| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes before final release:
Marvell Armada:
- One to fix a typo in the devicetree specifying memory ranges for
the crypto engine
- Two to deal with marking PCI and device-memory as strongly ordered
to avoid hardware deadlocks, in particular when enabling above
crypto driver.
- Compile fix for PM
Allwinner:
- DT clock fixes to deal with u-boot-enabled framebuffer (simplefb).
- Make R8 (C.H.I.P. SoC) inherit system compatibility from A13 to
make clocks register proper.
Tegra:
- Fix SD card voltage setting on the Tegra3 Beaver dev board
Misc:
- Two maintainers updates for STM32 and STi platforms"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: beaver: Allow SD card voltage to be changed
MAINTAINERS: update STi maintainer list
MAINTAINERS: update STM32 maintainers list
ARM: mvebu: compile pm code conditionally
ARM: dts: sun7i: Fix pll3x2 and pll7x2 not having a parent clock
ARM: dts: sunxi: Add pll3 to simplefb nodes clocks lists
ARM: dts: armada-38x: fix MBUS_ID for crypto SRAM on Armada 385 Linksys
ARM: mvebu: map PCI I/O regions strongly ordered
ARM: mvebu: fix HW I/O coherency related deadlocks
ARM: sunxi/dt: make the CHIP inherit from allwinner,sun5i-a13
|
|
We were getting build warning:
arch/m32r/boot/compressed/m32r_sio.c:11:13:
warning: conflicting types for built-in function 'putc'
Here putc is used as a static function so lets just rename it to avoid
the conflict with the builtin putc.
Link: http://lkml.kernel.org/r/1466977046-24724-1-git-send-email-sudipm.mukherjee@gmail.com
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently GPF messages with KASAN look as follows:
kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
Add newlines.
Link: http://lkml.kernel.org/r/1467294357-98002-1-git-send-email-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf and timer fixes from Ingo Molnar:
"A fix for a posix CPU timers bug, and a perf printk message fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix bogus kernel printk, again
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix_cpu_timer: Exit early when process has been reaped
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This contains three commits to fix memory corruption bugs with certain
Apple AirPort cards, plus a fix for a X86_BUG() ID definitions collision
bug in asm/cpufeatures.h"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/quirks: Add early quirk to reset Apple AirPort card
x86/quirks: Reintroduce scanning of secondary buses
x86/quirks: Apply nvidia_bugs quirk only on root bus
x86/cpu: Fix duplicated X86_BUG(9) macro
|
|
The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.
The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.
The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.
When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56
This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.
Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.
Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.
The following should be a comprehensive list of affected models:
iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16]
iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16]
Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12]
Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12]
MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):
irq 17: nobody cared (try booting with the "irqpoll" option)
handlers:
[<ffffffff81374370>] pcie_isr
[<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci]
[<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec]
Disabling IRQ #17
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732
Tested-by: Konstantin Simanov <k.simanov@stlk.ru> # [MacBookPro8,1]
Tested-by: Lukas Wunner <lukas@wunner.de> # [MacBookPro9,1]
Tested-by: Bryan Paradis <bryan.paradis@gmail.com> # [MacBookPro9,2]
Tested-by: Andrew Worsley <amworsley@gmail.com> # [MacBookPro10,1]
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris Milsted <cmilsted@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: b43-dev@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Apply nvidia_bugs quirk only on root bus
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Reintroduce scanning of secondary buses
Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de
[ Did minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We used to scan secondary buses until the following commit that
was applied in 2009:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.
We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.
The commit message of 8659c406ade3 notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406ade3 was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.
Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.
If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since the following commit:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
... early quirks are only applied to devices on the root bus.
The motivation was to prevent application of the nvidia_bugs quirk on
secondary buses.
We're about to reintroduce scanning of secondary buses for a quirk to
reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent
regressions, open code the requirement to apply nvidia_bugs only on the
root bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4d5477c1d76b2f0387a780f2142bbcdd9fee869b.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This showed up as "6Failed to access..." here.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 1b74dde7c47c ("x86/cpu: Convert printk(KERN_<LEVEL> ...) to pr_<level>(...)")
Link: http://lkml.kernel.org/r/1468170841-17045-1-git-send-email-vegard.nossum@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull MIPS fix from Ralf Baechle:
"Another week with just a single 4.7 fix.
This fixes a possible 'loss' of the huge page bit from pmd on
permission change"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix page table corruption on THP permission changes.
|
|
cpufeatures.h currently defines X86_BUG(9) twice on 32-bit:
#define X86_BUG_NULL_SEG X86_BUG(9) /* Nulling a selector preserves the base */
...
#ifdef CONFIG_X86_32
#define X86_BUG_ESPFIX X86_BUG(9) /* "" IRET to 16-bit SS corrupts ESP/RSP high bits */
#endif
I think what happened was that this added the X86_BUG_ESPFIX, but
in an #ifdef below most of the bugs:
58a5aac53313 x86/entry/32: Introduce and use X86_BUG_ESPFIX instead of paravirt_enabled
Then this came along and added X86_BUG_NULL_SEG, but collided
with the earlier one that did the bug below the main block
defining all the X86_BUG()s.
