| Age | Commit message (Collapse) | Author |
|---|
|
Since we've changed div/mod exception handling for src_reg in
eBPF verifier itself, remove the leftovers from x86_64 JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
For the BPF_REG_0 (BPF_REG_A in cBPF, respectively), we can use
the short form of the opcode as dst mapping is on eax/rax and
thus save a byte per such operation. Added to add/sub/and/or/xor
for 32/64 bit when K immediate is used. There may be more such
low-hanging fruit to add in future as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Having a pure_initcall() callback just to permanently enable BPF
JITs under CONFIG_BPF_JIT_ALWAYS_ON is unnecessary and could leave
a small race window in future where JIT is still disabled on boot.
Since we know about the setting at compilation time anyway, just
initialize it properly there. Also consolidate all the individual
bpf_jit_enable variables into a single one and move them under one
location. Moreover, don't allow for setting unspecified garbage
values on them.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Typical JIT does several passes over bpf instructions to
compute total size and relative offsets of jumps and calls.
With multitple bpf functions calling each other all relative calls
will have invalid offsets intially therefore we need to additional
last pass over the program to emit calls with correct offsets.
For example in case of three bpf functions:
main:
call foo
call bpf_map_lookup
exit
foo:
call bar
exit
bar:
exit
We will call bpf_int_jit_compile() indepedently for main(), foo() and bar()
x64 JIT typically does 4-5 passes to converge.
After these initial passes the image for these 3 functions
will be good except call targets, since start addresses of
foo() and bar() are unknown when we were JITing main()
(note that call bpf_map_lookup will be resolved properly
during initial passes).
Once start addresses of 3 functions are known we patch
call_insn->imm to point to right functions and call
bpf_int_jit_compile() again which needs only one pass.
Additional safety checks are done to make sure this
last pass doesn't produce image that is larger or smaller
than previous pass.
When constant blinding is on it's applied to all functions
at the first pass, since doing it once again at the last
pass can change size of the JITed code.
Tested on x64 and arm64 hw with JIT on/off, blinding on/off.
x64 jits bpf-to-bpf calls correctly while arm64 falls back to interpreter.
All other JITs that support normal BPF_CALL will behave the same way
since bpf-to-bpf call is equivalent to bpf-to-kernel call from
JITs point of view.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
global bpf_jit_enable variable is tested multiple times in JITs,
blinding and verifier core. The malicious root can try to toggle
it while loading the programs. This race condition was accounted
for and there should be no issues, but it's safer to avoid
this race condition.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
- bpf prog_array just like all other types of bpf array accepts 32-bit index.
Clarify that in the comment.
- fix x64 JIT of bpf_tail_call which was incorrectly loading 8 instead of 4 bytes
- tighten corresponding check in the interpreter to stay consistent
The JIT bug can be triggered after introduction of BPF_F_NUMA_NODE flag
in commit 96eabe7a40aa in 4.14. Before that the map_flags would stay zero and
though JIT code is wrong it will check bounds correctly.
Hence two fixes tags. All other JITs don't have this problem.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fixes: 96eabe7a40aa ("bpf: Allow selecting numa node during map creation")
Fixes: b52f00e6a715 ("x86: bpf_jit: implement bpf_tail_call() helper")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saves 4 bytes replacing following instructions :
lea rax, [rsi + rdx * 8 + offsetof(...)]
mov rax, qword ptr [rax]
cmp rax, 0
by :
mov rax, [rsi + rdx * 8 + offsetof(...)]
test rax, rax
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This work implements jiting of BPF_J{LT,LE,SLT,SLE} instructions
with BPF_X/BPF_K variants for the x86_64 eBPF JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
|
|
In preparation for an objtool rewrite which will have broader checks,
whitelist functions and files which cause problems because they do
unusual things with the stack.
These whitelists serve as a TODO list for which functions and files
don't yet have undwarf unwinder coverage. Eventually most of the
whitelists can be removed in favor of manual CFI hint annotations or
objtool improvements.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/7f934a5d707a574bda33ea282e9478e627fb1829.1498659915.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add jited_len to struct bpf_prog. It will be
useful for the struct bpf_prog_info which will
be added in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take advantage of stack_depth tracking in x64 JIT.
