summaryrefslogtreecommitdiff
path: root/arch/blackfin/mach-bf537/boards
AgeCommit message (Collapse)Author
2013-05-30blackfin: Remove references to the bf5x_tdm driverLars-Peter Clausen
The bf5x_tdm driver has been removed. Remove all references to it from board code. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-05-30ASoC: blackfin: Switch bf5xx-ad1836 from bf5xx-tdm to bf5xx-i2sLars-Peter Clausen
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is going to be removed soon, so switch the driver over to bf5xx-i2s. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-05-07Platform Nand: Set the GPIO for NAND read as inputAaron Wu
This patch is from Frank.Shew,fshew@geometrics.com to fix the following problem:having extremely slow responses with the NAND due to timeouts on the ready status signal, which eventually caused the watchdog to time out. Signed-off-by: Aaron Wu <Aaron.Wu@analog.com> Signed-off-by: Steven Miao <realmz6@gmail.com>
2012-10-09Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin Pull blackfin update from Bob Liu. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin: Blackfin: smp: add smp_mb() to keep coherency Blackfin: drop irq enable in init_arch_irq() Blackfin: fix wrong place disabled irq Blackfin: update defconfig for bf609-ezkit Blackfin: add bf548 v0.4 revision Blackfin: bf60x: Add bf608 and bf609 specific perpheral MMRs Blackfin: cpufreq: fix dpm_state_table Blackfin: bfin_gpio: proc: fix return value Blackfin: CM-BF537E: Update SPORT support in board file. Blackfin: bf537: fix lq035 platform device name Blackfin: bf533-ezkit: enable flash drivers by default
2012-10-08Blackfin: CM-BF537E: Update SPORT support in board file.Harald Krapfenbauer
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.at> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-10-08Blackfin: bf537: fix lq035 platform device nameScott Jiang
Lq035 fb driver uses KBUILD_MODNAME which is bf537_lq035 instead of bf537-lq035. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-08-17blackfin: add platform device for ad1836 machine driverScott Jiang
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-16arch: Use eth_random_addrJoe Perches
Convert the existing uses of random_ether_addr to the new eth_random_addr. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-21blackfin: twi: Move TWI peripheral pin request array to platform dataSonic Zhang
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-05-21blackfin: bf537-stamp: update board file for platform bfin_sport deviceAaron Wu
Blackfin sport driver has been rewrited update board file according. Signed-off-by: Aaron Wu <Aaron.Wu@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-03-21Blackfin: pnav: delete duplicate linux/export.h includeDanny Kukawka
arch/blackfin/mach-bf537/boards/pnav10.c includes 'linux/export.h' twice. No need to include the file a second time in a #ifdef block if already included at top. Remove the duplicate. Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-03-21arch/blackfin: don't generate random mac in bfin_get_ether_addr()Danny Kukawka
Changed bfin_get_ether_addr() to return a state and to set no random mac address if the board don't provide one. Let the caller of bfin_get_ether_addr() set a random mac address if the return value is not 0. v2: don't set random mac in bfin_get_ether_addr() Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-03-21bfin: add bfin_ad73311_machine platform deviceBob Liu
we can pass sport enable pin through platform data if customer board has reset pin, add it in ad73311_gpio array and modify id to 2 Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-03-21blackfin: bf537: stamp: update board file for 193xBob Liu
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-01-09blackfin: bf537: add capture supportBob Liu
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-01-09blackfin: bf537: change num_chipselect for spi-sportScott Jiang
spi sport driver can support any gpio as its cs pin. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-01-09blackfin: config: update macro SPI_BFIN in board fileSonic Zhang
Macro name for spi controller driver has been modified, so update default board file accordingly. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2011-11-14blackfin: Fixup export.h includesLars-Peter Clausen
Commit 8dc7a9c84 ("blackfin: Add export.h to files using EXPORT_SYMBOL/THIS_MODULE") inserted some of the include statements into sections protected by an unrelated #if CONFIG_... statement. This can cause, depending on the configuration used, warnings like this one: arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: data definition has no type or storage class arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: parameter names (without types) in function declaration This patch fixes it by moving the includes out of the #if protected sections. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2011-11-14Blackfin: add serial TX IRQ in individual platform resourceSonic Zhang
The serial TX IRQ is not simply (RX IRQ + 1) on some Blackfin chips, so move the values to the platform resources. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2011-10-31blackfin: Add export.h to files using EXPORT_SYMBOL/THIS_MODULEPaul Gortmaker
These particular files were just assuming that module.h was somehow in the include paths. Give them the more minimalist header file explicitly. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-26Blackfin: irq: remove IRQF_DISABLEDYong Zhang
This flag is a NOOP and can be removed now. Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Acked-by: Bob Liu <lliubbo@kernel.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-25Blackfin: boards: clean up i2c_board_infoMichael Hennerich
Remove i2c_board_info for driver that doesn't exist anymore. Delete irq_flags for drivers that don't use them anymore. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-25Blackfin: bf537-stamp: register ASoC EVAL-ADAU1373 board driverLars-Peter Clausen
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-25Blackfin: bf537-stamp: Register adav801 codec and ASoC machine driverLars-Peter Clausen
There is already an entry in the spi device table for the codec, but the modalias was wrong. Also the config symbol name for the codec is wrong, so this is fixed as well. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-25Blackfin: bf537-stamp: register adau1701 codec and asoc machine driverLars-Peter Clausen
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-25Blackfin: bf537-stamp: fix ad73311 codec config macroScott Jiang
SND_BF5XX_SOC is for machine drivers while SND_SOC is for codec drivers. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-25Blackfin: bf537-stamp: fix ad1836 nameScott Jiang
