| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Regression fix for omap interconnect code for deferred probe.
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
* tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM fixes from Russell King:
"A number of ARM fixes:
- prevent oopses caused by dma_get_sgtable() and declared DMA
coherent memory
- fix boot failure on nommu caused by ID_PFR1 access
- a number of kprobes fixes from Jon Medhurst and Masami Hiramatsu"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8665/1: nommu: access ID_PFR1 only if CPUID scheme
ARM: dma-mapping: disallow dma_get_sgtable() for non-kernel managed memory
arm: kprobes: Align stack to 8-bytes in test code
arm: kprobes: Fix the return address of multiple kretprobes
arm: kprobes: Skip single-stepping in recursing path if possible
arm: kprobes: Allow to handle reentered kprobe on single-stepping
|
|
mvebu fixes for 4.11 (part 1)
Fix build of the board code for orion5x when some parts are configured
as module.
* tag 'mvebu-fixes-4.11-1' of git://git.infradead.org/linux-mvebu:
ARM: orion5x: only call into phylib when available
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.11, bis
Two fixes for the recent A33 cpufreq support, and one to fix a missing
register in the A64 USB PHY node.
* tag 'sunxi-fixes-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
From: Christoffer Dall <cdall@linaro.org>
KVM/ARM Fixes for v4.11-rc6
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
|
|
Starting from commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind") pm_runtime core now changes
device runtime_status back to after RPM_SUSPENDED after a probe defer.
Certain OMAP devices make use of "ti,no-idle-on-init" flag which causes
omap_device_enable to be called during the BUS_NOTIFY_ADD_DEVICE event
during probe, along with pm_runtime_set_active.
This call to pm_runtime_set_active typically will prevent a call to
pm_runtime_get in a driver probe function from re-enabling the
omap_device. However, in the case of a probe defer that happens before
the driver probe function is able to run, such as a missing pinctrl
states defer, pm_runtime_reinit will set the device as RPM_SUSPENDED and
then once driver probe is actually able to run, pm_runtime_get will see
the device as suspended and call through to the omap_device layer,
attempting to enable the already enabled omap_device and causing errors
like this:
omap-gpmc 50000000.gpmc: omap_device: omap_device_enable() called from
invalid state 1
omap-gpmc 50000000.gpmc: use pm_runtime_put_sync_suspend() in driver?
We can avoid this error by making sure the pm_runtime status of a device
matches the omap_device state before a probe attempt. By extending the
omap_device bus notifier to act on the BUS_NOTIFY_BIND_DRIVER event we
can check if a device is enabled in omap_device but with a pm_runtime
status of RPM_SUSPENDED and once again mark the device as RPM_ACTIVE to
avoid a second incorrect call to omap_device_enable.
Fixes: 5de85b9d57ab ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We currently have some code to clear the list registers on GICv3, but we
never call this code, because the caller got nuked when removing the old
vgic. We also used to have a similar GICv2 part, but that got lost in
the process too.
Let's reintroduce the logic for GICv2 and call the logic when we
initialize the use of hypervisors on the CPU, for example when first
loading KVM or when exiting a low power state.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In kvm_free_stage2_pgd() we don't hold the kvm->mmu_lock while calling
unmap_stage2_range() on the entire memory range for the guest. This could
cause problems with other callers (e.g, munmap on a memslot) trying to
unmap a range. And since we have to unmap the entire Guest memory range
holding a spinlock, make sure we yield the lock if necessary, after we
unmap each PUD range.
Fixes: commit d5d8184d35c9 ("KVM: ARM: Memory virtualization setup")
Cc: stable@vger.kernel.org # v3.10+
Cc: Paolo Bonzini <pbonzin@redhat.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[ Avoid vCPU starvation and lockup detector warnings ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"At this time, most of changes are for ASoC, while we got one fix for
yet another race of ALSA sequencer core and a usual HD-audio quirk.
