| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
|
|
This modifies the IP32 (SGI O2) platform and reset code to utilize the new
rtc-ds1685 driver. The old mc146818rtc.h header is removed and ip32_defconfig
is updated as well.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions. COMPAT definitions retain their
overrides and the remaining definitions were identical.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Here is the first round of kbuild changes for v4.1-rc1:
- kallsyms fix for ARM and cleanup
- make dep(end) removed (developers have no sense of nostalgia these
days...)
- include Makefiles by relative path
- stop useless rebuilds of asm-offsets.h and bounds.h"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: kallsyms: drop special handling of pre-3.0 GCC symbols
Kbuild: kallsyms: ignore veneers emitted by the ARM linker
kbuild: ia64: use $(src)/Makefile.gate rather than particular path
kbuild: include $(src)/Makefile rather than $(obj)/Makefile
kbuild: use relative path more to include Makefile
kbuild: use relative path to include Makefile
kbuild: do not add $(bounds-file) and $(offsets-file) to targets
kbuild: remove warning about "make depend"
kbuild: Don't reset timestamps in include/generated if not needed
|
|
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.1:
New interfaces:
- user-space interface for AEAD
- user-space interface for RNG (i.e., pseudo RNG)
New hashes:
- ARMv8 SHA1/256
- ARMv8 AES
- ARMv8 GHASH
- ARM assembler and NEON SHA256
- MIPS OCTEON SHA1/256/512
- MIPS img-hash SHA1/256 and MD5
- Power 8 VMX AES/CBC/CTR/GHASH
- PPC assembler AES, SHA1/256 and MD5
- Broadcom IPROC RNG driver
Cleanups/fixes:
- prevent internal helper algos from being exposed to user-space
- merge common code from assembly/C SHA implementations
- misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (169 commits)
crypto: arm - workaround for building with old binutils
crypto: arm/sha256 - avoid sha256 code on ARMv7-M
crypto: x86/sha512_ssse3 - move SHA-384/512 SSSE3 implementation to base layer
crypto: x86/sha256_ssse3 - move SHA-224/256 SSSE3 implementation to base layer
crypto: x86/sha1_ssse3 - move SHA-1 SSSE3 implementation to base layer
crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer
crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer
crypto: arm/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer
crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer
crypto: arm/sha1-ce - move SHA-1 ARMv8 implementation to base layer
crypto: arm/sha1_neon - move SHA-1 NEON implementation to base layer
crypto: arm/sha1 - move SHA-1 ARM asm implementation to base layer
crypto: sha512-generic - move to generic glue implementation
crypto: sha256-generic - move to generic glue implementation
crypto: sha1-generic - move to generic glue implementation
crypto: sha512 - implement base layer for SHA-512
crypto: sha256 - implement base layer for SHA-256
crypto: sha1 - implement base layer for SHA-1
crypto: api - remove instance when test failed
crypto: api - Move alg ref count init to crypto_check_alg
...
|
|
The arch_randomize_brk() function is used on several architectures,
even those that don't support ET_DYN ASLR. To avoid bulky extern/#define
tricks, consolidate the support under CONFIG_ARCH_HAS_ELF_RANDOMIZE for
the architectures that support it, while still handling CONFIG_COMPAT_BRK.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes the "offset2lib" weakness in ASLR for arm, arm64, mips,
powerpc, and x86. The problem is that if there is a leak of ASLR from
the executable (ET_DYN), it means a leak of shared library offset as
well (mmap), and vice versa. Further details and a PoC of this attack
is available here:
http://cybersecurity.upv.es/attacks/offset2lib/offset2lib.html
With this patch, a PIE linked executable (ET_DYN) has its own ASLR
region:
$ ./show_mmaps_pie
54859ccd6000-54859ccd7000 r-xp ... /tmp/show_mmaps_pie
54859ced6000-54859ced7000 r--p ... /tmp/show_mmaps_pie
54859ced7000-54859ced8000 rw-p ... /tmp/show_mmaps_pie
7f75be764000-7f75be91f000 r-xp ... /lib/x86_64-linux-gnu/libc.so.6
7f75be91f000-7f75beb1f000 ---p ... /lib/x86_64-linux-gnu/libc.so.6
7f75beb1f000-7f75beb23000 r--p ... /lib/x86_64-linux-gnu/libc.so.6
7f75beb23000-7f75beb25000 rw-p ... /lib/x86_64-linux-gnu/libc.so.6
7f75beb25000-7f75beb2a000 rw-p ...
