| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix an existing bug in our user access handling, exposed by one of
the bug fixes we merged this cycle.
- A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
recently added CONFIG_VMAP_STACK.
Thanks to: Christophe Leroy, Guenter Roeck.
* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
powerpc/futex: Fix incorrect user access blocking
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
|
|
The early versions of our kernel user access prevention (KUAP) were
written by Russell and Christophe, and didn't have separate
read/write access.
At some point I picked up the series and added the read/write access,
but I failed to update the usages in futex.h to correctly allow read
and write.
However we didn't notice because of another bug which was causing the
low-level code to always enable read and write. That bug was fixed
recently in commit 1d8f739b07bd ("powerpc/kuap: Fix set direction in
allow/prevent_user_access()").
futex_atomic_cmpxchg_inatomic() is passed the user address as %3 and
does:
1: lwarx %1, 0, %3
cmpw 0, %1, %4
bne- 3f
2: stwcx. %5, 0, %3
Which clearly loads and stores from/to %3. The logic in
arch_futex_atomic_op_inuser() is similar, so fix both of them to use
allow_read_write_user().
Without this fix, and with PPC_KUAP_DEBUG=y, we see eg:
Bug: Read fault blocked by AMR!
WARNING: CPU: 94 PID: 149215 at arch/powerpc/include/asm/book3s/64/kup-radix.h:126 __do_page_fault+0x600/0xf30
CPU: 94 PID: 149215 Comm: futex_requeue_p Tainted: G W 5.5.0-rc7-gcc9x-g4c25df5640ae #1
...
NIP [c000000000070680] __do_page_fault+0x600/0xf30
LR [c00000000007067c] __do_page_fault+0x5fc/0xf30
Call Trace:
[c00020138e5637e0] [c00000000007067c] __do_page_fault+0x5fc/0xf30 (unreliable)
[c00020138e5638c0] [c00000000000ada8] handle_page_fault+0x10/0x30
--- interrupt: 301 at cmpxchg_futex_value_locked+0x68/0xd0
LR = futex_lock_pi_atomic+0xe0/0x1f0
[c00020138e563bc0] [c000000000217b50] futex_lock_pi_atomic+0x80/0x1f0 (unreliable)
[c00020138e563c30] [c00000000021b668] futex_requeue+0x438/0xb60
[c00020138e563d60] [c00000000021c6cc] do_futex+0x1ec/0x2b0
[c00020138e563d90] [c00000000021c8b8] sys_futex+0x128/0x200
[c00020138e563e20] [c00000000000b7ac] system_call+0x5c/0x68
Fixes: de78a9c42a79 ("powerpc: Add a framework for Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: syzbot+e808452bad7c375cbee6@syzkaller-ppc64.appspotmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200207122145.11928-1-mpe@ellerman.id.au
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
|
|
Architectures for which we have hardware walkers of Linux page table
should flush TLB on mmu gather batch allocation failures and batch flush.
Some architectures like POWER supports multiple translation modes (hash
and radix) and in the case of POWER only radix translation mode needs the
above TLBI. This is because for hash translation mode kernel wants to
avoid this extra flush since there are no hardware walkers of linux page
table. With radix translation, the hardware also walks linux page table
and with that, kernel needs to make sure to TLB invalidate page walk cache
before page table pages are freed.
More details in commit d86564a2f085 ("mm/tlb, x86/mm: Support invalidating
TLB caches for RCU_TABLE_FREE")
The changes to sparc are to make sure we keep the old behavior since we
are now removing HAVE_RCU_TABLE_NO_INVALIDATE. The default value for
tlb_needs_table_invalidate is to always force an invalidate and sparc can
avoid the table invalidate. Hence we define tlb_needs_table_invalidate to
false for sparc architecture.
Link: http://lkml.kernel.org/r/20200116064531.483522-3-aneesh.kumar@linux.ibm.com
Fixes: a46cc7a90fd8 ("powerpc/mm/radix: Improve TLB/PWC flushes")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "Fixup page directory freeing", v4.
This is a repost of patch series from Peter with the arch specific changes
except ppc64 dropped. ppc64 changes are added here because we are redoing
the patch series on top of ppc64 changes. This makes it easy to backport
these changes. Only the first 2 patches need to be backported to stable.
The thing is, on anything SMP, freeing page directories should observe the
exact same order as normal page freeing:
1) unhook page/directory
2) TLB invalidate
3) free page/directory
Without this, any concurrent page-table walk could end up with a
Use-after-Free. This is esp. trivial for anything that has software
page-table walkers (HAVE_FAST_GUP / software TLB fill) or the hardware
caches partial page-walks (ie. caches page directories).