The ASoC changes are mostly small and device-specific fixes. A
slightly large volume is seen in sun8i-codec, which is a new code in
4.11, and we'd like to fix user-visible stuff before the official 4.1
release"
* tag 'sound-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ALSA: hda - fix a problem for lineout on a Dell AIO machine
ASoC: simple-card: fix simple_dai clk lookup
ASoC: STI: Fix reader substream pointer set
ALSA: seq: Fix race during FIFO resize
ARM: dts: sun8i: Update audio-routing with renamed widgets
ASoC: sun8i-codec: Convert to use SND_SOC_DAPM_AIF_IN
ASoC: sun8i-codec: Fix space on audio-routing widget
ASoC: sun8i-codec: Update mixer to use SOC_DAPM_DOUBLE
ASoC: sun8i-codec: Remove analog "HP" widget
ASoC: rt5665: fix wrong shift rt5665_if2_1_adc_in_enum
ASoC: rt5665: fix define of RT5665_HP_DRIVER_5X
ASoC: rcar: dma: remove unnecessary "volatile"
ASoC: rcar: clear DE bit only in PDMACHCR when it stops
ASoC: rsnd: fix sound route path when using SRC6/SRC9
ASoC: don't dereference NULL pcm_{new,free}
ASoC: rt5665: CLKDET is also a power of ASRC
ASoC: rt5665: Vref3 is necessary for Mono Amp
ASoC: rt5665: increase LDO level
ASoC: rt5665: fix getting wrong work handler container
ASoC: atmel-classd: fix audio clock rate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.11
A relatively large pile of fixes for mainline, the first since the merge
window. The biggest block of changes here by volume is the sun8i-codec
set, the driver was newly added in the merge window but it was realized
that renaming some of the user visible controls was required so these
are being pushed for v4.11 to avoid the original code appearing in a
release. Otherwise it's all fairly standard bugfix stuff.
|
|
Board code cannot call mdiobus_register_board_info() when phylib
or mdio_device is a loadable module:
arch/arm/plat-orion/common.o: In function `orion_ge00_switch_init':
:(.init.text+0x474): undefined reference to `mdiobus_register_board_info'
I had a number of ideas for how this could be solved, but after the MDIO
code got split out from PHYLIB it has gotten too hard, so I'm basically
giving up, and only call the mdiobus_register_board_info() function
if the MDIO layer is built-in to avoid the link error. This is similar
to how we handle PHY registration on other ARM platforms.
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea0134069 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Greg upon trying to boot no-MMU Kernel on ARM926EJ reported boot
failure. He root caused it to ID_PFR1 access introduced by the
commit mentioned in the fixes tag below.
All CP15 processors need not have processor feature registers, only
for architectures defined by CPUID scheme would have it. Hence check
for it before accessing processor feature register, ID_PFR1.
Fixes: f8300a0b5de0 ("ARM: 8647/2: nommu: dynamic exception base address setting")
Reported-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Tested-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
dma_get_sgtable() tries to create a scatterlist table containing valid
struct page pointers for the coherent memory allocation passed in to it.
However, memory can be declared via dma_declare_coherent_memory(), or
via other reservation schemes which means that coherent memory is not
guaranteed to be backed by struct pages. In such cases, the resulting
scatterlist table contains pointers to invalid pages, which causes
kernel oops later.
This patch adds detection of such memory, and refuses to create a
scatterlist table for such memory.
Reported-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Commit 3251885285e1 ("ARM: OMAP4+: Reset CPU1 properly for kexec") started
unconditionally resetting CPU1 because of a kexec boot issue I was seeing
earlier on omap4 when doing kexec boot between two different kernel
versions.
This caused issues on some systems. We should only reset CPU1 as a last
resort option, and try to avoid it where possible. Doing an unconditional
CPU1 reset causes issues for example when booting a bootloader configured
secure OS running on CPU1 as reported by Andrew F. Davis <afd@ti.com>.
We can't completely remove the reset of CPU1 as it would break kexec
booting from older kernels. But we can limit the CPU1 reset to cases
where CPU1 is wrongly parked within the memory area used by the booting
kernel. Then later on we can add support for parking CPU1 for kexec out
of the SDRAM back to bootrom.
So let's first fix the regression reported by Andrew by making CPU1 reset
conditional. To do this, we need to:
1. Save configured AUX_CORE_BOOT_1 for later
2. Modify AUX_CORE_BOOT_0 reading code to for HS SoCs to return
the whole register instead of the CPU mask
3. Check if CPU1 is wrongly parked into the booting kernel by the
previous kernel and reset if needed
Fixes: 3251885285e1 ("ARM: OMAP4+: Reset CPU1 properly for kexec")
Reported-by: Andrew F. Davis <afd@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Tested-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
- a couple of OMAP 4.11 regression fixes, including a boot regression
for SmartReflex, hypervisor mode in thumb2 mode, and reference
counting of device nodes
- a fix for cpu_idle on at91
- minor DT fixes on across several platforms: sunxi, bcm53xx, at91,
nsp, ns2, ux500, omap
- a fix to correct an API change in the reset controllers
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: dts: NS2: Add dma-coherent to relevant DT entries
reset: fix optional reset_control_get stubs to return NULL
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: dts: NSP: GPIO reboot open-source
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
ARM: dts: add the AB8500 clocks to the device tree
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
ARM: sun8i: Fix the mali clock rate
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
...
|
|
http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom arm Device Tree fixes for 4.11 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
* tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: GPIO reboot open-source
|
|
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Though cpsw doesn't support EEE feature, Atheros 8035 provides
automatic EEE support that is enabled by default. This causes
occasional link drops when link partner also announces EEE support.
