| Age | Commit message (Collapse) | Author |
|---|
|
Often all is needed is these small helpers, instead of compiler.h or a
full kprobes.h. This is important for asm helpers, in fact even some
asm/kprobes.h make use of these helpers... instead just keep a generic
asm file with helpers useful for asm code with the least amount of
clutter as possible.
Likewise we need now to also address what to do about this file for both
when architectures have CONFIG_HAVE_KPROBES, and when they do not. Then
for when architectures have CONFIG_HAVE_KPROBES but have disabled
CONFIG_KPROBES.
Right now most asm/kprobes.h do not have guards against CONFIG_KPROBES,
this means most architecture code cannot include asm/kprobes.h safely.
Correct this and add guards for architectures missing them.
Additionally provide architectures that not have kprobes support with
the default asm-generic solution. This lets us force asm/kprobes.h on
the header include/linux/kprobes.h always, but most importantly we can
now safely include just asm/kprobes.h on architecture code without
bringing the full kitchen sink of header files.
Two architectures already provided a guard against CONFIG_KPROBES on its
kprobes.h: sh, arch. The rest of the architectures needed gaurds added.
We avoid including any not-needed headers on asm/kprobes.h unless
kprobes have been enabled.
In a subsequent atomic change we can try now to remove compiler.h from
include/linux/kprobes.h.
During this sweep I've also identified a few architectures defining a
common macro needed for both kprobes and ftrace, that of the definition
of the breakput instruction up. Some refer to this as
BREAKPOINT_INSTRUCTION. This must be kept outside of the #ifdef
CONFIG_KPROBES guard.
[mcgrof@kernel.org: fix arm64 build]
Link: http://lkml.kernel.org/r/CAB=NE6X1WMByuARS4mZ1g9+W=LuVBnMDnh_5zyN0CLADaVh=Jw@mail.gmail.com
[sfr@canb.auug.org.au: fixup for kprobes declarations moving]
Link: http://lkml.kernel.org/r/20170214165933.13ebd4f4@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170203233139.32682-1-mcgrof@kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Big picture:
- New intel_turbo_max_3 driver, providing max core frequency
information to the scheduler. Intel PMC APL support, s0ix read API,
and fixes.
- New Silead touchscreen platform touchscreen descriptions.
Additional hotkey support for the intel-hid driver.
- New model support for dell-laptop and hp_accel.
- Several cleanups, especially to the fujitsu-laptop and
intel_mid_powerbtn drivers.
Detail summary:
platorm/x86:
- silead depends on I2C being built-in
- add support for devices with Silead touchscreens
- Support Turbo Boost Max 3.0 for non HWP systems
intel_turbo_max_3:
- make it explicitly non-modular
dell-laptop:
- Add Latitude 7480 and others to the DMI whitelist
intel-hid:
- Support 5 button array
thinkpad_acpi:
- Call led_classdev_notify_brightness_hw_changed on kbd brightness change
- Use brightness_set_blocking callback for LEDs
- Stop setting led_classdev brightness directly
acer-wmi:
- add another KEY_WLAN keycode
- Inform firmware that RF Button Driver is active
- setup accelerometer when machine has appropriate notify event
asus-wireless:
- Fix indentation
- Use per-HID HSWC parameters
intel_pmc_ipc:
- Add APL PMC PCI Id
- read s0ix residency API
- Remove unused iTCO_version variable
alienware-wmi:
- Remove header duplicate
intel_pmc_core:
- fix out-of-bounds accesses on stack
intel_mid_powerbtn:
- Use SCU IPC directly
- Unify IRQ acknowledgment
- Move comment to where it belongs
- Unify PBSTATUS access
- Remove snail address
- Sort headers alphabetically
- Join string literals
- Enable driver for Merrifield
- Acknowledge interrupts
- Factor out mfld_ack()
- Introduce driver data
- Substitute mfld by mid
- Convert to use devm_*()
fujitsu-laptop:
- make hotkey handling functions more similar
- break up complex loop condition
- move keycode processing to separate functions
- decrease indentation in acpi_fujitsu_hotkey_notify()
- simplify logolamp_get()