Round up allocated stack by 8 bytes to make sure it stays aligned
for functions called from JITed bpf program.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in order to JIT programs with different stack sizes we need to
make epilogue and exception path to be stack size independent,
hence move auxiliary stack space from the bottom of the stack
to the top of the stack.
Nice side effect is that JITed function prologue becomes shorter
due to imm8 offset encoding vs imm32.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
free up BPF_JMP | BPF_CALL | BPF_X opcode to be used by actual
indirect call by register and use kernel internal opcode to
mark call instruction into bpf_tail_call() helper.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-6-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For both cases, the verifier is already rejecting such invalid
formed instructions. Thus, remove these artifacts from old times
and align it with ppc64, sparc64 and s390x JITs that don't have
them in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric and Willem reported that they recently saw random crashes when
JIT was in use and bisected this to 74451e66d516 ("bpf: make jited
programs visible in traces"). Issue was that the consolidation part
added bpf_jit_binary_unlock_ro() that would unlock previously made
read-only memory back to read-write. However, DEBUG_SET_MODULE_RONX
cannot be used for this to test for presence of set_memory_*()
functions. We need to use ARCH_HAS_SET_MEMORY instead to fix this;
also add the corresponding bpf_jit_binary_lock_ro() to filter.h.
Fixes: 74451e66d516 ("bpf: make jited programs visible in traces")
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Bisected-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Long standing issue with JITed programs is that stack traces from
function tracing check whether a given address is kernel code
through {__,}kernel_text_address(), which checks for code in core
kernel, modules and dynamically allocated ftrace trampolines. But
what is still missing is BPF JITed programs (interpreted programs
are not an issue as __bpf_prog_run() will be attributed to them),
thus when a stack trace is triggered, the code walking the stack
won't see any of the JITed ones. The same for address correlation
done from user space via reading /proc/kallsyms. This is read by
tools like perf, but the latter is also useful for permanent live
tracing with eBPF itself in combination with stack maps when other
eBPF types are part of the callchain. See offwaketime example on
dumping stack from a map.
This work tries to tackle that issue by making the addresses and
symbols known to the kernel. The lookup from *kernel_text_address()
is implemented through a latched RB tree that can be read under
RCU in fast-path that is also shared for symbol/size/offset lookup
for a specific given address in kallsyms. The slow-path iteration
through all symbols in the seq file done via RCU list, which holds
a tiny fraction of all exported ksyms, usually below 0.1 percent.
Function symbols are exported as bpf_prog_<tag>, in order to aide
debugging and attribution. This facility is currently enabled for
root-only when bpf_jit_kallsyms is set to 1, and disabled if hardening
is active in any mode. The rationale behind this is that still a lot
of systems ship with world read permissions on kallsyms thus addresses
should not get suddenly exposed for them. If that situation gets
much better in future, we always have the option to change the
default on this. Likewise, unprivileged programs are not allowed
to add entries there either, but that is less of a concern as most
such programs types relevant in this context are for root-only anyway.
If enabled, call graphs and stack traces will then show a correct
attribution; one example is illustrated below, where the trace is
now visible in tooling such as perf script --kallsyms=/proc/kallsyms
and friends.
Before:
7fff8166889d bpf_clone_redirect+0x80007f0020ed (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff006451f1a007 (/usr/lib64/libc-2.18.so)
After:
7fff816688b7 bpf_clone_redirect+0x80007f002107 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa0575728 bpf_prog_33c45a467c9e061a+0x8000600020fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa07ef1fc cls_bpf_classify+0x8000600020dc (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81678b68 tc_classify+0x80007f002078 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d40b __netif_receive_skb_core+0x80007f0025fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d718 __netif_receive_skb+0x80007f002018 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164e565 process_backlog+0x80007f002095 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164dc71 net_rx_action+0x80007f002231 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81767461 __softirqentry_text_start+0x80007f0020d1 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817658ac do_softirq_own_stack+0x80007f00201c (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2c20 do_softirq+0x80007f002050 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2cb5 __local_bh_enable_ip+0x80007f002085 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168d452 ip_finish_output2+0x80007f002152 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168ea3d ip_finish_output+0x80007f00217d (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168f2af ip_output+0x80007f00203f (/lib/modules/4.9.0-rc8+/build/vmlinux)
[...]