7f75beb2a000-7f75beb4d000 r-xp ... /lib64/ld-linux-x86-64.so.2
7f75bed45000-7f75bed46000 rw-p ...
7f75bed46000-7f75bed47000 r-xp ...
7f75bed47000-7f75bed4c000 rw-p ...
7f75bed4c000-7f75bed4d000 r--p ... /lib64/ld-linux-x86-64.so.2
7f75bed4d000-7f75bed4e000 rw-p ... /lib64/ld-linux-x86-64.so.2
7f75bed4e000-7f75bed4f000 rw-p ...
7fffb3741000-7fffb3762000 rw-p ... [stack]
7fffb377b000-7fffb377d000 r--p ... [vvar]
7fffb377d000-7fffb377f000 r-xp ... [vdso]
The change is to add a call the newly created arch_mmap_rnd() into the
ELF loader for handling ET_DYN ASLR in a separate region from mmap ASLR,
as was already done on s390. Removes CONFIG_BINFMT_ELF_RANDOMIZE_PIE,
which is no longer needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When an architecture fully supports randomizing the ELF load location,
a per-arch mmap_rnd() function is used to find a randomized mmap base.
In preparation for randomizing the location of ET_DYN binaries
separately from mmap, this renames and exports these functions as
arch_mmap_rnd(). Additionally introduces CONFIG_ARCH_HAS_ELF_RANDOMIZE
for describing this feature on architectures that support it
(which is a superset of ARCH_BINFMT_ELF_RANDOMIZE_PIE, since s390
already supports a separated ET_DYN ASLR from mmap ASLR without the
ARCH_BINFMT_ELF_RANDOMIZE_PIE logic).
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In preparation for splitting out ET_DYN ASLR, extract the mmap ASLR
selection into a separate function.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We would want to use number of page table level to define mm_struct.
Let's expose it as CONFIG_PGTABLE_LEVELS.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq core updates from Thomas Gleixner:
"Managerial summary:
Core code:
- final removal of IRQF_DISABLED
- new state save/restore functions for virtualization support
- wakeup support for stacked irqdomains
- new function to solve the netpoll synchronization problem
irqchips:
- new driver for STi based devices
- new driver for Vybrid MSCM
- massive cleanup of the GIC driver by moving the GIC-addons to
stacked irqdomains
- the usual pile of fixes and updates to the various chip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
irqchip: GICv3: Add support for irq_[get, set]_irqchip_state()
irqchip: GIC: Add support for irq_[get, set]_irqchip_state()
genirq: Allow the irqchip state of an IRQ to be save/restored
genirq: MSI: Fix freeing of unallocated MSI
irqchip: renesas-irqc: Add wake-up support
irqchip: armada-370-xp: Allow using wakeup source
irqchip: mips-gic: Add new functions to start/stop the GIC counter
irqchip: tegra: Add Tegra210 support
irqchip: digicolor: Move digicolor_set_gc to init section
irqchip: renesas-irqc: Add functional clock to bindings
irqchip: renesas-irqc: Add minimal runtime PM support
irqchip: renesas-irqc: Add more register documentation
DT: exynos: update PMU binding
ARM: exynos4/5: convert pmu wakeup to stacked domains
irqchip: gic: Don't complain in gic_get_cpumask() if UP system
ARM: zynq: switch from gic_arch_extn to gic_set_irqchip_flags
ARM: ux500: switch from gic_arch_extn to gic_set_irqchip_flags
ARM: shmobile: remove use of gic_arch_extn.irq_set_wake
irqchip: gic: Add an entry point to set up irqchip flags
ARM: omap: convert wakeupgen to stacked domains
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Read capability list as dwords, not bytes (Sean O. Stalley)
Resource management
- Don't check for PNP overlaps with unassigned PCI BARs (Bjorn Helgaas)
- Mark invalid BARs as unassigned (Bjorn Helgaas)
- Show driver, BAR#, and resource on pci_ioremap_bar() failure (Bjorn Helgaas)
- Fail pci_ioremap_bar() on unassigned resources (Bjorn Helgaas)
- Assign resources before drivers claim devices (Yijing Wang)
- Claim bus resources before pci_bus_add_devices() (Yijing Wang)
Power management
- Optimize device state transition delays (Aaron Lu)
- Don't clear ASPM bits when the FADT declares it's unsupported (Matthew Garrett)
Virtualization
- Add ACS quirks for Intel 1G NICs (Alex Williamson)
IOMMU
