| Age | Commit message (Collapse) | Author |
|---|
|
It turned out that SIGP set-multi-threading can only be done once.
Therefore switching to a different MT level after switching to
sclp.mtid_prev in the dump case fails.
As a symptom specifying the "nosmt" parameter currently fails for
the kdump kernel and the kernel starts with multi-threading enabled.
So fix this and issue diag 308 subcode 1 call after collecting the
CPU states for the dump. Also enhance the diag308_reset() function to
be usable also with enabled lowcore protection and prefix register != 0.
After the reset it is possible to switch the MT level again. We have
to do the reset very early in order not to kill the already initialized
console. Therefore instead of kmalloc() the corresponding memblock
functions have to be used. To avoid copying the sclp cpu code into
sclp_early, we now use the simple sigp loop method for CPU detection.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.
The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e5826 ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.
Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The multi-threading facility is introduced with the z13 processor family.
This patch adds code to detect the multi-threading facility. With the
facility enabled each core will surface multiple hardware threads to the
system. Each hardware threads looks like a normal CPU to the operating
system with all its registers and properties.
The SCLP interface reports the SMT topology indirectly via the maximum
thread id. Each reported CPU in the result of a read-scp-information
is a core representing a number of hardware threads.
To reflect the reduced CPU capacity if two hardware threads run on a
single core the MT utilization counter set is used to normalize the
raw cputime obtained by the CPU timer deltas. This scaled cputime is
reported via the taskstats interface. The normal /proc/stat numbers
are based on the raw cputime and are not affected by the normalization.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Use sigp order code defines in assembly code as well.
With this change all places that use sigp constants should
have been converted to use self describing defines instead
of directly using constants.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Currently the PSW restart handler and kexec are executed in real
mode with DAT=off. For kexec/kdump the function setup_regs() is
called that uses the per-cpu variable "crash_notes". Because
there are situations when the per-cpu implementation uses vmalloc
memory, calling setup_regs() in real mode can cause a program
check interrupt.
To fix that problem this patch changes the following:
* Ensure that diag308_reset() does not change PSW bits to real mode
* Enable DAT in __do_restart() after we switched to an online CPU
* Enable DAT in __machine_kexec() after we switched to the IPL CPU
* Call setup_regs() before we switch to real mode and call purgatory
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Another round of cleanup for entry[64].S, in particular the program check
handler looks more reasonable now. The code size for the 31 bit kernel
has been reduced by 616 byte and by 528 byte for the 64 bit version.
Even better the code is a bit faster as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch provides the architecture specific part of the s390 kdump
support.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The diagnose 308 call is the prefered method for clearing all ongoing I/O.
Therefore if it is available we use it instead of doing a manual reset.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
The alignment is missing for various global symbols in s390 assembly code.
With a recent gcc and an instruction like stgrl this can lead to a
specification exception if the instruction uses such a mis-aligned address.
Specify the alignment explicitely and while add it define __ALIGN for s390
and use the ENTRY define to save some lines of code.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use asm offsets to make sure the offset defines to struct _lowcore and
its layout don't get out of sync.
Also add a BUILD_BUG_ON() which checks that the size of the structure
is sane.
And while being at it change those sites which use odd casts to access
the current lowcore. These should use S390_lowcore instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Hopefully this will make it more maintainable and less error prone.
Code makes use of search_exception_tables(). Since it calls this
function before the kernel exeception table is sorted, there is an
early call to sort_main_extable().
This way it's easy to use the already present infrastructure of fixup
sections. Also this would allows to easily convert the rest of
head[31|64].S into C code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
