| Age | Commit message (Collapse) | Author |
|---|
|
Now that we have the alpaca, the reg_save_ptr is no longer needed in the
paca. Eradicate all global uses of it and make it static in the iSeries
lpardata.c
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The iSeries HV only needs the first two fields of the paca statically
initialised, so create an alternate paca that contains only those and
switch to our real paca immediately after boot.
This is in order to make the 1024 cpu patches easier since they will no
longer have to statically initialise the pacas for iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The prpmc2800 platform requires a zImage formatted file with an
embedded dtb file. Rename the requested boot image file to
dtbImage.prpmc2800.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform. Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank. This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports. The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device. The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove several unused (or software config only) properties.
Rename marvel node to "system-controller". Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Replace several device node absolute path lookups in the mv64x60
bootwrapper code with lookups by compatible or device_type
properties.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Compatible names should refer to a specific version of the hardware,
without wildcards. Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated. This fixes them. Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The allyesconfig (among others) build was giving this:
In file included from include/linux/gfp.h:4,
from include/linux/slab.h:14,
from include/linux/percpu.h:5,
from include2/asm/time.h:18,
from include2/asm/cputime.h:26,
from include/linux/sched.h:67,
from
arch/powerpc/kernel/asm-offsets.c:17:
include/linux/mmzone.h:791:2: error: #error Allocator MAX_ORDER exceeds SECTION_SIZE
Kconfig options are order depenendent, so move the setting of
FORCE_MAX_ZONEORDER to after the setting of PPC_64K_PAGES. Also add an
explicit !PPC_64K_PAGES.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
If an SLB miss interrupt happens while the RI bit of MSR is zero, we
can't just return, because RI being zero indicates that SRR0/SRR1
potentially had live values in them, and the process of taking an
interrupt overwrites them.
This should never happen, but if it does, we try to print a nice oops
message. That doesn't work, however, because the code at unrecov_slb
assumes that the MMU has been turned on, but we call it with the MMU
off (and have done so since the SLB miss handler was rewritten to run
without turning the MMU on) -- except on iSeries, where everything runs
with the MMU on.
This fixes it by adding the necessary code to turn the MMU on if
necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
This will remove some build warnings and doesn't stop us building any
drivers that we were building previously with these configs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This eliminates a warning in builds that don't define
CONFIG_MEMORY_HOTPLUG.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
A couple of places are duplicating the function of
of_device_is_available; convert them to use it.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This enables the FORCE_MAX_ZONEORDER Kconfig option for all PowerPC
systems. Previously, it was enabled only for 64-bit systems. We also
make the option selectable from the menu, so that the user can specify
different values. This is useful for 32-bit systems that need to
allocate more than 4MB of physically contiguous memory.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We have an assembly version of strncmp for the bootwrapper, but not
for the kernel, so we end up using the C version in the kernel. This
takes the strncmp code from the bootup and copies it to the kernel
proper, adding two instructions so it copes correctly with len==0.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Replace logical "&&" by bit "&" for ISA_SPACE_MASK.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Include the newly added Canyonlands and Yosemite ports in the mutli-board
440 defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
With a multiplatform kernel, once built we always have warp_setup_nand_flash()
called and NDFC probed, no matter what machine we actually run on. This
potentially can cause problems (such as kernel crash), since NDFC is probed at
a warp-predefined address.
Using machine_device_initcall() NAND devices are registered if we run on a warp only.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch changes the "max-frame-size" property to 9000 for all gbit
enabled 4xx boards. All those ports generally support jumbo frames, so
let's give the user a chance to enable it.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch fixes some problems in the Canyonlands 460EX and Glacier 460GT
dts files:
- Add "mdio-device = <&EMAC0>" to all all EMAC's except for EMAC0 itself
(the 460EX/GT only can access the PHY via the EMAC0 instance)
- Add TAH support to Canyonlands dts
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This gets the FEC ethernet driver working again on the lite5200
platform.
The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200. Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B. This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
DTS updates that fix booting problems on mpc5200-based boards:
- change to ethernet reg property
- addition of mdio and phy nodes
- removal of pci node (Motion-Pro board)
Other DTS updates:
- update i2c device tree nodes
- add lpb bus node and flash device (without partitions defined)
- add rtc i2c nodes
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Handling of the proc_dir_entry->count was changed in 2.6.24-rc5.
After this change, the default value for pde->count is 1 and not 0 as
before. Therefore, if we want to check whether our procfs file is
already opened (already in use), we have to check if pde->count is
greater than 2 rather than 1.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
hash_page_sync() takes and releases the low level mmu hash
lock in order to sync with other processors disposing of page
tables. Because that lock can be needed to service hash misses
triggered by interrupt handlers, taking it must be done with
interrupts off. However, hash_page_sync() appears to be called
with interrupts enabled, thus causing occasional deadlocks.
We fix it by making sure hash_page_sync() masks interrupts while
holding the lock.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
A subtle bug sneaked into iSeries recently. On this platform, we must
not normally clear MSR:EE (the hardware external interrupt enable)
except for short periods of time. Taking an interrupt while
soft-disabled doesn't cause us to clear it for example.