7fff81005854 do_syscall_64+0x80007f002054 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817649eb return_from_SYSCALL_64+0x80007f002000 (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff01c484812007 (/usr/lib64/libc-2.18.so)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the dummy bpf_jit_compile() stubs for eBPF JITs and make
that a single __weak function in the core that can be overridden
similarly to the eBPF one. Also remove stale pr_err() mentions
of bpf_jit_compile.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes: 959a75791603 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds recently added constant blinding helpers into the
x86 eBPF JIT. In the bpf_int_jit_compile() path, requirements are
to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other()
pair for rewriting the program into a blinded one, and to map the
BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX
is at non-callee saved register r10, and thus shared with cached
skb->data used for ld_abs/ind and not in every program type needed.
When blinding is not used, there's zero additional overhead in the
generated image.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the blinding is strictly only called from inside eBPF JITs,
we need to change signatures for bpf_int_jit_compile() and
bpf_prog_select_runtime() first in order to prepare that the
eBPF program we're dealing with can change underneath. Hence,
for call sites, we need to return the latest prog. No functional
change in this patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is never such a situation, where bpf_int_jit_compile() is
called with either prog as NULL or len as 0, so the tests are
unnecessary and confusing as people would just copy them. s390
doesn't have them, so no change is needed there.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bpf_jit.S has several callable non-leaf functions which don't honor
CONFIG_FRAME_POINTER, which can result in bad stack traces.
Create a stack frame before the call instructions when
CONFIG_FRAME_POINTER is enabled.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/fa4c41976b438b51954cb8021f06bceb1d1d66cc.1453405861.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
bpf_jit.S has several functions which can be called from C code. Give
them proper ELF annotations.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/bbe1de0c299fecd4fc9a1766bae8be2647bedb01.1453405861.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When sometimes structs or variables need to be initialized/'memset' to 0 in
an eBPF C program, the x86 BPF JIT converts this to use immediates. We can
however save a couple of bytes (f.e. even up to 7 bytes on a single emmission
of BPF_LD | BPF_IMM | BPF_DW) in the image by detecting such case and use xor
on the dst register instead.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Back in the days where eBPF (or back then "internal BPF" ;->) was not
exposed to user space, and only the classic BPF programs internally
translated into eBPF programs, we missed the fact that for classic BPF
A and X needed to be cleared. It was fixed back then via 83d5b7ef99c9
("net: filter: initialize A and X registers"), and thus classic BPF
specifics were added to the eBPF interpreter core to work around it.
This added some confusion for JIT developers later on that take the
eBPF interpreter code as an example for deriving their JIT. F.e. in
f75298f5c3fe ("s390/bpf: clear correct BPF accumulator register"), at
least X could leak stack memory. Furthermore, since this is only needed
for classic BPF translations and not for eBPF (verifier takes care
that read access to regs cannot be done uninitialized), more complexity
is added to JITs as they need to determine whether they deal with
migrations or native eBPF where they can just omit clearing A/X in
their prologue and thus reduce image size a bit, see f.e. cde66c2d88da
("s390/bpf: Only clear A and X for converted BPF programs"). In other
cases (x86, arm64), A and X is being cleared in the prologue also for
eBPF case, which is unnecessary.
Lets move this into the BPF migration in bpf_convert_filter() where it
actually belongs as long as the number of eBPF JITs are still few. It
can thus be done generically; allowing us to remove the quirk from
__bpf_prog_run() and to slightly reduce JIT image size in case of eBPF,
while reducing code duplication on this matter in current(/future) eBPF
JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Yang Shi <yang.shi@linaro.org>
Acked-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we need to add further flags to the bpf_prog structure, lets migrate
both bools to a bitfield representation. The size of the base structure
(excluding insns) remains unchanged at 40 bytes.
