Age | Commit message (Collapse) | Author |
|
Architectures like powerpc use different address range to map ioremap
and vmalloc range. The memunmap() check used by the nvdimm layer was
wrongly using is_vmalloc_addr() to check for ioremap range which fails
for ppc64. This result in ppc64 not freeing the ioremap mapping. The
side effect of this is an unbind failure during module unload with
papr_scm nvdimm driver
Link: http://lkml.kernel.org/r/20190701134038.14165-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Fixes: b5beae5e224f ("powerpc/pseries: Add driver for PAPR SCM regions")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from
the dma-mapping interface for ARM
- Convert the generic MMC DT doc to YAML schemas
- Drop questionable support for powered-on re-init of SDIO cards at
runtime resume and for SDIO HW reset
- Prevent questionable re-init of powered-on removable SDIO cards at
system resume
- Cleanup and clarify some SDIO core code
MMC host:
- tmio: Make runtime PM enablement more flexible for variants
- tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt
to clarify
- sdhci-pci: Add support for Intel EHL
- sdhci-pci-o2micro: Enable support for 8-bit bus
- sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
- sdhci-of-esdhc: Improve clock management and tuning
- sdhci_am654: Enable support for 4 and 8-bit bus on J721E
- sdhci-sprd: Use pinctrl for a proper signal voltage switch
- sdhci-sprd: Add support for HS400 enhanced strobe mode
- sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the
clock
- sdhci-sprd: Add support for optional gate clock
- sunxi-mmc: Convert DT doc to YAML schemas
- meson-gx: Add support for broken DRAM access for DMA
MEMSTICK core:
- Fixup error path of memstick_init()"
* tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
mmc: alcor: remove a redundant greater or equal to zero comparison
mmc: sdhci-msm: fix mutex while in spinlock
mmc: sdhci_am654: Make some symbols static
dma-mapping: remove dma_max_pfn
mmc: core: let the dma map ops handle bouncing
dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
mmc: sdhci-sprd: Add pin control support for voltage switch
dt-bindings: mmc: sprd: Add pinctrl support
mmc: sdhci-sprd: Add start_signal_voltage_switch ops
mmc: sdhci-pci: Add support for Intel EHL
mmc: tmio: Use dma_max_mapping_size() instead of a workaround
mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
mmc: sdio: Turn sdio_run_irqs() into static
mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "large" TTY and Serial driver update for 5.3-rc1.
It's in the negative number of lines overall as we removed an obsolete
serial driver that was causing problems for some people who were
trying to clean up some apis (the mpsc.c driver, which only worked for
some pre-production hardware that no one has anymore.)
Other than that, lots of tiny changes, cleaning up small things along
with some platform-specific serial driver updates.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (68 commits)
tty: serial: fsl_lpuart: add imx8qxp support
serial: imx: set_termios(): preserve RTS state
serial: imx: set_termios(): clarify RTS/CTS bits calculation
serial: imx: set_termios(): factor-out 'ucr2' initial value
serial: sh-sci: Terminate TX DMA during buffer flushing
serial: sh-sci: Fix TX DMA buffer flushing and workqueue races
serial: mpsc: Remove obsolete MPSC driver
serial: 8250: 8250_core: Fix missing unlock on error in serial8250_register_8250_port()
serial: stm32: add RX and TX FIFO flush
serial: stm32: add support of RX FIFO threshold
serial: stm32: add support of TX FIFO threshold
serial: stm32: update PIO transmission
serial: stm32: add support of timeout interrupt for RX
Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"
tty/serial/8250: use mctrl_gpio helpers
serial: mctrl_gpio: Check if GPIO property exisits before requesting it
serial: 8250: pericom_do_set_divisor can be static
tty: serial_core: Set port active bit in uart_port_activate
serial: 8250: Add MSR/MCR TIOCM conversion wrapper functions
serial: 8250: factor out serial8250_{set,clear}_THRI() helpers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the "large" pull request for char and misc and other assorted
smaller driver subsystems for 5.3-rc1.
It seems that this tree is becoming the funnel point of lots of
smaller driver subsystems, which is fine for me, but that's why it is
getting larger over time and does not just contain stuff under
drivers/char/ and drivers/misc.
Lots of small updates all over the place here from different driver
subsystems:
- habana driver updates
- coresight driver updates
- documentation file movements and updates
- Android binder fixes and updates
- extcon driver updates
- google firmware driver updates
- fsi driver updates
- smaller misc and char driver updates
- soundwire driver updates
- nvmem driver updates
- w1 driver fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (188 commits)
coresight: Do not default to CPU0 for missing CPU phandle
dt-bindings: coresight: Change CPU phandle to required property
ocxl: Allow contexts to be attached with a NULL mm
fsi: sbefifo: Don't fail operations when in SBE IPL state
coresight: tmc: Smatch: Fix potential NULL pointer dereference
coresight: etm3x: Smatch: Fix potential NULL pointer dereference
coresight: Potential uninitialized variable in probe()
coresight: etb10: Do not call smp_processor_id from preemptible
coresight: tmc-etf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: alloc_perf_buf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: Do not call smp_processor_id() from preemptible
docs: misc-devices: convert files without extension to ReST
fpga: dfl: fme: align PR buffer size per PR datawidth
fpga: dfl: fme: remove copy_to_user() in ioctl for PR
fpga: dfl-fme-mgr: fix FME_PR_INTFC_ID register address.
