| Age | Commit message (Collapse) | Author |
|---|
|
Add code to allow boards registering self-contained
functions for going to/from self-refresh. At this
point the board code is unused. When all supported
boards have been converted then the new sleep code
will make use of these functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Make use of the recently added notifier chains for sh7724
r-standby register save/restore handling. At this point
only the BSC and INTC are handled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds atomic notifier chains for pre/post
sleep events. Useful for cpu code and boards that
need to save and restore register state before and
after entering a sleep mode.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
num_events should be compared > MAX_HWEVENTS and not >=. The latter was
used as a debugging test which accidentally slipped in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds in preliminary support for the SH-4A performance counters.
Presently only the first 2 counters are supported, as these are the ones
of the most interest to the perf tool and end users. Counter chaining is
not presently handled, so these are simply implemented as 32-bit
counters.
This also establishes a perf event support framework for other hardware
counters, which the existing SH-4 oprofile code will migrate over to as
the SH-4A support evolves.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Many of these symbols went away completely, or we just never cared about
them in the first place. Trim the exports down to the essential set.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
These were previously hidden in sh_ksyms_32, despite also being needed
for sh64 now that the cache.c code is shared.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Leaving this configurable caused more trouble than it was ever worth, so
just make it explicit. Boards that are verified one way or the other can
fix up their selects accordingly. We presently default to non-coherent
for most platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Now that SH's irqflags functions are out of line it becomes necessary to
mark them as "notrace" so that we don't try to trace them.
[ Do the same for irq_64.c -- PFM. ]
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This unbreaks kexec support. Without this fix all
cases of kexec fails since __pa() does not behave
like PHYSADDR(). The downside is that we also kill
the code blocking users running old kexec-tools.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Conflicts:
arch/sh/kernel/dwarf.c
|
|
When CONFIG_FUNCTION_GRAPH_TRACER is enabled the function graph tracer
may patch return addresses on the stack with the address of
return_to_handler(). This really confuses the DWARF unwinder because it
will try find the caller of return_to_handler(), not the caller of the
real return address.
So teach the DWARF unwinder how to find the real return address whenever
it encounters return_to_handler().
This patch does not cope very well when multiple return addresses on the
stack have been patched. To make it work properly it would require state
to track how many return_to_handler()'s have been seen so that we'd know
where to look in current->curr_ret_stack[]. So for now, instead of
trying to handle this, just moan if more than one return address on the
stack has been patched.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
ERROR: "__movmemSI12" [net/unix/unix.ko] undefined!
ERROR: "__movmemSI52" [net/ipv6/sit.ko] undefined!
ERROR: "__movmemSI24" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI60" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI16" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI20" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI32" [net/ipv6/ipv6.ko] undefined!
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds an __irq_entry annotation for do_IRQ() so that the IRQ
annotation in the function graph tracer works as advertized. We already
have the IRQENTRY section wired up, so this is just a trivial addition
to actually make use of it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This moves the current dma_alloc/free_coherent() calls to a generic
variant and plugs them in for the nommu default. Other variants can
override the defaults in the dma mapping ops directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This converts the old DMA mapping support to the new generic
dma-mapping-common.h abstraction.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fixes up flush_dcache_page() references by modules with run-time cache
disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
SCIF2 and the FPU exceptions happen to share vector numbers, one in
EXPEVT and the other in INTEVT. This is a violation of the interface and
should have never made it in to silicon. On top of that, the demux hack
that was added for special dispatch is rather error prone, and introduces
more problems than it solves. Kill all of it off, and just refuse to deal
with SCIF2 outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This simplifies the irqflags support by switching over to the asm-generic
version. The necessary support functions are brought out-of-line for both
SHcompact and SHmedia instruction sets.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This code was added for some ancient SH-4 solution engines with peculiar
boot ROMs that did silly things to the UBC MSTP bits. None of these have
been in the wild for years, and these days the clock framework wraps up
the MSTP bits, meaning that the UBC code is one of the few interfaces
that is stomping MSTP bits underneath the clock framework. At this point
the risks far outweigh any benefit this code provided, so just kill it
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This enables SCHED_MC support for SH-X3 multi-cores. Presently this is
just a simple wrapper around the possible map, but this allows for
tying in support for some of the more exotic NUMA clusters where we can
actually do something with the topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
In the case where need_resched() is set in between the cpu_idle() and
pm_idle() calls we were missing an else case for just re-enabling local
IRQs and bailing out. This was noticed by the irqs_disabled() warning,
even though IRQs were being re-enabled elsewhere.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This follows the x86 change and moves check_pgt_cache() up under the
!need_resched() tight loop, rather than simply calling in to it when
exiting idle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This does a bit of chainsawing of the idle loop code to get light sleep
working on SMP. Previously this was forcing secondary CPUs in to sleep
mode with them not coming back if they didn't have their own local
timers. Given that we use clockevents broadcasting by default, the CPU
managing the clockevents can't have IRQs disabled before entering its
sleep state.