7a5d67048745 x86/cpu: Probe the behavior of nulling out a segment at boot time
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160618001503.CEE1B141@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A couple of late fixes here, but one that we've been sitting on for a
few weeks while the details were worked out. Specifically, we now
enforce USER_DS on taking exceptions whilst in the kernel, which
avoids leaking kernel data to userspace through things like perf. The
other patch is an update to a workaround for a hardware erratum on
some Cavium SoCs.
Summary:
- Enforce USER_DS on exception entry from EL1
- Apply workaround for Cavium errata #27456 on Thunderx-81xx parts"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Enable workaround for Cavium erratum 27456 on thunderx-81xx
arm64: kernel: Save and restore UAO and addr_limit on exception entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Three fixes:
- A boot crash fix with certain configs
- a MAINTAINERS entry update
- Documentation typo fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Documentation: Fix various typos in Documentation/x86/ files
x86/amd_nb: Fix boot crash on non-AMD systems
MAINTAINERS: Update the Calgary IOMMU entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Various fixes:
- 32-bit callgraph bug fix
- suboptimal event group scheduling bug fix
- event constraint fixes for Broadwell/Skylake
- RAPL module name collision fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix pmu::filter_match for SW-led groups
x86/perf/intel/rapl: Fix module name collision with powercap intel-rapl
perf/x86: Fix 32-bit perf user callgraph collection
perf/x86/intel: Update event constraints when HT is off
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"All of these fix recent regressions in ACPICA, in the ACPI PCI IRQ
management code and in the ACPI AML debugger.
Specifics:
- Fix a lock ordering issue in ACPICA introduced by a recent commit
that attempted to fix a deadlock in the dynamic table loading code
which in turn appeared after changes related to the handling of
module-level AML also made in this cycle (Lv Zheng).
- Fix a recent regression in the ACPI IRQ management code that may
cause PCI drivers to be unable to register an IRQ if that IRQ
happens to be shared with a device on the ISA bus, like the
parallel port, by reverting one commit entirely and restoring the
previous behavior in two other places (Sinan Kaya).
- Fix a recent regression in the ACPI AML debugger introduced by the
commit that removed incorrect usage of IS_ERR_VALUE() from multiple
places (Lv Zheng)"
* tag 'acpi-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / debugger: Fix regression introduced by IS_ERR_VALUE() removal
ACPICA: Namespace: Fix namespace/interpreter lock ordering
ACPI,PCI,IRQ: separate ISA penalty calculation
Revert "ACPI, PCI, IRQ: remove redundant code in acpi_irq_penalty_init()"
ACPI,PCI,IRQ: factor in PCI possible
|
|
* acpica-fixes:
ACPICA: Namespace: Fix namespace/interpreter lock ordering
* acpi-pci-fixes:
ACPI,PCI,IRQ: separate ISA penalty calculation
Revert "ACPI, PCI, IRQ: remove redundant code in acpi_irq_penalty_init()"
ACPI,PCI,IRQ: factor in PCI possible
* acpi-debug-fixes:
ACPI / debugger: Fix regression introduced by IS_ERR_VALUE() removal
|
|
* pm-cpuidle-fixes:
cpuidle: Fix last_residency division
* pm-sleep-fixes:
x86/power/64: Fix kernel text mapping corruption during image restoration
|
|
Cavium erratum 27456 commit 104a0c02e8b1
("arm64: Add workaround for Cavium erratum 27456")
is applicable for thunderx-81xx pass1.0 SoC as well.
Adding code to enable to 81xx.
Signed-off-by: Ganapatrao Kulkarni <gkulkarni@cavium.com>
Reviewed-by: Andrew Pinski <apinski@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
If we take an exception while at EL1, the exception handler inherits
the original context's addr_limit and PSTATE.UAO values. To be consistent
always reset addr_limit and PSTATE.UAO on (re-)entry to EL1. This
prevents accidental re-use of the original context's addr_limit.
Based on a similar patch for arm from Russell King.
Cc: <stable@vger.kernel.org> # 4.6-
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This allows to switch the card signal voltage level to 1.8 V, which is
needed for any ultra high speed modes to work.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When the core THP code is modifying the permissions of a huge page it
calls pmd_modify(), which unfortunately was clearing the _PAGE_HUGE bit
of the page table entry. The result can be kernel messages like:
mm/memory.c:397: bad pmd 000000040080004d.
mm/memory.c:397: bad pmd 00000003ff00004d.
mm/memory.c:397: bad pmd 000000040100004d.
