| Age | Commit message (Collapse) | Author |
|---|
|
There were a number of prototypes for functions that no longer
exist. Remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The udbg_16550 code, which we use for our early consoles and debug
backends was fairly messy. Especially for the debug consoles, it
would re-implement the "high level" getc/putc/poll functions for
each access method. It also had code to configure the UART but only
for the straight MMIO method.
This changes it to instead abstract at the register accessor level,
and have the various functions and configuration routines use these.
The result is simpler and slightly smaller code, and free support
for non-MMIO mapped PIO UARTs, which such as the ones that can be
present on a POWER 8 LPC bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch adds a new udbg early debug console which utilises
statically defined input and output buffers stored within the kernel
BSS. It is primarily designed to assist with bring up of new hardware
which may not have a working console but which has a method of
reading/writing kernel memory.
This version incorporates comments made by Ben H (thanks!).
Changes from v1:
- Add memory barriers.
- Ensure updating of read/write positions is atomic.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The last user of udbg_read() was removed in 2005, in commit fca5dcd
"Simplify and clean up the xmon terminal I/O".
Given we haven't needed it for 7 years we can probably drop it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
|
|
This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.
On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.
On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:
hvc0 : network console (raw protocol)
hvc1 : serial port S1 (hvsi)
hvc2 : serial port S2 (hvsi)
Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add a new udbg driver for the PS3 gelic Ehthernet device.
This driver shares only a few stucture and constant definitions with the
gelic Ethernet device driver, so is implemented as a stand-alone driver
with no dependencies on the gelic Ethernet device driver.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The ePAPR embedded hypervisor specification provides an API for "byte
channels", which are serial-like virtual devices for sending and receiving
streams of bytes. This driver provides Linux kernel support for byte
channels via three distinct interfaces:
1) An early-console (udbg) driver. This provides early console output
through a byte channel. The byte channel handle must be specified in a
Kconfig option.
2) A normal console driver. Output is sent to the byte channel designated
for stdout in the device tree. The console driver is for handling kernel
printk calls.
3) A tty driver, which is used to handle user-space input and output. The
byte channel used for the console is designated as the default tty.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On pseries machines, consoles are provided by the hypervisor using
a low level get_chars/put_chars type interface. However, this is
really just a transport to the service processor which implements
them either as "raw" console (networked consoles, HMC, ...) or as
"hvsi" serial ports.
The later is a simple packet protocol on top of the raw character
interface that is supposed to convey additional "serial port" style
semantics. In practice however, all it does is provide a way to
read the CD line and set/clear our DTR line, that's it.
We currently implement the "raw" protocol as an hvc console backend
(/dev/hvcN) and the "hvsi" protocol using a separate tty driver
(/dev/hvsi0).
However this is quite impractical. The arbitrary difference between
the two type of devices has been a major source of user (and distro)
confusion. Additionally, there's an additional mini -hvsi implementation
in the pseries platform code for our low level debug console and early
boot kernel messages, which means code duplication, though that low
level variant is impractical as it's incapable of doing the initial
protocol negociation to establish the link to the FSP.
This essentially replaces the dedicated hvsi driver and the platform
udbg code completely by extending the existing hvc_vio backend used
in "raw" mode so that:
- It now supports HVSI as well
- We add support for hvc backend providing tiocm{get,set}
- It also provides a udbg interface for early debug and boot console
This is overall less code, though this will only be obvious once we
remove the old "hvsi" driver, which is still available for now. When
the old driver is enabled, the new code still kicks in for the low
level udbg console, replacing the old mini implementation in the platform
code, it just doesn't provide the higher level "hvc" interface.
In addition to producing generally simler code, this has several benefits
over our current situation:
- The user/distro only has to deal with /dev/hvcN for the hypervisor
console, avoiding all sort of confusion that has plagued us in the past
- The tty, kernel and low level debug console all use the same code
base which supports the full protocol establishment process, thus the
console is now available much earlier than it used to be with the
old HVSI driver. The kernel console works much earlier and udbg is
available much earlier too. Hackers can enable a hard coded very-early
debug console as well that works with HVSI (previously that was only
supported for the "raw" mode).
I've tried to keep the same semantics as hvsi relative to how I react
to things like CD changes, with some subtle differences though:
- I clear DTR on close if HUPCL is set
- Current hvsi triggers a hangup if it detects a up->down transition
on CD (you can still open a console with CD down). My new implementation
triggers a hangup if the link to the FSP is severed, and severs it upon
detecting a up->down transition on CD.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add support for using the USB Gecko adapter as an early debugging
console on the Nintendo GameCube and Wii video game consoles.
The USB Gecko is a 3rd party memory card interface adapter that provides
a EXI (External Interface) to USB serial converter.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
When the console is on a serial port to be driven by serial8250, a
character can be lost from the end of the first line in the two-line
sequence
serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 42) is a 16550A
console handover: boot [udbg0] -> real [ttyS0]
This happens because udbg_puts or udbg_write stuff the last byte of
the line into the Tx FIFO and return, whereupon the serial8250
initialization code immediately empties that FIFO. The fix: udbg_puts
and udbg_write now wait for the Tx FIFO to clear before returning.
This delays the system by one additional serial frame time for each
line written by udbg, but the effect is not noticeable, a cumulative
17 milliseconds for 200 lines of early printk output at 115200 baud.
Also, the routines in udbg_16550.c now emit CRLF instead of LFCR.
Linux makes a point of emitting CRLF because, when serial output is
captured to a file, LFCR sequences can confuse text editors. See
http://lkml.org/lkml/2006/2/4/50 for some history.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