Even on UP this might give issues since mmu_gather is preemptible these
days. An interrupt or preempted task accessing user pages might stumble
into the free page if the hardware caches page directories.
This patch series fixes ppc64 and add generic MMU_GATHER changes to
support the conversion of other architectures. I haven't added patches
w.r.t other architecture because they are yet to be acked.
This patch (of 9):
A followup patch is going to make sure we correctly invalidate page walk
cache before we free page table pages. In order to keep things simple
enable RCU_TABLE_FREE even for !SMP so that we don't have to fixup the
!SMP case differently in the followup patch
!SMP case is right now broken for radix translation w.r.t page walk
cache flush. We can get interrupted in between page table free and
that would imply we have page walk cache entries pointing to tables
which got freed already. Michael said "both our platforms that run on
Power9 force SMP on in Kconfig, so the !SMP case is unlikely to be a
problem for anyone in practice, unless they've hacked their kernel to
build it !SMP."
Link: http://lkml.kernel.org/r/20200116064531.483522-2-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
walk_page_range() is going to be allowed to walk page tables other than
those of user space. For this it needs to know when it has reached a
'leaf' entry in the page tables. This information is provided by the
p?d_leaf() functions/macros.
For powerpc p?d_is_leaf() functions already exist. Export them using the
new p?d_leaf() name.
Link: http://lkml.kernel.org/r/20191218162402.45610-7-steven.price@arm.com
Signed-off-by: Steven Price <steven.price@arm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random changes from Ted Ts'o:
"Change /dev/random so that it uses the CRNG and only blocking if the
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (24 commits)
s390x: Mark archrandom.h functions __must_check
powerpc: Mark archrandom.h functions __must_check
powerpc: Use bool in archrandom.h
x86: Mark archrandom.h functions __must_check
linux/random.h: Mark CONFIG_ARCH_RANDOM functions __must_check
linux/random.h: Use false with bool
linux/random.h: Remove arch_has_random, arch_has_random_seed
s390: Remove arch_has_random, arch_has_random_seed
powerpc: Remove arch_has_random, arch_has_random_seed
x86: Remove arch_has_random, arch_has_random_seed
random: remove some dead code of poolinfo
random: fix typo in add_timer_randomness()
random: Add and use pr_fmt()
random: convert to ENTROPY_BITS for better code readability
random: remove unnecessary unlikely()
random: remove kernel.random.read_wakeup_threshold
random: delete code to pull data into pools
random: remove the blocking pool
random: make /dev/random be almost like /dev/urandom
random: ignore GRND_RANDOM in getentropy(2)
...
|
|
Merge the user_access_begin() series from Christophe. This is based on
a commit from Linus that went into v5.5-rc7.
|
|
Pull KVM updates from Paolo Bonzini:
"This is the first batch of KVM changes.
ARM:
- cleanups and corner case fixes.
PPC:
- Bugfixes
x86:
- Support for mapping DAX areas with large nested page table entries.
- Cleanups and bugfixes here too. A particularly important one is a
fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to
exploit the guest kernel, for which the embargo expired today.
- Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
- Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling
hyperthread to read it), which unfortunately is an even bigger
whack-a-mole game than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large
refactoring of vCPU creation that affects all architectures but should
not have any visible effect.
s390 will come next week together with some more x86 patches"
* tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
x86/KVM: Clean up host's steal time structure
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
x86/kvm: Cache gfn to pfn translation
x86/kvm: Introduce kvm_(un)map_gfn()
x86/kvm: Be careful not to clear KVM_VCPU_FLUSH_TLB bit
KVM: PPC: Book3S PR: Fix -Werror=return-type build failure
KVM: PPC: Book3S HV: Release lock on page-out failure path
KVM: arm64: Treat emulated TVAL TimerValue as a signed 32-bit integer
KVM: arm64: pmu: Only handle supported event counters
KVM: arm64: pmu: Fix chained SW_INCR counters
KVM: arm64: pmu: Don't mark a counter as chained if the odd one is disabled
KVM: arm64: pmu: Don't increment SW_INCR if PMCR.E is unset
KVM: x86: Use a typedef for fastop functions
KVM: X86: Add 'else' to unify fastop and execute call path
KVM: x86: inline memslot_valid_for_gpte
KVM: x86/mmu: Use huge pages for DAX-backed files
KVM: x86/mmu: Remove lpage_is_disallowed() check from set_spte()
KVM: x86/mmu: Fold max_mapping_level() into kvm_mmu_hugepage_adjust()
KVM: x86/mmu: Zap any compound page when collapsing sptes
KVM: x86/mmu: Remove obsolete gfn restoration in FNAME(fetch)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx
Pull x86 MPX removal from Dave Hansen:
"MPX requires recompiling applications, which requires compiler
support. Unfortunately, GCC 9.1 is expected to be be released without
support for MPX. This means that there was only a relatively small
window where folks could have ever used MPX. It failed to gain wide
adoption in the industry, and Linux was the only mainstream OS to ever
support it widely.