or:
------------[ cut here ]------------
WARNING: at mm/mmap.c:3200 exit_mmap+0x150/0x158()
Modules linked in: ipv6 at24 octeon3_ethernet octeon_srio_nexus m25p80
CPU: 12 PID: 1295 Comm: pmderr Not tainted 3.10.87-rt80-Cavium-Octeon #4
Stack : 0000000040808000 0000000014009ce1 0000000000400004 ffffffff81076ba0
0000000000000000 0000000000000000 ffffffff85110000 0000000000000119
0000000000000004 0000000000000000 0000000000000119 43617669756d2d4f
0000000000000000 ffffffff850fda40 ffffffff85110000 0000000000000000
0000000000000000 0000000000000009 ffffffff809207a0 0000000000000c80
ffffffff80f1bf20 0000000000000001 000000ffeca36828 0000000000000001
0000000000000000 0000000000000001 000000ffeca7e700 ffffffff80886924
80000003fd7a0000 80000003fd7a39b0 80000003fdea8000 ffffffff80885780
80000003fdea8000 ffffffff80f12218 000000000000000c 000000000000050f
0000000000000000 ffffffff80865c4c 0000000000000000 0000000000000000
...
Call Trace:
[<ffffffff80865c4c>] show_stack+0x6c/0xf8
[<ffffffff80885780>] warn_slowpath_common+0x78/0xa8
[<ffffffff809207a0>] exit_mmap+0x150/0x158
[<ffffffff80882d44>] mmput+0x5c/0x110
[<ffffffff8088b450>] do_exit+0x230/0xa68
[<ffffffff8088be34>] do_group_exit+0x54/0x1d0
[<ffffffff8088bfc0>] __wake_up_parent+0x0/0x18
---[ end trace c7b38293191c57dc ]---
BUG: Bad rss-counter state mm:80000003fa168000 idx:1 val:1536
Fix by not clearing _PAGE_HUGE bit.
Signed-off-by: David Daney <david.daney@cavium.com>
Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13687/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Since commit 4b6e2571bf00 the rapl perf module calls itself intel-rapl. That
name was already in use by the rapl powercap driver, which now fails to load
if the perf module is loaded. Fix the problem by renaming the perf module to
intel-rapl-perf, so that both modules can coexist.
Fixes: 4b6e2571bf00 ("x86/perf/intel/rapl: Make the Intel RAPL PMU driver modular")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1466694409-3620-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull "mvebu fixes for 4.7 (part 2)" from Gregory CLEMENT:
Fix a regression introduced by a cleanup on kirkwood_pm_init
* tag 'mvebu-fixes-4.7-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: compile pm code conditionally
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Pull "Allwinner Fixes for 4.7" from Maxime Ripard:
Two patches fixing simplefb on the SoCs that had their display clocks
enabled, and one fix for the CHIP that will enable its sched clock.
* tag 'sunxi-fixes-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun7i: Fix pll3x2 and pll7x2 not having a parent clock
ARM: dts: sunxi: Add pll3 to simplefb nodes clocks lists
ARM: sunxi/dt: make the CHIP inherit from allwinner,sun5i-a13
|
|
A basic perf callgraph record operation causes an immediate panic on a
32-bit kernel compiled with CONFIG_CC_STACKPROTECTOR=y:
$ perf record -g ls
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: c0404fbd
CPU: 0 PID: 998 Comm: ls Not tainted 4.7.0-rc5+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.1-1.fc24 04/01/2014
c0dd5967 ff7afe1c 00000086 f41dbc2c c07445a0 464c457f f41dbca8 f41dbc44
c05646f4 f41dbca8 464c457f f41dbca8 464c457f f41dbc54 c04625be c0ce56fc
c0404fbd f41dbc88 c0404fbd b74668f0 f41dc000 00000000 c0000000 00000000
Call Trace:
[<c07445a0>] dump_stack+0x58/0x78
[<c05646f4>] panic+0x8e/0x1c6
[<c04625be>] __stack_chk_fail+0x1e/0x30
[<c0404fbd>] ? perf_callchain_user+0x22d/0x230
[<c0404fbd>] perf_callchain_user+0x22d/0x230
[<c055f89f>] get_perf_callchain+0x1ff/0x270
[<c055f988>] perf_callchain+0x78/0x90
[<c055c7eb>] perf_prepare_sample+0x24b/0x370
[<c055c934>] perf_event_output_forward+0x24/0x70
[<c05531c0>] __perf_event_overflow+0xa0/0x210
[<c0550a93>] ? cpu_clock_event_read+0x43/0x50
[<c0553431>] perf_swevent_hrtimer+0x101/0x180
[<c0456235>] ? kmap_atomic_prot+0x35/0x140
[<c056dc69>] ? get_page_from_freelist+0x279/0x950
[<c058fdd8>] ? vma_interval_tree_remove+0x158/0x230
[<c05939f4>] ? wp_page_copy.isra.82+0x2f4/0x630
[<c05a050d>] ? page_add_file_rmap+0x1d/0x50
[<c0565611>] ? unlock_page+0x61/0x80
[<c0566755>] ? filemap_map_pages+0x305/0x320
[<c059769f>] ? handle_mm_fault+0xb7f/0x1560
[<c074cbeb>] ? timerqueue_del+0x1b/0x70
[<c04cfefe>] ? __remove_hrtimer+0x2e/0x60
[<c04d017b>] __hrtimer_run_queues+0xcb/0x2a0
[<c0553330>] ? __perf_event_overflow+0x210/0x210