- rework logolamp_set() to properly handle errors
- set default trigger for radio LED to rfkill-any
dell-smbios:
- Auto-select as needed
intel_mid_thermal:
- Fix module autoload
- Remove duplicated platform device ID
mlx-platform:
- mlxcpld-hotplug driver style fixes
hp_accel:
- Add support for HP ZBook 17"
* tag 'platform-drivers-x86-v4.11-1' of git://git.infradead.org/linux-platform-drivers-x86: (45 commits)
platform/x86: intel_turbo_max_3: make it explicitly non-modular
platform/x86: dell-laptop: Add Latitude 7480 and others to the DMI whitelist
platform/x86: intel-hid: Support 5 button array
platform/x86: thinkpad_acpi: Call led_classdev_notify_brightness_hw_changed on kbd brightness change
platform/x86: thinkpad_acpi: Use brightness_set_blocking callback for LEDs
platform/x86: thinkpad_acpi: Stop setting led_classdev brightness directly
leds: class: Add new optional brightness_hw_changed attribute
platform/x86: acer-wmi: add another KEY_WLAN keycode
platform/x86: acer-wmi: Inform firmware that RF Button Driver is active
platform/x86: asus-wireless: Fix indentation
platform/x86: asus-wireless: Use per-HID HSWC parameters
platform/x86: intel_pmc_ipc: Add APL PMC PCI Id
platform/x86: intel_pmc_ipc: read s0ix residency API
platform/x86: alienware-wmi: Remove header duplicate
platform/x86: intel_mid_powerbtn: Use SCU IPC directly
platform/x86: intel_mid_powerbtn: Unify IRQ acknowledgment
platform/x86: intel_mid_powerbtn: Move comment to where it belongs
platform/x86: intel_mid_powerbtn: Unify PBSTATUS access
platform/x86: intel_pmc_core: fix out-of-bounds accesses on stack
platform/x86: silead depends on I2C being built-in
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of new drivers, non-critical fixes, and updates
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
clk: renesas: mstp: ensure register writes complete
clk: qcom: Do not drop device node twice
clk: mvebu: adjust clock handling for the CP110 system controller
clk: mvebu: Expand mv98dx3236-core-clock support
clk: zte: add i2s clocks for zx296718
clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
clk: tegra: Add BPMP clock driver
clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
clk: uniphier: add NAND clock for all UniPhier SoCs
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: qcom: SDHCI enablement on Nexus 5X / 6P
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
|
|
These are the current source files that should not have
executable attributes set.
[ Normally this would be sent through Andrew Morton's tree
but his quilt tools don't like permission only patches. ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge more updates from Andrew Morton:
- almost all of the rest of MM
- misc bits
- KASAN updates
- procfs
- lib/ updates
- checkpatch updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (124 commits)
checkpatch: remove false unbalanced braces warning
checkpatch: notice unbalanced else braces in a patch
checkpatch: add another old address for the FSF
checkpatch: update $logFunctions
checkpatch: warn on logging continuations
checkpatch: warn on embedded function names
lib/lz4: remove back-compat wrappers
fs/pstore: fs/squashfs: change usage of LZ4 to work with new LZ4 version
crypto: change LZ4 modules to work with new LZ4 module version
lib/decompress_unlz4: change module to work with new LZ4 module version
lib: update LZ4 compressor module
lib/test_sort.c: make it explicitly non-modular
lib: add CONFIG_TEST_SORT to enable self-test of sort()
rbtree: use designated initializers
linux/kernel.h: fix DIV_ROUND_CLOSEST to support negative divisors
lib/find_bit.c: micro-optimise find_next_*_bit
lib: add module support to atomic64 tests
lib: add module support to glob tests
lib: add module support to crc32 tests
kernel/ksysfs.c: add __ro_after_init to bin_attribute structure
...
|
|
This patch adds a new API to indicate S0ix residency in usec. It utilizes
the PMC Global Control Registers (GCR) to read deep and shallow
S0ix residency.