Support for the feature may also disappear on future processors.
This set completes the process that we started during the 5.4 merge
window when the MPX prctl()s were removed. XSAVE support is left in
place, which allows MPX-using KVM guests to continue to function"
* tag 'mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx:
x86/mpx: remove MPX from arch/x86
mm: remove arch_bprm_mm_init() hook
x86/mpx: remove bounds exception code
x86/mpx: remove build infrastructure
x86/alternatives: add missing insn.h include
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
Second KVM PPC update for 5.6
* Fix compile warning on 32-bit machines
* Fix locking error in secure VM support
|
|
Pull SCSI updates from James Bottomley:
"This series is slightly unusual because it includes Arnd's compat
ioctl tree here:
1c46a2cf2dbd Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Excluding Arnd's changes, this is mostly an update of the usual
drivers: megaraid_sas, mpt3sas, qla2xxx, ufs, lpfc, hisi_sas.
There are a couple of core and base updates around error propagation
and atomicity in the attribute container base we use for the SCSI
transport classes.
The rest is minor changes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (149 commits)
scsi: hisi_sas: Rename hisi_sas_cq.pci_irq_mask
scsi: hisi_sas: Add prints for v3 hw interrupt converge and automatic affinity
scsi: hisi_sas: Modify the file permissions of trigger_dump to write only
scsi: hisi_sas: Replace magic number when handle channel interrupt
scsi: hisi_sas: replace spin_lock_irqsave/spin_unlock_restore with spin_lock/spin_unlock
scsi: hisi_sas: use threaded irq to process CQ interrupts
scsi: ufs: Use UFS device indicated maximum LU number
scsi: ufs: Add max_lu_supported in struct ufs_dev_info
scsi: ufs: Delete is_init_prefetch from struct ufs_hba
scsi: ufs: Inline two functions into their callers
scsi: ufs: Move ufshcd_get_max_pwr_mode() to ufshcd_device_params_init()
scsi: ufs: Split ufshcd_probe_hba() based on its called flow
scsi: ufs: Delete struct ufs_dev_desc
scsi: ufs: Fix ufshcd_probe_hba() reture value in case ufshcd_scsi_add_wlus() fails
scsi: ufs-mediatek: enable low-power mode for hibern8 state
scsi: ufs: export some functions for vendor usage
scsi: ufs-mediatek: add dbg_register_dump implementation
scsi: qla2xxx: Fix a NULL pointer dereference in an error path
scsi: qla1280: Make checking for 64bit support consistent
scsi: megaraid_sas: Update driver version to 07.713.01.00-rc1
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Cleanup of the GOP [graphics output] handling code in the EFI stub
- Complete refactoring of the mixed mode handling in the x86 EFI stub
- Overhaul of the x86 EFI boot/runtime code
- Increase robustness for mixed mode code
- Add the ability to disable DMA at the root port level in the EFI
stub
- Get rid of RWX mappings in the EFI memory map and page tables,
where possible
- Move the support code for the old EFI memory mapping style into its
only user, the SGI UV1+ support code.
- plus misc fixes, updates, smaller cleanups.