[<c04d0a2a>] hrtimer_interrupt+0x8a/0x180
[<c043ecc2>] local_apic_timer_interrupt+0x32/0x60
[<c043f643>] smp_apic_timer_interrupt+0x33/0x50
[<c0b0cd38>] apic_timer_interrupt+0x34/0x3c
Kernel Offset: disabled
---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: c0404fbd
The panic is caused by the fact that perf_callchain_user() mistakenly
assumes it's 64-bit only and ends up corrupting the stack.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org # v4.5+
Fixes: 75925e1ad7f5 ("perf/x86: Optimize stack walk user accesses")
Link: http://lkml.kernel.org/r/1a547f5077ec30f75f9b57074837c3c80df86e5e.1467432113.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch updates the event constraints for non-PEBS mode for
Intel Broadwell and Skylake processors. When HT is off, each
CPU gets 8 generic counters. However, not all events can be
programmed on any of the 8 counters. This patch adds the
constraints for the MEM_* events which can only be measured on the
bottom 4 counters. The constraints are also valid when HT is off
because, then, there are only 4 generic counters and they are the
bottom counters.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Link: http://lkml.kernel.org/r/1467411742-13245-1-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull MIPS fix from Ralf Baechle:
"Only a single fix for 4.7 pending at this point. It fixes an issue
that may lead to corruption of the cache mode bits in the page table"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix possible corruption of cache mode by mprotect.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- tm: Always reclaim in start_thread() for exec() class syscalls from
Cyril Bur
- tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0 from Michael
Neuling
- eeh: Fix wrong argument passed to eeh_rmv_device() from Gavin Shan
- Initialise pci_io_base as early as possible from Darren Stevens
* tag 'powerpc-4.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Initialise pci_io_base as early as possible
powerpc/tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0
powerpc/eeh: Fix wrong argument passed to eeh_rmv_device()
powerpc/tm: Always reclaim in start_thread() for exec() class syscalls
|
|
The following testcase may result in a page table entries with a invalid
CCA field being generated:
static void *bindstack;
static int sysrqfd;
static void protect_low(int protect)
{
mprotect(bindstack, BINDSTACK_SIZE, protect);
}
static void sigbus_handler(int signal, siginfo_t * info, void *context)
{
void *addr = info->si_addr;
write(sysrqfd, "x", 1);
printf("sigbus, fault address %p (should not happen, but might)\n",
addr);
abort();
}
static void run_bind_test(void)
{
unsigned int *p = bindstack;
p[0] = 0xf001f001;
write(sysrqfd, "x", 1);
/* Set trap on access to p[0] */
protect_low(PROT_NONE);
write(sysrqfd, "x", 1);
/* Clear trap on access to p[0] */
protect_low(PROT_READ | PROT_WRITE | PROT_EXEC);
write(sysrqfd, "x", 1);
/* Check the contents of p[0] */
if (p[0] != 0xf001f001) {
write(sysrqfd, "x", 1);
/* Reached, but shouldn't be */
printf("badness, shouldn't happen but does\n");
abort();
}
}
int main(void)
{
struct sigaction sa;
sysrqfd = open("/proc/sysrq-trigger", O_WRONLY);
if (sigprocmask(SIG_BLOCK, NULL, &sa.sa_mask)) {
perror("sigprocmask");
return 0;
}
sa.sa_sigaction = sigbus_handler;
sa.sa_flags = SA_SIGINFO | SA_NODEFER | SA_RESTART;
if (sigaction(SIGBUS, &sa, NULL)) {
perror("sigaction");
return 0;
}
bindstack = mmap(NULL,
BINDSTACK_SIZE,
PROT_READ | PROT_WRITE | PROT_EXEC,
MAP_PRIVATE | MAP_ANONYMOUS, -1, 0);
if (bindstack == MAP_FAILED) {
perror("mmap bindstack");
return 0;
}
printf("bindstack: %p\n", bindstack);
run_bind_test();
printf("done\n");
return 0;
}
There are multiple ingredients for this:
1) PAGE_NONE is defined to _CACHE_CACHABLE_NONCOHERENT, which is CCA 3
on all platforms except SB1 where it's CCA 5.
2) _page_cachable_default must have bits set which are not set
_CACHE_CACHABLE_NONCOHERENT.
3) Either the defective version of pte_modify for XPA or the standard
version must be in used. However pte_modify for the 36 bit address
space support is no affected.
In that case additional bits in the final CCA mode may generate an invalid
value for the CCA field. On the R10000 system where this was tracked
down for example a CCA 7 has been observed, which is Uncached Accelerated.
