| Age | Commit message (Collapse) | Author |
|---|
|
There is an additional MIIM (MDIO) bus in this SoC so let's declare it
in the dtsi.
This bus requires GPIO 14 and 15 pins that need to be muxed. There is no
support for internal PHY reset on this bus on the contrary of MIIM0 so
there is only one register address space and not two.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20014/
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: thomas.petazzoni@bootlin.com
|
|
The length of memory address space for MIIM0 is from 0x7107009c to
0x710700bf included which is 36 bytes long in decimal, or 0x24 bytes in
hexadecimal and not 0x36.
Fixes: 49b031690abe ("MIPS: mscc: Add switch to ocelot")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20013/
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: thomas.petazzoni@bootlin.com
|
|
The RTC definitions were moved to the driver, remove them from the platform
header.
[paul.burton@mips.com:
- Also remove the unused tx4939_rtcptr which would use struct
tx4939_rtc_reg if it were ever expanded.]
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20024/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
|
|
The ar724x pci driver expects the PCIe controller to be brought out of
reset by the bootloader.
At least the AVM Fritz 300E bootloader doesn't take care of releasing
the different PCIe controller related resets which causes an endless
hang as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.
Do the full "PCIE Root Complex Initialization Sequence" if the PCIe
host controller is still in reset during probing.
The QCA u-boot sleeps 10ms after the PCIE Application Control bit is
set to ready. It has been shown that 10ms might not be enough time if
PCIe should be used right after setting the bit. During my tests it
took up to 20ms till the link was up. Giving the link up to 100ms
should work for all cases.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19916/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
This patch ensures, that the pinmux register is properly setup for the
boot console UART when early_printk is enabled.
[paul.burton@mips.com:
- s/poinmux/pinmux/
- s/uart/UART/
- Drop extraneous parentheses.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
This patch adds a few additional cpu feature overrides so that they do not
need to be probed at runtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19914/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
This patch disables irq on reboot to fix hang issues that were observed
due to pending interrupts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19913/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
The pinmux on QCA SoCs is controlled by a single register. The
"pinctrl-single" driver can be used but requires the target
to select PINCTRL.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19909/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
This patch adds support for 2 new types of QCA silicon. TP9343 is
essentially the same as the QCA956X but is licensed by TPLink.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19911/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
This patch adds many new registers for various QCA MIPS SoCs. The patch is
an aggragate of many contributions made to OpenWrt.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19910/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
Ocelot now has a u-boot port, allow building FIT images instead of relying
on the legacy detection and builtin DTB.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19632/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
Get rid of extern declarations in .c functions and included
the necessary header file. Also remove unused UART declares.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19477/
Cc: linux-mips@linux-mips.org
|
|
It is not immediately obvious what the expected inputs to these fault
handlers is and how they calculate the number of unset bytes. Having
stared deeply at this in order to fix some corner cases, add some
comments to assist those who follow.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19339/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
|
|
The __clear_user function is defined to return the number of bytes that
could not be cleared. From the underlying memset / bzero implementation
this means setting register a2 to that number on return. Currently if a
page fault is triggered within the MIPSr6 version of setting of initial
unaligned bytes, the value loaded into a2 on return is meaningless.
During the MIPSr6 version of the initial unaligned bytes block, register
a2 contains the number of bytes to be set beyond the initial unaligned
bytes. The t0 register is initally set to the number of unaligned bytes
- STORSIZE, effectively a negative version of the number of unaligned
bytes. This is then incremented before each byte is saved.
The label .Lbyte_fixup\@ is jumped to on page fault. Currently the value
in a2 is incorrectly replaced by 0 - t0 + 1, effectively the number of
unaligned bytes remaining. This leads to the failures being reported by
the following test code:
static int __init test_clear_user(void)
{
int j, k;
pr_info("\n\n\nTesting clear_user\n");
for (j = 0; j < 512; j++) {
if ((k = clear_user(NULL+3, j)) != j) {
pr_err("clear_user (NULL %d) returned %d\n", j, k);
}
}
return 0;
}
late_initcall(test_clear_user);
Which reports:
[ 3.965439] Testing clear_user
[ 3.973169] clear_user (NULL 8) returned 6
[ 3.976782] clear_user (NULL 9) returned 6
[ 3.980390] clear_user (NULL 10) returned 6
[ 3.984052] clear_user (NULL 11) returned 6
[ 3.987524] clear_user (NULL 12) returned 6
Fix this by subtracting t0 from a2 (rather than $0), effectivey giving:
unset_bytes = (#bytes - (#unaligned bytes)) - (-#unaligned bytes remaining + 1) + 1
a2 = a2 - t0 + 1
This fixes the value returned from __clear user when the number of bytes
to set is > LONGSIZE and the address is invalid and unaligned.
