing to transport header, from Martin.
3) Two fixes for BPF sockmap: a use-after-free from sleep in psock's backlog
workqueue, and a missing restore of sk_write_space when psock gets dropped,
from Jakub and John.
4) Fix unconnected UDP sendmsg hook API which is insufficient as-is since it
breaks standard applications like DNS if reverse NAT is not performed upon
receive, from Daniel.
5) Fix an out-of-bounds read in __bpf_skc_lookup which in case of AF_INET6
fails to verify that the length of the tuple is long enough, from Lorenz.
6) Fix libbpf's libbpf__probe_raw_btf to return an fd instead of 0/1 (for
{un,}successful probe) as that is expected to be propagated as an fd to
load_sk_storage_btf() and thus closing the wrong descriptor otherwise,
from Michal.
7) Fix bpftool's JSON output for the case when a lookup fails, from Krzesimir.
8) Minor misc fixes in docs, samples and selftests, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of the vmemmap section is hardcoded to 1 TB to support the
maximum amount of system RAM in 4-level paging mode - 64 TB.
However, 1 TB is not enough for vmemmap in 5-level paging mode. Assuming
the size of struct page is 64 Bytes, to support 4 PB system RAM in 5-level,
64 TB of vmemmap area is needed:
4 * 1000^5 PB / 4096 bytes page size * 64 bytes per page struct / 1000^4 TB = 62.5 TB.
This hardcoding may cause vmemmap to corrupt the following
cpu_entry_area section, if KASLR puts vmemmap very close to it and the
actual vmemmap size is bigger than 1 TB.
So calculate the actual size of the vmemmap region needed and then align
it up to 1 TB boundary.
In 4-level paging mode it is always 1 TB. In 5-level it's adjusted on
demand. The current code reserves 0.5 PB for vmemmap on 5-level. With
this change, the space can be saved and thus used to increase entropy
for the randomization.
[ bp: Spell out how the 64 TB needed for vmemmap is computed and massage commit
message. ]
Fixes: eedb92abb9bb ("x86/mm: Make virtual memory layout dynamic for CONFIG_X86_5LEVEL=y")
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Kirill A. Shutemov <kirill@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: kirill.shutemov@linux.intel.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable <stable@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190523025744.3756-1-bhe@redhat.com
|
|
Pull xtensa fix from Max Filippov:
"Fix a section mismatch between memblock_reserve and mem_reserve.
This fixes tinyconfig xtensa builds"
* tag 'xtensa-20190607' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: Fix section mismatch between memblock_reserve and mem_reserve
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a crash during resume from hibernation introduced during the
4.19 cycle, cause the new Performance and Energy Bias Hint (EPB) code
to be built only if CONFIG_PM is set and add a few missing kerneldoc
comments.
Specifics:
- Fix a crash that occurs when a kernel with 'nosmt' in the command
line is used to resume the system from hibernation (as the
"restore" kernel), because memory mapping differences between the
restore and image kernels cause SMT siblings to be woken up from
idle states and subsequently they try to fetch instructions from
incorrect memory locations (Jiri Kosina).
- Cause the new Performance and Energy Bias Hint (EPB) code to be
built only if CONFIG_PM is set, because that code is not really
necessary otherwise (Rafael Wysocki).
- Add kerneldoc comments to documents some helper functions related
to system-wide suspend to avoid possible confusion regarding their
purpose (Rafael Wysocki)"
* tag 'pm-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power: Fix 'nosmt' vs hibernation triple fault during resume
PM: sleep: Add kerneldoc comments to some functions
x86: intel_epb: Do not build when CONFIG_PM is unset
|
|
get_desc() computes a pointer into the LDT while holding a lock that
protects the LDT from being freed, but then drops the lock and returns the
(now potentially dangling) pointer to its caller.
Fix it by giving the caller a copy of the LDT entry instead.
Fixes: 670f928ba09b ("x86/insn-eval: Add utility function to get segment descriptor")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Another round of mostly-benign fixes, the exception being a boot crash
on SVE2-capable CPUs (although I don't know where you'd find such a
thing, so maybe it's benign too).
We're in the process of resolving some big-endian ptrace breakage, so
I'll probably have some more for you next week.
Summary:
- Fix boot crash on platforms with SVE2 due to missing register
encoding
- Fix architected timer accessors when CONFIG_OPTIMIZE_INLINING=y
- Move cpu_logical_map into smp.h for use by upcoming irqchip drivers
- Trivial typo fix in comment
- Disable some useless, noisy warnings from GCC 9"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence gcc warnings about arch ABI drift
ARM64: trivial: s/TIF_SECOMP/TIF_SECCOMP/ comment typo fix
arm64: arch_timer: mark functions as __always_inline
arm64: smp: Moved cpu_logical_map[] to smp.h
arm64: cpufeature: Fix missing ZFR0 in __read_sysreg_by_encoding()
|
|
Adjust conditions in on_stack function. That fixes backchain unwinder
which was unable to read pt_regs at the very bottom of the stack and
hence couldn't follow stacks (e.g. from async stack to a task stack).
