| Age | Commit message (Collapse) | Author |
|---|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Meelis Roos reported that kernels built with gcc-4.9 do not boot, we
eventually narrowed this down to only impacting machines using
UltraSPARC-III and derivitive cpus.
The crash happens right when the first user process is spawned:
[ 54.451346] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
[ 54.451346]
[ 54.571516] CPU: 1 PID: 1 Comm: init Not tainted 3.16.0-rc2-00211-gd7933ab #96
[ 54.666431] Call Trace:
[ 54.698453] [0000000000762f8c] panic+0xb0/0x224
[ 54.759071] [000000000045cf68] do_exit+0x948/0x960
[ 54.823123] [000000000042cbc0] fault_in_user_windows+0xe0/0x100
[ 54.902036] [0000000000404ad0] __handle_user_windows+0x0/0x10
[ 54.978662] Press Stop-A (L1-A) to return to the boot prom
[ 55.050713] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
Further investigation showed that compiling only per_cpu_patch() with
an older compiler fixes the boot.
Detailed analysis showed that the function is not being miscompiled by
gcc-4.9, but it is using a different register allocation ordering.
With the gcc-4.9 compiled function, something during the code patching
causes some of the %i* input registers to get corrupted. Perhaps
we have a TLB miss path into the firmware that is deep enough to
cause a register window spill and subsequent restore when we get
back from the TLB miss trap.
Let's plug this up by doing two things:
1) Stop using the firmware stack for client interface calls into
the firmware. Just use the kernel's stack.
2) As soon as we can, call into a new function "start_early_boot()"
to put a one-register-window buffer between the firmware's
deepest stack frame and the top-most initial kernel one.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inconsistently, the raw_* IRQ routines do not interact with and update
the irqflags tracing and lockdep state, whereas the raw_* spinlock
interfaces do.
This causes problems in p1275_cmd_direct() because we disable hardirqs
by hand using raw_local_irq_restore() and then do a raw_spin_lock()
which triggers a lockdep trace because the CPU's hw IRQ state doesn't
match IRQ tracing's internal software copy of that state.
The CPU's irqs are disabled, yet current->hardirqs_enabled is true.
====================
reboot: Restarting system
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:3536 check_flags+0x7c/0x240()
DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
Modules linked in: openpromfs
CPU: 0 PID: 1 Comm: systemd-shutdow Tainted: G W 3.17.0-dirty #145
Call Trace:
[000000000045919c] warn_slowpath_common+0x5c/0xa0
[0000000000459210] warn_slowpath_fmt+0x30/0x40
[000000000048f41c] check_flags+0x7c/0x240
[0000000000493280] lock_acquire+0x20/0x1c0
[0000000000832b70] _raw_spin_lock+0x30/0x60
[000000000068f2fc] p1275_cmd_direct+0x1c/0x60
[000000000068ed28] prom_reboot+0x28/0x40
[000000000043610c] machine_restart+0x4c/0x80
[000000000047d2d4] kernel_restart+0x54/0x80
[000000000047d618] SyS_reboot+0x138/0x200
[00000000004060b4] linux_sparc_syscall32+0x34/0x60
---[ end trace 5c439fe81c05a100 ]---
possible reason: unannotated irqs-off.
irq event stamp: 2010267
hardirqs last enabled at (2010267): [<000000000049a358>] vprintk_emit+0x4b8/0x580
hardirqs last disabled at (2010266): [<0000000000499f08>] vprintk_emit+0x68/0x580
softirqs last enabled at (2010046): [<000000000045d278>] __do_softirq+0x378/0x4a0
softirqs last disabled at (2010039): [<000000000042bf08>] do_softirq_own_stack+0x28/0x40
Resetting ...
====================
Use local_* variables of the hw IRQ interfaces so that IRQ tracing sees
all of our changes.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disintegrate asm/system.h for Sparc.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: sparclinux@vger.kernel.org
|
|
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
|
|
This is based upon a report by Meelis Roos showing that it's possible
that we'll try to fetch a property that is 32K in size with some
devices. With the current fixed 3K buffer we use for moving data in
and out of the firmware during PROM calls, that simply won't work.
In fact, it will scramble random kernel data during bootup.
The reasoning behind the temporary buffer is entirely historical. It
used to be the case that we had problems referencing dynamic kernel
memory (including the stack) early in the boot process before we
explicitly told the firwmare to switch us over to the kernel trap
table.
So what we did was always give the firmware buffers that were locked
into the main kernel image.
But we no longer have problems like that, so get rid of all of this
indirect bounce buffering.
Besides fixing Meelis's bug, this also makes the kernel data about 3K
smaller.
It was also discovered during these conversions that the
implementation of prom_retain() was completely wrong, so that was
fixed here as well. Currently that interface is not in use.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we do something like try to print to the OF console from an NMI
while we're already in OpenFirmware, we'll deadlock on the spinlock.
Use a raw spinlock and disable NMIs when we take it.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- all files with identical names copied and renamed to *_64.c
- the remaning files copied as is
- added sparc64 specific files to sparc/prom/Makefile
- teach sparc64 Makefile to look into sparc/prom/
- delete unused Makefile from sparc64/prom/
linking order was not kept for sparc64 with this change.
It was not possible to keep linking order for both sparc and sparc64
and as sparc64 see more testing than sparc it was natural to
break linking order on sparc64. Should it have any effect it
would be detected sooner this way.
printf_32.c and printf_64.c are obvious candidates to be merged
but they are not 100% equal so that was left for later
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
