| Age | Commit message (Collapse) | Author |
|---|
|
The memory ordering comment no longer applies, because mm_ctx_id is
no longer used anywhere. At best always been difficult to follow.
It's better to consider the load on which the slbmte depends on, which
the MMU depends on before it can start loading TLBs, rather than a
store which may or may not have a subsequent dependency chain to the
slbmte.
So update the comment and we use the load of the mm's user context ID.
This is much more analogous the radix ordering too, which is good.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210421151733.212858-1-npiggin@gmail.com
|
|
Memory events (mem-loads and mem-stores) currently use the threshold
event selection as issue to finish. Power10 supports issue to complete
as part of thresholding which is more appropriate for mem-loads and
mem-stores. Hence fix the event code for memory events to use issue
to complete.
Fixes: a64e697cef23 ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1614840015-1535-1-git-send-email-atrajeev@linux.vnet.ibm.com
|
|
Sampled Instruction Event Register (SIER) field [46:48] identifies the
sampled instruction type. ISA v3.1 says value of 0b111 for this field as
reserved, but in POWER10 it denotes LARX/STCX type which will hopefully
be fixed in ISA v3.1 update.
Patch fixes the functions to handle type value 7 for CPU_FTR_ARCH_31.
Fixes: a64e697cef23 ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
[mpe: Avoid reading mmcra until necessary, use early return to deindent if block]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1614858937-1485-1-git-send-email-atrajeev@linux.vnet.ibm.com
|
|
[ 0.000000] ioremap() called early from find_legacy_serial_ports+0x3cc/0x474. Use early_ioremap() instead
find_legacy_serial_ports() is called early from setup_arch(), before
paging_init(). vmalloc is not available yet, ioremap shouldn't be
used that early.
Use early_ioremap() and switch to a regular ioremap() later.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/103ed8ee9e5973c958ec1da2d0b0764f69395d01.1618925560.git.christophe.leroy@csgroup.eu
|
|
At the time being, the fixmap area is defined at the top of
the address space or just below KASAN.
This definition is not valid for PPC64.
For PPC64, use the top of the I/O space.
Because of circular dependencies, it is not possible to include
asm/fixmap.h in asm/book3s/64/pgtable.h , so define a fixed size
AREA at the top of the I/O space for fixmap and ensure during
build that the size is big enough.
Fixes: 265c3491c4bc ("powerpc: Add support for GENERIC_EARLY_IOREMAP")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0d51620eacf036d683d1a3c41328f69adb601dc0.1618925560.git.christophe.leroy@csgroup.eu
|
|
On a kernel config with ALTIVEC=y and PPC_FPU not set/enabled,
there are build errors:
drivers/cpufreq/pmac32-cpufreq.c:262:2: error: implicit declaration of function 'enable_kernel_fp' [-Werror,-Wimplicit-function-declaration]
enable_kernel_fp();
../arch/powerpc/lib/sstep.c: In function 'do_vec_load':
../arch/powerpc/lib/sstep.c:637:3: error: implicit declaration of function 'put_vr' [-Werror=implicit-function-declaration]
637 | put_vr(rn, &u.v);
| ^~~~~~
../arch/powerpc/lib/sstep.c: In function 'do_vec_store':
../arch/powerpc/lib/sstep.c:660:3: error: implicit declaration of function 'get_vr'; did you mean 'get_oc'? [-Werror=implicit-function-declaration]
660 | get_vr(rn, &u.v);
| ^~~~~~
In theory ALTIVEC is independent of PPC_FPU but in practice nobody
is going to build such a machine, so make ALTIVEC require PPC_FPU
by selecting it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210421210647.20836-1-rdunlap@infradead.org
|
|
FA_DUMP (Firmware Assisted Dump) is a powerpc only feature that should
be enabled in our defconfig to get some build / test coverage.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210420042209.1641634-1-mpe@ellerman.id.au
|
|
opal_mpipl_query_tag() takes a pointer to a 64-bit value, which firmware
writes a value to. As OPAL is traditionally big endian this value will
be big endian.