Unfortunately, this breaks the fixup handling for unaligned bytes after
the final long, where register a2 still contains the number of bytes
remaining to be set and the t0 register is to 0 - the number of
unaligned bytes remaining.
Because t0 is now is now subtracted from a2 rather than 0, the number of
bytes unset is reported incorrectly:
static int __init test_clear_user(void)
{
char *test;
int j, k;
pr_info("\n\n\nTesting clear_user\n");
test = vmalloc(PAGE_SIZE);
for (j = 256; j < 512; j++) {
if ((k = clear_user(test + PAGE_SIZE - 254, j)) != j - 254) {
pr_err("clear_user (%px %d) returned %d\n",
test + PAGE_SIZE - 254, j, k);
}
}
return 0;
}
late_initcall(test_clear_user);
[ 3.976775] clear_user (c00000000000df02 256) returned 4
[ 3.981957] clear_user (c00000000000df02 257) returned 6
[ 3.986425] clear_user (c00000000000df02 258) returned 8
[ 3.990850] clear_user (c00000000000df02 259) returned 10
[ 3.995332] clear_user (c00000000000df02 260) returned 12
[ 3.999815] clear_user (c00000000000df02 261) returned 14
Fix this by ensuring that a2 is set to 0 during the set of final
unaligned bytes.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 8c56208aff77 ("MIPS: lib: memset: Add MIPS R6 support")
Patchwork: https://patchwork.linux-mips.org/patch/19338/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.0+
|
|
Many architectural features have over time moved from being optional to
either be required or removed by newer architecture releases. This means
that in many cases we can know at compile time whether a feature will be
supported or not purely due to the knowledge we have about the ISA the
kernel build is targeting.
This patch introduces a bunch of utility macros for checking for
supported options, ASEs & combinations of those with ISA revisions. It
then makes use of these in the default definitions of cpu_has_* macros.
The result is that many of the macros become compile-time constant,
allowing more optimisation opportunities for the compiler - particularly
with kernels built for later ISA revisions.
To demonstrate the effect of this patch, the following table shows the
size in bytes of the kernel binary as reported by scripts/bloat-o-meter
for v4.12-rc4 maltasmvp_defconfig kernels with & without this patch. A
variant of maltasmvp_defconfig with CONFIG_CPU_MIPS32_R6 selected is
also shown, to demonstrate that MIPSr6 systems benefit more due to extra
features becoming required by that architecture revision. Builds of
pistachio_defconfig are also shown, as although this is a MIPSr2
platform it doesn't hardcode any features in a machine-specific
cpu-feature-overrides.h, which allows it to gain more from this patch
than the equivalent Malta r2 build.
Config | Before | After | Change
----------------|---------|---------|---------
maltasmvp | 7248316 | 7247714 | -602
maltasmvp + r6 | 6955595 | 6950777 | -4818
pistachio | 8650977 | 8363898 | -287079
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/16360/
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
Make use of the spi-gpio driver to provide SPI support on the Ingenic
JZ4780 SoC using the pins that can be used with the SSI0 device as
GPIOs, until such time as we have support for the Ingenic SPI/SSI
controller.
[paul.burton@mips.com: Rewrite commit message.]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19489/
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
Enable CONFIG_SPI_GPIO in ci20_defconfig, in order to make use of the
spi-gpio driver in a further commit.