PMC MMIO resources:
o Lower 4kB: IPC1 (PMC inter-processor communication) interface
o Upper 4kB: GCR (Global Control Registers)
This enables the power management framework to take corrective actions when
the platform fails to enter S0ix after kernel freeze as part of the suspend
to idle flow. (echo freeze > /sys/power/state).
This is expected to be used with a S0ix failsafe framework such as:
<https://lwn.net/Articles/689505/>
[rajneesh: folded in "fix division in 32-bit case" from Andy Shevchenko]
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
[andy: fixed kbuild error, removed "total" from variables, fixed macro]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Pull OpenRISC updates from Stafford Horne:
"Highlights include:
- optimized memset and memcpy routines, ~20% boot time saving
- support for cpu idling
- adding support for l.swa and l.lwa atomic operations (in spec from
2014)
- use atomics to implement: bitops, cmpxchg, futex
- the atomics are in preparation for SMP support"
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux: (25 commits)
openrisc: head: Init r0 to 0 on start
openrisc: Export ioremap symbols used by modules
arch/openrisc/lib/memcpy.c: use correct OR1200 option
openrisc: head: Remove unused strings
openrisc: head: Move init strings to rodata section
openrisc: entry: Fix delay slot detection
openrisc: entry: Whitespace and comment cleanups
scripts/checkstack.pl: Add openrisc support
MAINTAINERS: Add the openrisc official repository
openrisc: Add .gitignore
openrisc: Add optimized memcpy routine
openrisc: Add optimized memset
openrisc: Initial support for the idle state
openrisc: Fix the bitmask for the unit present register
openrisc: remove unnecessary stddef.h include
openrisc: add futex_atomic_* implementations
openrisc: add optimized atomic operations
openrisc: add cmpxchg and xchg implementations
openrisc: add atomic bitops
openrisc: add l.lwa/l.swa emulation
...
|
|
There is <linux/compiler.h> which provides macros for various gcc
specific constructs. Eg: __weak for __attribute__((weak)). I've
cleaned all instances of gcc specific attributes with the right macros
for all files under /arch/m68k
Link: http://lkml.kernel.org/r/1485540901-1988-3-git-send-email-gidisrael@gmail.com
Signed-off-by: Gideon Israel Dsouza <gidisrael@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Given that the arch does not add its own implementations, simply use the
asm-generic/current.h (generic-y) header instead of duplicating code.
Link: http://lkml.kernel.org/r/1485992878-4780-2-git-send-email-dave@stgolabs.net
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The build of frv defconfig gives warning:
arch/frv/mb93090-mb00/pci-frv.c:176:5: warning: ignoring return value of 'pci_assign_resource', declared with attribute warn_unused_result
Just print an error message to silence the warning. We can not do much
here on error.
Link: http://lkml.kernel.org/r/1484256471-5379-1-git-send-email-sudipm.mukherjee@gmail.com
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove the prototypes for shmem_mapping() and shmem_zero_setup() from
linux/mm.h, since they are already provided in linux/shmem_fs.h. But
shmem_fs.h must then provide the inline stub for shmem_mapping() when
CONFIG_SHMEM is not set, and a few more cfiles now need to #include it.
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1702081658250.1549@eggly.anvils
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this our protnone becomes a present pte with READ/WRITE/EXEC bit
cleared. By default we also set _PAGE_PRIVILEGED on such pte. This is
now used to help us identify a protnone pte that as saved write bit.
For such pte, we will clear the _PAGE_PRIVILEGED bit. The pte still
remain non-accessible from both user and kernel.