- Add ptr to OF node arg to of_iommu_configure() (Murali Karicheri)
- Move of_dma_configure() to device.c to help re-use (Murali Karicheri)
- Fix size when dma-range is not used (Murali Karicheri)
- Add helper functions pci_get[put]_host_bridge_device() (Murali Karicheri)
- Add of_pci_dma_configure() to update DMA configuration (Murali Karicheri)
- Update DMA configuration from DT (Murali Karicheri)
- dma-mapping: limit IOMMU mapping size (Murali Karicheri)
- Calculate device DMA masks based on DT dma-range size (Murali Karicheri)
ARM Versatile host bridge driver
- Check for devm_ioremap_resource() failures (Jisheng Zhang)
Broadcom iProc host bridge driver
- Add Broadcom iProc PCIe driver (Ray Jui)
Marvell MVEBU host bridge driver
- Add suspend/resume support (Thomas Petazzoni)
Renesas R-Car host bridge driver
- Fix position of MSI enable bit (Nobuhiro Iwamatsu)
- Write zeroes to reserved PCIEPARL bits (Nobuhiro Iwamatsu)
- Change PCIEPARL and PCIEPARH to PCIEPALR and PCIEPAUR (Nobuhiro Iwamatsu)
- Verify that mem_res is 64K-aligned (Nobuhiro Iwamatsu)
Samsung Exynos host bridge driver
- Fix INTx enablement statement termination error (Jaehoon Chung)
Miscellaneous
- Make a shareable UUID for PCI firmware ACPI _DSM (Aaron Lu)
- Clarify policy for vendor IDs in pci.txt (Michael S. Tsirkin)"
* tag 'pci-v4.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (36 commits)
PCI: Read capability list as dwords, not bytes
PCI: layerscape: Simplify platform_get_resource_byname() failure checking
PCI: keystone: Don't dereference possible NULL pointer
PCI: versatile: Check for devm_ioremap_resource() failures
PCI: Don't clear ASPM bits when the FADT declares it's unsupported
PCI: Clarify policy for vendor IDs in pci.txt
PCI/ACPI: Optimize device state transition delays
PCI: Export pci_find_host_bridge() for use inside PCI core
PCI: Make a shareable UUID for PCI firmware ACPI _DSM
PCI: Fix typo in Thunderbolt kernel message
PCI: exynos: Fix INTx enablement statement termination error
PCI: iproc: Add Broadcom iProc PCIe support
PCI: iproc: Add DT docs for Broadcom iProc PCIe driver
PCI: Export symbols required for loadable host driver modules
PCI: Add ACS quirks for Intel 1G NICs
PCI: mvebu: Add suspend/resume support
PCI: Cleanup control flow
sparc/PCI: Claim bus resources before pci_bus_add_devices()
PCI: Assign resources before drivers claim devices (pci_scan_root_bus())
PCI: Fail pci_ioremap_bar() on unassigned resources
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Ingo Molnar:
"The main changes in this cycle were:
- clockevents state machine cleanups and enhancements (Viresh Kumar)
- clockevents broadcast notifier horror to state machine conversion
and related cleanups (Thomas Gleixner, Rafael J Wysocki)
- clocksource and timekeeping core updates (John Stultz)
- clocksource driver updates and fixes (Ben Dooks, Dmitry Osipenko,
Hans de Goede, Laurent Pinchart, Maxime Ripard, Xunlei Pang)
- y2038 fixes (Xunlei Pang, John Stultz)
- NMI-safe ktime_get_raw_fast() and general refactoring of the clock
code, in preparation to perf's per event clock ID support (Peter
Zijlstra)
- generic sched/clock fixes, optimizations and cleanups (Daniel
Thompson)
- clockevents cpu_down() race fix (Preeti U Murthy)"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
timers/PM: Drop unnecessary braces from tick_freeze()
timers/PM: Fix up tick_unfreeze()
timekeeping: Get rid of stale comment
clockevents: Cleanup dead cpu explicitely
clockevents: Make tick handover explicit
clockevents: Remove broadcast oneshot control leftovers
sched/idle: Use explicit broadcast oneshot control function
ARM: Tegra: Use explicit broadcast oneshot control function
ARM: OMAP: Use explicit broadcast oneshot control function
intel_idle: Use explicit broadcast oneshot control function
ACPI/idle: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast oneshot control function
x86/amd/idle, clockevents: Use explicit broadcast oneshot control functions
clockevents: Provide explicit broadcast oneshot control functions