This can be confirmed by looking at the implementation in skiboot:
static uint64_t opal_mpipl_query_tag(enum opal_mpipl_tags tag, __be64 *tag_val)
{
...
*tag_val = cpu_to_be64(opal_mpipl_tags[tag]);
return OPAL_SUCCESS;
}
Fix the declaration to annotate that the value is big endian.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210421125402.1955013-2-mpe@ellerman.id.au
|
|
Sparse says:
arch/powerpc/kernel/fadump.c:48:16: warning: symbol 'fadump_kobj' was not declared. Should it be static?
arch/powerpc/kernel/fadump.c:55:27: warning: symbol 'crash_mrange_info' was not declared. Should it be static?
arch/powerpc/kernel/fadump.c:61:27: warning: symbol 'reserved_mrange_info' was not declared. Should it be static?
arch/powerpc/kernel/fadump.c:83:12: warning: symbol 'fadump_cma_init' was not declared. Should it be static?
And indeed none of them are used outside this file, they can all be made
static. Also fadump_kobj needs to be moved inside the ifdef where it's
used.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210421125402.1955013-1-mpe@ellerman.id.au
|
|
When probe_kernel_read_inst() was created, there was no good place to
put it, so a file called lib/inst.c was dedicated for it.
Since then, probe_kernel_read_inst() has been renamed
copy_inst_from_kernel_nofault(). And mm/maccess.h didn't exist at that
time. Today, mm/maccess.h is related to copy_from_kernel_nofault().
Move copy_inst_from_kernel_nofault() into mm/maccess.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/9655d8957313906b77b8db5700a0e33ce06f45e5.1618405715.git.christophe.leroy@csgroup.eu
|
|
When probe_kernel_read_inst() was created, it was to mimic
probe_kernel_read() function.
Since then, probe_kernel_read() has been renamed
copy_from_kernel_nofault().
Rename probe_kernel_read_inst() into copy_inst_from_kernel_nofault().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b783d1f7cdb8914992384a669a2af57051b6bdcf.1618405715.git.christophe.leroy@csgroup.eu
|
|
We have two independant versions of probe_kernel_read_inst(), one for
PPC32 and one for PPC64.
The PPC32 is identical to the first part of the PPC64 version.
The remaining part of PPC64 version is not relevant for PPC32, but
not contradictory, so we can easily have a common function with
the PPC64 part opted out via a IS_ENABLED(CONFIG_PPC64).
The only need is to add a version of ppc_inst_prefix() for PPC32.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f7b9dfddef3b3760182c7e5466356c121a293dc9.1618405715.git.christophe.leroy@csgroup.eu
|
|
Its name comes from former probe_user_read() function.
That function is now called copy_from_user_nofault().
probe_user_read_inst() uses copy_from_user_nofault() to read only
a few bytes. It is suboptimal.
It does the same as get_user_inst() but in addition disables
page faults.
But on the other hand, it is not used for the time being. So remove it
for now. If one day it is really needed, we can give it a new name
more in line with today's naming, and implement it using get_user_inst()
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/5f6f82572242a59bfee1e19a71194d8f7ef5fca4.1618405715.git.christophe.leroy@csgroup.eu
|
|
If the target of a function call is within 32 Mbytes distance, use a
standard function call with 'bl' instead of the 'lis/ori/mtlr/blrl'
sequence.
In the first pass, no memory has been allocated yet and the code
position is not known yet (image pointer is NULL). This pass is there
to calculate the amount of memory to allocate for the EBPF code, so
assume the 4 instructions sequence is required, so that enough memory
is allocated.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/74944a1e3e5cfecc141e440a6ccd37920e186b70.1618227846.git.christophe.leroy@csgroup.eu
|
|
Re-implement BPF_ALU64 | BPF_{LSH/RSH/ARSH} | BPF_X with branchless
implementation copied from misc_32.S.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/03167350b05b2fe8b741e53363ee37709d0f878d.1618227846.git.christophe.leroy@csgroup.eu
|
|
Replace <<== by <<=
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/34d12a4f75cb8b53a925fada5e7ddddd3b145203.1618227846.git.christophe.leroy@csgroup.eu
|
|
wrtspr() is a function to write an arbitrary value in a special
register. It is used on 8xx to write to SPRN_NRI, SPRN_EID and
SPRN_EIE. Writing any value to one of those will play with MSR EE
and MSR RI regardless of that value.
r0 is used many places in the generated code and using r0 for
that creates an unnecessary dependency of this instruction with
preceding ones using r0 in a few places in vmlinux.
r2 is most likely the most stable register as it contains the
pointer to 'current'.