[aneesh.kumar@linux.vnet.ibm.com: v3]
Link: http://lkml.kernel.org/r/1487498625-10891-4-git-send-email-aneesh.kumar@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1487050314-3892-3-git-send-email-aneesh.kumar@linux.vnet.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The callers of the DMA alloc functions already provide the proper
context GFP flags. Make sure to pass them through to the CMA allocator,
to make the CMA compaction context aware.
Link: http://lkml.kernel.org/r/20170127172328.18574-3-l.stach@pengutronix.de
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Most users of this interface just want to use it with the default
GFP_KERNEL flags, but for cases where DMA memory is allocated it may be
called from a different context.
No functional change yet, just passing through the flag to the
underlying alloc_contig_range function.
Link: http://lkml.kernel.org/r/20170127172328.18574-2-l.stach@pengutronix.de
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When a non-cooperative userfaultfd monitor copies pages in the
background, it may encounter regions that were already unmapped.
Addition of UFFD_EVENT_UNMAP allows the uffd monitor to track precisely
changes in the virtual memory layout.
Since there might be different uffd contexts for the affected VMAs, we
first should create a temporary representation for the unmap event for
each uffd context and then notify them one by one to the appropriate
userfault file descriptors.
The event notification occurs after the mmap_sem has been released.
[arnd@arndb.de: fix nommu build]
Link: http://lkml.kernel.org/r/20170203165141.3665284-1-arnd@arndb.de
[mhocko@suse.com: fix nommu build]
Link: http://lkml.kernel.org/r/20170202091503.GA22823@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/1485542673-24387-3-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A new unit test for the device-dax 1GB enabling currently fails with
this warning before hanging the test thread:
WARNING: CPU: 0 PID: 21 at lib/percpu-refcount.c:155 percpu_ref_switch_to_atomic_rcu+0x1e3/0x1f0
percpu ref (dax_pmem_percpu_release [dax_pmem]) <= 0 (0) after switching to atomic
[..]
CPU: 0 PID: 21 Comm: rcuos/1 Tainted: G O 4.10.0-rc7-next-20170207+ #944
[..]
Call Trace:
dump_stack+0x86/0xc3
__warn+0xcb/0xf0
warn_slowpath_fmt+0x5f/0x80
? rcu_nocb_kthread+0x27a/0x510
? dax_pmem_percpu_exit+0x50/0x50 [dax_pmem]
percpu_ref_switch_to_atomic_rcu+0x1e3/0x1f0
? percpu_ref_exit+0x60/0x60
rcu_nocb_kthread+0x339/0x510
? rcu_nocb_kthread+0x27a/0x510
kthread+0x101/0x140
The get_user_pages() path needs to arrange for references to be taken
against the dev_pagemap instance backing the pud mapping. Refactor the
existing __gup_device_huge_pmd() to also account for the pud case.
Link: http://lkml.kernel.org/r/148653181153.38226.9605457830505509385.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current transparent hugepage code only supports PMDs. This patch
adds support for transparent use of PUDs with DAX. It does not include
support for anonymous pages. x86 support code also added.
Most of this patch simply parallels the work that was done for huge
PMDs. The only major difference is how the new ->pud_entry method in
mm_walk works. The ->pmd_entry method replaces the ->pte_entry method,
whereas the ->pud_entry method works along with either ->pmd_entry or
->pte_entry. The pagewalk code takes care of locking the PUD before
calling ->pud_walk, so handlers do not need to worry whether the PUD is
stable.
[dave.jiang@intel.com: fix SMP x86 32bit build for native_pud_clear()]
Link: http://lkml.kernel.org/r/148719066814.31111.3239231168815337012.stgit@djiang5-desk3.ch.intel.com
[dave.jiang@intel.com: native_pud_clear missing on i386 build]
Link: http://lkml.kernel.org/r/148640375195.69754.3315433724330910314.stgit@djiang5-desk3.ch.intel.com
Link: http://lkml.kernel.org/r/148545059381.17912.8602162635537598445.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Provide the name of each memblock type with struct memblock_type. This
allows to get rid of the function memblock_type_name() and duplicating
the type names in __memblock_dump_all().