Add also tags for the kmemchecker, so that it doesn't throw false
positives. Even in case gcc would generate suboptimal code, it's not
being accessed in performance critical paths.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the map backends are of generic nature. In order to avoid
adding much special code into the eBPF core, rewrite part of
the bpf_prog_array map code and make it more generic. So the
new perf_event_array map type can reuse most of code with
bpf_prog_array map and add fewer lines of special code.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When bpf_jit_compile() got split into two functions via commit
f3c2af7ba17a ("net: filter: x86: split bpf_jit_compile()"), bpf_jit_dump()
was changed to always show 0 as number of compiler passes. Change it to
dump the actual number. Also on sparc, we count passes starting from 0,
so add 1 for the debug dump as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With eBPF JIT compiler enabled on x86_64, I was able to reliably trigger
the following general protection fault out of an eBPF program with a simple
tail call, f.e. tracex5 (or a stripped down version of it):
[ 927.097918] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
[...]
[ 927.100870] task: ffff8801f228b780 ti: ffff880016a64000 task.ti: ffff880016a64000
[ 927.102096] RIP: 0010:[<ffffffffa002440d>] [<ffffffffa002440d>] 0xffffffffa002440d
[ 927.103390] RSP: 0018:ffff880016a67a68 EFLAGS: 00010006
[ 927.104683] RAX: 5a5a5a5a5a5a5a5a RBX: 0000000000000000 RCX: 0000000000000001
[ 927.105921] RDX: 0000000000000000 RSI: ffff88014e438000 RDI: ffff880016a67e00
[ 927.107137] RBP: ffff880016a67c90 R08: 0000000000000000 R09: 0000000000000001
[ 927.108351] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880016a67e00
[ 927.109567] R13: 0000000000000000 R14: ffff88026500e460 R15: ffff880220a81520
[ 927.110787] FS: 00007fe7d5c1f740(0000) GS:ffff880265000000(0000) knlGS:0000000000000000
[ 927.112021] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 927.113255] CR2: 0000003e7bbb91a0 CR3: 000000006e04b000 CR4: 00000000001407e0
[ 927.114500] Stack:
[ 927.115737] ffffc90008cdb000 ffff880016a67e00 ffff88026500e460 ffff880220a81520
[ 927.117005] 0000000100000000 000000000000001b ffff880016a67aa8 ffffffff8106c548
[ 927.118276] 00007ffcdaf22e58 0000000000000000 0000000000000000 ffff880016a67ff0
[ 927.119543] Call Trace:
[ 927.120797] [<ffffffff8106c548>] ? lookup_address+0x28/0x30
[ 927.122058] [<ffffffff8113d176>] ? __module_text_address+0x16/0x70
[ 927.123314] [<ffffffff8117bf0e>] ? is_ftrace_trampoline+0x3e/0x70
[ 927.124562] [<ffffffff810c1a0f>] ? __kernel_text_address+0x5f/0x80
[ 927.125806] [<ffffffff8102086f>] ? print_context_stack+0x7f/0xf0
[ 927.127033] [<ffffffff810f7852>] ? __lock_acquire+0x572/0x2050
[ 927.128254] [<ffffffff810f7852>] ? __lock_acquire+0x572/0x2050
[ 927.129461] [<ffffffff8119edfa>] ? trace_call_bpf+0x3a/0x140
[ 927.130654] [<ffffffff8119ee4a>] trace_call_bpf+0x8a/0x140
[ 927.131837] [<ffffffff8119edfa>] ? trace_call_bpf+0x3a/0x140
[ 927.133015] [<ffffffff8119f008>] kprobe_perf_func+0x28/0x220
[ 927.134195] [<ffffffff811a1668>] kprobe_dispatcher+0x38/0x60
[ 927.135367] [<ffffffff81174b91>] ? seccomp_phase1+0x1/0x230
[ 927.136523] [<ffffffff81061400>] kprobe_ftrace_handler+0xf0/0x150
[ 927.137666] [<ffffffff81174b95>] ? seccomp_phase1+0x5/0x230
[ 927.138802] [<ffffffff8117950c>] ftrace_ops_recurs_func+0x5c/0xb0
[ 927.139934] [<ffffffffa022b0d5>] 0xffffffffa022b0d5
[ 927.141066] [<ffffffff81174b91>] ? seccomp_phase1+0x1/0x230
[ 927.142199] [<ffffffff81174b95>] seccomp_phase1+0x5/0x230
[ 927.143323] [<ffffffff8102c0a4>] syscall_trace_enter_phase1+0xc4/0x150
[ 927.144450] [<ffffffff81174b95>] ? seccomp_phase1+0x5/0x230
[ 927.145572] [<ffffffff8102c0a4>] ? syscall_trace_enter_phase1+0xc4/0x150
[ 927.146666] [<ffffffff817f9a9f>] tracesys+0xd/0x44
[ 927.147723] Code: 48 8b 46 10 48 39 d0 76 2c 8b 85 fc fd ff ff 83 f8 20 77 21 83
c0 01 89 85 fc fd ff ff 48 8d 44 d6 80 48 8b 00 48 83 f8 00 74
0a <48> 8b 40 20 48 83 c0 33 ff e0 48 89 d8 48 8b 9d d8 fd ff
ff 4c
[ 927.150046] RIP [<ffffffffa002440d>] 0xffffffffa002440d
The code section with the instructions that traps points into the eBPF JIT
image of the root program (the one invoking the tail call instruction).