Using r2 instead of r0 avoids that unnecessary dependency.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/69f9968f4b592fefda55227f0f7430ea612cc950.1611299687.git.christophe.leroy@csgroup.eu
|
|
When we hit an UE while using machine check safe copy routines,
ignore_event flag is set and the event is ignored by mce handler,
And the flag is also saved for defered handling and printing of
mce event information, But as of now saving of this flag is done
on checking if the effective address is provided or physical address
is calculated, which is not right.
Save ignore_event flag regardless of whether the effective address is
provided or physical address is calculated.
Without this change following log is seen, when the event is to be
ignored.
[ 512.971365] MCE: CPU1: machine check (Severe) UE Load/Store [Recovered]
[ 512.971509] MCE: CPU1: NIP: [c0000000000b67c0] memcpy+0x40/0x90
[ 512.971655] MCE: CPU1: Initiator CPU
[ 512.971739] MCE: CPU1: Unknown
[ 512.972209] MCE: CPU1: machine check (Severe) UE Load/Store [Recovered]
[ 512.972334] MCE: CPU1: NIP: [c0000000000b6808] memcpy+0x88/0x90
[ 512.972456] MCE: CPU1: Initiator CPU
[ 512.972534] MCE: CPU1: Unknown
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Reviewed-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210407045816.352276-1-ganeshgr@linux.ibm.com
|
|
For that, create a 32 bits version of patch_imm64_load_insns()
and create a patch_imm_load_insns() which calls
patch_imm32_load_insns() on PPC32 and patch_imm64_load_insns()
on PPC64.
Adapt optprobes_head.S for PPC32. Use PPC_LL/PPC_STL macros instead
of raw ld/std, opt out things linked to paca and use stmw/lmw to
save/restore registers.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bad58c66859b2a475c0ad516b53164ae3b4853cd.1618927318.git.christophe.leroy@csgroup.eu
|
|
In order to simplify use on PPC32, change ppc_inst_as_u64()
into ppc_inst_as_ulong() that returns the 32 bits instruction
on PPC32.
Will be used when porting OPTPROBES to PPC32.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/22cadf29620664b600b82026d2a72b8b23351777.1618927318.git.christophe.leroy@csgroup.eu
|
|
This patch makes use of trap types in irq.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f7f8c9f98c33eaea316755c7fef150d1d77e047d.1618847273.git.christophe.leroy@csgroup.eu
|
|
This patch makes use of trap types in head_book3s_32.S
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bd80ace67757f489fc4ecdb76dd1a71511daba94.1618847273.git.christophe.leroy@csgroup.eu
|
|
This patch makes use of trap types in head_8xx.S
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/e1147287bf6f2fb0693048fe8db0298c7870e419.1618847273.git.christophe.leroy@csgroup.eu
|
|
As of today, if the DDW is big enough to fit (1 << MAX_PHYSMEM_BITS)
it's possible to use direct DMA mapping even with pmem region.
But, if that happens, the window size (len) is set to (MAX_PHYSMEM_BITS
- page_shift) instead of MAX_PHYSMEM_BITS, causing a pagesize times
smaller DDW to be created, being insufficient for correct usage.
Fix this so the correct window size is used in this case.
Fixes: bf6e2d562bbc4 ("powerpc/dma: Fallback to dma_ops when persistent memory present")
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210420045404.438735-1-leobras.c@gmail.com
|
|
The changes to add KUAP support with the hash MMU broke booting of KVM
PR guests. The symptom is no visible progress of the guest, or possibly
just "SLOF" being printed to the qemu console.