intel_th: msu: Start read iterator from a non-empty window
intel_th: msu: Split sgt array and pointer in multiwindow mode
intel_th: msu: Support multipage blocks
intel_th: pci: Add Ice Lake NNPI support
intel_th: msu: Fix single mode with disabled IOMMU
...
|
|
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A collection of assorted fixes:
- Fix for the pinned cr0/4 fallout which escaped all testing efforts
because the kvm-intel module was never loaded when the kernel was
compiled with CONFIG_PARAVIRT=n. The cr0/4 accessors are moved out
of line and static key is now solely used in the core code and
therefore can stay in the RO after init section. So the kvm-intel
and other modules do not longer reference the (read only) static
key which the module loader tried to update.
- Prevent an infinite loop in arch_stack_walk_user() by breaking out
of the loop once the return address is detected to be 0.
- Prevent the int3_emulate_call() selftest from corrupting the stack
when KASAN is enabled. KASASN clobbers more registers than covered
by the emulated call implementation. Convert the int3_magic()
selftest to a ASM function so the compiler cannot KASANify it.
- Unbreak the build with old GCC versions and with the Gold linker by
reverting the 'Move of _etext to the actual end of .text'. In both
cases the build fails with 'Invalid absolute R_X86_64_32S
relocation: _etext'
- Initialize the context lock for init_mm, which was never an issue
until the alternatives code started to use a temporary mm for
patching.
- Fix a build warning vs. the LOWMEM_PAGES constant where clang
complains rightfully about a signed integer overflow in the shift
operation by converting the operand to an ULL.
- Adjust the misnamed ENDPROC() of common_spurious in the 32bit entry
code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/stacktrace: Prevent infinite loop in arch_stack_walk_user()
x86/asm: Move native_write_cr0/4() out of line
x86/pgtable/32: Fix LOWMEM_PAGES constant
x86/alternatives: Fix int3_emulate_call() selftest stack corruption
x86/entry/32: Fix ENDPROC of common_spurious
Revert "x86/build: Move _etext to actual end of .text"
x86/ldt: Initialize the context lock for init_mm
|
|
When current task is interrupted in-between stack frame allocation
and backchain write instructions new stack frame backchain pointer
is left uninitialized. That invalid backchain value is passed into
outside_of_stack for sanity check. Make sure int overflow does not happen
by subtracting stack_frame size from the stack "end" rather than adding
it to "random" backchain value.
Fixes: 41b0474c1b1c ("s390/unwind: introduce stack unwind API")
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Provide an attribute to query the usage of mio instructions.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Move enablement of mio addressing control from detect_machine_facilities
to pci_base_init. detect_machine_facilities runs so early that the
static branches have not been toggled yet, thus mio addressing control
was always off. In pci_base_init we have to use the SMP aware
ctl_set_bit though.
Fixes: 833b441ec0f6 ("s390: enable processes for mio instructions")
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use the correct bit for detection of the machine capability associated
with the has_secure attribute. It is expected that the underlying
platform (including hypervisors) unsets the bit when they don't provide
secure ipl for their guests.
Fixes: c9896acc7851 ("s390/ipl: Provide has_secure sysfs attribute")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add the extended counter set definitions for s390 machine types
8561 and 8262. They are identical with machine types 3906 and
3907.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Userspace tools might have the need to release space for Extent Space
Efficient (ESE) volumes when working with such a device.
Provide the necessarry interface for such a task by implementing a new
ioctl BIODASDRAS. The ioctl uses the format_data_t data structure for
data input:
typedef struct format_data_t {
unsigned int start_unit; /* from track */
unsigned int stop_unit; /* to track */
unsigned int blksize; /* sectorsize */
unsigned int intensity;
} format_data_t;
If the intensity is set to 0x40, start_unit and stop_unit are ignored
and space for the entire volume is released. Otherwise, if intensity is
set to 0, the respective range is released (if possible).
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The definition for the bit that removes the write permission for record
zero when formatting was missing. Add it to complete the list.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull clone3 system call from Christian Brauner:
"This adds the clone3 syscall which is an extensible successor to clone
after we snagged the last flag with CLONE_PIDFD during the 5.2 merge
window for clone(). It cleanly supports all of the flags from clone()
and thus all legacy workloads.
There are few user visible differences between clone3 and clone.
First, CLONE_DETACHED will cause EINVAL with clone3 so we can reuse
this flag. Second, the CSIGNAL flag is deprecated and will cause
EINVAL to be reported. It is superseeded by a dedicated "exit_signal"
argument in struct clone_args thus freeing up even more flags. And
third, clone3 gives CLONE_PIDFD a dedicated return argument in struct
clone_args instead of abusing CLONE_PARENT_SETTID's parent_tidptr
argument.