The iSeries kernel expects to mostly run with MSR:EE enabled at all
times except in a few exception entry/exit code paths. Thus
local_irq_enable() doesn't check if it needs to hard-enable as it
expects this to be unnecessary on iSeries.
However, hard_irq_disable() _does_ cause MSR:EE to be cleared,
including on iSeries. A call to it was recently added to the
context switch code, thus causing interrupts to become disabled
for a long periods of time, causing the iSeries watchdog to kick
in under some circumstances and other nasty things.
This patch fixes it by making local_irq_enable() properly re-enable
MSR:EE on iSeries. It basically removes a return statement here
to make iSeries use the same code path as everybody else. That does
mean that we might occasionally get spurious decrementer interrupts
but I don't think that matters.
Another option would have been to make hard_irq_disable() a nop
on iSeries but I didn't like it much, in case we have good reasons
to hard-disable.
Part of the patch is fixes to make sure the hard_enabled PACA field
is properly set on iSeries as it used not to be before, since it
was mostly unused.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
A missing break statement in a switch caused cpm2_clk_setup() to initialize
SCC2 instead of SCC1.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch creates a common system reset routine for all 40x and 44x
systems. Previously only a 44x routine existed. But since this system
reset via the debug control register is common for 40x and 44x let's
share this code for all those platforms in ppc4xx_soc.c.
This patch also enables CONFIG_4xx_SOC for all 40x and 44x platforms.
Tested on Kilauea (405EX) and Canyonlands (440EX).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
The patch fixes a bug, where the PESDRn_UTLSET1 register was setup
wrongly resulting in a non working PCIe port 1. With this fix both
PCIe ports work fine again.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Since the arch/powerpc PCI subsystem now does a complete re-assignment of
the resources, we can move from the unconditional PCIe PHY reset to the
conditional version. Now the PHY is only reset, if no link is established yet.
An additional PHY reset (one is already done in U-Boot) leads to problems
with some Atheros PCIe boards and some HP FPGA PCIe designs.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Call dtc from the Makefile instead of the wrapper script so that the dt
blobs can be generated with a simple make invocation.
Using this patch allows board ports to trigger automatic building of .dtb
files by adding them to the image-y target list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
show_mem() has no need to print the amount of free swap space manually
because show_free_areas() does this already and is called by the
former.
The two outputs only differ in text formatting:
printk("Free swap = %lukB\n", ...);
printk("Free swap: %6ldkB\n", ...);
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Old-world powermacs don't set L2CR or L3CR on processor upgrade cards.
This simple patch allows the setting of L3CR via a kernel parameter
(like the existing kernel parameter to set L2CR).
Signed-off-by: Robert Brose <bob@qbjnet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Split the device setup code in ps3_register_repository_device() in two
routines:
1. ps3_setup_static_device(), to handle the setup of static devices in the
PS3 repository, which can be __init,
2. ps3_setup_dynamic_device(), to handle the setup of storage devices that
may appear later in the PS3 repository.
This fixes a few section mismatch warnings.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
WARNING: vmlinux.o(.text+0xb41b0): Section mismatch in reference from the
function .add_memory() to the function .devinit.text:.arch_add_memory()
The function .add_memory() references
the function __devinit .arch_add_memory().
This is often because .add_memory lacks a __devinit
annotation or the annotation of .arch_add_memory is wrong.
arch_add_memory() is also not __devinit on other architectures
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
WARNING: vmlinux.o(.text+0x1e4c0): Section mismatch in reference from the
function .move_device_tree() to the function .init.text:.lmb_alloc_base()
The function .move_device_tree() references
the function __init .lmb_alloc_base().
This is often because .move_device_tree lacks a __init
annotation or the annotation of .lmb_alloc_base is wrong.
move_device_tree() is called from early_init_devtree() only, which is __init
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
If the platform doesn't support hpte_removebolted(), gracefully
return failure rather than success.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
PS3 save power on halt:
- Replace infinite busy loops by smarter loops calling
lv1_pause() to save power.
- Add ps3_halt() and ps3_sys_manager_halt().
- Add __noreturn annotations.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Improve the debugging support of the PS3 bootwraper code:
o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
allow for more debugging code in the overlay.
o Use the dot symbol to set the size of __system_reset_overlay. The
assembler will then emit an error if the overlay code is too big.
o Remove some unused instructions.
o Update the text describing the PS3 bootwrapper overlay.
o Add a check for null pointer writes.
o Change hcall return value from s64.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add a new routine ps3_get_speid() which returns the logical
SPE ID. This ID is needed for profiling support.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Fix a typo bug 'unlikely(x) == y' and add an unlikely() call to
an unlikely code path in the PS3 interrupt routine ps3_get_irq().
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
|
|
The new rtc subsystem conflicts with genrtc so don't enable GENRTC
if RTCLIB is enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
as prescribed in Documentation/powerpc/booting-without-of.txt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
This patch fixes USB malfunctioning on the MPC837xE-RDB boards.
Similar patch has been already applied for the MDS boards:
commit 28b958859206b7010d03129611c2e444898e3ee4
Author: Li Yang <leoli@freescale.com>
Date: Thu Mar 6 18:42:26 2008 +0800
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
