| Age | Commit message (Collapse) | Author |
|---|
|
Add watchdog device node for rk322x SoC.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Refer to Chapter 5.3.2 of rk3229 TRM, we can see that GPIO1A[2,4,5]
using RK_FUNC_2 not RK_FUNC_1. This patch fixes it.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adds a new node to the LEGO MINDSTORMS EV3 device tree for the battery.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor headline fix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
If we have Linux installed in eMMC we can boot without
µSD card, but inserting one is not recognised.
The reason is that the card detect gpio (gpio5_152)
is not configured and attached to the mmc1 interface
driver and the mmc driver does not poll by default.
Hence we add pinmux and gpio setup for the SDCARD_NCD
signal.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Droid 4 has WL 1285C connected to the OMAP's UART4 port, which is
used for Bluetooth and most likely can also be used for controlling
the FM radio and GPS receivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
We don't want to use the OTG controller block on this
platform as it limits host mode to high-speed. Instead
we rely on extcon framework to give us ID events for
dual-role mode detection.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix commit 05c4ffc3a266 ("ARM: dts: LogicPD Torpedo: Add MT9P031 Support")
In the previous commit, I indicated that the only testing was done by
showing the camera showed up when probing. This patch fixes an incorrect
pin muxing on cam_d0, cam_d1 and cam_d2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CEC pin was always pulled up, making it impossible to use it.
Change to PIN_INPUT so it can be used by the new CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The clock polarity setting of the mcbsp connected to
the modem was wrong so almost only noise
was received.
With this patch it is also the same as it was on
earlier non-dt kernels where it was working properly
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add power hold and power controller properties to palmas node.
This is needed to shutdown pmic correctly on boards with
powerhold set.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
During my research I found that some of the requirements for the memory
buffers for MFC v6+ devices were blindly copied from the previous (v5)
version and simply turned out to be excessive. The relaxed requirements
are applied by the recent patches to the MFC driver and the driver is
now fully functional even without the reserved memory blocks for all
v6+ variants. This patch removes those reserved memory nodes from all
boards having MFC v6+ hardware block.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
pm_fake doesn't quite describe what the handler does (ignoring writes
and returning 0 for reads).
As we're about to use it (a lot) in a different context, rename it
with a (admitedly cryptic) name that make sense for all users.
Signed-off-by: Zhichao Huang <zhichao.huang@linaro.org>
Reviewed-by: Alex Bennee <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
Hardware debugging in guests is not intercepted currently, it means
that a malicious guest can bring down the entire machine by writing
to the debug registers.
This patch enable trapping of all debug registers, preventing the
guests to access the debug registers. This includes access to the
debug mode(DBGDSCR) in the guest world all the time which could
otherwise mess with the host state. Reads return 0 and writes are
ignored (RAZ_WI).
The result is the guest cannot detect any working hardware based debug
support. As debug exceptions are still routed to the guest normal
debug using software based breakpoints still works.
To support debugging using hardware registers we need to implement a
debug register aware world switch as well as special trapping for
registers that may affect the host state.
Cc: stable@vger.kernel.org
Signed-off-by: Zhichao Huang <zhichao.huang@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
We like living dangerously. Nothing explicitely forbids stack-protector
to be used in the HYP code, while distributions routinely compile their
kernel with it. We're just lucky that no code actually triggers the
instrumentation.
Let's not try our luck for much longer, and disable stack-protector
for code living at HYP.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
The aa104xd12 and aa121td01 panels are LVDS panels, not DPI panels.
Use the correct DT bindings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1,2}.
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Define the upper limit otherwise the driver cannot utilize max speeds.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add node for the GyroADC block and it's associated clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This adds the USB0 and USB1 clocks to the device tree.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6050000.pfc and pfc@e6050000 to
e6050000.pin-controller and pin-controller@e6050000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from fffc0000.pfc and pfc@fffc0000 to
fffc0000.pin-controller and pin-controller@fffc0000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from fffc0000.pfc and pfc@fffc0000 to
fffc0000.pin-controller and pin-controller@fffc0000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6050000.pfc and pfc@e6050000 to
e6050000.pin-controller and pin-controller@e6050000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6050000.pfc and pfc@e6050000 to
e6050000.pin-controller and pin-controller@e6050000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e0140200.pfc and pfc@e0140200 to
e0140200.pin-controller and pin-controller@e0140200.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Moving most of the shared code to virt/kvm/arm had for consequence
that KVM/ARM doesn't build anymore, because the code that used to
define the tracepoints is now somewhere else.