These link drops occur on both 100Mbit/s and 1000Mbit/s speeds.
So disable EEE advertising completely.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The manufacturing information is stored in the EEPROM. This chip
is an AT24C64 not not (nor has it ever been) 24C02. This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).
Fixes: 5e3447a29a38 ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OPP are declared as shared but no operating points are declared for
cpu1, 2 and 3. Thus, the following error happens during the boot:
cpu cpu1: dev_pm_opp_of_get_sharing_cpus: Couldn't find tcpu_dev node.
This patch applies the operating points to each cpu of the A33.
Fixes: 03749eb88e63 ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Fixes for 4.11:
- Fix USB host for sama5d2
- Fix cpuidle on sama5
* tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.11
A bunch of device tree fixes for various boards / SoCs.
* tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: sun8i: Fix the mali clock rate
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.11:
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
* tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
kprobes test cases need to have a stack that is aligned to an 8-byte
boundary because they call other functions (and the ARM ABI mandates
that alignment) and because test cases include 64-bit accesses to the
stack. Unfortunately, GCC doesn't ensure this alignment for inline
assembler and for the code in question seems to always misalign it by
pushing just the LR register onto the stack. We therefore need to
explicitly perform stack alignment at the start of each test case.
Without this fix, some test cases will generate alignment faults on
systems where alignment is enforced. Even if the kernel is configured to
handle these faults in software, triggering them is ugly. It also
exposes limitations in the fault handling code which doesn't cope with
writes to the stack. E.g. when handling this instruction
strd r6, [sp, #-64]!
the fault handling code will write to a stack location below the SP
value at the point the fault occurred, which coincides with where the
exception handler has pushed the saved register context. This results in
corruption of those registers.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
This is arm port of commit 737480a0d525 ("kprobes/x86:
Fix the return address of multiple kretprobes").
Fix the return address of subsequent kretprobes when multiple
kretprobes are set on the same function.
For example:
# cd /sys/kernel/debug/tracing
# echo "r:event1 sys_symlink" > kprobe_events
# echo "r:event2 sys_symlink" >> kprobe_events
# echo 1 > events/kprobes/enable
# ln -s /tmp/foo /tmp/bar
(without this patch)
# cat trace | grep -v ^#
ln-82 [000] dn.2 68.446525: event1: (kretprobe_trampoline+0x0/0x18 <- SyS_symlink)
ln-82 [000] dn.2 68.447831: event2: (ret_fast_syscall+0x0/0x1c <- SyS_symlink)
(with this patch)
# cat trace | grep -v ^#
ln-81 [000] dn.1 39.463469: event1: (ret_fast_syscall+0x0/0x1c <- SyS_symlink)
ln-81 [000] dn.1 39.464701: event2: (ret_fast_syscall+0x0/0x1c <- SyS_symlink)
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: KUMANO Syuhei <kumano.prog@gmail.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
Kprobes/arm skips single-stepping (moreover handling the event)
if the conditional instruction must not be executed. This
also apply the rule when we hit the recursing kprobe, so
that kprobe does not count nmissed up in that case.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
This is arm port of commit 6a5022a56ac3 ("kprobes/x86: Allow to
handle reentered kprobe on single-stepping")
Since the FIQ handlers can interrupt in the single stepping
(or preparing the single stepping, do_debug etc.), we should
consider a kprobe is hit in the NMI handler. Even in that
case, the kprobe is allowed to be reentered as same as the
kprobes hit in kprobe handlers
(KPROBE_HIT_ACTIVE or KPROBE_HIT_SSDONE).
The real issue will happen when a kprobe hit while another
reentered kprobe is processing (KPROBE_REENTER), because
we already consumed a saved-area for the previous kprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
|
|
The highest supported frequency (1.2GHz) requires to "overvolt" the CPU.
However, some boards still do not have the cpu-supply DT property in the
cpu DT node which means that the CPU will always run with the same input
voltage but try to run at 1.2GHz frequency. This is the source of
(experienced) CPU crashes.
Remove the OPP which requires overvolting the CPU until all boards have
a cpu-supply property.
Fixes: 03749eb88e63 ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The digital AIF interfaces has been renamed in the sun8i audio codec
driver so the audio-routing in the device tree must be renamed too.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We don't hold the mmap_sem while searching for VMAs (via find_vma), in
kvm_arch_prepare_memory_region, which can end up in expected failures.
Fixes: commit 8eef91239e57 ("arm/arm64: KVM: map MMIO regions at creation time")
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Eric Auger <eric.auger@rehat.com>
Cc: stable@vger.kernel.org # v3.18+
Reviewed-by: Christoffer Dall <cdall@linaro.org>
[ Handle dirty page logging failure case ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We don't hold the mmap_sem while searching for the VMAs when
we try to unmap each memslot for a VM. Fix this properly to
avoid unexpected results.