Host code is still executing, but breaking into xmon might show a stack
trace such as:
__might_fault+0x84/0xe0 (unreliable)
kvm_read_guest+0x1c8/0x2f0 [kvm]
kvmppc_ld+0x1b8/0x2d0 [kvm]
kvmppc_load_last_inst+0x50/0xa0 [kvm]
kvmppc_exit_pr_progint+0x178/0x220 [kvm_pr]
kvmppc_handle_exit_pr+0x31c/0xe30 [kvm_pr]
after_sprg3_load+0x80/0x90 [kvm_pr]
kvmppc_vcpu_run_pr+0x104/0x260 [kvm_pr]
kvmppc_vcpu_run+0x34/0x48 [kvm]
kvm_arch_vcpu_ioctl_run+0x340/0x450 [kvm]
kvm_vcpu_ioctl+0x2ac/0x8c0 [kvm]
sys_ioctl+0x320/0x1060
system_call_exception+0x160/0x270
system_call_common+0xf0/0x27c
Bisect points to commit b2ff33a10c8b ("powerpc/book3s64/hash/kuap:
Enable kuap on hash"), but that's just the commit that enabled KUAP with
hash and made the bug visible.
The root cause seems to be that KVM PR is creating kernel mappings that
don't use the correct key, since we switched to using key 3.
We have a helper for adding the right key value, however it's designed
to take a pteflags variable, which the KVM code doesn't have. But we can
make it work by passing 0 for the pteflags, and tell it explicitly that
it should use the kernel key.
With that changed guests boot successfully.
Fixes: d94b827e89dc ("powerpc/book3s64/kuap: Use Key 3 for kernel mapping with hash translation")
Cc: stable@vger.kernel.org # v5.11+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210419120139.1455937-1-mpe@ellerman.id.au
|
|
RCU complains about us calling printk() from an offline CPU:
=============================
WARNING: suspicious RCU usage
5.12.0-rc7-02874-g7cf90e481cb8 #1 Not tainted
-----------------------------
kernel/locking/lockdep.c:3568 RCU-list traversed in non-reader section!!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc7-02874-g7cf90e481cb8 #1
Call Trace:
dump_stack+0xec/0x144 (unreliable)
lockdep_rcu_suspicious+0x124/0x144
__lock_acquire+0x1098/0x28b0
lock_acquire+0x128/0x600
_raw_spin_lock_irqsave+0x6c/0xc0
down_trylock+0x2c/0x70
__down_trylock_console_sem+0x60/0x140
vprintk_emit+0x1a8/0x4b0
vprintk_func+0xcc/0x200
printk+0x40/0x54
pseries_cpu_offline_self+0xc0/0x120
arch_cpu_idle_dead+0x54/0x70
do_idle+0x174/0x4a0
cpu_startup_entry+0x38/0x40
rest_init+0x268/0x388
start_kernel+0x748/0x790
start_here_common+0x1c/0x614
Which happens because by the time we get to rtas_stop_self() we are
already offline. In addition the message can be spammy, and is not that
helpful for users, so remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210418135413.1204031-1-mpe@ellerman.id.au
|
|
We have some interesting code in our Makefile to define _TASK_CPU, based
on awk'ing the value out of asm-offsets.h. It exists to circumvent some
circular header dependencies that prevent us from referring to
task_struct in the relevant code. See the comment around _TASK_CPU in
smp.h for more detail.
Maybe one day we can come up with a better solution, but for now we can
at least limit that logic to 32-bit, because it's not needed for 64-bit.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210418131641.1186227-1-mpe@ellerman.id.au
|
|
Currently, neither the vio_bus or vio_driver structures provide support
for a shutdown() routine.
Add support for shutdown() by allowing drivers to provide a
implementation via function pointer in their vio_driver struct and
provide a proper implementation in the driver template for the vio_bus
that calls a vio drivers shutdown() if defined.
In the case that no shutdown() is defined by a vio driver and a kexec is
in progress we implement a big hammer that calls remove() to ensure no
further DMA for the devices is possible.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210402001325.939668-1-tyreld@linux.ibm.com
|
|
PERF_SAMPLE_WEIGHT_STRUCT
Performance Monitoring Unit (PMU) registers in powerpc provides
information on cycles elapsed between different stages in the
pipeline. This can be used for application tuning. On ISA v3.1
platform, this information is exposed by sampling registers.