The clone3 uapi is designed to be easy to handle on 32- and 64 bit:
/* uapi */
struct clone_args {
__aligned_u64 flags;
__aligned_u64 pidfd;
__aligned_u64 child_tid;
__aligned_u64 parent_tid;
__aligned_u64 exit_signal;
__aligned_u64 stack;
__aligned_u64 stack_size;
__aligned_u64 tls;
};
and a separate kernel struct is used that uses proper kernel typing:
/* kernel internal */
struct kernel_clone_args {
u64 flags;
int __user *pidfd;
int __user *child_tid;
int __user *parent_tid;
int exit_signal;
unsigned long stack;
unsigned long stack_size;
unsigned long tls;
};
The system call comes with a size argument which enables the kernel to
detect what version of clone_args userspace is passing in. clone3
validates that any additional bytes a given kernel does not know about
are set to zero and that the size never exceeds a page.
A nice feature is that this patchset allowed us to cleanup and
simplify various core kernel codepaths in kernel/fork.c by making the
internal _do_fork() function take struct kernel_clone_args even for
legacy clone().
This patch also unblocks the time namespace patchset which wants to
introduce a new CLONE_TIMENS flag.
Note, that clone3 has only been wired up for x86{_32,64}, arm{64}, and
xtensa. These were the architectures that did not require special
massaging.
Other architectures treat fork-like system calls individually and
after some back and forth neither Arnd nor I felt confident that we
dared to add clone3 unconditionally to all architectures. We agreed to
leave this up to individual architecture maintainers. This is why
there's an additional patch that introduces __ARCH_WANT_SYS_CLONE3
which any architecture can set once it has implemented support for
clone3. The patch also adds a cond_syscall(clone3) for architectures
such as nios2 or h8300 that generate their syscall table by simply
including asm-generic/unistd.h. The hope is to get rid of
__ARCH_WANT_SYS_CLONE3 and cond_syscall() rather soon"
* tag 'clone3-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
arch: handle arches who do not yet define clone3
arch: wire-up clone3() syscall
fork: add clone3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for 5.3
- Add support for chained PMU counters in guests
- Improve SError handling
- Handle Neoverse N1 erratum #1349291
- Allow side-channel mitigation status to be migrated
- Standardise most AArch64 system register accesses to msr_s/mrs_s
- Fix host MPIDR corruption on 32bit
|
|
On VMX, KVM currently does not re-enable irqs until after it has exited
the guest context. As a result, a tick that fires in the window between
VM-Exit and guest_exit_irqoff() will be accounted as system time. While
said window is relatively small, it's large enough to be problematic in
some configurations, e.g. if VM-Exits are consistently occurring a hair
earlier than the tick irq.
Intentionally toggle irqs back off so that guest_exit_irqoff() can be
used in lieu of guest_exit() in order to avoid the save/restore of flags
in guest_exit(). On my Haswell system, "nop; cli; sti" is ~6 cycles,
versus ~28 cycles for "pushf; pop <reg>; cli; push <reg>; popf".
Fixes: f2485b3e0c6c0 ("KVM: x86: use guest_exit_irqoff")
Reported-by: Wei Yang <w90p710@gmail.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Some events can provide a guest with information about other guests or the
host (e.g. L3 cache stats); providing the capability to restrict access
to a "safe" set of events would limit the potential for the PMU to be used
in any side channel attacks. This change introduces a new VM ioctl that
sets an event filter. If the guest attempts to program a counter for
any blacklisted or non-whitelisted event, the kernel counter won't be
created, so any RDPMC/RDMSR will show 0 instances of that event.
Signed-off-by: Eric Hankland <ehankland@google.com>
[Lots of changes. All remaining bugs are probably mine. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
arch_stack_walk_user() checks `if (fp == frame.next_fp)` to prevent a
infinite loop by self reference but it's not enogh for circular reference.
Once a lack of return address is found, there is no point to continue the
loop, so break out.
Fixes: 02b67518e2b1 ("tracing: add support for userspace stacktraces in tracing/iter_ctrl")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20190711023501.963-1-devel@etsukata.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"This adds two main features.
- First, it adds polling support for pidfds. This allows process
managers to know when a (non-parent) process dies in a race-free
way.
The notification mechanism used follows the same logic that is
currently used when the parent of a task is notified of a child's
death. With this patchset it is possible to put pidfds in an
{e}poll loop and get reliable notifications for process (i.e.
thread-group) exit.
- The second feature compliments the first one by making it possible
to retrieve pollable pidfds for processes that were not created
using CLONE_PIDFD.
A lot of processes get created with traditional PID-based calls
such as fork() or clone() (without CLONE_PIDFD). For these
processes a caller can currently not create a pollable pidfd. This
is a problem for Android's low memory killer (LMK) and service
managers such as systemd.
Both patchsets are accompanied by selftests.
It's perhaps worth noting that the work done so far and the work done
in this branch for pidfd_open() and polling support do already see
some adoption:
- Android is in the process of backporting this work to all their LTS
kernels [1]
- Service managers make use of pidfd_send_signal but will need to
wait until we enable waiting on pidfds for full adoption.