Fix this by defining CREATE_TRACE_POINTS in coproc.c, and clean-up
trace.h as well.
Fixes: 35d2d5d490e2 ("KVM: arm/arm64: Move shared files to virt/kvm/arm")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
The board file for imx6sx-sdb overrides cpufreq operating points to use
higher voltages. This is done because the board has a shared rail for
VDD_ARM_IN and VDD_SOC_IN and when using LDO bypass the shared voltage
needs to be a value suitable for both ARM and SOC.
This only applies to LDO bypass mode, a feature not present in upstream.
When LDOs are enabled the effect is to use higher voltages than necessary
for no good reason.
Setting these higher voltages can make some boards fail to boot with ugly
semi-random crashes reminiscent of memory corruption. These failures only
happen on board rev. C, rev. B is reported to still work.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 54183bd7f766 ("ARM: imx6sx-sdb: add revb board and make it default")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently the following errors are seen:
[ 14.015056] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.321093] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.411681] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.456281] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 30.527106] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 36.596900] mc13xxx 0-0008: Failed to read IRQ status: -6
Also when reading the interrupts via 'cat /proc/interrupts' the
PMIC GPIO interrupt counter does not stop increasing.
The reason for the storm of interrupts is that the PUS field of
register IOMUXC_SW_PAD_CTL_PAD_CSI0_DAT5 is currently configured as:
10 : 100k pullup
and the PMIC interrupt is being registered as IRQ_TYPE_LEVEL_HIGH type,
which is the correct type as per the MC34708 datasheet.
Use the default power on value for the IOMUX, which sets PUS field as:
00: 360k pull down
This prevents the spurious PMIC interrupts from happening.
Commit e1ffceb078c6 ("ARM: imx53: qsrb: fix PMIC interrupt level")
correctly described the irq type as IRQ_TYPE_LEVEL_HIGH, but
missed to update the IOMUX of the PMIC GPIO as pull down.
Fixes: e1ffceb078c6 ("ARM: imx53: qsrb: fix PMIC interrupt level")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rockchip finally named the SOC as RV1108, so change it
for compatible.
The rk1108/rv1108 is completely new to the market, so there no real
devices exist in the wild, only the Rockchip internal evaluation
board. Therefore we're not breaking any existing devices when
changing compatible values.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
[added paragraph about no real devices existing]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Rockchip finally named the SOC as RV1108, so change it
for compatible.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapt include in rk1108-evb.dts to not introduce errors]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This pull request brings back bcm2835 DT fixups from Baruch Siach that
got misplaced after a PR for 4.11 got rejected.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Now that the rockchip usb phy has a vbus-supply property use that to
control the vbus regulator on rock2.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence first allocation with CONFIG_ARM64_MODULE_PLTS=y
ARM: Silence first allocation with CONFIG_ARM_MODULE_PLTS=y
mm: Silence vmap() allocation failures based on caller gfp_flags
arm64: uaccess: suppress spurious clang warning
arm64: atomic_lse: match asm register sizes
arm64: armv8_deprecated: ensure extension of addr
arm64: uaccess: ensure extension of access_ok() addr
arm64: ensure extension of smp_store_release value
arm64: xchg: hazard against entire exchange variable
arm64: documentation: document tagged pointer stack constraints
arm64: entry: improve data abort handling of tagged pointers
arm64: hw_breakpoint: fix watchpoint matching for tagged pointers
arm64: traps: fix userspace cache maintenance emulation on a tagged pointer
|
|
When CONFIG_ARM_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild UAPI updates from Masahiro Yamada:
"Improvement of headers_install by Nicolas Dichtel.
It has been long since the introduction of uapi directories, but the
de-coupling of exported headers has not been completed. Headers listed
in header-y are exported whether they exist in uapi directories or
not. His work fixes this inconsistency.