The ASoC codec name is "ad1836" and not "ad183x" as the change to rename things ultimately did not get merged. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-07-23Blackfin: boards: fix pcm device nameScott Jiang
The pcm driver name has been changed, but the device name has not. Signed-off-by: Scott Jiang <scott.jiang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-07-23Blackfin: boards: clean up redundant/dead spi resourcesMike Frysinger
The default for the Blackfin SPI driver is 8 bits and dma disabled, so many of the bfin5xx_spi_chip resources are redundant. So punt those parts. Further, drivers should themselves be declaring 16 bit transfers, so for those that do, and for the ones which no longer do 16 bit transfers, drop the bfin5xx_spi_chip resources. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-07-23Blackfin: net2272: move pin setup to boards filesMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-27Merge git://git.infradead.org/mtd-2.6Linus Torvalds
* git://git.infradead.org/mtd-2.6: (97 commits) mtd: kill CONFIG_MTD_PARTITIONS mtd: remove add_mtd_partitions, add_mtd_device and friends mtd: convert remaining users to mtd_device_register() mtd: samsung onenand: convert to mtd_device_register() mtd: omap2 onenand: convert to mtd_device_register() mtd: txx9ndfmc: convert to mtd_device_register() mtd: tmio_nand: convert to mtd_device_register() mtd: socrates_nand: convert to mtd_device_register() mtd: sharpsl: convert to mtd_device_register() mtd: s3c2410 nand: convert to mtd_device_register() mtd: ppchameleonevb: convert to mtd_device_register() mtd: orion_nand: convert to mtd_device_register() mtd: omap2: convert to mtd_device_register() mtd: nomadik_nand: convert to mtd_device_register() mtd: ndfc: convert to mtd_device_register() mtd: mxc_nand: convert to mtd_device_register() mtd: mpc5121_nfc: convert to mtd_device_register() mtd: jz4740_nand: convert to mtd_device_register() mtd: h1910: convert to mtd_device_register() mtd: fsmc_nand: convert to mtd_device_register() ... Fixed up trivial conflicts in - drivers/mtd/maps/integrator-flash.c: removed in ARM tree - drivers/mtd/maps/physmap.c: addition of afs partition probe type clashing with removal of CONFIG_MTD_PARTITIONS
2011-05-25Blackfin: boards: update ASoC resources after machine driver overhaulScott Jiang
Now that the Blackfin machine drivers have been updated to the multicomponent support, update the resources to match. The pin settings are now a board issue and removed from the driver. Signed-off-by: Scott Jiang <scott.jiang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25mtd: bfin: convert to mtd_device_register()Jamie Iles
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS preprocessor conditionals as partitioning is always available. Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-18Blackfin: use proper wrapper functions for modifying irq statusThomas Gleixner
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-03-18Blackfin: dnp5370: drop MMC card detect supportAndreas Schallenberg
The board doesn't actually have a pin hooked up to do card detection, so punt the code for it. Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-01-10Blackfin: boards: add missing "static" to peripheral listsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-01-10Blackfin: DNP5370: new board portAndreas Schallenberg
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-01-10Blackfin: sport_uart resources: remove unused secondary RX/TX pinsSonic Zhang
The SPORT/UART driver doesn't use the secondary channel pins, so don't try and request them thus keeping other drivers from using them. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-25netdev: bfin_mac: push settings to platform resourcesSonic Zhang
Move all the pin settings out of the Kconfig and into the platform resources (MII vs RMII). This clean up also lets us push out the phy settings so that board porters may control the layout. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-24Merge branch 'for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits) Update broken web addresses in arch directory. Update broken web addresses in the kernel. Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget Revert "Fix typo: configuation => configuration" partially ida: document IDA_BITMAP_LONGS calculation ext2: fix a typo on comment in ext2/inode.c drivers/scsi: Remove unnecessary casts of private_data drivers/s390: Remove unnecessary casts of private_data net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data drivers/infiniband: Remove unnecessary casts of private_data drivers/gpu/drm: Remove unnecessary casts of private_data kernel/pm_qos_params.c: Remove unnecessary casts of private_data fs/ecryptfs: Remove unnecessary casts of private_data fs/seq_file.c: Remove unnecessary casts of private_data arm: uengine.c: remove C99 comments arm: scoop.c: remove C99 comments Fix typo configue => configure in comments Fix typo: configuation => configuration Fix typo interrest[ing|ed] => interest[ing|ed] Fix various typos of valid in comments ... Fix up trivial conflicts in: drivers/char/ipmi/ipmi_si_intf.c drivers/usb/gadget/rndis.c net/irda/irnet/irnet_ppp.c
2010-10-22Blackfin: boards: add example i2c resources for ad525x devicessteven miao
Signed-off-by: steven miao <realmz6@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: tweak i2c address for ad5280 add-on tftlcd boardSonic Zhang
The predefined i2c address 0x2c doesn't match the configuration of the ad5280 PINs AD0 and AD1 on the tftlcd add-on board. Both AD0 and AD1 are of voltage 3.3V, which means the i2c address should be 0x2F. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: re-use regulator framework with ad5398 partsSonic Zhang
We don't need our own header and structure to hook up the ad5398 part, so drop the custom resources for it. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: re-use the fixed regulator voltage driverSonic Zhang
Rather than write our own ADP switch driver, use the existing fixed regulator driver and rewrite the platform resources accordingly. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: add example IIO resourcesMichael Hennerich
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: use correct spi mode with ad2s90 partsBarry Song
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: add example adau1373 i2c resourcesCliff Cai
Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: add example adav801/3 resourcesYi Li
Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22Blackfin: bf537-stamp: add example ad1937 i2c resourcesBarry Song
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-15 02:08:34 +0000