- And projects I maintain make use of both pidfd_send_signal and
CLONE_PIDFD [2] and will use polling support and pidfd_open() too"
[1] https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.9+backport%22
https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.14+backport%22
https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.19+backport%22
[2] https://github.com/lxc/lxc/blob/aab6e3eb73c343231cdde775db938994fc6f2803/src/lxc/start.c#L1753
* tag 'pidfd-updates-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
tests: add pidfd_open() tests
arch: wire-up pidfd_open()
pid: add pidfd_open()
pidfd: add polling selftests
pidfd: add polling support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fix from Geert Uytterhoeven:
"Don't select ARCH_HAS_DMA_PREP_COHERENT for nommu or coldfire.
This is a fix for an issue detected in next, to avoid introducing
build failures when merging Christoph's dma-mapping tree later"
* tag 'm68k-for-v5.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Don't select ARCH_HAS_DMA_PREP_COHERENT for nommu or coldfire
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68nommu updates from Greg Ungerer:
"A series of cleanups for the FLAT format binary loader, binfmt_flat,
from Christoph.
The end goal is to support no-MMU on RISC-V, and the last patch
enables that"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
riscv: add binfmt_flat support
binfmt_flat: don't offset the data start
binfmt_flat: move the MAX_SHARED_LIBS definition to binfmt_flat.c
binfmt_flat: remove the persistent argument from flat_get_addr_from_rp
binfmt_flat: provide an asm-generic/flat.h
binfmt_flat: make support for old format binaries optional
binfmt_flat: add a ARCH_HAS_BINFMT_FLAT option
binfmt_flat: add endianess annotations
binfmt_flat: use fixed size type for the on-disk format
binfmt_flat: consolidate two version of flat_v2_reloc_t
binfmt_flat: remove the unused OLD_FLAT_FLAG_RAM definition
binfmt_flat: remove the uapi <linux/flat.h> header
binfmt_flat: replace flat_argvp_envp_on_stack with a Kconfig variable
binfmt_flat: remove flat_old_ram_flag
binfmt_flat: provide a default version of flat_get_relocate_addr
binfmt_flat: remove flat_set_persistent
binfmt_flat: remove flat_reloc_valid
|
|
The pinning of sensitive CR0 and CR4 bits caused a boot crash when loading
the kvm_intel module on a kernel compiled with CONFIG_PARAVIRT=n.
The reason is that the static key which controls the pinning is marked RO
after init. The kvm_intel module contains a CR4 write which requires to
update the static key entry list. That obviously does not work when the key
is in a RO section.
With CONFIG_PARAVIRT enabled this does not happen because the CR4 write
uses the paravirt indirection and the actual write function is built in.
As the key is intended to be immutable after init, move
native_write_cr0/4() out of line.
While at it consolidate the update of the cr4 shadow variable and store the
value right away when the pinning is initialized on a booting CPU. No point
in reading it back 20 instructions later. This allows to confine the static
key and the pinning variable to cpu/common and allows to mark them static.
Fixes: 8dbec27a242c ("x86/asm: Pin sensitive CR0 bits")
Fixes: 873d50d58f67 ("x86/asm: Pin sensitive CR4 bits")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Xi Ruoyao <xry111@mengyan1223.wang>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Xi Ruoyao <xry111@mengyan1223.wang>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907102140340.1758@nanos.tec.linutronix.de
|
|
clang points out that the computation of LOWMEM_PAGES causes a signed
integer overflow on 32-bit x86:
arch/x86/kernel/head32.c:83:20: error: signed shift result (0x100000000) requires 34 bits to represent, but 'int' only has 32 bits [-Werror,-Wshift-overflow]
(PAGE_TABLE_SIZE(LOWMEM_PAGES) << PAGE_SHIFT);
^~~~~~~~~~~~
arch/x86/include/asm/pgtable_32.h:109:27: note: expanded from macro 'LOWMEM_PAGES'
#define LOWMEM_PAGES ((((2<<31) - __PAGE_OFFSET) >> PAGE_SHIFT))
~^ ~~
arch/x86/include/asm/pgtable_32.h:98:34: note: expanded from macro 'PAGE_TABLE_SIZE'
#define PAGE_TABLE_SIZE(pages) ((pages) / PTRS_PER_PGD)
Use the _ULL() macro to make it a 64-bit constant.
