summaryrefslogtreecommitdiff
path: root/arch/mips/alchemy/common/power.c
AgeCommit message (Collapse)Author
2009-01-11MIPS: Alchemy: new userspace suspend interface for development boards.Manuel Lauss
Replace the current sysctl-based suspend interface with a new sysfs- based one which also uses the Linux-2.6 suspend model. To configure wakeup sources, a subtree for the demoboards is created under /sys/power/db1x: sys/ `-- power `-- db1x |-- gpio0 |-- gpio1 |-- gpio2 |-- gpio3 |-- gpio4 |-- gpio5 |-- gpio6 |-- gpio7 |-- timer |-- timer_timeout |-- wakemsk `-- wakesrc The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2 bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1' enables a wakesource, 0 disables it. The 'timer_timeout' node holds the timeout in seconds after which the TOYMATCH2 event should wake the system. The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex), the 'wakemsk' node can be used to get/set the wakeup mask directly. For example, to have the timer wake the system after 10 seconds of sleep, the following must be done in userspace: echo 10 > /sys/power/db1x/timer_timeout echo 1 > /sys/power/db1x/timer echo mem > /sys/power/sleep This patch also removes the homebrew CPU frequency switching code. I don't understand how it could have ever worked reliably; it does not communicate the clock changes to peripheral devices other than uarts. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> create mode 100644 arch/mips/alchemy/devboards/pm.c
2009-01-11MIPS: Alchemy: dbdma suspend/resume support.Manuel Lauss
Implement suspend/resume for DBDMA controller and its channels. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-11MIPS: Alchemy: Fix up PM code on Au1550/Au1200Manuel Lauss
Au1550/Au1200 have a different memory controller which requires additi- onal code to properly put memory to sleep (code taken from AMD/RMI's Linux-2.6.11 source package). Also fix up the remaining pm-related paths to compile on Au1200/Au1550 platforms. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-11MIPS: Alchemy: RTC counter clocksource / clockevent support.Manuel Lauss
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent device. As a nice side effect, this also enables use of the 'wait' instruction for runtime idle power savings. If the counters aren't enabled/working properly, fall back on the cp0 counter clock code. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-11MIPS: Alchemy: update core interrupt code.Manuel Lauss
This patch attempts to modernize core Alchemy interrupt handling code. - add irq_chips for irq controllers instead of irq type, - add a set_type() hook to change irq trigger type during runtime, - add a set_wake() hook to control GPIO0..7 based wakeup, - use linux' IRQF_TRIGGER_ constants instead of homebrew ones, - enable GENERIC_HARDIRQS_NO__DO_IRQ. - simplify plat_irq_dispatch - merge au1xxx_irqmap into irq.c file, the only place where its contents are referenced. - board_init_irq() is now mandatory for every board; use it to register the remaining (gpio-based) interrupt sources; update all boards accordingly. Run-tested on Db1200 and other Au1200 based platforms. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
2008-10-11MIPS: Alchemy: rename directoryRalf Baechle
It's more than the au1000 these days. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>