Patch adds kernel support to capture two of the cycle counters
as part of perf sample using the sample type:
PERF_SAMPLE_WEIGHT_STRUCT.
The power PMU function 'get_mem_weight' currently uses 64 bit weight
field of perf_sample_data to capture memory latency. But following the
introduction of PERF_SAMPLE_WEIGHT_TYPE, weight field could contain
64-bit or 32-bit value depending on the architexture support for
PERF_SAMPLE_WEIGHT_STRUCT. Patches uses WEIGHT_STRUCT to expose the
pipeline stage cycles info. Hence update the ppmu functions to work for
64-bit and 32-bit weight values.
If the sample type is PERF_SAMPLE_WEIGHT, use the 64-bit weight field.
if the sample type is PERF_SAMPLE_WEIGHT_STRUCT, memory subsystem
latency is stored in the low 32bits of perf_sample_weight structure.
Also for CPU_FTR_ARCH_31, capture the two cycle counter information in
two 16 bit fields of perf_sample_weight structure.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1616425047-1666-2-git-send-email-atrajeev@linux.vnet.ibm.com
|
|
The RTAS set-indicator call, when attempting to UNISOLATE a DRC that is
already UNISOLATED or CONFIGURED, returns RTAS_OK and does nothing else
for both QEMU and phyp. This gives us an opportunity to use this
behavior to signal the hypervisor layer when an error during device
removal happens, allowing it to do a proper error handling, while not
breaking QEMU/phyp implementations that don't have this support.
This patch introduces this idea by unisolating all CPU DRCs that failed
to be removed by dlpar_cpu_remove_by_index(), when handling the
PSERIES_HP_ELOG_ID_DRC_INDEX event. This is being done for this event
only because its the only CPU removal event QEMU uses, and there's no
need at this moment to add this mechanism for phyp only code.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210416210216.380291-3-danielhb413@gmail.com
|
|
Next patch will execute a set-indicator call in hotplug-cpu.c.
Create a dlpar_unisolate_drc() helper to avoid spreading more
rtas_set_indicator() calls outside of dlpar.c.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210416210216.380291-2-danielhb413@gmail.com
|
|
The error type is ICACHE not DCACHE, for case MCE_ERROR_TYPE_ICACHE.
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210416125750.49550-1-ganeshgr@linux.ibm.com
|
|
sfr reports that the allyesconfig build fails with:
arch/powerpc/kernel/fadump.c: In function 'crash_fadump':
arch/powerpc/kernel/fadump.c:731:28: error: 'INTERRUPT_SYSTEM_RESET' undeclared
731 | if (TRAP(&(fdh->regs)) == INTERRUPT_SYSTEM_RESET) {
Add an include of interrupt.h to fix it.
Fixes: 7153d4bf0b37 ("powerpc/traps: Enhance readability for trap types")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[mpe: Reformat change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210419191425.281dc58a@canb.auug.org.au
|
|
Add platform specific attr.config value checks. Patch
includes checks for both power9 and power10.
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210408074504.248211-2-maddy@linux.ibm.com
|
|
Merge some powerpc KVM patches we are keeping in a topic branch just in
case anyone else needs to merge them.
|
|
Starting with ISA v3.1, LPCR[AIL] no longer controls the interrupt
mode for HV=1 interrupts. Instead, a new LPCR[HAIL] bit is defined
which behaves like AIL=3 for HV interrupts when set.
Set HAIL on bare metal to give us mmu-on interrupts and improve
performance.
This also fixes an scv bug: we don't implement scv real mode (AIL=0)
vectors because they are at an inconvenient location, so we just
disable scv support when AIL can not be set. However powernv assumes
that LPCR[AIL] will enable AIL mode so it enables scv support despite
HV interrupts being AIL=0, which causes scv interrupts to go off into
the weeds.