clockevents: Remove the broadcast control leftovers
ARM: OMAP: Use explicit broadcast control function
intel_idle: Use explicit broadcast control function
cpuidle: Use explicit broadcast control function
ACPI/processor: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast control function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core locking changes from Ingo Molnar:
"Main changes:
- jump label asm preparatory work for PowerPC (Anton Blanchard)
- rwsem optimizations and cleanups (Davidlohr Bueso)
- mutex optimizations and cleanups (Jason Low)
- futex fix (Oleg Nesterov)
- remove broken atomicity checks from {READ,WRITE}_ONCE() (Peter
Zijlstra)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
powerpc, jump_label: Include linux/jump_label.h to get HAVE_JUMP_LABEL define
jump_label: Allow jump labels to be used in assembly
jump_label: Allow asm/jump_label.h to be included in assembly
locking/mutex: Further simplify mutex_spin_on_owner()
locking: Remove atomicy checks from {READ,WRITE}_ONCE
locking/rtmutex: Rename argument in the rt_mutex_adjust_prio_chain() documentation as well
locking/rwsem: Fix lock optimistic spinning when owner is not running
locking: Remove ACCESS_ONCE() usage
locking/rwsem: Check for active lock before bailing on spinning
locking/rwsem: Avoid deceiving lock spinners
locking/rwsem: Set lock ownership ASAP
locking/rwsem: Document barrier need when waking tasks
locking/futex: Check PF_KTHREAD rather than !p->mm to filter out kthreads
locking/mutex: Refactor mutex_spin_on_owner()
locking/mutex: In mutex_spin_on_owner(), return true when owner changes
|
|
|
|
|
|
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Commit 32098ec7bcba ("MIPS: Makefile: Move the ASEs checks after
setting the core's CFLAGS") re-arranged the MIPS ASE detection code
and also added the current cflags to the detection logic. However,
this introduced a few bugs. First of all, the mips-cflags should not
be quoted since that ends up being passed as a string to subsequent
commands leading to broken detection from the cc-option-* tools.
Moreover, in order to avoid duplicating the cflags-y because of how
cc-option works, we rework the logic so we pass only those cflags which
are needed by the selected ASE. Finally, fix some typos resulting in MSA
not being detected correctly.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: Commit 32098ec7bcba ("MIPS: Makefile: Move the ASEs checks after setting the core's CFLAGS")
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9661/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Set good default FPU flags (FR0) for O32 binaries similar to what the
kernel does for the N64/N32 ones. This also fixes a regression
introduced in commit 46490b572544 ("MIPS: kernel: elf: Improve the
overall ABI and FPU mode checks") when MIPS_O32_FP64_SUPPORT is
disabled. In that case, the mips_set_personality_fp() did not set the
FPU mode at all because it assumed that the FPU mode was already set
properly. That led to O32 userland problems.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reported-by: Mans Rullgard <mans@mansr.com>
Fixes: 46490b572544 ("MIPS: kernel: elf: Improve the overall ABI and FPU mode checks")
Tested-by: Mans Rullgard <mans@mansr.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/9344/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Since the day of adding this code it was broken. We were iterating over
a wrong array and checking for wrong NVRAM entry.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/9654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A 64-bit build for Malta produces far too many build problems
when SMP/CPS is selected. Moreover, there is currently no 64-bit
product with SMP/CPS so we disable SMP/CPS when building for
64-bit until it is properly supported.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8573/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We found that TLB mismatch not only happens after kernel resume, but
also happens during snapshot restore. So move it to the beginning of
swsusp_arch_suspend().