Using bpf_jit_disasm -o on the eBPF root program image:
[...]
4e: mov -0x204(%rbp),%eax
8b 85 fc fd ff ff
54: cmp $0x20,%eax <--- if (tail_call_cnt > MAX_TAIL_CALL_CNT)
83 f8 20
57: ja 0x000000000000007a
77 21
59: add $0x1,%eax <--- tail_call_cnt++
83 c0 01
5c: mov %eax,-0x204(%rbp)
89 85 fc fd ff ff
62: lea -0x80(%rsi,%rdx,8),%rax <--- prog = array->prog[index]
48 8d 44 d6 80
67: mov (%rax),%rax
48 8b 00
6a: cmp $0x0,%rax <--- check for NULL
48 83 f8 00
6e: je 0x000000000000007a
74 0a
70: mov 0x20(%rax),%rax <--- GPF triggered here! fetch of bpf_func
48 8b 40 20 [ matches <48> 8b 40 20 ... from above ]
74: add $0x33,%rax <--- prologue skip of new prog
48 83 c0 33
78: jmpq *%rax <--- jump to new prog insns
ff e0
[...]
The problem is that rax has 5a5a5a5a5a5a5a5a, which suggests a tail call
jump to map slot 0 is pointing to a poisoned page. The issue is the following:
lea instruction has a wrong offset, i.e. it should be ...
lea 0x80(%rsi,%rdx,8),%rax
... but it actually seems to be ...
lea -0x80(%rsi,%rdx,8),%rax
... where 0x80 is offsetof(struct bpf_array, prog), thus the offset needs
to be positive instead of negative. Disassembling the interpreter, we btw
similarly do:
[...]
c88: lea 0x80(%rax,%rdx,8),%rax <--- prog = array->prog[index]
48 8d 84 d0 80 00 00 00
c90: add $0x1,%r13d
41 83 c5 01
c94: mov (%rax),%rax
48 8b 00
[...]
Now the other interesting fact is that this panic triggers only when things
like CONFIG_LOCKDEP are being used. In that case offsetof(struct bpf_array,
prog) starts at offset 0x80 and in non-CONFIG_LOCKDEP case at offset 0x50.
Reason is that the work_struct inside struct bpf_map grows by 48 bytes in my
case due to the lockdep_map member (which also has CONFIG_LOCK_STAT enabled
members).
Changing the emitter to always use the 4 byte displacement in the lea
instruction fixes the panic on my side. It increases the tail call instruction
emission by 3 more byte, but it should cover us from various combinations
(and perhaps other future increases on related structures).
After patch, disassembly:
[...]
9e: lea 0x80(%rsi,%rdx,8),%rax <--- CONFIG_LOCKDEP/CONFIG_LOCK_STAT
48 8d 84 d6 80 00 00 00
a6: mov (%rax),%rax
48 8b 00
[...]
[...]