... and due to interactions with the RWX changes, another round of PAT
cleanups make a guest appearance via the EFI tree - with no side
effects intended"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
efi/x86: Disable instrumentation in the EFI runtime handling code
efi/libstub/x86: Fix EFI server boot failure
efi/x86: Disallow efi=old_map in mixed mode
x86/boot/compressed: Relax sed symbol type regex for LLVM ld.lld
efi/x86: avoid KASAN false positives when accessing the 1: 1 mapping
efi: Fix handling of multiple efi_fake_mem= entries
efi: Fix efi_memmap_alloc() leaks
efi: Add tracking for dynamically allocated memmaps
efi: Add a flags parameter to efi_memory_map
efi: Fix comment for efi_mem_type() wrt absent physical addresses
efi/arm: Defer probe of PCIe backed efifb on DT systems
efi/x86: Limit EFI old memory map to SGI UV machines
efi/x86: Avoid RWX mappings for all of DRAM
efi/x86: Don't map the entire kernel text RW for mixed mode
x86/mm: Fix NX bit clearing issue in kernel_map_pages_in_pgd
efi/libstub/x86: Fix unused-variable warning
efi/libstub/x86: Use mandatory 16-byte stack alignment in mixed mode
efi/libstub/x86: Use const attribute for efi_is_64bit()
efi: Allow disabling PCI busmastering on bridges during boot
efi/x86: Allow translating 64-bit arguments for mixed mode calls
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The RCU changes in this cycle were:
- Expedited grace-period updates
- kfree_rcu() updates
- RCU list updates
- Preemptible RCU updates
- Torture-test updates
- Miscellaneous fixes
- Documentation updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (69 commits)
rcu: Remove unused stop-machine #include
powerpc: Remove comment about read_barrier_depends()
.mailmap: Add entries for old paulmck@kernel.org addresses
srcu: Apply *_ONCE() to ->srcu_last_gp_end
rcu: Switch force_qs_rnp() to for_each_leaf_node_cpu_mask()
rcu: Move rcu_{expedited,normal} definitions into rcupdate.h
rcu: Move gp_state_names[] and gp_state_getname() to tree_stall.h
rcu: Remove the declaration of call_rcu() in tree.h
rcu: Fix tracepoint tracking RCU CPU kthread utilization
rcu: Fix harmless omission of "CONFIG_" from #if condition
rcu: Avoid tick_dep_set_cpu() misordering
rcu: Provide wrappers for uses of ->rcu_read_lock_nesting
rcu: Use READ_ONCE() for ->expmask in rcu_read_unlock_special()
rcu: Clear ->rcu_read_unlock_special only once
rcu: Clear .exp_hint only when deferred quiescent state has been reported
rcu: Rename some instance of CONFIG_PREEMPTION to CONFIG_PREEMPT_RCU
rcu: Remove kfree_call_rcu_nobatch()
rcu: Remove kfree_rcu() special casing and lazy-callback handling
rcu: Add support for debug_objects debugging for kfree_rcu()
rcu: Add multiple in-flight batches of kfree_rcu() work
...
|
|
Implement user_access_save() and user_access_restore()
On 8xx and radix:
- On save, get the value of the associated special register then
prevent user access.
- On restore, set back the saved value to the associated special
register.
On book3s/32:
- On save, get the value stored in current->thread.kuap and prevent
user access.
- On restore, regenerate address range from the stored value and
reopen read/write access for that range.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/54f2f74938006b33c55a416674807b42ef222068.1579866752.git.christophe.leroy@c-s.fr
|
|
Today, when a function like strncpy_from_user() is called,
the userspace access protection is de-activated and re-activated
for every word read.
By implementing user_access_begin and friends, the protection
is de-activated at the beginning of the copy and re-activated at the
end.
Implement user_access_begin(), user_access_end() and
unsafe_get_user(), unsafe_put_user() and unsafe_copy_to_user()
For the time being, we keep user_access_save() and
user_access_restore() as nops.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/36d4fbf9e56a75994aca4ee2214c77b26a5a8d35.1579866752.git.christophe.leroy@c-s.fr
|
|
In preparation of implementing user_access_begin and friends
on powerpc, the book3s/32 version of prevent_user_access() need
to be prepared for user_access_end().
user_access_end() doesn't provide the address and size which
were passed to user_access_begin(), required by prevent_user_access()
to know which segment to modify.
The list of segments which where unprotected by allow_user_access()
are available in current->kuap. But we don't want prevent_user_access()
to read this all the time, especially everytime it is 0 (for instance
because the access was not a write access).
Implement a special direction named KUAP_CURRENT. In this case only,
the addr and end are retrieved from current->kuap.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/55bcc1f25d8200892a31f67a0b024ff3b816c3cc.1579866752.git.christophe.leroy@c-s.fr
|
|
NULL addr is a user address. Don't waste time checking it. If
someone tries to access it, it will SIGFAULT the same way as for
address 1, so no need to make it special.
The special case is when not doing a write, in that case we want
to drop the entire function. This is now handled by 'dir' param
and not by the nulity of 'to' anymore.