[paul.burton@mips.com: Rewrite commit message.]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19488/
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
All Octeons starting with Octeon II have RAPIDIO controller which
can function even with PCI disabled.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Alexandre Bounine <alex.bou9@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19988/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
|
|
Introduce the same option as PPC and ARM already have because
RAPIDIO can function in the absence of PCI.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Alexandre Bounine <alex.bou9@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19987/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
|
|
This is necessary to be able to include <linux/msi.h> when
CONFIG_GENERIC_MSI_IRQ_DOMAIN is enabled. Without this, a build with
CONFIG_GENERIC_MSI_IRQ_DOMAIN fails with:
In file included from include/linux/kvm_host.h:20:0,
from arch/mips/kernel/asm-offsets.c:24:
>> include/linux/msi.h:197:10: fatal error: asm/msi.h: No such file or directory
#include <asm/msi.h>
^~~~~~~~~~~
compilation terminated.
make[2]: *** [arch/mips/kernel/asm-offsets.s] Error 1
make[2]: Target '__build' not remade because of errors.
make[1]: *** [prepare0] Error 2
make[1]: Target 'prepare' not remade because of errors.
make: *** [sub-make] Error 2
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19986/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
Defines CP0_CONFIG3, CP0_CONFIG6, CP0_PAGEGRAIN and use them in
kernel-entry-init.h for Loongson64.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19264/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
|
|
Loongson-3A R3.1 is the bugfix revision of Loongson-3A R3.
All Loongson-3 CPU family:
Code-name Brand-name PRId
Loongson-3A R1 Loongson-3A1000 0x6305
Loongson-3A R2 Loongson-3A2000 0x6308
Loongson-3A R3 Loongson-3A3000 0x6309
Loongson-3A R3.1 Loongson-3A3000 0x630d
Loongson-3B R1 Loongson-3B1000 0x6306
Loongson-3B R2 Loongson-3B1500 0x6307
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19263/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
|
|
Having the zload address at 0x8060.0000 means the size of the
uncompressed kernel cannot be bigger than around 6 MiB, as it is
deflated at address 0x8001.0000.
This limit is too small; a kernel with some built-in drivers and things
like debugfs enabled will already be over 6 MiB in size, and so will
fail to extract properly.
To fix this, we bump the zload address from 0x8060.0000 to 0x8100.0000.
This is fine, as all the boards featuring Ingenic JZ SoCs have at least
32 MiB of RAM, and use u-boot or compatible bootloaders which won't
hardcode the load address but read it from the uImage's header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19787/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
Instead of using dma_alloc_coherent() and memset() directly use
dma_zalloc_coherent().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19962/
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: dev@kresin.me
|
|
Linux expects that if a CPU modifies a memory location, then that
modification will eventually become visible to other CPUs in the system.
Loongson 3 CPUs include a Store Fill Buffer (SFB) which sits between a
core & its L1 data cache, queueing memory accesses & allowing for faster
forwarding of data from pending stores to younger loads from the core.
Unfortunately the SFB prioritizes loads such that a continuous stream of
loads may cause a pending write to be buffered indefinitely. This is
problematic if we end up with 2 CPUs which each perform a store that the
other polls for - one or both CPUs may end up with their stores buffered
in the SFB, never reaching cache due to the continuous reads from the
poll loop. Such a deadlock condition has been observed whilst running
qspinlock code.
This patch changes the definition of cpu_relax() to smp_mb() for
Loongson-3, forcing a flush of the SFB on SMP systems which will cause
any pending writes to make it as far as the L1 caches where they will
become visible to other CPUs. If the kernel is not compiled for SMP
support, this will expand to a barrier() as before.
This workaround matches that currently implemented for ARM when
CONFIG_ARM_ERRATA_754327=y, which was introduced by commit 534be1d5a2da
("ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore").
Although the workaround is only required when the Loongson 3 SFB
functionality is enabled, and we only began explicitly enabling that
functionality in v4.7 with commit 1e820da3c9af ("MIPS: Loongson-3:
Introduce CONFIG_LOONGSON3_ENHANCEMENT"), existing or future firmware
may enable the SFB which means we may need the workaround backported to
earlier kernels too.
[paul.burton@mips.com:
- Reword commit message & comment.