All (and only) headers under uapi directories are now exported. The
asm-generic wrappers are still exceptions, but this is a big step
forward"
* tag 'kbuild-uapi-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
arch/include: remove empty Kbuild files
uapi: export all arch specifics directories
uapi: export all headers under uapi directories
smc_diag.h: fix include from userland
btrfs_tree.h: fix include from userland
uapi: includes linux/types.h before exporting files
Makefile.headersinst: remove destination-y option
Makefile.headersinst: cleanup input files
x86: stop exporting msr-index.h to userland
nios2: put setup.h in uapi
h8300: put bitsperlong.h in uapi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull misc Kbuild updates from Masahiro Yamada:
- clean up builddeb script
- use full path for KBUILD_IMAGE to fix rpm-pkg build
- fix objdiff tool to ignore debug info
* tag 'kbuild-misc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
builddeb: fix typo
builddeb: Update a few outdated and hardcoded strings
deb-pkg: Remove the KBUILD_IMAGE workaround
unicore32: Use full path in KBUILD_IMAGE definition
sh: Use full path in KBUILD_IMAGE definition
arc: Use full path in KBUILD_IMAGE definition
arm: Use full path in KBUILD_IMAGE definition
arm64: Use full path in KBUILD_IMAGE definition
scripts: objdiff: Ignore debug info when comparing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
|
|
Pull more KVM updates from Paolo Bonzini:
"ARM:
- bugfixes
- moved shared 32-bit/64-bit files to virt/kvm/arm
- support for saving/restoring virtual ITS state to userspace
PPC:
- XIVE (eXternal Interrupt Virtualization Engine) support
x86:
- nVMX improvements, including emulated page modification logging
(PML) which brings nice performance improvements on some workloads"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (45 commits)
KVM: arm/arm64: vgic-its: Cleanup after failed ITT restore
KVM: arm/arm64: Don't call map_resources when restoring ITS tables
KVM: arm/arm64: Register ITS iodev when setting base address
KVM: arm/arm64: Get rid of its->initialized field
KVM: arm/arm64: Register iodevs when setting redist base and creating VCPUs
KVM: arm/arm64: Slightly rework kvm_vgic_addr
KVM: arm/arm64: Make vgic_v3_check_base more broadly usable
KVM: arm/arm64: Refactor vgic_register_redist_iodevs
KVM: Add kvm_vcpu_get_idx to get vcpu index in kvm->vcpus
nVMX: Advertise PML to L1 hypervisor
nVMX: Implement emulated Page Modification Logging
kvm: x86: Add a hook for arch specific dirty logging emulation
kvm: nVMX: Validate CR3 target count on nested VM-entry
KVM: set no_llseek in stat_fops_per_vm
KVM: arm/arm64: vgic: Rename kvm_vgic_vcpu_init to kvm_vgic_vcpu_enable
KVM: arm/arm64: Clarification and relaxation to ITS save/restore ABI
KVM: arm64: vgic-v3: KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES
KVM: arm64: vgic-its: Fix pending table sync
KVM: arm64: vgic-its: ITT save and restore
KVM: arm64: vgic-its: Device table save/restore
...
|
|
Regularly, when a new header is created in include/uapi/, the developer
forgets to add it in the corresponding Kbuild file. This error is usually
detected after the release is out.
In fact, all headers under uapi directories should be exported, thus it's
useless to have an exhaustive list.