Also make beginning of prevent_user_access() similar
to beginning of allow_user_access(), and tell the compiler
that writing in kernel space or with a 0 length is unlikely
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/85e971223dfe6ace734637db1841678939a76155.1579866752.git.christophe.leroy@c-s.fr
|
|
__builtin_constant_p() always return 0 for pointers, so on RADIX
we always end up opening both direction (by writing 0 in SPR29):
0000000000000170 <._copy_to_user>:
...
1b0: 4c 00 01 2c isync
1b4: 39 20 00 00 li r9,0
1b8: 7d 3d 03 a6 mtspr 29,r9
1bc: 4c 00 01 2c isync
1c0: 48 00 00 01 bl 1c0 <._copy_to_user+0x50>
1c0: R_PPC64_REL24 .__copy_tofrom_user
...
0000000000000220 <._copy_from_user>:
...
2ac: 4c 00 01 2c isync
2b0: 39 20 00 00 li r9,0
2b4: 7d 3d 03 a6 mtspr 29,r9
2b8: 4c 00 01 2c isync
2bc: 7f c5 f3 78 mr r5,r30
2c0: 7f 83 e3 78 mr r3,r28
2c4: 48 00 00 01 bl 2c4 <._copy_from_user+0xa4>
2c4: R_PPC64_REL24 .__copy_tofrom_user
...
Use an explicit parameter for direction selection, so that GCC
is able to see it is a constant:
00000000000001b0 <._copy_to_user>:
...
1f0: 4c 00 01 2c isync
1f4: 3d 20 40 00 lis r9,16384
1f8: 79 29 07 c6 rldicr r9,r9,32,31
1fc: 7d 3d 03 a6 mtspr 29,r9
200: 4c 00 01 2c isync
204: 48 00 00 01 bl 204 <._copy_to_user+0x54>
204: R_PPC64_REL24 .__copy_tofrom_user
...
0000000000000260 <._copy_from_user>:
...
2ec: 4c 00 01 2c isync
2f0: 39 20 ff ff li r9,-1
2f4: 79 29 00 04 rldicr r9,r9,0,0
2f8: 7d 3d 03 a6 mtspr 29,r9
2fc: 4c 00 01 2c isync
300: 7f c5 f3 78 mr r5,r30
304: 7f 83 e3 78 mr r3,r28
308: 48 00 00 01 bl 308 <._copy_from_user+0xa8>
308: R_PPC64_REL24 .__copy_tofrom_user
...
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Spell out the directions, s/KUAP_R/KUAP_READ/ etc.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f4e88ec4941d5facb35ce75026b0112f980086c3.1579866752.git.christophe.leroy@c-s.fr
|
|
At the moment, bad_kuap_fault() reports a fault only if a bad access
to userspace occurred while access to userspace was not granted.
But if a fault occurs for a write outside the allowed userspace
segment(s) that have been unlocked, bad_kuap_fault() fails to
detect it and the kernel loops forever in do_page_fault().
Fix it by checking that the accessed address is within the allowed
range.
Fixes: a68c31fc01ef ("powerpc/32s: Implement Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f48244e9485ada0a304ed33ccbb8da271180c80d.1579866752.git.christophe.leroy@c-s.fr
|
|
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
|
|
Add support of KASAN_VMALLOC on PPC32.
To allow this, the early shadow covering the VMALLOC space
need to be removed once high_memory var is set and before
freeing memblock.
And the VMALLOC area need to be aligned such that boundaries
are covered by a full shadow page.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/031dec5487bde9b2181c8b3c9800e1879cf98c1a.1579024426.git.christophe.leroy@c-s.fr
|
|
In order to ease stack overflow detection, align
stack to 2 * THREAD_SIZE when using VMAP_STACK.
This allows overflow detection using a single bit check.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/60e9ae86b7d2cdcf21468787076d345663648f46.1576916812.git.christophe.leroy@c-s.fr
|
|
To support CONFIG_VMAP_STACK, the kernel has to activate Data MMU
Translation for accessing the stack. Before doing that it must save
SRR0, SRR1 and also DAR and DSISR when relevant, in order to not
loose them in case there is a Data TLB Miss once the translation is
reactivated.
This patch adds fields in thread struct for saving those registers.
It prepares entry_32.S to handle exception entry with
Data MMU Translation enabled and alters EXCEPTION_PROLOG macros to
save SRR0, SRR1, DAR and DSISR then reenables Data MMU.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a775a1fea60f190e0f63503463fb775310a2009b.1576916812.git.christophe.leroy@c-s.fr
|
|
We must not use the pointer output without validating the
success of the random read.