Fixes: 1e620f9b23e5 ("x86/boot/32: Convert the 32-bit pgtable setup code from assembly to C")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190710130522.1802800-1-arnd@arndb.de
|
|
Replace $(src) and $(obj) with $(srctree) and $(objtree), respectively.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
We get a warning when build kernel W=1:
arch/x86/kvm/../../../virt/kvm/eventfd.c:48:1: warning: no previous prototype for ‘kvm_arch_irqfd_allowed’ [-Wmissing-prototypes]
kvm_arch_irqfd_allowed(struct kvm *kvm, struct kvm_irqfd *args)
^
The reason is kvm_arch_irqfd_allowed() is declared in arch/x86/kvm/irq.h,
which is not included by eventfd.c. Considering kvm_arch_irqfd_allowed()
is a weakly defined function in eventfd.c, remove the declaration to
kvm_host.h can fix this.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These days, the DMA mapping code must bounce buffers for any unsupported
address. If the driver needs to optimize for natively supported ranges,
then it should use dma_get_required_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
KASAN shows the following splat during boot:
BUG: KASAN: unknown-crash in unwind_next_frame+0x3f6/0x490
Read of size 8 at addr ffffffff84007db0 by task swapper/0
CPU: 0 PID: 0 Comm: swapper Tainted: G T 5.2.0-rc6-00013-g7457c0d #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
dump_stack+0x19/0x1b
print_address_description+0x1b0/0x2b2
__kasan_report+0x10f/0x171
kasan_report+0x12/0x1c
__asan_load8+0x54/0x81
unwind_next_frame+0x3f6/0x490
unwind_next_frame+0x1b/0x23
arch_stack_walk+0x68/0xa5
stack_trace_save+0x7b/0xa0
save_trace+0x3c/0x93
mark_lock+0x1ef/0x9b1
lock_acquire+0x122/0x221
__mutex_lock+0xb6/0x731
mutex_lock_nested+0x16/0x18
_vm_unmap_aliases+0x141/0x183
vm_unmap_aliases+0x14/0x16
change_page_attr_set_clr+0x15e/0x2f2
set_memory_4k+0x2a/0x2c
check_bugs+0x11fd/0x1298
start_kernel+0x793/0x7eb
x86_64_start_reservations+0x55/0x76
x86_64_start_kernel+0x87/0xaa
secondary_startup_64+0xa4/0xb0
Memory state around the buggy address:
ffffffff84007c80: 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1
ffffffff84007d00: f1 00 00 00 00 00 00 00 00 00 f2 f2 f2 f3 f3 f3
>ffffffff84007d80: f3 79 be 52 49 79 be 00 00 00 00 00 00 00 00 f1
It turns out that int3_selftest() is corrupting the stack. The problem is
that the KASAN-ified version of int3_magic() is much less trivial than the
C code appears. It clobbers several unexpected registers. So when the
selftest's INT3 is converted to an emulated call to int3_magic(), the
registers are clobbered and Bad Things happen when the function returns.
Fix this by converting int3_magic() to the trivial ASM function it should
be, avoiding all calling convention issues. Also add ASM_CALL_CONSTRAINT to
the INT3 ASM, since it contains a 'CALL'.
[peterz: cribbed changelog from josh]
Fixes: 7457c0da024b ("x86/alternatives: Add int3_emulate_call() selftest")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Debugged-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/20190709125744.GB3402@hirez.programming.kicks-ass.net
|
|
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Dynamic ftrace support by Sven Schnelle and a header guard fix by
Denis Efremov"
* 'parisc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: asm: psw.h: missing header guard
parisc: add dynamic ftrace
compiler.h: add CC_USING_PATCHABLE_FUNCTION_ENTRY
parisc: use pr_debug() in kernel/module.c
parisc: add WARN_ON() to clear_fixmap
parisc: add spinlock to patch function
parisc: add support for patching multiple words
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x865 kdump updates from Thomas Gleixner:
"Yet more kexec/kdump updates:
- Properly support kexec when AMD's memory encryption (SME) is
enabled
- Pass reserved e820 ranges to the kexec kernel so both PCI and SME
can work"
* 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/proc/vmcore: Enable dumping of encrypted memory when SEV was active
x86/kexec: Set the C-bit in the identity map page table when SEV is active
x86/kexec: Do not map kexec area as decrypted when SEV is active
x86/crash: Add e820 reserved ranges to kdump kernel's e820 table
x86/mm: Rework ioremap resource mapping determination
x86/e820, ioport: Add a new I/O resource descriptor IORES_DESC_RESERVED
x86/mm: Create a workarea in the kernel for SME early encryption
x86/mm: Identify the end of the kernel area to be reserved
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 boot updates from Thomas Gleixner:
"Assorted updates to kexec/kdump:
- Proper kexec support for 4/5-level paging and jumping from a
5-level to a 4-level paging kernel.
- Make the EFI support for kexec/kdump more robust
- Enforce that the GDT is properly aligned instead of getting the
alignment by chance"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kdump/64: Restrict kdump kernel reservation to <64TB
x86/kexec/64: Prevent kexec from 5-level paging to a 4-level only kernel
x86/boot: Add xloadflags bits to check for 5-level paging support
x86/boot: Make the GDT 8-byte aligned
x86/kexec: Add the ACPI NVS region to the ident map
x86/boot: Call get_rsdp_addr() after console_init()
Revert "x86/boot: Disable RSDP parsing temporarily"
x86/boot: Use efi_setup_data for searching RSDP on kexec-ed kernels
x86/kexec: Add the EFI system tables and ACPI tables to the ident map
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"The main changes in this cycle on the kernel side were:
- CPU PMU and uncore driver updates to Intel Snow Ridge, IceLake,
KabyLake, AmberLake and WhiskeyLake CPUs.
- Rework the MSR probing infrastructure to make it more robust, make
it work better on virtualized systems and to better expose it on
sysfs.
- Rework PMU attributes group support based on the feedback from
Greg. The core sysfs patch that adds sysfs_update_groups() was
acked by Greg.
There's a lot of perf tooling changes as well, all around the place:
- vendor updates to Intel, cs-etm (ARM), ARM64, s390,
- various enhancements to Intel PT tooling support:
- Improve CBR (Core to Bus Ratio) packets support.
- Export power and ptwrite events to sqlite and postgresql.
- Add support for decoding PEBS via PT packets.