9e: lea 0x50(%rsi,%rdx,8),%rax <--- No CONFIG_LOCKDEP
48 8d 84 d6 50 00 00 00
a6: mov (%rax),%rax
48 8b 00
[...]
Fixes: b52f00e6a715 ("x86: bpf_jit: implement bpf_tail_call() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow eBPF programs attached to TC qdiscs call skb_vlan_push/pop via
helper functions. These functions may change skb->data/hlen which are
cached by some JITs to improve performance of ld_abs/ld_ind instructions.
Therefore JITs need to recognize bpf_skb_vlan_push/pop() calls,
re-compute header len and re-cache skb->data/hlen back into cpu registers.
Note, skb->data/hlen are not directly accessible from the programs,
so any changes to skb->data done either by these helpers or by other
TC actions are safe.
eBPF JIT supported by three architectures:
- arm64 JIT is using bpf_load_pointer() without caching, so it's ok as-is.
- x64 JIT re-caches skb->data/hlen unconditionally after vlan_push/pop calls
(experiments showed that conditional re-caching is slower).
- s390 JIT falls back to interpreter for now when bpf_skb_vlan_push() is present
in the program (re-caching is tbd).
These helpers allow more scalable handling of vlan from the programs.
Instead of creating thousands of vlan netdevs on top of eth0 and attaching
TC+ingress+bpf to all of them, the program can be attached to eth0 directly
and manipulate vlans as necessary.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
|
|
Collect all changes to arch/x86/entry/entry_64.S, before applying
patch that changes most of the file.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
So the dwarf2 annotations in low level assembly code have
become an increasing hindrance: unreadable, messy macros
mixed into some of the most security sensitive code paths
of the Linux kernel.
These debug info annotations don't even buy the upstream
kernel anything: dwarf driven stack unwinding has caused
problems in the past so it's out of tree, and the upstream
kernel only uses the much more robust framepointers based
stack unwinding method.
In addition to that there's a steady, slow bitrot going
on with these annotations, requiring frequent fixups.
There's no tooling and no functionality upstream that
keeps it correct.
So burn down the sick forest, allowing new, healthier growth:
27 files changed, 350 insertions(+), 1101 deletions(-)
Someone who has the willingness and time to do this
properly can attempt to reintroduce dwarf debuginfo in x86
assembly code plus dwarf unwinding from first principles,
with the following conditions:
- it should be maximally readable, and maximally low-key to
'ordinary' code reading and maintenance.
- find a build time method to insert dwarf annotations
automatically in the most common cases, for pop/push
instructions that manipulate the stack pointer. This could
be done for example via a preprocessing step that just
looks for common patterns - plus special annotations for
the few cases where we want to depart from the default.
We have hundreds of CFI annotations, so automating most of
that makes sense.
- it should come with build tooling checks that ensure that
CFI annotations are sensible. We've seen such efforts from
the framepointer side, and there's no reason it couldn't be
done on the dwarf side.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
x86 has variable length encoding. x86 JIT compiler is trying
to pick the shortest encoding for given bpf instruction.
While doing so the jump targets are changing, so JIT is doing
multiple passes over the program. Typical program needs 3 passes.
Some very short programs converge with 2 passes. Large programs
may need 4 or 5. But specially crafted bpf programs may hit the
pass limit and if the program converges on the last iteration
the JIT compiler will be producing an image full of 'int 3' insns.
Fix this corner case by doing final iteration over bpf program.
Fixes: 0a14842f5a3c ("net: filter: Just In Time compiler for x86-64")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bpf_tail_call() arguments:
ctx - context pointer
jmp_table - one of BPF_MAP_TYPE_PROG_ARRAY maps used as the jump table
index - index in the jump table
In this implementation x64 JIT bypasses stack unwind and jumps into the
callee program after prologue, so the callee program reuses the same stack.
The logic can be roughly expressed in C like:
u32 tail_call_cnt;
void *jumptable[2] = { &&label1, &&label2 };
int bpf_prog1(void *ctx)
{
label1:
...
}
int bpf_prog2(void *ctx)
{
label2:
...