- Limit stable backport to v3.15+ where we support Loongson 3 CPUs.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: 534be1d5a2da ("ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore")
References: 1e820da3c9af ("MIPS: Loongson-3: Introduce CONFIG_LOONGSON3_ENHANCEMENT")
Patchwork: https://patchwork.linux-mips.org/patch/19830/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
Cc: stable@vger.kernel.org # v3.15+
|
|
All conflicts were trivial overlapping changes, so reasonably
easy to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This macro substitution is the shortcut to map cacheable IO memory
with coherent and write-back attributes. Since it is entirely unused
by kernel, lets just remove it.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/19937/
CC: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sinan Kaya <okaya@codeaurora.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Sergey.Semin@t-platforms.ru
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
ath79_ddr_wb_flush_base has the type void __iomem *, so register offsets
need to be a multiple of 4 in order to access the intended register.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 24b0e3e84fbf ("MIPS: ath79: Improve the DDR controller interface")
Patchwork: https://patchwork.linux-mips.org/patch/19912/
Cc: Alban Bedel <albeu@free.fr>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 4.2+
|
|
Define an NT_MIPS_FP_MODE core file note and implement a corresponding
regset holding the state handled by PR_SET_FP_MODE and PR_GET_FP_MODE
prctl(2) requests. This lets debug software correctly interpret the
contents of floating-point general registers both in live debugging and
in core files, and also switch floating-point modes of a live process.
[paul.burton@mips.com:
- Changed NT_MIPS_FP_MODE to 0x801 to match first nibble of
NT_MIPS_DSP, which was also changed to avoid a conflict.]
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19331/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
Define an NT_MIPS_DSP core file note type and implement a corresponding
regset holding the DSP ASE register context, following the layout of the
`mips_dsp_state' structure, except for the DSPControl register stored as
a 64-bit rather than 32-bit quantity in a 64-bit note.
The lack of DSP ASE register saving to core files can be considered a
design flaw with commit e50c0a8fa60d ("Support the MIPS32 / MIPS64 DSP
ASE."), leading to an incomplete state being saved. Consequently no DSP
ASE regset has been created with commit 7aeb753b5353 ("MIPS: Implement
task_user_regset_view."), when regset support was added to the MIPS
port.
Additionally there is no way for ptrace(2) to correctly access the DSP
accumulator registers in n32 processes with the existing interfaces.
This is due to 32-bit truncation of data passed with PTRACE_PEEKUSR and
PTRACE_POKEUSR requests, which cannot be avoided owing to how the data
types for ptrace(3) have been defined. This new NT_MIPS_DSP regset
fills the missing interface gap.
[paul.burton@mips.com:
- Change NT_MIPS_DSP to 0x800 to avoid conflict with NT_VMCOREDD
introduced by commit 2724273e8fd0 ("vmcore: add API to collect
hardware dump in second kernel").
- Drop stable tag. Whilst I agree the lack of this functionality can
be considered a flaw in earlier DSP ASE support, it's still new
functionality which doesn't meet up to the requirements set out in
Documentation/process/stable-kernel-rules.rst.]
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
Patchwork: https://patchwork.linux-mips.org/patch/19330/
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
Use the `unsigned long' rather than `__u32' type for DSP accumulator
registers, like with the regular MIPS multiply/divide accumulator and
general-purpose registers, as all are 64-bit in 64-bit implementations
and using a 32-bit data type leads to contents truncation on context
saving.
Update `arch_ptrace' and `compat_arch_ptrace' accordingly, removing
casts that are similarly not used with multiply/divide accumulator or
general-purpose register accesses.
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: e50c0a8fa60d ("Support the MIPS32 / MIPS64 DSP ASE.")
Patchwork: https://patchwork.linux-mips.org/patch/19329/
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 2.6.15+
|
|
This way we will be able to compile the jz4740_nand driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This way we will be able to compile the ndfmc driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The PCI_OHCI_INT_REG case in pci_ohci_read_reg() contains the following
if statement:
if ((lo & 0x00000f00) == CS5536_USB_INTR)
CS5536_USB_INTR expands to the constant 11, which gives us the following
condition which can never evaluate true:
if ((lo & 0xf00) == 11)
At least when using GCC 8.1.0 this falls foul of the tautoligcal-compare
warning, and since the code is built with the -Werror flag the build
fails.
Fix this by shifting lo right by 8 bits in order to match the
corresponding PCI_OHCI_INT_REG case in pci_ohci_write_reg().
