| Age | Commit message (Collapse) | Author |
|---|
|
This adds optimized memset/bzero/page-clear routines for Niagara-4.
We basically can do what powerpc has been able to do for a decade (via
the "dcbz" instruction), which is use cache line clearing stores for
bzero and memsets with a 'c' argument of zero.
As long as we make the cache initializing store to each 32-byte
subblock of the L2 cache line, it works.
As with other Niagara-4 optimized routines, the key is to make sure to
avoid any usage of the %asi register, as reads and writes to it cost
at least 50 cycles.
For the user clear cases, we don't use these new routines, we use the
Niagara-1 variants instead. Those have to use %asi in an unavoidable
way.
A Niagara-4 8K page clear costs just under 600 cycles.
Add definitions of the MRU variants of the cache initializing store
ASIs. By default, cache initializing stores install the line as Least
Recently Used. If we know we're going to use the data immediately
(which is true for page copies and clears) we can use the Most
Recently Used variant, to decrease the likelyhood of the lines being
evicted before they get used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before After
-------------- --------------
bw_tcp: 1288.53 MB/sec 1637.77 MB/sec
bw_pipe: 1517.18 MB/sec 2107.61 MB/sec
bw_unix: 1838.38 MB/sec 2640.91 MB/sec
make -s -j128
allmodconfig 5min 49sec 5min 31sec
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To allow us to add ttable_32.S
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recognize T4 and T5 chips. Treating them both as "T2 plus other
stuff" should be extremely safe and make sure distributions will work
when those chips actually ship to customers.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't use floating point on Niagara2, use the traditional
plain Niagara code instead.
Unroll Niagara loops to 128 bytes for copy, and 256 bytes
for clear.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpu compatible string we look for is "SPARC-T3".
As far as memset/memcpy optimizations go, we treat this chip the same
as Niagara-T2/T2+. Use cache initializing stores for memset, and use
perfetch, FPU block loads, cache initializing stores, and block stores
for copies.
We use the Niagara-T2 perf support, since T3 is a close relative in
this regard. Later we'll add support for the new events T3 can
report, plus enable T3's new "sample" mode.
For now I haven't added any new ELF hwcap flags. We probably need
to add a couple, for example:
T2 and T3 both support the population count instruction in hardware.
T3 supports VIS3 instructions, including support (finally) for
partitioned shift. One can also now move directly between float
and integer registers.
T3 supports instructions meant to help with Galois Field and other HPC
calculations, such as XOR multiply. Also there are "OP and negate"
instructions, for example "fnmul" which is multiply-and-negate.
T3 recognizes the transactional memory opcodes, however since
transactional memory isn't supported: 1) 'commit' behaves as a NOP and
2) 'chkpt' always branches 3) 'rdcps' returns all zeros and 4) 'wrcps'
behaves as a NOP.
So we'll need about 3 new elf capability flags in the end to represent
all of these things.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Surprisingly this actually makes LOAD_PER_CPU_BASE() a little
more efficient.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The section .text.init.refok is deprecated and __REF (.ref.text)
should be used in assembly files instead. This patch cleans up a few
uses of .text.init.refok in the sparc architecture.
Also fix a reference to .text.init in a comment that wasn't updated to
.init.text.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix misspelling of firmware.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This is an implementation of a suggestion made by Chris Torek:
--------------------
Something else I noticed in passing: the EX and EX_LD/EX_ST macros
scattered throughout the various .S files make a fair bit of .fixup
code, all of which does the same thing. At the cost of one symbol
in copy_in_user.S, you could just have one common two-instruction
retl-and-mov-1 fixup that they all share.
--------------------
The following is with a defconfig build:
text data bss dec hex filename
3972767 344024 584449 4901240 4ac978 vmlinux.orig
3968887 344024 584449 4897360 4aba50 vmlinux
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Move all files from sparc64/kernel/ to sparc/kernel
- rename as appropriate
o Update sparc/Makefile to the changes
o Update sparc/kernel/Makefile to include the sparc64 files
NOTE: This commit changes link order on sparc64!
Link order had to change for either of sparc32 and sparc64.
And assuming sparc64 see more testing than sparc32 change link
order on sparc64 where issues will be caught faster.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