Fixes: 7fa95f9adaee ("powerpc/64s: system call support for scv/rfscv instructions")
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210402024124.545826-1-npiggin@gmail.com
|
|
Geethika reported a trace when doing a dlpar CPU add.
------------[ cut here ]------------
WARNING: CPU: 152 PID: 1134 at kernel/sched/topology.c:2057
CPU: 152 PID: 1134 Comm: kworker/152:1 Not tainted 5.12.0-rc5-master #5
Workqueue: events cpuset_hotplug_workfn
NIP: c0000000001cfc14 LR: c0000000001cfc10 CTR: c0000000007e3420
REGS: c0000034a08eb260 TRAP: 0700 Not tainted (5.12.0-rc5-master+)
MSR: 8000000000029033 <SF,EE,ME,IR,DR,RI,LE> CR: 28828422 XER: 00000020
CFAR: c0000000001fd888 IRQMASK: 0 #012GPR00: c0000000001cfc10
c0000034a08eb500 c000000001f35400 0000000000000027 #012GPR04:
c0000035abaa8010 c0000035abb30a00 0000000000000027 c0000035abaa8018
#012GPR08: 0000000000000023 c0000035abaaef48 00000035aa540000
c0000035a49dffe8 #012GPR12: 0000000028828424 c0000035bf1a1c80
0000000000000497 0000000000000004 #012GPR16: c00000000347a258
0000000000000140 c00000000203d468 c000000001a1a490 #012GPR20:
c000000001f9c160 c0000034adf70920 c0000034aec9fd20 0000000100087bd3
#012GPR24: 0000000100087bd3 c0000035b3de09f8 0000000000000030
c0000035b3de09f8 #012GPR28: 0000000000000028 c00000000347a280
c0000034aefe0b00 c0000000010a2a68
NIP [c0000000001cfc14] build_sched_domains+0x6a4/0x1500
LR [c0000000001cfc10] build_sched_domains+0x6a0/0x1500
Call Trace:
[c0000034a08eb500] [c0000000001cfc10] build_sched_domains+0x6a0/0x1500 (unreliable)
[c0000034a08eb640] [c0000000001d1e6c] partition_sched_domains_locked+0x3ec/0x530
[c0000034a08eb6e0] [c0000000002936d4] rebuild_sched_domains_locked+0x524/0xbf0
[c0000034a08eb7e0] [c000000000296bb0] rebuild_sched_domains+0x40/0x70
[c0000034a08eb810] [c000000000296e74] cpuset_hotplug_workfn+0x294/0xe20
[c0000034a08ebc30] [c000000000178dd0] process_one_work+0x300/0x670
[c0000034a08ebd10] [c0000000001791b8] worker_thread+0x78/0x520
[c0000034a08ebda0] [c000000000185090] kthread+0x1a0/0x1b0
[c0000034a08ebe10] [c00000000000ccec] ret_from_kernel_thread+0x5c/0x70
Instruction dump:
7d2903a6 4e800421 e8410018 7f67db78 7fe6fb78 7f45d378 7f84e378 7c681b78
3c62ff1a 3863c6f8 4802dc35 60000000 <0fe00000> 3920fff4 f9210070 e86100a0
---[ end trace 532d9066d3d4d7ec ]---
Some of the per-CPU masks use cpu_cpu_mask as a filter to limit the search
for related CPUs. On a dlpar add of a CPU, update cpu_cpu_mask before
updating the per-CPU masks. This will ensure the cpu_cpu_mask is updated
correctly before its used in setting the masks. Setting the numa_node will
ensure that when cpu_cpu_mask() gets called, the correct node number is
used. This code movement helped fix the above call trace.
Reported-by: Geetika Moolchandani <Geetika.Moolchandani1@ibm.com>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210401154200.150077-1-srikar@linux.vnet.ibm.com
|
|
Define macros to list ppc interrupt types in interttupt.h, replace the
reference of the trap hex values with these macros.
Referred the hex numbers in arch/powerpc/kernel/exceptions-64e.S,
arch/powerpc/kernel/exceptions-64s.S, arch/powerpc/kernel/head_*.S,
arch/powerpc/kernel/head_booke.h and arch/powerpc/include/asm/kvm_asm.h.