- Add support for samples to contain IPC ratio, collecting cycles
information from CYC packets, showing the IPC info periodically
- Allow using time ranges
- lots of updates to perf pmu, perf stat, perf trace, eBPF support,
perf record, perf diff, etc. - please see the shortlog and Git log
for details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (252 commits)
tools arch x86: Sync asm/cpufeatures.h with the with the kernel
tools build: Check if gettid() is available before providing helper
perf jvmti: Address gcc string overflow warning for strncpy()
perf python: Remove -fstack-protector-strong if clang doesn't have it
perf annotate TUI browser: Do not use member from variable within its own initialization
perf tests: Fix record+probe_libc_inet_pton.sh for powerpc64
perf evsel: Do not rely on errno values for precise_ip fallback
perf thread: Allow references to thread objects after machine__exit()
perf header: Assign proper ff->ph in perf_event__synthesize_features()
tools arch kvm: Sync kvm headers with the kernel sources
perf script: Allow specifying the files to process guest samples
perf tools metric: Don't include duration_time in group
perf list: Avoid extra : for --raw metrics
perf vendor events intel: Metric fixes for SKX/CLX
perf tools: Fix typos / broken sentences
perf jevents: Add support for Hisi hip08 L3C PMU aliasing
perf jevents: Add support for Hisi hip08 HHA PMU aliasing
perf jevents: Add support for Hisi hip08 DDRC PMU aliasing
perf pmu: Support more complex PMU event aliasing
perf diff: Documentation -c cycles option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update PCI and ACPI power management (improved handling of ACPI
power resources and PCIe link delays, fixes related to corner cases,
hibernation handling rework), fix and extend the operating performance
points (OPP) framework, add new cpufreq drivers for Raspberry Pi and
imx8m chips, update some other cpufreq drivers, clean up assorted
pieces of PM code and documentation and update tools.
Specifics:
- Improve the handling of shared ACPI power resources in the PCI bus
type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec into
account as appropriate and avoid polling devices in D3cold for PME
(Mika Westerberg).
- Fix some corner case issues in ACPI device power management and in
the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210, and
armada-37xx cpufreq drivers (David Arcari, Florian Fainelli, Paweł
Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black)"
* tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (57 commits)
ACPI: PM: Make acpi_sleep_state_supported() non-static
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Unexport acpi_device_get_power()
Documentation: ABI: power: Add missing newline at end of file
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
cpufreq: Don't skip frequency validation for has_target() drivers
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
cpufreq: Use has_target() instead of !setpolicy
...
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
- remove fbdev notifier usage for fbcon (as prep work to clean up the
fbcon locking), add locking checks in vt/console code and make
assorted cleanups in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb,
pvr2fb and pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph
Hellwig)
- add check for new BGRT status field rotation bits in efifb driver
(Hans de Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R.
Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio
Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
* tag 'fbdev-v5.3' of git://github.com/bzolnier/linux: (62 commits)
video: fbdev: imxfb: fix a typo in imxfb_probe()
video: fbdev: s3c-fb: Mark expected switch fall-throughs
video: fbdev: s3c-fb: fix sparse warnings about using incorrect types
video: fbdev: don't print error message on framebuffer_alloc() failure
video: fbdev: intelfb: return -ENOMEM on framebuffer_alloc() failure
video: fbdev: s3c-fb: return -ENOMEM on framebuffer_alloc() failure
vga_switcheroo: Depend upon fbcon being built-in, if enabled
video: fbdev: omap2: remove rfbi
video: fbdev: atmel_lcdfb: remove redundant initialization to variable ret
video: fbdev-MMP: Use struct_size() in devm_kzalloc()
video: fbdev: controlfb: fix warnings about comparing pointer to 0
efifb: BGRT: Add check for new BGRT status field rotation bits
jz4740_fb: fix DMA API abuse
video: fbdev: pvr2fb: fix link error for pvr2fb_pci_exit
video: fbdev: s3c-fb: add COMPILE_TEST support
video: fbdev: imxfb: fix sparse warnings about using incorrect types
video: fbdev: pvr2fb: fix build warning when compiling as module
fbcon: Export fbcon_update_vcs
backlight: simplify lcd notifier
staging/olpc_dcon: Add drm conversion to TODO
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Tony Luck:
"All the bits that Boris had queued in his tree plus four patches to
add support for Intel Icelake Xeon and then fix a few corner cases"
* tag 'please-pull-for_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC: Fix global-out-of-bounds write when setting edac_mc_poll_msec
EDAC, skx, i10nm: Fix source ID register offset
EDAC, i10nm: Check ECC enabling status per channel
EDAC, i10nm: Add Intel additional Ice-Lake support
EDAC: Make edac_debugfs_create_x*() return void
EDAC/aspeed: Remove set but not used variable 'np'
EDAC/ie31200: Reformat PCI device table
EDAC/ie31200: Add Intel Coffee Lake CPU support
EDAC/sifive: Add EDAC platform driver for SiFive SoCs
EDAC/sb_edac: Remove redundant update of tad_base
arm64: dts: stratix10: Add SDMMC EDAC node
EDAC/altera: Add Stratix10 SDMMC support
arm64: dts: stratix10: Add OCRAM EDAC node
EDAC/altera: Add Stratix10 OCRAM ECC support
EDAC/sysfs: Drop device references properly
EDAC/sysfs: Fix memory leak when creating a csrow object
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Make the dma-iommu code more generic so that it can be used outside
of the ARM context with other IOMMU drivers. Goal is to make use of
it on x86 too.