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19861/
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
prom_putchar() is used centrally in early printk infrastructure therefore
at least MIPS should agree on the function return type.
[paul.burton@mips.com:
- Include linux/types.h in asm/setup.h to gain the bool typedef before
we start include asm/setup.h elsewhere.
- Include asm/setup.h in all files that use or define prom_putchar().
- Also standardise on signed rather than unsigned char argument.]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19842/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The MIPS implementation of pci_resource_to_user() introduced in v3.12 by
commit 4c2924b725fb ("MIPS: PCI: Use pci_resource_to_user to map pci
memory space properly") incorrectly sets *end to the address of the
byte after the resource, rather than the last byte of the resource.
This results in userland seeing resources as a byte larger than they
actually are, for example a 32 byte BAR will be reported by a tool such
as lspci as being 33 bytes in size:
Region 2: I/O ports at 1000 [disabled] [size=33]
Correct this by subtracting one from the calculated end address,
reporting the correct address to userland.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Rui Wang <rui.wang@windriver.com>
Fixes: 4c2924b725fb ("MIPS: PCI: Use pci_resource_to_user to map pci memory space properly")
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v3.12+
Patchwork: https://patchwork.linux-mips.org/patch/19829/
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch reduces down the conditionals in MIPS atomic code that deal
with a silicon bug in early R10000 cpus that required a workaround of
a branch-likely instruction following a store-conditional in order to
to guarantee the whole ll/sc sequence is atomic. As the only real
difference is a branch-likely instruction (beqzl) over a standard
branch (beqz), the conditional is reduced down to a single preprocessor
check at the top to pick the required instruction.
This requires writing the uses in assembler, thus we discard the
non-R10000 case that uses a mixture of a C do...while loop with
embedded assembler that was added back in commit 7837314d141c ("MIPS:
Get rid of branches to .subsections."). A note found in the git log
for commit 5999eca25c1f ("[MIPS] Improve branch prediction in ll/sc
atomic operations.") is also addressed.
The macro definition for the branch instruction and the code comment
derives from a patch sent in earlier by Paul Burton for various cmpxchg
cleanups.
[paul.burton@mips.com:
- Minor whitespace fix for checkpatch.]
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/17736/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: "Maciej W. Rozycki" <macro@mips.com>
Cc: linux-mips@linux-mips.org
|
|
This patch fixes an old bug in MIPS ll/sc atomics, in the
`atomic_sub_if_positive' and `atomic64_sub_if_positive' functions, for
the R10000_LLSC_WAR case where the result of the subu/dsubu instruction
would potentially not be made available to the sc/scd instruction due
to being in the delay-slot of the branch-likely (beqzl) instruction.
This also removes the need for the `noreorder' directive, allowing GAS
to use delay slot scheduling as needed.
The same fix is also applied to the standard branch (beqz) case in
preparation for a follow-up patch that will cleanup/merge the
R10000_LLSC_WAR and non-R10K sections together.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Tested-by: Joshua Kinard <kumba@gentoo.org>
Patchwork: https://patchwork.linux-mips.org/patch/17735/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: "Maciej W. Rozycki" <macro@mips.com>
Cc: linux-mips@linux-mips.org
|
|
Commit 205e1b7f51e4 ("dma-mapping: warn when there is no
coherent_dma_mask") introduced a warning, if a device is missing a
coherent_dma_mask. ESP and sonic are using dma mapping functions, so
they need dma masks.
[paul.burton@mips.com:
- Wrap commit message.]
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19828/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
Adaptive ioremap_wc() method is now available as of commit 9748e33e26c6
("mips: mm: Create UCA-based ioremap_wc() method"). We can use it to
obtain UnCached Accelerated (UCA) mappings safely on all MIPS systems,
and so we don't need the MIPS-specific ioremap_uncached_accelerated()
any longer. This macro hard-coded the UCA Cache Coherency Attribute
(CCA) in a manner that isn't safe for kernels that may run on different
CPUs, and it is also entirely unused so we can trivially remove it.
[paul.burton@mips.com:
- Reword the commit message a little.
- Remove CC stable.]