The only memblock_type usage out of mm/memblock.c seems to be
arch/s390/kernel/crash_dump.c. While at it, give it a name.
Link: http://lkml.kernel.org/r/20170120123456.46508-4-heiko.carstens@de.ibm.com
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Given that the arch does not add its own implementations, simply use the
asm-generic/current.h (generic-y) header instead of duplicating code.
Link: http://lkml.kernel.org/r/1485992878-4780-3-git-send-email-dave@stgolabs.net
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull sparc updates from David Miller:
1) Support multiple huge page sizes, from Nitin Gupta.
2) Improve boot time on large memory configurations, from Pavel
Tatashin.
3) Make BRK handling more consistent and documented, from Vijay Kumar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build error in flush_tsb_user_page
sparc64: memblock resizes are not handled properly
sparc64: use latency groups to improve add_node_ranges speed
sparc64: Add 64K page size support
sparc64: Multi-page size support
Documentation/sparc: Steps for sending break on sunhv console
sparc64: Send break twice from console to return to boot prom
sparc64: Migrate hvcons irq to panicked cpu
sparc64: Set cpu state to offline when stopped
sunvdc: Add support for setting physical sector size
sparc64: fix for user probes in high memory
sparc: topology_64.h: Fix condition for including cpudata.h
sparc32: mm: srmmu: add __ro_after_init to sparc32_cachetlb_ops structures
|
|
Originally openrisc spec 0 specified that r0 would be wired to ground.
This is no longer the case. r0 is not guaranteed to be 0 at init, so we
need to initialize it to 0 before using it.
Also, if we are clearing r0 we cant use r0 to clear itself. Change the
the CLEAR_GPR macro to use movhi for clearing.
Reported-by: Jakob Viketoft <jakob.viketoft@aacmicrotec.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Noticed this when building with allyesconfig. Got build failures due
to iounmap and __ioremap symbols missing. This patch exports them so
modules can use them. This is inline with other architectures.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The Kconfig option for OR12000 is OR1K_1200.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
These string definitions are no longer used removed them. Noticed this
while working on a CONFIG_DEBUG_INFO build issue.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The strings used during the head/init phase of openrisc bootup were
stored in the executable section of the binary.
This causes compilation to fail when using CONFIG_DEBUG_INFO with
error:
Error: unaligned opcodes detected in executable segment
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Use execption SR stored in pt_regs for detection, the current SR is not
correct as the handler is running after return from exception.
Also, The code that checks for a delay slot uses a flag bitmask and then
wants to check if the result is not zero. The test it implemented was
wrong.
Correct it by changing the test to check result against non zero.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Cleanups to whitespace and add some comments. Reading through the delay
slot logic I noticed some things:
- Delay slot instructions were not indented
- Some comments are not lined up
- Use tabs and spaces consistent with other code
No functional change
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This helps to suppress the vmlinux.lds file.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The generic memcpy routine provided in kernel does only byte copies.
Using word copies we can lower boot time and cycles spend in memcpy
quite significantly.
Booting on my de0 nano I see boot times go from 7.2 to 5.6 seconds.
The avg cycles in memcpy during boot go from 6467 to 1887.
I tested several algorithms (see code in previous patch mails)
The implementations I tested and avg cycles:
- Word Copies + Loop Unrolls + Non Aligned 1882
- Word Copies + Loop Unrolls 1887
- Word Copies 2441
- Byte Copies + Loop Unrolls 6467
- Byte Copies 7600
In the end I ended up going with Word Copies + Loop Unrolls as it
provides best tradeoff between simplicity and boot speedups.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This adds a hand-optimized assembler version of memset and sets
__HAVE_ARCH_MEMSET to use this version instead of the generic C
routine
Signed-off-by: Olof Kindgren <olof.kindgren@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This patch adds basic support for the idle state of the cpu.
