| Age | Commit message (Collapse) | Author |
|---|
|
These were introduced in commit 25ae3a0739c6 ("[POWERPC] mpc512x: Add
MPC512x PSC support to MPC52xx psc driver") and never used. Moreover
according to the datasheet[1] MEMERROR is bit 25 (0x40) and ORERR is
bit 27 (0x10).
[1] MPC5125RM Rev. 2; 11/2009
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
The register layout of the PSC devices differ between MPC5121 and
MPC5125, but the registers are named nearly identical and their purpose
is similar enough ("freescale identical") such that substituting
mpc52xx_psc by mpc5125_psc is nearly enough to make the driver work on
MPC5125. To keep supporting MPC5121 this patch introduces a cpp
macro to select the right struct that defines the register layout.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add MPC5125 PSC register layout structure, MPC5125 specific
psc_ops function set and the compatible string.
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Work around a silicon bug in the ac97 reset functionality of the
mpc5200(b). The implementation of the ac97 "cold" reset is flawed.
If the sync and output lines are high when reset is asserted the
attached ac97 device may go into test mode. Avoid this by
reconfiguring the psc to gpio mode and generating the reset manually.
From MPC5200B User's Manual:
"Some AC97 devices goes to a test mode, if the Sync line is high
during the Res line is low (reset phase). To avoid this behavior the
Sync line must be also forced to zero during the reset phase. To do
that, the pin muxing should switch to GPIO mode and the GPIO control
register should be used to control the output lines."
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
MPC5121 has 12 PSC devices. Enable UART support for all of
them by defining the number of max. PSCs depending on
selection of PPC_MPC512x platform support.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add a few more mpc5200 PSC defines. More bit fields defines for mpc5200
PSC registers.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add RTS/CTS-support for the PSC of the MPC5200B. Tested with a Phytec
MPC5200B-IO.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