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: <stable@vger.kernel.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9621/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If we have an FPU, enroll ourselves in the FPU-full mask.
Matching the MT_SMP and CMP implementations of smp_setup.
Signed-off-by: Niklas Cassel <niklass@axis.com>
Cc: paul.burton@imgtec.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The lose_fpu() function only disables the FPU in CP0_Status.CU1 if the
FPU is in use and MSA isn't enabled.
This isn't necessarily a problem because KSTK_STATUS(current), the
version of CP0_Status stored on the kernel stack on entry from user
mode, does always get updated and gets restored when returning to user
mode, but I don't think it was intended, and it is inconsistent with the
case of only the FPU being in use. Sometimes leaving the FPU enabled may
also mask kernel bugs where FPU operations are executed when the FPU
might not be enabled.
So lets disable the FPU in the MSA case too.
Fixes: 33c771ba5c5d ("MIPS: save/disable MSA in lose_fpu")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A driver was added in commit 5433acd81e87 ("MIPS: ralink: add illegal access
driver") without the Kconfig section being added. Fix this by adding the symbol
to the Kconfig file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9299/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A wrong symbol is referenced by commit 187c26ddf0b2 ("MIPS: ralink: add rt2880
pci driver"). Fix this by changing it to the correct symbol.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9298/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
memsize denotes the amount of RAM we can access from kseg{0,1} and
that should be up to 256M. In case the bootloader reports a value
higher than that (perhaps reporting all the available RAM) it's best
if we fix it ourselves and just warn the user about that. This is
usually a problem with the bootloader and/or its environment.
[ralf@linux-mips.org: Remove useless parens as suggested bei Sergei.
Reformat long pr_warn statement to fit into 80 column limit.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
For a discussion, see http://patchwork.linux-mips.org/patch/9539/.
This reverts commit 625c0a21700bdb90844d926a1508a17a77e369c9.
|
|
This is no longer needed with the fixed, new and improved definition
of cpu_has_mips_r2_exec_hazard in <asm/cpu-features.h>.
For a discussion, see http://patchwork.linux-mips.org/patch/9539/.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Returns a non-zero value if the current processor implementation requires
an IHB instruction to deal with an instruction hazard as per MIPS R2
architecture specification, zero otherwise.
For a discussion, see http://patchwork.linux-mips.org/patch/9539/.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 6ebb496ffc7e("MIPS: kernel: entry.S: Add MIPS R6 related
definitions") added the MIPSR6 definition but it did not update the
ISA level of the actual assembly code so a pre-MIPSR6 jr.hb instruction
was generated instead. Fix this by using the MISP_ISA_LEVEL_RAW macro.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 6ebb496ffc7e("MIPS: kernel: entry.S: Add MIPS R6 related definitions")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9386/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 5753762cbd1c("MIPS: asm: spinlock: Replace "sub" instruction
with "addiu") replaced the "sub" instruction with addiu but it did
not update the immediate value in the R10000_LLSC_WAR case.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 5753762cbd1c("MIPS: asm: spinlock: Replace "sub" instruction with "addiu"")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9385/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 934c79231c1b("MIPS: asm: r4kcache: Add MIPS R6 cache unroll
functions") added support for MIPS R6 cache flushes but it used the
wrong base address register to perform the flushes so the same lines
were flushed over and over. Moreover, replace the "addiu" instructions
with LONG_ADDIU so the correct base address is calculated for 64-bit
cores.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 934c79231c1b("MIPS: asm: r4kcache: Add MIPS R6 cache unroll functions")
Cc: linux-mips@linux-mips.org
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9384/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit b0a668fb2038 ("MIPS: kernel: mips-r2-to-r6-emul: Add R2 emulator
for MIPS R6") added the mips r2-to-r6 emulator so an R2 userland can be
executed on R6 kernels. This needed both build time and runtime support.