Fixes: 78c98f907413 ("s390/unwind: introduce stack unwind API")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
When booting through OF, setup_disp_bat() does nothing because
disp_BAT are not set. By change, it used to work because BOOTX
buffer is mapped 1:1 at address 0x81000000 by the bootloader, and
btext_setup_display() sets virt addr same as phys addr.
But since commit 215b823707ce ("powerpc/32s: set up an early static
hash table for KASAN."), a temporary page table overrides the
bootloader mapping.
This 0x81000000 is also problematic with the newly implemented
Kernel Userspace Access Protection (KUAP) because it is within user
address space.
This patch fixes those issues by properly setting disp_BAT through
a call to btext_prepare_BAT(), allowing setup_disp_bat() to
properly setup BAT3 for early bootx screen buffer access.
Reported-by: Mathieu Malaterre <malat@debian.org>
Fixes: 215b823707ce ("powerpc/32s: set up an early static hash table for KASAN.")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
* pm-x86:
x86/power: Fix 'nosmt' vs hibernation triple fault during resume
x86: intel_epb: Do not build when CONFIG_PM is unset
|
|
The change to pmdp_invalidate() to mark the pmd with _PAGE_INVALID
broke the synchronisation against lock free lookups,
__find_linux_pte()'s pmd_none() check no longer returns true for such
cases.
Fix this by adding a check for this condition as well.
Fixes: da7ad366b497 ("powerpc/mm/book3s: Update pmd_present to look at _PAGE_PRESENT bit")
Cc: stable@vger.kernel.org # v4.20+
Suggested-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 1b2443a547f9 ("powerpc/book3s64: Avoid multiple endian
conversion in pte helpers") changed the actual bitwise tests in
pte_access_permitted by using pte_write() and pte_present() helpers
rather than raw bitwise testing _PAGE_WRITE and _PAGE_PRESENT bits.
The pte_present() change now returns true for PTEs which are
!_PAGE_PRESENT and _PAGE_INVALID, which is the combination used by
pmdp_invalidate() to synchronize access from lock-free lookups.
pte_access_permitted() is used by pmd_access_permitted(), so allowing
GUP lock free access to proceed with such PTEs breaks this
synchronisation.
This bug has been observed on a host using the hash page table MMU,
with random crashes and corruption in guests, usually together with
bad PMD messages in the host.
Fix this by adding an explicit check in pmd_access_permitted(), and
documenting the condition explicitly.
The pte_write() change should be okay, and would prevent GUP from
falling back to the slow path when encountering savedwrite PTEs, which
matches what x86 (that does not implement savedwrite) does.
Fixes: 1b2443a547f9 ("powerpc/book3s64: Avoid multiple endian conversion in pte helpers")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In the old days, _PAGE_EXEC didn't exist on 6xx aka book3s/32.
Therefore, allthough __mapin_ram_chunk() was already mapping kernel
text with PAGE_KERNEL_TEXT and the rest with PAGE_KERNEL, the entire
memory was executable. Part of the memory (first 512kbytes) was
mapped with BATs instead of page table, but it was also entirely
mapped as executable.
In commit 385e89d5b20f ("powerpc/mm: add exec protection on
powerpc 603"), we started adding exec protection to some 6xx, namely
the 603, for pages mapped via pagetables.
Then, in commit 63b2bc619565 ("powerpc/mm/32s: Use BATs for
STRICT_KERNEL_RWX"), the exec protection was extended to BAT mapped
memory, so that really only the kernel text could be executed.
The problem here is that kexec is based on copying some code into
upper part of memory then executing it from there in order to install
a fresh new kernel at its definitive location.
However, the code is position independant and first part of it is
just there to deactivate the MMU and jump to the second part. So it
is possible to run this first part inplace instead of running the
copy. Once the MMU is off, there is no protection anymore and the
second part of the code will just run as before.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 63b2bc619565 ("powerpc/mm/32s: Use BATs for STRICT_KERNEL_RWX")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Fix crashes when accessing PCI devices on some machines like C240 and
J5000. The crashes were triggered because we replaced cache flushes
by nops in the alternative coding where we shouldn't for some
machines.
- Dave fixed a race in the usage of the sr1 space register when used to
load the coherence index.
- Use the hardware lpa instruction to to load the physical address of
kernel virtual addresses in the iommu driver code.
- The kernel may fail to link when CONFIG_MLONGCALLS isn't set. Solve
that by rearranging functions in the final vmlinux executeable.
- Some defconfig cleanups and removal of compiler warnings.
* 'parisc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix crash due alternative coding for NP iopdir_fdc bit
parisc: Use lpa instruction to load physical addresses in driver code
parisc: configs: Remove useless UEVENT_HELPER_PATH
parisc: Use implicit space register selection for loading the coherence index of I/O pdirs
parisc: Fix compiler warnings in float emulation code
parisc/slab: cleanup after /proc/slab_allocators removal
parisc: Allow building 64-bit kernel without -mlong-calls compiler option
parisc: Kconfig: remove ARCH_DISCARD_MEMBLOCK
|