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
[mpe: Resolve conflicts in nmi_disables_ftrace(), fix 40x build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1618398033-13025-1-git-send-email-sxwjean@me.com
|
|
A few archs like powerpc have different errno.h values for macros
EDEADLOCK and EDEADLK. In code including both libc and linux versions of
errno.h, this can result in multiple definitions of EDEADLOCK in the
include chain. Definitions to the same value (e.g. seen with mips) do
not raise warnings, but on powerpc there are redefinitions changing the
value, which raise warnings and errors (if using "-Werror").
Guard against these redefinitions to avoid build errors like the following,
first seen cross-compiling libbpf v5.8.9 for powerpc using GCC 8.4.0 with
musl 1.1.24:
In file included from ../../arch/powerpc/include/uapi/asm/errno.h:5,
from ../../include/linux/err.h:8,
from libbpf.c:29:
../../include/uapi/asm-generic/errno.h:40: error: "EDEADLOCK" redefined [-Werror]
#define EDEADLOCK EDEADLK
In file included from toolchain-powerpc_8540_gcc-8.4.0_musl/include/errno.h:10,
from libbpf.c:26:
toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/errno.h:58: note: this is the location of the previous definition
#define EDEADLOCK 58
cc1: all warnings being treated as errors
Cc: Stable <stable@vger.kernel.org>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200917135437.1238787-1-Tony.Ambardar@gmail.com
|
|
On systems with large CPUs per node, even with the filtered matching of
related CPUs, there can be large number of calls to cpu_to_chip_id for
the same CPU. For example with 4096 vCPU, 1 node QEMU configuration,
with 4 threads per core, system could be see upto 1024 calls to
cpu_to_chip_id() for the same CPU. On a given system, cpu_to_chip_id()
for a given CPU would always return the same. Hence cache the result in
a lookup table for use in subsequent calls.
Since all CPUs sharing the same core will belong to the same chip, the
lookup_table has an entry for one CPU per core. chip_id_lookup_table is
not being freed and would be used on subsequent CPU online post CPU
offline.
Reported-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210415120934.232271-4-srikar@linux.vnet.ibm.com
|
|
Now that cpu_core_mask has been reintroduced, lets revert
commit 4bce545903fa ("powerpc/topology: Update topology_core_cpumask")
Post this commit, lscpu should reflect topologies as requested by a user
when a QEMU instance is launched with NUMA spanning multiple sockets.
Reported-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210415120934.232271-3-srikar@linux.vnet.ibm.com
|
|
Daniel reported that with Commit 4ca234a9cbd7 ("powerpc/smp: Stop
updating cpu_core_mask") QEMU was unable to set single NUMA node SMP
topologies such as:
-smp 8,maxcpus=8,cores=2,threads=2,sockets=2
i.e he expected 2 sockets in one NUMA node.
The above commit helped to reduce boot time on Large Systems for
example 4096 vCPU single socket QEMU instance. PAPR is silent on
having more than one socket within a NUMA node.
cpu_core_mask and cpu_cpu_mask for any CPU would be same unless the
number of sockets is different from the number of NUMA nodes.
One option is to reintroduce cpu_core_mask but use a slightly
different method to arrive at the cpu_core_mask. Previously each CPU's
chip-id would be compared with all other CPU's chip-id to verify if
both the CPUs were related at the chip level. Now if a CPU 'A' is
found related / (unrelated) to another CPU 'B', all the thread
siblings of 'A' and thread siblings of 'B' are automatically marked as
related / (unrelated).
Also if a platform doesn't support ibm,chip-id property, i.e its
cpu_to_chip_id returns -1, cpu_core_map holds a copy of
cpu_cpu_mask().
Fixes: 4ca234a9cbd7 ("powerpc/smp: Stop updating cpu_core_mask")
Reported-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210415120934.232271-2-srikar@linux.vnet.ibm.com
|
|
The 'chip_id' field of the XIVE CPU structure is used to choose a
target for a source located on the same chip. For that, the XIVE
driver queries the chip identifier from the "ibm,chip-id" property
and compares it to a 'src_chip' field identifying the chip of a
source. This information is only available on the PowerNV platform,
'src_chip' being assigned to XIVE_INVALID_CHIP_ID under pSeries.