}
int bpf_prog1(void *ctx)
{
...
if (tail_call_cnt++ < MAX_TAIL_CALL_CNT)
goto *jumptable[index]; ... and pass my 'ctx' to callee ...
... fall through if no entry in jumptable ...
}
Note that 'skip current program epilogue and next program prologue' is
an optimization. Other JITs don't have to do it the same way.
>From safety point of view it's valid as well, since programs always
initialize the stack before use, so any residue in the stack left by
the current program is not going be read. The same verifier checks are
done for the calls from the kernel into all bpf programs.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FROM_BE16:
'ror %reg, 8' doesn't clear upper bits of the register,
so use additional 'movzwl' insn to zero extend 16 bits into 64
FROM_LE16:
should zero extend lower 16 bits into 64 bit
FROM_LE32:
should zero extend lower 32 bits into 64 bit
Fixes: 89aa075832b0 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let the compiler decide instead.
No change in object size x86-64 -O2 no profiling
Signed-off-by: Joe Perches <joe@perches.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the (1 << reg) & mask trick to reduce code size.
x86-64 size difference -O2 without profiling for various
gcc versions:
$ size arch/x86/net/bpf_jit_comp.o*
text data bss dec hex filename
9266 4 0 9270 2436 arch/x86/net/bpf_jit_comp.o.4.4.new
10042 4 0 10046 273e arch/x86/net/bpf_jit_comp.o.4.4.old
9109 4 0 9113 2399 arch/x86/net/bpf_jit_comp.o.4.6.new
9717 4 0 9721 25f9 arch/x86/net/bpf_jit_comp.o.4.6.old
8789 4 0 8793 2259 arch/x86/net/bpf_jit_comp.o.4.7.new
10245 4 0 10249 2809 arch/x86/net/bpf_jit_comp.o.4.7.old
9671 4 0 9675 25cb arch/x86/net/bpf_jit_comp.o.4.9.new
10679 4 0 10683 29bb arch/x86/net/bpf_jit_comp.o.4.9.old
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
classic BPF has a restriction that last insn is always BPF_RET.
eBPF doesn't have BPF_RET instruction and this restriction.
It has BPF_EXIT insn which can appear anywhere in the program
one or more times and it doesn't have to be last insn.
Fix eBPF JIT to emit epilogue when first BPF_EXIT is seen
and all other BPF_EXIT instructions will be emitted as jump.
Since jump offset to epilogue is computed as:
jmp_offset = ctx->cleanup_addr - addrs[i]
we need to change type of cleanup_addr to signed to compute the offset as:
(long long) ((int)20 - (int)30)
instead of:
(long long) ((unsigned int)20 - (int)30)
Fixes: 622582786c9e ("net: filter: x86: internal BPF JIT")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1.
JIT compiler using multi-pass approach to converge to final image size,
since x86 instructions are variable length. It starts with large
gaps between instructions (so some jumps may use imm32 instead of imm8)
and iterates until total program size is the same as in previous pass.
This algorithm works only if program size is strictly decreasing.
Programs that use LD_ABS insn need additional code in prologue, but it
was not emitted during 1st pass, so there was a chance that 2nd pass would
adjust imm32->imm8 jump offsets to the same number of bytes as increase in
prologue, which may cause algorithm to erroneously decide that size converged.
Fix it by always emitting largest prologue in the first pass which
is detected by oldproglen==0 check.
Also change error check condition 'proglen != oldproglen' to fail gracefully.
2.
while staring at the code realized that 64-byte buffer may not be enough
when 1st insn is large, so increase it to 128 to avoid buffer overflow
(theoretical maximum size of prologue+div is 109) and add runtime check.
Fixes: 622582786c9e ("net: filter: x86: internal BPF JIT")
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported by Mikulas Patocka, kmemcheck currently barks out a
false positive since we don't have special kmemcheck annotation
for bitfields used in bpf_prog structure.
We currently have jited:1, len:31 and thus when accessing len
while CONFIG_KMEMCHECK enabled, kmemcheck throws a warning that
we're reading uninitialized memory.