This unfortunately leaves us with the age-old need_resched() race in
between local_irq_enable() and cpu_sleep(), but at present this is
unavoidable. After some more experimentation it may be possible to layer
on SR.BL bit manipulation over top of this scheme to inhibit the race
condition, but given the current potential for missing wakeups, this is
left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
All of the secondary CPUs are forced in to light sleep mode, but we were
missing the same initialization for the boot CPU. This resulted in
inconsistent sleep modes depending on which CPU we were on, confusing the
idle loop when not polling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This plugs in support for NMI counting per-CPU via irq_cpustat_t.
Modelled after the x86 implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Replace TIF_RESTORE_SIGMASK with TS_RESTORE_SIGMASK and define our own
set_restore_sigmask() function. This saves the costly SMP-safe set_bit
operation, which we do not need for the sigmask flag since TIF_SIGPENDING
always has to be set too.
Based on the x86 and powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
The resume_userspace path had TRACE_IRQS_OFF written incorrectly and so
never handled the transition properly. This was fixed once before but
seems to have made it back in the tree. Fix it for good.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This only needs to flush the return code via the legacy path, and just
invalidates uselessly otherwise. This makes the behaviour consistent for
all of the trampoline setup paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The secondary CPU info was seeing corrupted results due to not entering
all of the setup paths taken by the boot CPU. So we just memcpy() the
boot cpu data over directly, and then fix up the per-CPU bits.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Trivial change for cleaning up the cpuinfo pretty printing on SMP, adds a
newline between CPUs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
We do not want to use smp_processor_id() from these paths, as they trip
preempt BUGs. Switch the test over to the boot cpu directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Secondary CPUs already take care of the D-cache bits through the common
cache initialization path, and the only thing that is necessary after
twiddling around with stack_start is ensuring that the I-cache changes
are visible (particularly since this tends to be the only part lacking
coherency).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This cribs the x86 implementation of ftrace_nmi_enter() and friends to
make ftrace_modify_code() NMI safe, particularly on SMP configurations.
For additional notes on the problems involved, see the comment below
ftrace_call_replace().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds return_address.c to the -pg exclusion list, as this is the
building block for CALLER_ADDRx we do not want to profile this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This enables us to build the dwarf unwinder both with modules enabled and
disabled in addition to reducing code size in the latter case. The
helpers are also consolidated, and modified to resemble the BUG module
helpers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This splits out the unwinder implementation and adds a new
return_address() abstraction modelled after the ARM code. The DWARF
unwinder is tied in to this, returning NULL otherwise in the case of
being unable to support arbitrary depths.
This enables us to get correct behaviour with the unwinder enabled,
as well as disabling the arbitrary depth support when frame pointers are
enabled, as arbitrary depths with __builtin_return_address() are not
supported regardless.
With this abstraction it's also possible to layer on a simplified
implementation with frame pointers in the event that the unwinder isn't
enabled, although this is left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
Sync up with latest core changes in the syscalls tracing area:
- tracing: Map syscall name to number (syscall_name_to_nr())
- tracing: Call arch_init_ftrace_syscalls at boot
- tracing: add support tracepoint ids (set_syscall_{enter,exit}_id())
Taken from the s390 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
This follows the ARM change, as SH had all of the same issues:
Make die() better match x86:
- add printing of the last accessed sysfs file
- ensure console_verbose() is called under the lock
- ensure we panic outside of oops_exit()
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Conflicts:
arch/sh/kernel/dwarf.c
|
|
sh/dwarf-unwinder
|
|
Originally, dwarf_unwind_stack() was a recursive function and it seems
that some of the old comments were never updated.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
|
|
If we broke out of the while (1) loop because the return address of
"frame" was zero, then "frame" needs to be free'd before we return.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
|
|
Pass a module's .eh_frame section to the DWARF unwinder at module load
time so that the section's FDEs and CIEs can be registered with the
DWARF unwinder. This allows us to unwind the stack through module code
when generating backtraces.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
|
|
In the multi-evt conversion for the SH-X3 proto CPU, IRLs were dropped
down to a single unique masking source, which ended up blowing up on
ILSEL-based IRQs which have special semantics that otherwise confuse the
intc code. While this does result in intc spewing about not having a
unique masking source, we don't really care.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The initialisation process differs for CONFIG_PMB and for
CONFIG_PMB_FIXED. For CONFIG_PMB_FIXED we need to register the PMB
entries that were allocated by the bootloader.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