The runtime support needed the "mipsr2emu" kernel parameter instead of
the "mipsr2emul" listed in the Kconfig help message.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: b0a668fb2038 ("MIPS: kernel: mips-r2-to-r6-emul: Add R2 emulator for MIPS R6")
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9504/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When emulating a regular lh/lw/lhu/sh/sw we need to use the appropriate
instruction if we are in EVA mode. This is necessary for userspace
applications which trigger alignment exceptions. In such case, the
userspace load/store instruction needs to be emulated with the correct
eva/non-eva instruction by the kernel emulator.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: c1771216ab48 ("MIPS: kernel: unaligned: Handle unaligned accesses for EVA")
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9503/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
It's best to surround such complex macros with do {} while statements
so they can appear as independent logical blocks when used within other
control blocks.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9502/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit c1771216ab48 ("MIPS: kernel: unaligned: Handle unaligned
accesses for EVA") allowed unaligned accesses to be emulated for
EVA. However, when emulating regular load/store unaligned accesses,
we need to use the appropriate "address space" instructions for that.
Previously, an unaligned load/store instruction in kernel space would
have used the corresponding EVA instructions to emulate it which led to
segmentation faults because of the address translation that happens
with EVA instructions. This is now fixed by using the EVA instruction
only when emulating EVA unaligned accesses.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: c1771216ab48 ("MIPS: kernel: unaligned: Handle unaligned accesses for EVA")
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9501/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Introduce new macros for kernel load/store variants which will be
used to perform regular kernel space load/store operations in EVA
mode.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9500/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Update to the SATA PHY initialization. This is needed for SATA detection
to succeed in all configurations.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fix PCI interrupt mapping for DSR1000N. This will get the PCI slot
interrupts working. The mapping is based on D-Link GPL tarball.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
udelay() in PCI/PCIe read/write callbacks cause 30ms IRQ latency on Octeon
platforms because these operations are called from PCI_OP_READ() and
PCI_OP_WRITE() under raw_spin_lock_irqsave().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney@cavium.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mathias <mathias.rulf@nokia.com>
Patchwork: https://patchwork.linux-mips.org/patch/9576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Wrap asm/jump_label.h for all archs with #ifndef __ASSEMBLY__.
Since these are kernel only headers, we don't need #ifdef
__KERNEL__ so can simplify things a bit.
If an architecture wants to use jump labels in assembly, it
will still need to define a macro to create the __jump_table
entries (see ARCH_STATIC_BRANCH in the powerpc asm/jump_label.h
for an example).
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: benh@kernel.crashing.org
Cc: catalin.marinas@arm.com
Cc: davem@davemloft.net
Cc: heiko.carstens@de.ibm.com
Cc: jbaron@akamai.com
Cc: linux@arm.linux.org.uk
Cc: linuxppc-dev@lists.ozlabs.org
Cc: liuj97@gmail.com
Cc: mgorman@suse.de
Cc: mmarek@suse.cz
Cc: mpe@ellerman.id.au
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: rostedt@goodmis.org
Cc: schwidefsky@de.ibm.com
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1428551492-21977-1-git-send-email-anton@samba.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Broadcom BCM63xx DSL SoCs utilize BMIPS CPUs, and as such are required
to perform a read-ahead cache flush after a DMA transfer. Utilize
asm/bmips.h to provide a plat_post_dma_flush_hook, and
mach-generic/dma-coherence.h for everything else.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/9726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Instead of having platforms to copy the entirety of
mach-generic/dma-coherence.h, check whether these platforms have already
defined a plat_post_dma_flush hook, and if not, provide an inline stub.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/9725/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
arch/mips/include/asm/mach-bmips/dma-coherence.h contains the
plat_post_dma_flush implementation which is not specific to mach-bmips,
but required for all BMIPS-based systems.
Move plat_post_dma_flush to arch/mips/include/asm/bmips.h, rename it to
bmips_post_dma_flush such that other platforms like bcm63xx can utilize
it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/9724/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
conflict with pending GIC changes.
Conflicts:
drivers/usb/isp1760/isp1760-core.c
|
