Age | Commit message (Collapse) | Author |
|
NO_IRQ has been == 0 on powerpc for just over ten years (since commit
0ebfff1491ef ("[POWERPC] Add new interrupt mapping core and change
platforms to use it")). It's also 0 on most other arches.
Although it's fairly harmless, every now and then it causes confusion
when a driver is built on powerpc and another arch which doesn't define
NO_IRQ. There's at least 6 definitions of NO_IRQ in drivers/, at least
some of which are to work around that problem.
So we'd like to remove it. This is fairly trivial in the arch code, we
just convert:
if (irq == NO_IRQ) to if (!irq)
if (irq != NO_IRQ) to if (irq)
irq = NO_IRQ; to irq = 0;
return NO_IRQ; to return 0;
And a few other odd cases as well.
At least for now we keep the #define NO_IRQ, because there is driver
code that uses NO_IRQ and the fixes to remove those will go via other
trees.
Note we also change some occurrences in PPC sound drivers, drivers/ps3,
and drivers/macintosh.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pnv_cxl_enable_phb_kernel_api() grabs a reference to the cxl module to
prevent it from being unloaded after the PHB has been switched to CX4
mode. This breaks the build when CONFIG_MODULES=n as module_mutex
doesn't exist.
However, if we don't have modules, we don't need to protect against the
case of the cxl module being unloaded. As such, split the relevant code
out into a function surrounded with #if IS_MODULE(CXL) so we don't try
to compile it if cxl isn't being compiled as a module.
Fixes: 5918dbc9b4ec ("powerpc/powernv: Add support for the cxl kernel api on the real phb")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The Mellanox CX4 in cxl mode uses a hybrid interrupt model, where
interrupts are routed from the networking hardware to the XSL using the
MSIX table, and from there will be transformed back into an MSIX
interrupt using the cxl style interrupts (i.e. using IVTE entries and
ranges to map a PE and AFU interrupt number to an MSIX address).
We want to hide the implementation details of cxl interrupts as much as
possible. To this end, we use a special version of the MSI setup &
teardown routines in the PHB while in cxl mode to allocate the cxl
interrupts and configure the IVTE entries in the process element.
This function does not configure the MSIX table - the CX4 card uses a
custom format in that table and it would not be appropriate to fill that
out in generic code. The rest of the functionality is similar to the
"Full MSI-X mode" described in the CAIA, and this could be easily
extended to support other adapters that use that mode in the future.
The interrupts will be associated with the default context. If the
maximum number of interrupts per context has been limited (e.g. by the
mlx5 driver), it will automatically allocate additional kernel contexts
to associate extra interrupts as required. These contexts will be
started using the same WED that was used to start the default context.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds support for the peer model of the cxl kernel api to the
PowerNV PHB, in which physical function 0 represents the cxl function on
the card (an XSL in the case of the CX4), which other physical functions
will use for memory access and interrupt services. It is referred to as
the peer model as these functions are peers of one another, as opposed
to the Virtual PHB model which forms a hierarchy.
This patch exports APIs to enable the peer mode, check if a PCI device
is attached to a PHB in this mode, and to set and get the peer AFU for
this mode.
The cxl driver will enable this mode for supported cards by calling
pnv_cxl_enable_phb_kernel_api(). This will set a flag in the PHB to note
that this mode is enabled, and switch out it's controller_ops for the
cxl version.
The cxl version of the controller_ops struct implements it's own
versions of the enable_device_hook and release_device to handle
refcounting on the peer AFU and to allocate a default context for the
device.
Once enabled, the cxl kernel API may not be disabled on a PHB. Currently
there is no safe way to disable cxl mode short of a reboot, so until
that changes there is no reason to support the disable path.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The support for using the Mellanox CX4 in cxl mode will require
additions to the PHB code. In preparation for this, move the existing
cxl code out of pci-ioda.c into a separate pci-cxl.c file to keep things
more organised.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|