As we don't need the whole bit universe for pages member, we
can just split it to u16 and use a bool flag for jited instead
of a bitfield.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduced in commit 314beb9bcabf ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks") and later on replicated in aa2d2c73c21f
("s390/bpf,jit: address randomize and write protect jit code") for
s390 architecture, write protection for BPF JIT images got added and
a random start address of the JIT code, so that it's not on a page
boundary anymore.
Since both use a very similar allocator for the BPF binary header,
we can consolidate this code into the BPF core as it's mostly JIT
independant anyway.
This will also allow for future archs that support DEBUG_SET_MODULE_RONX
to just reuse instead of reimplementing it.
JIT tested on x86_64 and s390x with BPF test suite.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add BPF_LD_IMM64 instruction to load 64-bit immediate value into a register.
All previous instructions were 8-byte. This is first 16-byte instruction.
Two consecutive 'struct bpf_insn' blocks are interpreted as single instruction:
insn[0].code = BPF_LD | BPF_DW | BPF_IMM
insn[0].dst_reg = destination register
insn[0].imm = lower 32-bit
insn[1].code = 0
insn[1].imm = upper 32-bit
All unused fields must be zero.
Classic BPF has similar instruction: BPF_LD | BPF_W | BPF_IMM
which loads 32-bit immediate value into a register.
x64 JITs it as single 'movabsq %rax, imm64'
arm64 may JIT as sequence of four 'movk x0, #imm16, lsl #shift' insn
Note that old eBPF programs are binary compatible with new interpreter.
It helps eBPF programs load 64-bit constant into a register with one
instruction instead of using two registers and 4 instructions:
BPF_MOV32_IMM(R1, imm32)
BPF_ALU64_IMM(BPF_LSH, R1, 32)
BPF_MOV32_IMM(R2, imm32)
BPF_ALU64_REG(BPF_OR, R1, R2)
User space generated programs will use this instruction to load constants only.
To tell kernel that user space needs a pointer the _pseudo_ variant of
this instruction may be added later, which will use extra bits of encoding
to indicate what type of pointer user space is asking kernel to provide.
For example 'off' or 'src_reg' fields can be used for such purpose.
src_reg = 1 could mean that user space is asking kernel to validate and
load in-kernel map pointer.
src_reg = 2 could mean that user space needs readonly data section pointer
src_reg = 3 could mean that user space needs a pointer to per-cpu local data
All such future pseudo instructions will not be carrying the actual pointer
as part of the instruction, but rather will be treated as a request to kernel
to provide one. The kernel will verify the request_for_a_pointer, then
will drop _pseudo_ marking and will store actual internal pointer inside
the instruction, so the end result is the interpreter and JITs never
see pseudo BPF_LD_IMM64 insns and only operate on generic BPF_LD_IMM64 that
loads 64-bit immediate into a register. User space never operates on direct
pointers and verifier can easily recognize request_for_pointer vs other
instructions.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With eBPF getting more extended and exposure to user space is on it's way,
hardening the memory range the interpreter uses to steer its command flow
seems appropriate. This patch moves the to be interpreted bytecode to
read-only pages.
In case we execute a corrupted BPF interpreter image for some reason e.g.
caused by an attacker which got past a verifier stage, it would not only
provide arbitrary read/write memory access but arbitrary function calls
as well. After setting up the BPF interpreter image, its contents do not
change until destruction time, thus we can setup the image on immutable
made pages in order to mitigate modifications to that code. The idea
is derived from commit 314beb9bcabf ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks").
This is possible because bpf_prog is not part of sk_filter anymore.
After setup bpf_prog cannot be altered during its life-time. This prevents
any modifications to the entire bpf_prog structure (incl. function/JIT
image pointer).
Every eBPF program (including classic BPF that are migrated) have to call
bpf_prog_select_runtime() to select either interpreter or a JIT image
as a last setup step, and they all are being freed via bpf_prog_free(),
including non-JIT. Therefore, we can easily integrate this into the
eBPF life-time, plus since we directly allocate a bpf_prog, we have no
performance penalty.
Tested with seccomp and test_bpf testsuite in JIT/non-JIT mode and manual
inspection of kernel_page_tables. Brad Spengler proposed the same idea
via Twitter during development of this patch.
Joint work with Hannes Frederic Sowa.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