After this patch, the following files, which were not exported, are now
exported (with make headers_install_all):
asm-arc/kvm_para.h
asm-arc/ucontext.h
asm-blackfin/shmparam.h
asm-blackfin/ucontext.h
asm-c6x/shmparam.h
asm-c6x/ucontext.h
asm-cris/kvm_para.h
asm-h8300/shmparam.h
asm-h8300/ucontext.h
asm-hexagon/shmparam.h
asm-m32r/kvm_para.h
asm-m68k/kvm_para.h
asm-m68k/shmparam.h
asm-metag/kvm_para.h
asm-metag/shmparam.h
asm-metag/ucontext.h
asm-mips/hwcap.h
asm-mips/reg.h
asm-mips/ucontext.h
asm-nios2/kvm_para.h
asm-nios2/ucontext.h
asm-openrisc/shmparam.h
asm-parisc/kvm_para.h
asm-powerpc/perf_regs.h
asm-sh/kvm_para.h
asm-sh/ucontext.h
asm-tile/shmparam.h
asm-unicore32/shmparam.h
asm-unicore32/ucontext.h
asm-x86/hwcap2.h
asm-xtensa/kvm_para.h
drm/armada_drm.h
drm/etnaviv_drm.h
drm/vgem_drm.h
linux/aspeed-lpc-ctrl.h
linux/auto_dev-ioctl.h
linux/bcache.h
linux/btrfs_tree.h
linux/can/vxcan.h
linux/cifs/cifs_mount.h
linux/coresight-stm.h
linux/cryptouser.h
linux/fsmap.h
linux/genwqe/genwqe_card.h
linux/hash_info.h
linux/kcm.h
linux/kcov.h
linux/kfd_ioctl.h
linux/lightnvm.h
linux/module.h
linux/nbd-netlink.h
linux/nilfs2_api.h
linux/nilfs2_ondisk.h
linux/nsfs.h
linux/pr.h
linux/qrtr.h
linux/rpmsg.h
linux/sched/types.h
linux/sed-opal.h
linux/smc.h
linux/smc_diag.h
linux/stm.h
linux/switchtec_ioctl.h
linux/vfio_ccw.h
linux/wil6210_uapi.h
rdma/bnxt_re-abi.h
Note that I have removed from this list the files which are generated in every
exported directories (like .install or .install.cmd).
Thanks to Julien Floret <julien.floret@6wind.com> for the tip to get all
subdirs with a pure makefile command.
For the record, note that exported files for asm directories are a mix of
files listed by:
- include/uapi/asm-generic/Kbuild.asm;
- arch/<arch>/include/uapi/asm/Kbuild;
- arch/<arch>/include/asm/Kbuild.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Salter <msalter@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Pull dmaengine updates from Vinod Koul:
"This time again a smaller update consisting of:
- support for TI DA8xx dma controller and updates to the cppi driver
- updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor,
ioat, dmatest"
* tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (35 commits)
dmaengine: pl08x: remove lock documentation
dmaengine: pl08x: fix pl08x_dma_chan_state documentation
dmaengine: pl08x: Use the BIT() macro consistently
dmaengine: pl080: Fix some missing kerneldoc
dmaengine: pl080: Cut some unused defines
dmaengine: dmatest: Add check for supported buffer count (sg_buffers)
dmaengine: dmatest: Select DMA_ENGINE_RAID as its needed for the slave_sg test
dmaengine: virt-dma: Convert to use list_for_each_entry_safe()
dma-debug: use offset_in_page() macro
dmaengine: mv_xor: use offset_in_page() macro
dmaengine: dmatest: use offset_in_page() macro
dmaengine: sun4i: fix invalid argument
dmaengine: ioat: use setup_timer
dmaengine: cppi41: Fix an Oops happening in cppi41_dma_probe()
dmaengine: pl330: remove pdata based initialization
dmaengine: cppi: fix build error due to bad variable
dmaengine: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
dmaengine: cppi41: use managed functions devm_*()
dmaengine: cppi41: fix cppi41_dma_tx_status() logic
dmaengine: qcom_hidma: pause the channel on shutdown
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
|
|
fixes
Pull "DTS fixes" from Matthias Brugger:
- mt8173: fix mmc parameters
- set timer frequency explicitly and force the driver to set it
* tag 'v4.11-next-fixes' of https://github.com/mbgg/linux-mediatek:
ARM64: dts: mediatek: configure some fixed mmc parameters
arm: dts: mt7623: add clock-frequency to the a7 timer node to mt7623.dtsi
|
|
When CONFIG_PM is disabled, we get a build error:
arch/arm/mach-omap2/omap-smp.c: In function 'omap4_smp_maybe_reset_cpu1':
arch/arm/mach-omap2/omap-smp.c:309:20: error: implicit declaration of function 'omap4_get_cpu1_ns_pa_addr'; did you mean 'omap4_get_scu_base'? [-Werror=implicit-function-declaration]
We need to fix this in multiple files, to ensure the declaration is visible,
to actually build the function without CONFIG_PM, and to only call it
when OMAP4 and/or OMAP5 are enabled.
Fixes: 351b7c490700 ("ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
|