- Generic IOMMU domain support for the Intel VT-d driver. This driver
now makes more use of common IOMMU code to allocate default domains
for the devices it handles.
- An IOMMU fault reporting API to userspace. With that the IOMMU fault
handling can be done in user-space, for example to forward the faults
to a VM.
- Better handling for reserved regions requested by the firmware. These
can be 'relaxed' now, meaning that those don't prevent a device being
attached to a VM.
- Suspend/Resume support for the Renesas IOMMU driver.
- Added support for dumping SVA related fields of the DMAR table in the
Intel VT-d driver via debugfs.
- A pile of smaller fixes and cleanups.
* tag 'iommu-updates-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (90 commits)
iommu/omap: No need to check return value of debugfs_create functions
iommu/arm-smmu-v3: Invalidate ATC when detaching a device
iommu/arm-smmu-v3: Fix compilation when CONFIG_CMA=n
iommu/vt-d: Cleanup unused variable
iommu/amd: Flush not present cache in iommu_map_page
iommu/amd: Only free resources once on init error
iommu/amd: Move gart fallback to amd_iommu_init
iommu/amd: Make iommu_disable safer
iommu/io-pgtable: Support non-coherent page tables
iommu/io-pgtable: Replace IO_PGTABLE_QUIRK_NO_DMA with specific flag
iommu/io-pgtable-arm: Add support to use system cache
iommu/arm-smmu-v3: Increase maximum size of queues
iommu/vt-d: Silence a variable set but not used
iommu/vt-d: Remove an unused variable "length"
iommu: Fix integer truncation
iommu: Add padding to struct iommu_fault
iommu/vt-d: Consolidate domain_init() to avoid duplication
iommu/vt-d: Cleanup after delegating DMA domain to generic iommu
iommu/vt-d: Fix suspicious RCU usage in probe_acpi_namespace_devices()
iommu/vt-d: Allow DMA domain attaching to rmrr locked device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A couple of new features in the core, the most interesting one being
support for complex regulator coupling configurations initially
targeted at nVidia Tegra SoCs, and some new drivers but otherwise
quite a quiet release.
Summary:
- Core support for gradual ramping of voltages for devices that can't
manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster"
* tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: max77650: use vsel_step
regulator: implement selector stepping
regulator: max77650: add MODULE_ALIAS()
regulator: max77620: remove redundant assignment to variable ret
dt-bindings: regulator: add support for the stm32-booster
regulator: add support for the stm32-booster
regulator: s2mps11: Adjust supported buck voltages to real values
regulator: s2mps11: Fix buck7 and buck8 wrong voltages
gpio: Fix return value mismatch of function gpiod_get_from_of_node()
regulator: core: Expose some of core functions needed by couplers
regulator: core: Introduce API for regulators coupling customization
regulator: s2mps11: Add support for disabling S2MPS11 regulators in suspend
regulator: s2mps11: Reduce number of rdev_get_id() calls
regulator: qcom_spmi: Do NULL check for lvs
regulator: qcom_spmi: Fix math of spmi_regulator_set_voltage_time_sel
regulator: da9061/62: Adjust LDO voltage selection minimum value
regulator: s2mps11: Fix ERR_PTR dereference on GPIO lookup failure
regulator: qcom_spmi: add PMS405 SPMI regulator
dt-bindings: qcom_spmi: Document pms405 support
arm64: dts: msm8998-mtp: Add pm8005_s1 regulator
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the big slew of GPIO changes for the v5.3 kernel cycle. This
is mostly incremental work this time.
Three important things:
- The FMC subsystem is deleted through my tree. This happens through
GPIO as its demise was discussed in relation to a patch decoupling
its GPIO implementation from the standard way of handling GPIO. As
it turns out, that is not the only subsystem it reimplements and
the authors think it is better do scratch it and start over using
the proper kernel subsystems than try to polish the rust shiny. See
the commit (ACKed by the maintainers) for details.
- Arnd made a small devres patch that was ACKed by Greg and goes into
the device core.
- SPDX header change colissions may happen, because at times I've
seen that quite a lot changed during the -rc:s in regards to SPDX.
(It is good stuff, tglx has me convinced, and it is worth the
occasional pain.)
Apart from this is is nothing controversial or problematic.
Summary:
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer flags.
This makes a lot of sense, but took some time before I figured out
that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell King.
- Starting to move some drivers to the new API passing irq_chip along
with the gpio_chip when adding the gpio_chip instead of adding it
separately.