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200110145422.49141-10-broonie@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The generic interface uses bool not int; match that.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200110145422.49141-9-broonie@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
These symbols are currently part of the generic archrandom.h
interface, but are currently unused and can be removed.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200110145422.49141-3-broonie@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Commit a25bd72badfa ("powerpc/mm/radix: Workaround prefetch issue with
KVM") introduced a number of workarounds as coming out of a guest with
the mmu enabled would make the cpu would start running in hypervisor
state with the PID value from the guest. The cpu will then start
prefetching for the hypervisor with that PID value.
In Power9 DD2.2 the cpu behaviour was modified to fix this. When
accessing Quadrant 0 in hypervisor mode with LPID != 0 prefetching will
not be performed. This means that we can get rid of the workarounds for
Power9 DD2.2 and later revisions. Add a new cpu feature
CPU_FTR_P9_RADIX_PREFETCH_BUG to indicate if the workarounds are needed.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191206031722.25781-1-jniethe5@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/rcu
Pull RCU updates from Paul E. McKenney:
- Expedited grace-period updates
- kfree_rcu() updates
- RCU list updates
- Preemptible RCU updates
- Torture-test updates
- Miscellaneous fixes
- Documentation updates
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
'read_barrier_depends()' doesn't exist anymore so stop talking about it.
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
Move the kvm_cpu_{un}init() calls to common PPC code as an intermediate
step towards removing kvm_cpu_{un}init() altogether.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move allocation of all flavors of PPC vCPUs to common PPC code. All
variants either allocate 'struct kvm_vcpu' directly, or require that
the embedded 'struct kvm_vcpu' member be located at offset 0, i.e.
guarantee that the allocation can be directly interpreted as a 'struct
kvm_vcpu' object.
Remove the message from the build-time assertion regarding placement of
the struct, as compatibility with the arch usercopy region is no longer
the sole dependent on 'struct kvm_vcpu' being at offset zero.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
From: Dave Hansen <dave.hansen@linux.intel.com>
MPX is being removed from the kernel due to a lack of support
in the toolchain going forward (gcc).
arch_bprm_mm_init() is used at execve() time. The only non-stub
implementation is on x86 for MPX. Remove the hook entirely from
all architectures and generic code.
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: x86@kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
|
|
As reported by ./scripts/checkpatch.pl --strict:
CHECK: extern prototypes should be avoided in .h files
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/157384145834.181768.944827793193636924.stgit@bahia.lan
|
|
The powerpc PCI code requires that a pci_dn structure exists for all
devices in the system. This is fine for real devices since at boot a pci_dn
is created for each PCI device in the DT and it's fine for hotplugged devices
since the hotplug slot driver will manage the pci_dn's devices in hotplug
slots. For SR-IOV, we need the platform / pcibios to manage the pci_dn for
virtual functions since firmware is unaware of VFs, and they aren't
"hot plugged" in the traditional sense.
Management of the pci_dn is handled by the, poorly named, functions:
add_pci_dev_data() and remove_pci_dev_data(). The entire body of these
functions is #ifdef`ed around CONFIG_PCI_IOV and they cannot be used
in any other context, so make them only available when CONFIG_PCI_IOV
is selected, and rename them to reflect their actual usage rather than
having them masquerade as generic code.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190821062655.19735-2-oohall@gmail.com
|
|
Unlike real PCI slots, opencapi slots are directly associated to
the (virtual) opencapi PHB, there's no intermediate bridge. So when
looking for a slot ID, we must start the search from the device node
itself and not its parent.
Also, the slot ID is not attached to a specific bdfn, so let's build
it from the PHB ID, like skiboot.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-6-fbarrat@linux.ibm.com
|
|
On PPC32, the cache lines have a fixed size known at build time.
Don't read it from the datapage.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/dfa7b35e27e01964fcda84bf1ed8b2b31cf93826.1575273217.git.christophe.leroy@c-s.fr
|
|
__get_datapage() is only a few instructions to retrieve the
address of the page where the kernel stores data to the VDSO.
By inlining this function into its users, a bl/blr pair and
a mflr/mtlr pair is avoided, plus a few reg moves.