Fixed by:
1) Using the proper CCA mode for PAGE_NONE just like for all the other
PAGE_* pte/pmd bits.
2) Fix the two affected variants of pte_modify.
Further code inspection also shows the same issue to exist in pmd_modify
which would affect huge page systems.
Issue in pte_modify tracked down by Alastair Bridgewater, PAGE_NONE
and pmd_modify issue found by me.
The history of this goes back beyond Linus' git history. Chris Dearman's
commit 351336929ccf222ae38ff0cb7a8dd5fd5c6236a0 ("[MIPS] Allow setting of
the cache attribute at run time.") missed the opportunity to fix this
but it was originally introduced in lmo commit
d523832cf12007b3242e50bb77d0c9e63e0b6518 ("Missing from last commit.")
and 32cc38229ac7538f2346918a09e75413e8861f87 ("New configuration option
CONFIG_MIPS_UNCACHED.")
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
|
|
Trying to make the ISA and PCI init functionality common turned out
to be a bad idea, because the ISA path depends on external
functionality.
Restore the previous behavior and limit the refactoring to PCI
interrupts only.
Fixes: 1fcb6a813c4f "ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()"
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix boot crash that triggers if this driver is built into a kernel and
run on non-AMD systems.
AMD northbridges users call amd_cache_northbridges() and it returns
a negative value to signal that we weren't able to cache/detect any
northbridges on the system.
At least, it should do so as all its callers expect it to do so. But it
does return a negative value only when kmalloc() fails.
Fix it to return -ENODEV if there are no NBs cached as otherwise, amd_nb
users like amd64_edac, for example, which relies on it to know whether
it should load or not, gets loaded on systems like Intel Xeons where it
shouldn't.
Reported-and-tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1466097230-5333-2-git-send-email-bp@alien8.de
Link: https://lkml.kernel.org/r/5761BEB0.9000807@cybernetics.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Logan Gunthorpe reports that hibernation stopped working reliably for
him after commit ab76f7b4ab23 (x86/mm: Set NX on gap between __ex_table
and rodata).
That turns out to be a consequence of a long-standing issue with the
64-bit image restoration code on x86, which is that the temporary
page tables set up by it to avoid page tables corruption when the
last bits of the image kernel's memory contents are copied into
their original page frames re-use the boot kernel's text mapping,
but that mapping may very well get corrupted just like any other
part of the page tables. Of course, if that happens, the final
jump to the image kernel's entry point will go to nowhere.
The exact reason why commit ab76f7b4ab23 matters here is that it
sometimes causes a PMD of a large page to be split into PTEs
that are allocated dynamically and get corrupted during image
restoration as described above.
To fix that issue note that the code copying the last bits of the
image kernel's memory contents to the page frames occupied by them
previoulsy doesn't use the kernel text mapping, because it runs from
a special page covered by the identity mapping set up for that code
from scratch. Hence, the kernel text mapping is only needed before
that code starts to run and then it will only be used just for the
final jump to the image kernel's entry point.
Accordingly, the temporary page tables set up in swsusp_arch_resume()
on x86-64 need to contain the kernel text mapping too. That mapping
is only going to be used for the final jump to the image kernel, so
it only needs to cover the image kernel's entry point, because the
first thing the image kernel does after getting control back is to
switch over to its own original page tables. Moreover, the virtual
address of the image kernel's entry point in that mapping has to be
the same as the one mapped by the image kernel's page tables.
With that in mind, modify the x86-64's arch_hibernation_header_save()
and arch_hibernation_header_restore() routines to pass the physical
address of the image kernel's entry point (in addition to its virtual
address) to the boot kernel (a small piece of assembly code involved
in passing the entry point's virtual address to the image kernel is
not necessary any more after that, so drop it). Update RESTORE_MAGIC
too to reflect the image header format change.
Next, in set_up_temporary_mappings(), use the physical and virtual
addresses of the image kernel's entry point passed in the image
header to set up a minimum kernel text mapping (using memory pages
that won't be overwritten by the image kernel's memory contents) that
will map those addresses to each other as appropriate.
This makes the concern about the possible corruption of the original
boot kernel text mapping go away and if the the minimum kernel text
mapping used for the final jump marks the image kernel's entry point
memory as executable, the jump to it is guaraneed to succeed.
Fixes: ab76f7b4ab23 (x86/mm: Set NX on gap between __ex_table and rodata)
Link: http://marc.info/?l=linux-pm&m=146372852823760&w=2
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull KVM fixes from Paolo Bonzini:
"ARM and x86 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: VMX instructions: fix segment checks when L1 is in long mode.