Unrelated:
- Delete the FMC subsystem"
* tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: tegra: Clean-up debugfs initialisation"
gpiolib: Use spinlock_t instead of struct spinlock
gpio: stp-xway: allow compile-testing
gpio: stp-xway: get rid of the #include <lantiq_soc.h> dependency
gpio: stp-xway: improve module clock error handling
gpio: stp-xway: simplify error handling in xway_stp_probe()
gpiolib: Clarify use of non-sleeping functions
gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants
gpiolib: Document new gpio_chip.init_valid_mask field
Documentation: gpio: Fix reference to gpiod_get_array()
gpio: pl061: drop duplicate printing of device name
gpio: altera: Pass irqchip when adding gpiochip
gpio: siox: Use devm_ managed gpiochip
gpio: siox: Add struct device *dev helper variable
gpio: siox: Pass irqchip when adding gpiochip
drivers: gpio: amd-fch: make resource struct const
devres: allow const resource arguments
gpio: ath79: Pass irqchip when adding gpiochip
gpio: tegra: Clean-up debugfs initialisation
gpio: siox: Switch to IRQ_TYPE_NONE
...
|
|
common_spurious is currently ENDed erroneously. common_interrupt is used
in its ENDPROC. So fix this mistake.
Found by my asm macros rewrite patchset.
Fixes: f8a8fe61fec8 ("x86/irq: Seperate unused system vectors from spurious entry again")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190709063402.19847-1-jslaby@suse.cz
|
|
This reverts commit 392bef709659abea614abfe53cf228e7a59876a4.
Per the discussion here:
https://lkml.kernel.org/r/201906201042.3BF5CD6@keescook
the above referenced commit breaks kernel compilation with old GCC
toolchains as well as current versions of the Gold linker.
Revert it to fix the regression and to keep the ability to compile the
kernel with these tools.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Cc: <stable@vger.kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Johannes Hirte <johannes.hirte@datenkhaos.de>
Cc: Klaus Kusche <klaus.kusche@computerix.info>
Cc: samitolvanen@google.com
Cc: Guenter Roeck <groeck@google.com>
Link: https://lkml.kernel.org/r/20190701155208.211815-1-zwisler@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The mutex mm->context->lock for init_mm is not initialized for init_mm.
This wasn't a problem because it remained unused. This changed however
since commit
4fc19708b165c ("x86/alternatives: Initialize temporary mm for patching")
Initialize the mutex for init_mm.
Fixes: 4fc19708b165c ("x86/alternatives: Initialize temporary mm for patching")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nadav Amit <namit@vmware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/20190701173354.2pe62hhliok2afea@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
M68k only provides the arch_dma_prep_coherent symbol when an mmu is
enabled and not on the coldfire platform. Fix the Kconfig symbol
selection up to match this.
Fixes: 69878ef47562 ("m68k: Implement arch_dma_prep_coherent()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
|
|
Pull ARM updates from Russell King:
- Add a "cut here" to make it clearer where oops dumps should be cut
from - we already have a marker for the end of the dumps.
- Add logging severity to show_pte()
- Drop unnecessary common-page-size linker flag
- Errata workarounds for Cortex A12 857271, Cortex A17 857272 and
Cortex A7 814220.
- Remove some unused variables that had started to provoke a compiler
warning.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8863/1: stm32: select ARM errata 814220
ARM: 8862/1: errata: 814220-B-Cache maintenance by set/way operations can execute out of order
ARM: 8865/1: mm: remove unused variables
ARM: 8864/1: Add workaround for I-Cache line size mismatch between CPU cores
ARM: 8861/1: errata: Workaround errata A12 857271 / A17 857272
ARM: 8860/1: VDSO: Drop implicit common-page-size linker flag
ARM: arrange show_pte() to issue severity-based messages
ARM: add "8<--- cut here ---" to kernel dumps
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity updates from Mimi Zohar:
"Bug fixes, code clean up, and new features:
- IMA policy rules can be defined in terms of LSM labels, making the
IMA policy dependent on LSM policy label changes, in particular LSM
label deletions. The new environment, in which IMA-appraisal is
being used, frequently updates the LSM policy and permits LSM label
deletions.
- Prevent an mmap'ed shared file opened for write from also being
mmap'ed execute. In the long term, making this and other similar
changes at the VFS layer would be preferable.
- The IMA per policy rule template format support is needed for a
couple of new/proposed features (eg. kexec boot command line
measurement, appended signatures, and VFS provided file hashes).
- Other than the "boot-aggregate" record in the IMA measuremeent
list, all other measurements are of file data. Measuring and
storing the kexec boot command line in the IMA measurement list is
the first buffer based measurement included in the measurement
list"
* 'next-integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
integrity: Introduce struct evm_xattr
ima: Update MAX_TEMPLATE_NAME_LEN to fit largest reasonable definition
KEXEC: Call ima_kexec_cmdline to measure the boot command line args
IMA: Define a new template field buf
IMA: Define a new hook to measure the kexec boot command line arguments
IMA: support for per policy rule template formats
integrity: Fix __integrity_init_keyring() section mismatch
ima: Use designated initializers for struct ima_event_data
ima: use the lsm policy update notifier
LSM: switch to blocking policy update notifiers
x86/ima: fix the Kconfig dependency for IMA_ARCH_POLICY
ima: Make arch_policy_entry static
ima: prevent a file already mmap'ed write to be mmap'ed execute
x86/ima: check EFI SetupMode too
|
|
Two cases of overlapping changes, nothing fancy.
Signed-off-by: David S. Miller <davem@davemloft.net>
|