The improvement is noticeable (about 55 nsec/call on an 8xx)
vdsotest before the patch:
gettimeofday: vdso: 731 nsec/call
clock-gettime-realtime-coarse: vdso: 668 nsec/call
clock-gettime-monotonic-coarse: vdso: 745 nsec/call
vdsotest after the patch:
gettimeofday: vdso: 677 nsec/call
clock-gettime-realtime-coarse: vdso: 613 nsec/call
clock-gettime-monotonic-coarse: vdso: 690 nsec/call
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c39ef7f3dfa25356b01e211d539671f279086c09.1575273217.git.christophe.leroy@c-s.fr
|
|
Unlike standard powerpc, Powerpc 8xx doesn't have SPRN_DABR, but
it has a breakpoint support based on a set of comparators which
allow more flexibility.
Commit 4ad8622dc548 ("powerpc/8xx: Implement hw_breakpoint")
implemented breakpoints by emulating the DABR behaviour. It did
this by setting one comparator the match 4 bytes at breakpoint address
and the other comparator to match 4 bytes at breakpoint address + 4.
Rewrite 8xx hw_breakpoint to make breakpoints match all addresses
defined by the breakpoint address and length by making full use of
comparators.
Now, comparator E is set to match any address greater than breakpoint
address minus one. Comparator F is set to match any address lower than
breakpoint address plus breakpoint length. Addresses are aligned
to 32 bits.
When the breakpoint range starts at address 0, the breakpoint is set
to match comparator F only. When the breakpoint range end at address
0xffffffff, the breakpoint is set to match comparator E only.
Otherwise the breakpoint is set to match comparator E and F.
At the same time, use registers bit names instead of hardcoded values.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/05105deeaf63bc02151aea2cdeaf525534e0e9d4.1574790198.git.christophe.leroy@c-s.fr
|
|
Selecting CONFIG_PPC_DEBUG_WX only impacts ptdump and pgtable_32/64
init calls. Declaring related functions in asm/pgtable.h implies
rebuilding almost everything.
Move ptdump_check_wx() declaration in mm/mmu_decl.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bf34fd9dca61eadf9a134a9f89ebbc162cfd5f86.1578986011.git.christophe.leroy@c-s.fr
|
|
Commit 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in
the same 0xc range") has a bug in the definition of MIN_USER_CONTEXT.
The result is that the context id used for the vmemmap and the lowest
context id handed out to userspace are the same. The context id is
essentially the process identifier as far as the first stage of the
MMU translation is concerned.
This can result in multiple SLB entries with the same VSID (Virtual
Segment ID), accessible to the kernel and some random userspace
process that happens to get the overlapping id, which is not expected
eg:
07 c00c000008000000 40066bdea7000500 1T ESID= c00c00 VSID= 66bdea7 LLP:100
12 0002000008000000 40066bdea7000d80 1T ESID= 200 VSID= 66bdea7 LLP:100
Even though the user process and the kernel use the same VSID, the
permissions in the hash page table prevent the user process from
reading or writing to any kernel mappings.
It can also lead to SLB entries with different base page size
encodings (LLP), eg:
05 c00c000008000000 00006bde0053b500 256M ESID=c00c00000 VSID= 6bde0053b LLP:100
09 0000000008000000 00006bde0053bc80 256M ESID= 0 VSID= 6bde0053b LLP: 0
Such SLB entries can result in machine checks, eg. as seen on a G5:
Oops: Machine check, sig: 7 [#1]
BE PAGE SIZE=64K MU-Hash SMP NR_CPUS=4 NUMA Power Mac
NIP: c00000000026f248 LR: c000000000295e58 CTR: 0000000000000000
REGS: c0000000erfd3d70 TRAP: 0200 Tainted: G M (5.5.0-rcl-gcc-8.2.0-00010-g228b667d8ea1)
MSR: 9000000000109032 <SF,HV,EE,ME,IR,DR,RI> CR: 24282048 XER: 00000000
DAR: c00c000000612c80 DSISR: 00000400 IRQMASK: 0
...
NIP [c00000000026f248] .kmem_cache_free+0x58/0x140
LR [c088000008295e58] .putname 8x88/0xa
Call Trace:
.putname+0xB8/0xa
.filename_lookup.part.76+0xbe/0x160
.do_faccessat+0xe0/0x380
system_call+0x5c/ex68
This happens with 256MB segments and 64K pages, as the duplicate VSID
is hit with the first vmemmap segment and the first user segment, and
older 32-bit userspace maps things in the first user segment.