The patch overrides the regular idle function, enables the interupts,
checks for the power management unit and enables the cpu doze mode
if available.
Signed-off-by: Sebastian Macke <sebastian@macke.de>
[shorne@gmail.com: Fixed checkpatch, blankline after declarations]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The bits were swapped, as per spec and processor implementation the
power management present bit is 9 and PIC bit is 8. This patch brings
the definitions into spec.
Signed-off-by: Sebastian Macke <sebastian@macke.de>
[shorne@gmail.com: Added commit body]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This causes the build to fail when building with the or1k-musl-linux-
toolchain and it is not needed.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Support for the futex_atomic_* operations by using the
load-link/store-conditional l.lwa/l.swa instructions.
Most openrisc cores provide these instructions now if not available,
emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Using the l.lwa and l.swa atomic instruction pair.
Most openrisc processor cores provide these instructions now. If the
instructions are not available emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666]
[shorne@gmail.com: expand to implement all ops suggested by Peter
Zijlstra https://lkml.org/lkml/2017/2/20/317]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Optimized version that make use of the l.lwa and l.swa atomic instruction
pair.
Most openrisc cores provide these instructions now, if not available
emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666]
[shorne@gmail.com: fixed unused calculated value compiler warning in
define cmpxchg]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This utilize the load-link/store-conditional l.lwa and l.swa
instructions to implement the atomic bitops.
When those instructions are not available emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666, implement
test_and_change_bit]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Patch "sparc64: Add 64K page size support"
unconditionally used __flush_huge_tsb_one_entry()
which is available only when hugetlb support is
enabled.
Another issue was incorrect TSB flushing for 64K
pages in flush_tsb_user().
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_One
http://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wireless
https://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.html
http://www.savageboard.org/
http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ul
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver has
been merged into mainline.
There is now a new defconfig file for tango4"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: multi_v7_defconfig: enable pstore configs
ARM: multi_v7_defconfig: enable some newly added crypto modules
ARM: davinci_all_defconfig: enable SATA modules
arm64: defconfig: enable CONFIG_MTD_NAND and CONFIG_MTD_NAND_DENALI_DT
arm64: defconfig: enable CONFIG_MTD_BLOCK
ARM: Import tango4_defconfig
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
arm64: defconfig: Enable NUMA and NUMA_BALANCING
arm64: defconfig: enable SMMUv3 config
ARM: davinci_all_defconfig: enable iio
ARM: Keystone: Enable ARCH_HAS_RESET_CONTROLLER
ARM: configs: stm32: Add RTC support in STM32 defconfig
ARM: defconfig: qcom: add APQ8060 DragonBoard devices
ARM: qcom_defconfig: enable thermal sensors
ARM: qcom_defconfig: add ahci configs
ARM: qcom_defconfig: add pcie and atl1c ethernet configs
ARM: qcom_defconfig: add usb related configs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms, only trivial stuff
this time, a few defconfig changes to enable drivers, and a new entry
for the Cavium ThunderX2 platform"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add Cavium ThunderX2 entry
arm64: add ARCH_THUNDER2 to defconfig
arm64: add THUNDER2 processor family
MAINTAINERS: Extend ARM/Mediatek SoC support section
arm64: defconfig: enable CONFIG_MMC_SDHCI_CADENCE
arm64: defconfig: enable XORv2 for Marvell Armada 7K/8K
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"In the SoC branch we normally collect classic arch/arm/mach-*
contents, i.e. C code changes for SoC platforms. This release cycle
the diffstat is quite nice, in that we're removing 3x the amount of
code that's being added.
The main reason for this is that there's a removal of camera drivers
for Freescale i.MX chips (driver was removed so the device
registration isn't needed any more). There's also removal of display
initialization code for OMAP that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on
Samsung platforms, cleanup of ux500 platform data, purge of other
unused platform data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and
V3s"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: ux500: remove deleted file from Makefile
ARM: ep93xx: Disable TS-72xx watchdog before uncompressing
ARM: ux500: cut some platform data
MAINTAINERS: Update for the current location of the bcm2835 tree.