Fixes: commit 957db105c997 ("arm/arm64: KVM: Introduce stage2_unmap_vm")
Cc: stable@vger.kernel.org # v3.19+
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The bl_en_pin GPIO pinmux is configured as "gpio_in", which makes it
conflicts with the real GPIO usage (out), and makes the backlight not
usable.
Drop the GPIO pinmux for it, thus this GPIO can be correctly used.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f0c ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Pull ARM fix from Russell King:
"Just one change to add the statx syscall this time around"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: wire up statx syscall
|
|
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
On some DDR controllers, compatible with the sama5d3 one,
the sequence to enter/exit/re-enter the self-refresh mode adds
more constrains than what is currently written in the at91_idle
driver. An actual access to the DDR chip is needed between exit
and re-enter of this mode which is somehow difficult to implement.
This sequence can completely hang the SoC. It is particularly
experienced on parts which embed a L2 cache if the code run
between IDLE calls fits in it...
Moreover, as the intention is to enter and exit pretty rapidly
from IDLE, the power-down mode is a good candidate.
So now we use power-down instead of self-refresh. As we can
simplify the code for sama5d3 compatible DDR controllers,
we instantiate a new sama5d3_ddr_standby() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v4.1+
Fixes: 017b5522d5e3 ("ARM: at91: Add new binding for sama5d3-ddramc")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.11-rc cycle:
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
* tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
ARM: OMAP5 / DRA7: Fix HYP mode boot for thumb2 build
ARM: OMAP3: Fix smartreflex platform data regression
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for 4.11,
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
* tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This adds the AB8500 clocks to the device tree using the new
bindings from the clk subsystem, making audio work again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull KVM fixes from Radim Krčmář:
"ARM updates from Marc Zyngier:
- vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
- I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
PCIe devices
- General bug fixes:
- Gracefully handle exception generated with syndroms that the host
doesn't understand
- Properly invalidate TLBs on VHE systems
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
reset
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: do not warn when MSR bitmap address is not backed
KVM: arm64: Increase number of user memslots to 512
KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
arm64: KVM: Survive unknown traps from guests
arm: KVM: Survive unknown traps from guests
KVM: arm/arm64: Let vcpu thread modify its own active state
KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs
|
|
Wire up the new statx syscall for ARM.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
If an architecture uses 4level-fixup.h we don't need to do anything as
it includes 5level-fixup.h.
If an architecture uses pgtable-nop*d.h, define __ARCH_USE_5LEVEL_HACK
before inclusion of the header. It makes asm-generic code to use
5level-fixup.h.
If an architecture has 4-level paging or folds levels on its own,
include 5level-fixup.h directly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
arm/arm64 architecture doesnt use private memslots, hence removing
KVM_PRIVATE_MEM_SLOTS macro definition.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Return KVM_USER_MEM_SLOTS for userspace capability query on
NR_MEMSLOTS.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
After issuing a 'reboot' command the imx6sx-udoo-neo board does not
reboot as expected and it just hangs instead.
In mainline kernel only LDO enabled mode is supported. Do not provide
arm-supply/soc-supply nodes in the device tree, so that the board operates
in LDO enabled mode and can then successfully reboot via watchdog.
Fixes: 76e691fc7653b85d39 ("ARM: dts: imx6sx: Add UDOO Neo support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"Two tiny implementations of the DMA API for callback in ARM (for Xen)"
* 'stable/for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb-xen: implement xen_swiotlb_get_sgtable callback
swiotlb-xen: implement xen_swiotlb_dma_mmap callback
|
|
Currently we BUG() if we see a HSR.EC value we don't recognise. As
configurable disables/enables are added to the architecture (controlled
by RES1/RES0 bits respectively), with associated synchronous exceptions,
it may be possible for a guest to trigger exceptions with classes that
we don't recognise.
While we can't service these exceptions in a manner useful to the guest,
we can avoid bringing down the host. Per ARM DDI 0406C.c, all currently
unallocated HSR EC encodings are reserved, and per ARM DDI
0487A.k_iss10775, page G6-4395, EC values within the range 0x00 - 0x2c
are reserved for future use with synchronous exceptions, and EC values
within the range 0x2d - 0x3f may be used for either synchronous or
asynchronous exceptions.
The patch makes KVM handle any unknown EC by injecting an UNDEFINED
exception into the guest, with a corresponding (ratelimited) warning in
the host dmesg. We could later improve on this with with a new (opt-in)
exit to the host userspace.
Cc: Dave Martin <dave.martin@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