On other CPUs a machine check is not seen. Instead the userspace
process can get stuck continuously faulting, with the fault never
properly serviced, due to the kernel not understanding that there is
already a HPTE for the address but with inaccessible permissions.
On machines with 1T segments we've not seen the bug hit other than by
deliberately exercising it. That seems to be just a matter of luck
though, due to the typical layout of the user virtual address space
and the ranges of vmemmap that are typically populated.
To fix it we add 2 to MIN_USER_CONTEXT. This ensures the lowest
context given to userspace doesn't overlap with the VMEMMAP context,
or with the context for INVALID_REGION_ID.
Fixes: 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: Christian Marillat <marillat@debian.org>
Reported-by: Romain Dolbeau <romain@dolbeau.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Account for INVALID_REGION_ID, mostly rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200123102547.11623-1-mpe@ellerman.id.au
|
|
A load on an ESB page returning all 1's means that the underlying
device has invalidated the access to the PQ state of the interrupt
through mmio. It may happen, for example when querying a PHB interrupt
while the PHB is in an error state.
In that case, we should consider the interrupt to be invalid when
checking its state in the irq_get_irqchip_state() handler.
Fixes: da15c03b047d ("powerpc/xive: Implement get_irqchip_state method for XIVE to fix shutdown race")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
[clg: wrote a commit log, introduced XIVE_ESB_INVALID ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200113130118.27969-1-clg@kaod.org
|
|
Implement the H_SVM_INIT_ABORT hcall which the Ultravisor can use to
abort an SVM after it has issued the H_SVM_INIT_START and before the
H_SVM_INIT_DONE hcalls. This hcall could be used when Ultravisor
encounters security violations or other errors when starting an SVM.
Note that this hcall is different from UV_SVM_TERMINATE ucall which
is used by HV to terminate/cleanup an VM that has becore secure.
The H_SVM_INIT_ABORT basically undoes operations that were done
since the H_SVM_INIT_START hcall - i.e page-out all the VM pages back
to normal memory, and terminate the SVM.
(If we do not bring the pages back to normal memory, the text/data
of the VM would be stuck in secure memory and since the SVM did not
go secure, its MSR_S bit will be clear and the VM wont be able to
access its pages even to do a clean exit).
Based on patches and discussion with Paul Mackerras, Ram Pai and
Bharata Rao.
Signed-off-by: Ram Pai <linuxram@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Add 'skip_page_out' parameter to kvmppc_uvmem_drop_pages() so the
callers can specify whetheter or not to skip paging out pages. This
will be needed in a follow-on patch that implements H_SVM_INIT_ABORT
hcall.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.6
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
* tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux: (49 commits)
soc: fsl: qe: remove set but not used variable 'mm_gc'
soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE
soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c
net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32
net/wan/fsl_ucc_hdlc: reject muram offsets above 64K
net/wan/fsl_ucc_hdlc: fix reading of __be16 registers
net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c
soc: fsl: qe: drop pointless check in qe_sdma_init()
soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c
soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path
soc: fsl: qe: drop broken lazy call of cpm_muram_init()
soc: fsl: qe: make cpm_muram_free() ignore a negative offset
soc: fsl: qe: make cpm_muram_free() return void
soc: fsl: qe: change return type of cpm_muram_alloc() to s32
serial: ucc_uart: access __be32 field using be32_to_cpu
serial: ucc_uart: limit brg-frequency workaround to PPC32
serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()
serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32
...
Link: https://lore.kernel.org/r/1578608351-23289-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This implements the tricky tracing and soft irq handling bits in C,
leaving the low level bit to asm.
A functional difference is that this redirects the interrupt exit to
a return stub to execute blr, rather than the lr address itself. This
is probably barely measurable on real hardware, but it keeps the link
stack balanced.
Tested with QEMU.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move power4_fixup_nap back into exceptions-64s.S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190711022404.18132-1-npiggin@gmail.com
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When CONFIG_RELOCATABLE=y is set, VIRT_PHYS_OFFSET is a 64bit variable,
thus __pa() returns as 64bit value.
But when CONFIG_RELOCATABLE=n, __pa() returns 32bit value.
When CONFIG_PHYS_64BIT is set, __pa() should consistently return as
64bit value irrelevant to CONFIG_RELOCATABLE.
So we'd make __pa() consistently return phys_addr_t, which is 64bit
when CONFIG_PHYS_64BIT is set.
Signed-off-by: Bai Yingjie <byj.tea@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200106042957.26494-1-yingjie_bai@126.com
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