ARM: davinci: remove BUG_ON() from da850_register_sata()
ARM: davinci: da850: model the SATA refclk
ARM: davinci: da850: add con_id for the SATA clock
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for SATA
arm: mvebu: support for SMP on 98DX3336 SoC
dt-bindings: video: exynos7-decon: Remove obsolete samsung,power-domain property
soc: dove: constify reset_control_ops structures
ARM: mv78xx0: fix possible PCI buffer overflow
MAINTAINERS: transfer maintainership for the EZX platform
ARM: shmobile: rcar-gen2: Add more register documentation
ARM: tegra: paz00: Fix __initdata placement
ARM: OMAP: clock: Remove unused mpurate cmdline option
ARM: davinci: add skeleton for pdata-quirks
arm: sunxi: add support for V3s SoC
ARM: OMAP2+: omap_hwmod: Add support for earlycon
arm: hisi: drop extern hip01_cpu_die
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"We sometimes collect non-critical fixes that come in during the later
part of the merge window in a branch for the next release instead, and
this is that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for
SCPI to only enable on ARM{,64}"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
firmware: arm_scpi: Add hardware dependencies
ARM: OMAP3: Fix SoC detection of OMAP36/37 Family
ARM: OMAP5: Add HWMOD_SWSUP_SIDLE_ACT flag for UART
ARM: dts: Fix compatible for ti81xx uarts for 8250
ARM: dts: Fix am335x and dm814x scm syscon to probe children
ARM: OMAP2+: Fix init for multiple quirks for the same SoC
ARM: dts: Fix omap3 off mode pull defines
bus: da850-mstpri: fix my e-mail address
ARM: davinci: da850: fix da850_set_pll0rate()
ARM: davinci: da850: coding style fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Try to catch hash output overrun in testmgr
- Introduce walksize attribute for batched walking
- Make crypto_xor() and crypto_inc() alignment agnostic
Algorithms:
- Add time-invariant AES algorithm
- Add standalone CBCMAC algorithm
Drivers:
- Add NEON acclerated chacha20 on ARM/ARM64
- Expose AES-CTR as synchronous skcipher on ARM64
- Add scalar AES implementation on ARM64
- Improve scalar AES implementation on ARM
- Improve NEON AES implementation on ARM/ARM64
- Merge CRC32 and PMULL instruction based drivers on ARM64
- Add NEON acclerated CBCMAC/CMAC/XCBC AES on ARM64
- Add IPsec AUTHENC implementation in atmel
- Add Support for Octeon-tx CPT Engine
- Add Broadcom SPU driver
- Add MediaTek driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (142 commits)
crypto: xts - Add ECB dependency
crypto: cavium - switch to pci_alloc_irq_vectors
crypto: cavium - switch to pci_alloc_irq_vectors
crypto: cavium - remove dead MSI-X related define
crypto: brcm - Avoid double free in ahash_finup()
crypto: cavium - fix Kconfig dependencies
crypto: cavium - cpt_bind_vq_to_grp could return an error code
crypto: doc - fix typo
hwrng: omap - update Kconfig help description
crypto: ccm - drop unnecessary minimum 32-bit alignment
crypto: ccm - honour alignmask of subordinate MAC cipher
crypto: caam - fix state buffer DMA (un)mapping
crypto: caam - abstract ahash request double buffering
crypto: caam - fix error path for ctx_dma mapping failure
crypto: caam - fix DMA API leaks for multiple setkey() calls
crypto: caam - don't dma_map key for hash algorithms
crypto: caam - use dma_map_sg() return code
crypto: caam - replace sg_count() with sg_nents_for_len()
crypto: caam - check sg_count() return value
crypto: caam - fix HW S/G in ablkcipher_giv_edesc_alloc()
..
|