The "ibm,chip-id" property is also not available on all platforms. It
was first introduced on PowerNV and later, under QEMU for pSeries/KVM.
However, the property is not part of PAPR and does not exist under
pSeries/PowerVM.
Assign 'chip_id' to XIVE_INVALID_CHIP_ID by default and let the
PowerNV platform override the value with the "ibm,chip-id" property.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210413130352.1183267-1-clg@kaod.org
|
|
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
Fixes: 7340056567e3 ("powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210211182435.47968-1-tyreld@linux.ibm.com
|
|
When I changed the rc variable to be long rather than int64_t I
neglected to update the printk(), leading to a build break:
arch/powerpc/platforms/pseries/papr_scm.c: In function 'papr_scm_pmem_flush':
arch/powerpc/platforms/pseries/papr_scm.c:144:26: warning: format
'%lld' expects argument of type 'long long int', but argument 3 has
type 'long int' [-Wformat=]
Fixes: 75b7c05ebf90 ("powerpc/papr_scm: Implement support for H_SCM_FLUSH hcall")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210416111209.765444-2-mpe@ellerman.id.au
|
|
This is a pseries only driver, it should be built by default as part of
pseries_defconfig to get some build coverage.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210416111209.765444-1-mpe@ellerman.id.au
|
|
The lkp bot pointed out that with W=1 we get:
arch/powerpc/mm/book3s64/radix_pgtable.c:183:6: error: no previous
prototype for 'radix__change_memory_range'
Which is really saying that it could be static, make it so.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch adds the necessary glue to provide time namespaces.
Things are mainly copied from ARM64.
__arch_get_timens_vdso_data() calculates timens vdso data position
based on the vdso data position, knowing it is the next page in vvar.
This avoids having to redo the mflr/bcl/mflr/mtlr dance to locate
the page relative to running code position.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> # vDSO parts
Acked-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1a15495f80ec19a87b16cf874dbf7c3fa5ec40fe.1617209142.git.christophe.leroy@csgroup.eu
|
|
Since commit 511157ab641e ("powerpc/vdso: Move vdso datapage up front")
VVAR page is in front of the VDSO area. In result it breaks CRIU
(Checkpoint Restore In Userspace) [1], where CRIU expects that "[vdso]"
from /proc/../maps points at ELF/vdso image, rather than at VVAR data page.
Laurent made a patch to keep CRIU working (by reading aux vector).
But I think it still makes sence to separate two mappings into different
VMAs. It will also make ppc64 less "special" for userspace and as
a side-bonus will make VVAR page un-writable by debugger (which previously
would COW page and can be unexpected).
I opportunistically Cc stable on it: I understand that usually such
stuff isn't a stable material, but that will allow us in CRIU have
one workaround less that is needed just for one release (v5.11) on
one platform (ppc64), which we otherwise have to maintain.
I wouldn't go as far as to say that the commit 511157ab641e is ABI
regression as no other userspace got broken, but I'd really appreciate
if it gets backported to v5.11 after v5.12 is released, so as not
to complicate already non-simple CRIU-vdso code. Thanks!
[1]: https://github.com/checkpoint-restore/criu/issues/1417
Cc: stable@vger.kernel.org # v5.11
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> # vDSO parts.
Acked-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f401eb1ebc0bfc4d8f0e10dc8e525fd409eb68e2.1617209142.git.christophe.leroy@csgroup.eu
|
|
For the same reason as commit e876f0b69dc9 ("lib/vdso: Allow
architectures to provide the vdso data pointer"), powerpc wants to
avoid calculation of relative position to code.
As the timens_vdso_data is next page to vdso_data, provide
vdso_data pointer to __arch_get_timens_vdso_data() in order
to ease the calculation on powerpc in following patches.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/539c4204b1baa77c55f758904a1ea239abbc7a5c.1617209142.git.christophe.leroy@csgroup.eu
|