KVM: LAPIC: cap __delay at lapic_timer_advance_ns
KVM: x86: move nsec_to_cycles from x86.c to x86.h
pvclock: Get rid of __pvclock_read_cycles in function pvclock_read_flags
pvclock: Cleanup to remove function pvclock_get_nsec_offset
pvclock: Add CPU barriers to get correct version value
KVM: arm/arm64: Stop leaking vcpu pid references
arm64: KVM: fix build with CONFIG_ARM_PMU disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fix from Vineet Gupta:
"Reinstate dwarf unwinder/loadable-modules with new gnu tools"
* tag 'arc-4.7-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: unwind: warn only once if DW2_UNWIND is disabled
ARC: unwind: ensure that .debug_frame is generated (vs. .eh_frame)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM Fixes for v4.7-rc6:
Fixes a build issue without CONFIG_ARM_PMU and plugs pid leak on arm/arm64.
|
|
A cleanup to include the headers correctly caused another build problem:
arch/arm/mach-mvebu/kirkwood-pm.c:70:13: error: redefinition of 'kirkwood_pm_init'
arch/arm/mach-mvebu/kirkwood-pm.h:23:20: note: previous definition of 'kirkwood_pm_init' was here
The underlying issue is that kirkwood-pm.o is not actually meant to be
used when CONFIG_PM is disabled, so we should also leave it out of the
Makefile.
The same seems to be true for the PM code in MACH_MVEBU_V7, and I'm
treating it the same way here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d705c1a66e15 ("ARM: Kirkwood: fix kirkwood_pm_init() declaration/type")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Commit d6a9996e84ac ("powerpc/mm: vmalloc abstraction in preparation for
radix") turned kernel memory and IO addresses from #defined constants to
variables initialised at runtime.
On PA6T (pasemi) systems the setup_arch() machine call initialises the
onboard PCI-e root-ports, and uses pci_io_base to do this, which is now
before its value has been set, resulting in a panic early in boot before
console IO is initialised.
Move the pci_io_base initialisation to the same place as vmalloc ranges
are set (hash__early_init_mmu()/radix__early_init_mmu()) - this is the
earliest possible place we can initialise it.
Fixes: d6a9996e84ac ("powerpc/mm: vmalloc abstraction in preparation for radix")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Add #ifdef CONFIG_PCI, massage change log slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Fix pll3x2 and pll7x2 not having a parent clock, specifically this
fixes the kernel turning of pll3 while simplefb is using it when
uboot has configured things to use pll3x2 as lcd ch clk parent.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Currently we have 2 segments that are bolted for the kernel linear
mapping (ie 0xc000... addresses). This is 0 to 1TB and also the kernel
stacks. Anything accessed outside of these regions may need to be
faulted in. (In practice machines with TM always have 1T segments)
If a machine has < 2TB of memory we never fault on the kernel linear
mapping as these two segments cover all physical memory. If a machine
has > 2TB of memory, there may be structures outside of these two
segments that need to be faulted in. This faulting can occur when
running as a guest as the hypervisor may remove any SLB that's not
bolted.
When we treclaim and trecheckpoint we have a window where we need to
run with the userspace GPRs. This means that we no longer have a valid
stack pointer in r1. For this window we therefore clear MSR RI to
indicate that any exceptions taken at this point won't be able to be
handled. This means that we can't take segment misses in this RI=0
window.
In this RI=0 region, we currently access the thread_struct for the
process being context switched to or from. This thread_struct access
may cause a segment fault since it's not guaranteed to be covered by
the two bolted segment entries described above.
We've seen this with a crash when running as a guest with > 2TB of
memory on PowerVM:
Unrecoverable exception 4100 at c00000000004f138
Oops: Unrecoverable exception, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 1280 PID: 7755 Comm: kworker/1280:1 Tainted: G X 4.4.13-46-default #1
task: c000189001df4210 ti: c000189001d5c000 task.ti: c000189001d5c000
NIP: c00000000004f138 LR: 0000000010003a24 CTR: 0000000010001b20
REGS: c000189001d5f730 TRAP: 4100 Tainted: G X (4.4.13-46-default)
MSR: 8000000100001031 <SF,ME,IR,DR,LE> CR: 24000048 XER: 00000000
CFAR: c00000000004ed18 SOFTE: 0
GPR00: ffffffffc58d7b60 c000189001d5f9b0 00000000100d7d00 000000003a738288
GPR04: 0000000000002781 0000000000000006 0000000000000000 c0000d1f4d889620
GPR08: 000000000000c350 00000000000008ab 00000000000008ab 00000000100d7af0
GPR12: 00000000100d7ae8 00003ffe787e67a0 0000000000000000 0000000000000211
GPR16: 0000000010001b20 0000000000000000 0000000000800000 00003ffe787df110
GPR20: 0000000000000001 00000000100d1e10 0000000000000000 00003ffe787df050
GPR24: 0000000000000003 0000000000010000 0000000000000000 00003fffe79e2e30
GPR28: 00003fffe79e2e68 00000000003d0f00 00003ffe787e67a0 00003ffe787de680
NIP [c00000000004f138] restore_gprs+0xd0/0x16c
LR [0000000010003a24] 0x10003a24
Call Trace:
[c000189001d5f9b0] [c000189001d5f9f0] 0xc000189001d5f9f0 (unreliable)
[c000189001d5fb90] [c00000000001583c] tm_recheckpoint+0x6c/0xa0
[c000189001d5fbd0] [c000000000015c40] __switch_to+0x2c0/0x350
[c000189001d5fc30] [c0000000007e647c] __schedule+0x32c/0x9c0
[c000189001d5fcb0] [c0000000007e6b58] schedule+0x48/0xc0
[c000189001d5fce0] [c0000000000deabc] worker_thread+0x22c/0x5b0
[c000189001d5fd80] [c0000000000e7000] kthread+0x110/0x130
[c000189001d5fe30] [c000000000009538] ret_from_kernel_thread+0x5c/0xa4
Instruction dump:
7cb103a6 7cc0e3a6 7ca222a6 78a58402 38c00800 7cc62838 08860000 7cc000a6
38a00006 78c60022 7cc62838 0b060000 <e8c701a0> 7ccff120 e8270078 e8a70098
---[ end trace 602126d0a1dedd54 ]---
This fixes this by copying the required data from the thread_struct to
the stack before we clear MSR RI. Then once we clear RI, we only access
the stack, guaranteeing there's no segment miss.
