| Age | Commit message (Collapse) | Author |
|---|
|
Interacting with the USB_PHY_TEST MMR through debugfs was causing wide-spread
chaos in the realm (kernel panic). Expunge all references to this demonic
register.
Signed-off-by: Andre Wolokita <Andre.Wolokita@analog.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Remove gpio driver for new gpio controller on BF54x and BF60x.
Build the bfin_gpio driver only when other BF5xx processors are selected.
Replace the prefix of some gpio and peripheral functions with adi.
add portmux platform data in machine portmux.h
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
Drivers common to both bf5xx and bf60x chip families may use this anomaly id.
So add it to bf5xx header files also.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
Turn SEC related macro CONFIG_BF60x into SEC_GCTL.
Move machine specific GPIO_PINT macros to machine gpio header.
Split SEC init_arch_irq() and vec_to_irq() from old SIC.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
Change ADI BSD license to standart 3 clause BSD license for some blackfin arch
code requested by ADI Legal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
Have the logic that uses peripheral interrupt blocks key off of pint
defines rather than CPU names so that things are generalized across
families.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The hardware block uses the name "request" rather than "irq", so update
the struct accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The bf52x/bf54x have the incorrect addresses for USB_EP_NI7_RXINTERVAL
and USB_EP_NI7_TXCOUNT, so adjust those.
Further, the bf54x header puts the USB defines in the wrong place, so
shuffle them back to the right grouping.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the serial code has been unified in bfin_serial.h, and the
Blackfin UART driver pushed its resources to the boards files, we
don't need these headers anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
These files had a lot of whitespace damage, mostly due to copying and
pasting original files that had damage.
The BF561 header also had a lot of unused CONFIG_DEF_xxx defines, so
punt them all.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Start a new common IRQ header and move all of the CEC pieces there. This
lets the individual part headers worry just about its SIC defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Even though the anomaly sheet says that the the bootrom is fixed, tests
have shown that the fix itself does not handle all cases. So until we
get a ROM update, assume the reset code is still broken and we need to
handle things ourselves.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
No code uses these, and the short define names are polluting the global
namespace where they collide with things like common irq files. So just
punt the damned things. If in the future we need HDMA support, we can
make a standalone header for these things.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The BF54x lacks dedicated DMA channels for the UART peripherals and need
to be muxed between others. So add a kconfig option so people can select
which channels the UARTs will use so they can pick between SPORTs and the
less commonly used EPPI/PIXC peripherals.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
These were only included because of the irq handling of the PLL funcs,
and those PLL funcs have been moved out into their own header now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The main asm/blackfin.h header will pull in mach/blackfin.h to get
all the fun Blackfin defines. So having any of the sub-mach headers
trying to include asm/blackfin.h makes no sense -- punt it.
The mach/blackfin.h header takes care of including the part-specific
def headers which in turn will include any other needed def file.
Similarly, it takes care of pulling in the part-specific cdef header.
So move this logic out of the blackfin.h when necessary.
Further, make sure the cdef headers do not waste time including the
def headers again.
Since all parts need the common def/cdef headers, move this logic
out of the part-specific headers and into the mach/blackfin.h file.
Finally, we need to split the BF539 def header since the BF538 does
not have MXVR and we don't want to expose those MMRs.
So now all parts should have the same behavior:
mach/blackfin.h
asm/def_LPBlackfin.h
part-specific def.h
if ! asm
asm/cdef_LPBlackfin.h
part-specific cdef.h
And the sub def/cdef headers only tail into what they need.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Use the same naming convention for DMA traffic MMRs (most were legacy
anyways) so we can avoid useless ifdef trees.
Same goes for MDMA names -- this actually allows us to undo a bunch of
ifdef redirects that existed for this purpose alone.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Each Blackfin port has been duplicating UART structures and defines when
there really is no need for it. So start a new bfin_serial.h header to
unify all these pieces and give ourselves a fresh start.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the common header defines everything and the SPI drivers are
using it, we can drop these duplicated global namespace polluters.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch. This renames local_*_hw() to hard_local_*() using the
following perl command:
perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`
and then fixing up asm/irqflags.h manually.
Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Split the PLL control code from the Blackfin machine-specific cdef headers so
that the irqflags functions can be renamed without incurring a header loop.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
The common bfin_sport.h header now has unified definitions of these, so
stop polluting the global namespace.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Avoid duplication and ugly global namespace pollution.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Avoid duplication and ugly global namespace pollution.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The standard short name for control is CTL and not CTRL. Use TWI0_xxx
even on parts that only have one TWI bus to keep things simple. Drop
all the cdef helpers since the bus driver takes care of everything.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Random tabs instead of spaces, mixes of the two, and unicode spaces
instead of ascii spaces.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This is parallel to the existing P_DEFAULT_BOOT_SPI_CS, but in terms of
the GPIO value so it can be used with the normal gpio API.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the NFC driver has its own defines, scrub the ones from the
global namespace to avoid ugly collisions with common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that there's a common header with everything unified, drop the defines
from the global namespace. Pollution sucks.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This makes room for off-chip IRQ controllers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
While we're moving the BF54x code, have the BF54xM variants select the
normal BF54x values so that the rest of the Kconfig tree doesn't need to
check the BF54xM variant everytime it wants to check the BF54x.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Every Blackfin variant has the same DMA bit masks, so avoid duplicating
them over and over in each mach header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
There's no point in having mask defines when the entire MMR value is a
count or address. i.e. applying a mask of -1 is pointless.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
There are no MXVR device drivers, and if someday there is, we can put
these in a dedicated header rather than polluting the global namespace.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
People should not be accessing OTP MMRs directly. They should instead go
through the Blackfin ROM helper functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The watchdog code doesn't need these, and the other parts had these
punted, so keep the global namespace clean.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The RTC driver code doesn't need these, and the other parts had these
punted, so keep the global namespace clean.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