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19790/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: okaya@codeaurora.org
Cc: chenhc@lemote.com
Cc: Sergey.Semin@t-platforms.ru
Cc: linux-kernel@vger.kernel.org
|
|
Modern MIPS cores (like P5600/6600, M5150/6520, end so on) which
got L2-cache on chip also can enable a special type Cache-Coherency
attribute (CCA) named UnCached Accelerated attribute (UCA). In this
way uncached accelerated accesses are treated the same way as
non-accelerated uncached accesses, but uncached stores are gathered
together for more efficient bus utilization. So to speak this CCA
enables uncached transactions to better utilize bus bandwidth via
burst transactions.
This is exactly why ioremap_wc() method has been introduced in Linux.
Alas MIPS-platform code hasn't implemented it so far, instead default
one has been used which was an alias to ioremap_nocache. In order to
fix this we added MIPS-specific ioremap_wc() macro substituted by
generic __ioremap_mode() method call with writecombine CPU-info
field passed. It shall create real ioremap_wc() method if CPU-cache
supports UCA feature and fall-back to _CACHE_UNCACHED attribute
if one doesn't. Additionally platform-specific io.h shall declare
ARCH_HAS_IOREMAP_WC macro as indication of architectural definition
of ioremap_wc() (similar to x86/powerpc).
[paul.burton@mips.com:
- Remove CC stable, this is new functionality.]
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19789/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: okaya@codeaurora.org
Cc: chenhc@lemote.com
Cc: Sergey.Semin@t-platforms.ru
Cc: linux-kernel@vger.kernel.org
|
|
Many shash algorithms set .cra_flags = CRYPTO_ALG_TYPE_SHASH. But this
is redundant with the C structure type ('struct shash_alg'), and
crypto_register_shash() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the shash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
We currently attempt to check whether a physical address range provided
to __ioremap() may be in use by the page allocator by examining the
value of PageReserved for each page in the region - lowmem pages not
marked reserved are presumed to be in use by the page allocator, and
requests to ioremap them fail.
The way we check this has been broken since commit 92923ca3aace ("mm:
meminit: only set page reserved in the memblock region"), because
memblock will typically not have any knowledge of non-RAM pages and
therefore those pages will not have the PageReserved flag set. Thus when
we attempt to ioremap a region outside of RAM we incorrectly fail
believing that the region is RAM that may be in use.
In most cases ioremap() on MIPS will take a fast-path to use the
unmapped kseg1 or xkphys virtual address spaces and never hit this path,
so the only way to hit it is for a MIPS32 system to attempt to ioremap()
an address range in lowmem with flags other than _CACHE_UNCACHED.
Perhaps the most straightforward way to do this is using
ioremap_uncached_accelerated(), which is how the problem was discovered.
Fix this by making use of walk_system_ram_range() to test the address
range provided to __ioremap() against only RAM pages, rather than all
lowmem pages. This means that if we have a lowmem I/O region, which is
very common for MIPS systems, we're free to ioremap() address ranges
within it. A nice bonus is that the test is no longer limited to lowmem.
The approach here matches the way x86 performed the same test after
commit c81c8a1eeede ("x86, ioremap: Speed up check for RAM pages") until
x86 moved towards a slightly more complicated check using walk_mem_res()
for unrelated reasons with commit 0e4c12b45aa8 ("x86/mm, resource: Use
PAGE_KERNEL protection for ioremap of memory pages").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Fixes: 92923ca3aace ("mm: meminit: only set page reserved in the memblock region")
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.2+
Patchwork: https://patchwork.linux-mips.org/patch/19786/
|
|
This patch introduces SO_TXTIME. User space enables this option in
order to pass a desired future transmit time in a CMSG when calling
sendmsg(2). The argument to this socket option is a 8-bytes long struct
provided by the uapi header net_tstamp.h defined as:
struct sock_txtime {
clockid_t clockid;
u32 flags;
};
Note that new fields were added to struct sock by filling a 2-bytes
hole found in the struct. For that reason, neither the struct size or
number of cachelines were altered.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collapse and simplify switch statements in functions.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19713/
Cc: linux-mips@linux-mips.org
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
|
|
Create new CVMX_CIU_ADDR macro to improve readability.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19712/
Cc: linux-mips@linux-mips.org
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
|