We also tighten the region over which we set RI=0 on the treclaim()
path. This may have a slight performance impact since we're adding an
mtmsr instruction.
Fixes: 090b9284d725 ("powerpc/tm: Clear MSR RI in non-recoverable TM code")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When calling eeh_rmv_device() in eeh_reset_device() for partial hotplug
case, @rmv_data instead of its address is the proper argument.
Otherwise, the stack frame is corrupted when writing to
@rmv_data (actually its address) in eeh_rmv_device(). It results in
kernel crash as observed.
This fixes the issue by passing @rmv_data, not its address to
eeh_rmv_device() in eeh_reset_device().
Fixes: 67086e32b564 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The test_fp_ctl function is used to test if a given value is a valid
floating-point control. The inline assembly in test_fp_ctl uses an
incorrect constraint for the 'orig_fpc' variable. If the compiler
chooses the same register for 'fpc' and 'orig_fpc' the test_fp_ctl()
function always returns true. This allows user space to trigger
kernel oopses with invalid floating-point control values on the
signal stack.
This problem has been introduced with git commit 4725c86055f5bbdcdf
"s390: fix save and restore of the floating-point-control register"
Cc: stable@vger.kernel.org # v3.13+
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This reverts commit 852ffd0f4e23248b47531058e531066a988434b5.
There are use cases where an intermediate boot kernel (1) uses kexec
to boot the final production kernel (2). For this scenario we should
provide the original boot information to the production kernel (2).
Therefore clearing the boot information during kexec() should not
be done.
Cc: stable@vger.kernel.org # v3.17+
Reported-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
With recent binutils update to support dwarf CFI pseudo-ops in gas, we
now get .eh_frame vs. .debug_frame. Although the call frame info is
exactly the same in both, the CIE differs, which the current kernel
unwinder can't cope with.
This broke both the kernel unwinder as well as loadable modules (latter
because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in
the module loader)
The ideal solution would be to switch unwinder to .eh_frame.
For now however we can make do by just ensureing .debug_frame is
generated by removing -fasynchronous-unwind-tables
.eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables
.debug_frame generated with -gdwarf-2
Fixes STAR 9001058196
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
I couldn't get Xen to boot a L2 HVM when it was nested under KVM - it was
getting a GP(0) on a rather unspecial vmread from Xen:
(XEN) ----[ Xen-4.7.0-rc x86_64 debug=n Not tainted ]----
(XEN) CPU: 1
(XEN) RIP: e008:[<ffff82d0801e629e>] vmx_get_segment_register+0x14e/0x450
(XEN) RFLAGS: 0000000000010202 CONTEXT: hypervisor (d1v0)
(XEN) rax: ffff82d0801e6288 rbx: ffff83003ffbfb7c rcx: fffffffffffab928
(XEN) rdx: 0000000000000000 rsi: 0000000000000000 rdi: ffff83000bdd0000
(XEN) rbp: ffff83000bdd0000 rsp: ffff83003ffbfab0 r8: ffff830038813910
(XEN) r9: ffff83003faf3958 r10: 0000000a3b9f7640 r11: ffff83003f82d418
(XEN) r12: 0000000000000000 r13: ffff83003ffbffff r14: 0000000000004802
(XEN) r15: 0000000000000008 cr0: 0000000080050033 cr4: 00000000001526e0
(XEN) cr3: 000000003fc79000 cr2: 0000000000000000
(XEN) ds: 0000 es: 0000 fs: 0000 gs: 0000 ss: 0000 cs: e008
(XEN) Xen code around <ffff82d0801e629e> (vmx_get_segment_register+0x14e/0x450):
(XEN) 00 00 41 be 02 48 00 00 <44> 0f 78 74 24 08 0f 86 38 56 00 00 b8 08 68 00
(XEN) Xen stack trace from rsp=ffff83003ffbfab0:
...
(XEN) Xen call trace:
(XEN) [<ffff82d0801e629e>] vmx_get_segment_register+0x14e/0x450
(XEN) [<ffff82d0801f3695>] get_page_from_gfn_p2m+0x165/0x300
(XEN) [<ffff82d0801bfe32>] hvmemul_get_seg_reg+0x52/0x60
(XEN) [<ffff82d0801bfe93>] hvm_emulate_prepare+0x53/0x70
(XEN) [<ffff82d0801ccacb>] handle_mmio+0x2b/0xd0
(XEN) [<ffff82d0801be591>] emulate.c#_hvm_emulate_one+0x111/0x2c0
(XEN) [<ffff82d0801cd6a4>] handle_hvm_io_completion+0x274/0x2a0
(XEN) [<ffff82d0801f334a>] __get_gfn_type_access+0xfa/0x270
(XEN) [<ffff82d08012f3bb>] timer.c#add_entry+0x4b/0xb0
(XEN) [<ffff82d08012f80c>] timer.c#remove_entry+0x7c/0x90
(XEN) [<ffff82d0801c8433>] hvm_do_resume+0x23/0x140
(XEN) [<ffff82d0801e4fe7>] vmx_do_resume+0xa7/0x140
(XEN) [<ffff82d080164aeb>] context_switch+0x13b/0xe40
(XEN) [<ffff82d080128e6e>] schedule.c#schedule+0x22e/0x570
(XEN) [<ffff82d08012c0cc>] softirq.c#__do_softirq+0x5c/0x90
(XEN) [<ffff82d0801602c5>] domain.c#idle_loop+0x25/0x50
(XEN)
(XEN)
(XEN) ****************************************
(XEN) Panic on CPU 1:
(XEN) GENERAL PROTECTION FAULT
(XEN) [error_code=0000]
(XEN) ****************************************
Tracing my host KVM showed it was the one injecting the GP(0) when
emulating the VMREAD and checking the destination segment permissions in
get_vmx_mem_address():
3) | vmx_handle_exit() {
3) | handle_vmread() {
3) | nested_vmx_check_permission() {
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.065 us | vmx_read_guest_seg_selector();
3) 0.066 us | vmx_read_guest_seg_ar();
3) 1.636 us | }
3) 0.058 us | vmx_get_rflags();
3) 0.062 us | vmx_read_guest_seg_ar();
3) 3.469 us | }
3) | vmx_get_cs_db_l_bits() {
3) 0.058 us | vmx_read_guest_seg_ar();
3) 0.662 us | }
3) | get_vmx_mem_address() {
3) 0.068 us | vmx_cache_reg();
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.068 us | vmx_read_guest_seg_selector();
3) 0.071 us | vmx_read_guest_seg_ar();
3) 1.756 us | }
3) | kvm_queue_exception_e() {
3) 0.066 us | kvm_multiple_exception();
3) 0.684 us | }
3) 4.085 us | }
3) 9.833 us | }
3) + 10.366 us | }
Cross-checking the KVM/VMX VMREAD emulation code with the Intel Software
Developper Manual Volume 3C - "VMREAD - Read Field from Virtual-Machine
Control Structure", I found that we're enforcing that the destination
operand is NOT located in a read-only data segment or any code segment when
the L1 is in long mode - BUT that check should only happen when it is in
protected mode.
Shuffling the code a bit to make our emulation follow the specification
allows me to boot a Xen dom0 in a nested KVM and start HVM L2 guests
without problems.
Fixes: f9eb4af67c9d ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Eugene Korenevsky <ekorenevsky@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The host timer which emulates the guest LAPIC TSC deadline
timer has its expiration diminished by lapic_timer_advance_ns
nanoseconds. Therefore if, at wait_lapic_expire, a difference
larger than lapic_timer_advance_ns is encountered, delay at most
lapic_timer_advance_ns.
This fixes a problem where the guest can cause the host
to delay for large amounts of time.
Reported-by: Alan Jenkins <alan.christopher.jenkins@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the inline function nsec_to_cycles from x86.c to x86.h, as
the next patch uses it from lapic.c.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There is a generic function __pvclock_read_cycles to be used to get both
flags and cycles. For function pvclock_read_flags, it's useless to get
cycles value. To make this function be more effective, get this variable
flags directly in function.
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Function __pvclock_read_cycles is short enough, so there is no need to
have another function pvclock_get_nsec_offset to calculate tsc delta.
It's better to combine it into function __pvclock_read_cycles.
Remove useless variables in function __pvclock_read_cycles.
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Protocol for the "version" fields is: hypervisor raises it (making it
uneven) before it starts updating the fields and raises it again (making
it even) when it is done. Thus the guest can make sure the time values
it got are consistent by checking the version before and after reading
them.
Add CPU barries after getting version value just like what function
vread_pvclock does, because all of callees in this function is inline.
Fixes: 502dfeff239e8313bfbe906ca0a1a6827ac8481b
Cc: stable@vger.kernel.org
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
