| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: rx51: fix USB
ARM: OMAP: mcbsp: Fix possible memory corruption
arm/imx: fix power button on imx51 babbage board
ARM: imx: fix cpufreq build errors
ARM: mx5: add __initconst for fec pdata
MXC PWM: should active during DOZE/WAIT/DBG mode
ARM: EXYNOS: Fix build error without CONFIG_LOCAL_TIMERS
ARM: EXYNOS: Fix for stall in case of cpu hotplug or sleep
ARM: S5PV210: Set 1000ns as PWM backlight period on SMDKV210
ARM: SAMSUNG: remove duplicated header include
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
|
|
The bisection implemented in unwind_find_origin() stopped to early. If
there is only a single entry left to check the original code just took
the end point as origin which might be wrong.
This was introduced in commit de66a979012d ("ARM: 7187/1: fix unwinding
for XIP kernels").
Reported-and-tested-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 10299e2e4e3ed3b16503d4e04edd48b33083f4e2 (ARM: RX-51:
Enable isp1704 power on/off) added power management for isp1704.
However, the transceiver should be powered on by default,
otherwise USB doesn't work at all for networking during
boot.
All kernels after v3.0 are affected.
Cc: stable@kernel.org
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7204/1: arch/arm/kernel/setup.c: initialize arm_dma_zone_size earlier
ARM: 7185/1: perf: don't assign platform_device on unsupported CPUs
ARM: 7187/1: fix unwinding for XIP kernels
ARM: 7186/1: fix Kconfig issue with PHYS_OFFSET and !MMU
|
|
git://git.pengutronix.de/git/imx/linux-2.6 into fixes
|
|
Commits 09d28d ("ARM: OMAP: mcbsp: Start generalize omap2_mcbsp_set_clks_src")
and 7bc0c4 ("ARM: OMAP: mcbsp: Start generalize signal muxing functions")
incorrectly set two struct omap_mcbsp_platform_data fields after
omap_device_build_ss and kfree calls.
Fix this by moving these pdata assignments before those calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
arm_dma_zone_size is used by arm_bootmem_free() which is called by
paging_init(). Thus it needs to be set before calling it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
MAINTAINERS: Update amd-iommu F: patterns
iommu/amd: Fix typo in kernel-parameters.txt
iommu/msm: Fix compile error in mach-msm/devices-iommu.c
Fix comparison using wrong pointer variable in dma debug code
|
|
Since commit 6571534 (plat-mxc: iomux-v3.h: implicitly enable
pull-up/down when that's desired) was in, the power button on imx51
babbage board stopped working because it's pulled up by mistake.
The patch removes the pull-up setting from the pad configuration for
that gpio to make the power button back to work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
CC arch/arm/plat-mxc/cpufreq.o
arch/arm/plat-mxc/cpufreq.c:203: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:203: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:203: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
arch/arm/plat-mxc/cpufreq.c:203: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:204: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:204: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:204: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
arch/arm/plat-mxc/cpufreq.c:204: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:205: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:205: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:205: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
arch/arm/plat-mxc/cpufreq.c:205: warning: function declaration isn't a prototype
make[1]: *** [arch/arm/plat-mxc/cpufreq.o] Error 1
make: *** [arch/arm/plat-mxc] Error 2
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Jason Chen <jason.chen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: sa1100: fix build error
ARM: OMAP1: recalculate loops per jiffy after dpll1 reprogram
ARM: davinci: dm365 evm: align nand partition table to u-boot
ARM: davinci: da850 evm: change audio edma event queue to EVENTQ_0
ARM: davinci: dm646x evm: wrong register used in setup_vpif_input_channel_mode
ARM: davinci: dm646x does not have a DSP domain
ARM: davinci: psc: fix incorrect offsets
ARM: davinci: psc: fix incorrect mask
ARM: mx28: LRADC macro rename
arm: mx23: recognise stmp378x as mx23
ARM: mxs: fix machines' initializers order
ARM: mxs/tx28: add __initconst for fec pdata
ARM: S3C64XX: Staticise s3c6400_sysclass
ARM: S3C64XX: Add linux/export.h to dev-spi.c
ARM: S3C64XX: Remove extern from definition of framebuffer setup call
MAINTAINERS: Extend Samsung patterns to cover SPI and ASoC drivers
MAINTAINERS: Add linux-samsung-soc mailing list for Samsung
MAINTAINERS: Consolidate Samsung MAINTAINERS
ARM: CSR: PM: fix build error due to undeclared 'THIS_MODULE'
ARM: CSR: fix build error due to new mdesc->dma_zone_size
...
|
|
|
|
arm-eabi-4.4.3-ld:--defsym zreladdr=: syntax error
make[2]: *** [arch/arm/boot/compressed/vmlinux] Error 1
make[1]: *** [arch/arm/boot/compressed/vmlinux] Error 2
make: *** [uImage] Error 2
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
|
|
arch/arm/mach-exynos/mct.c: In function 'exynos4_timer_resources':
arch/arm/mach-exynos/mct.c:450: error: 'exynos4_mct_tick_isr' undeclared (first use in this function)
arch/arm/mach-exynos/mct.c:450: error: (Each undeclared identifier is reported only once
arch/arm/mach-exynos/mct.c:450: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-exynos/mct.o] Error 1
Reported-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
|
|
This patch adds remove_irq in place of disable_irq which
is correct equivalent function for setup_irq used in
exynos4_mct_tick_init.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Tested-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The SMDK board uses LT3591 as backlight LED driver of LTE480WV LCD.
According to the LT3591 datasheet, the switching frequency should
be 1MHz. So, PWM period is calculated by following formula:
PWM period = 1/switching frequency
= 1/1MHz
= 1000ns
Thus, the PWM backlight period should be 1000ns.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch removes duplicated slab header for pwm backlight.
arch/arm/plat-samsung/dev-backlight.c: slab.h is included
more than once.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
|
|
fixes
|
|
into fixes
|
|
git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel into fixes
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
|
|
|
|
In the unlikely case that a platform registers a PMU platform_device
when running on a CPU that is unsupported by perf, we will encounter a
NULL dereference when trying to assign the platform_device to the
cpu_pmu structure.
This patch checks that the CPU is supported by perf before assigning
the platform_device.
Reported-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The linker places the unwind tables in readonly sections. So when using
an XIP kernel these are located in ROM and cannot be modified.
For that reason the current approach to convert the relative offsets in
the unwind index to absolute addresses early in the boot process doesn't
work with XIP.
The offsets in the unwind index section are signed 31 bit numbers and
the structs are sorted by this offset. So it first has offsets between
0x40000000 and 0x7fffffff (i.e. the negative offsets) and then offsets
between 0x00000000 and 0x3fffffff. When seperating these two blocks the
numbers are sorted even when interpreting the offsets as unsigned longs.
So determine the first non-negative entry once and track that using the
new origin pointer. The actual bisection can then use a plain unsigned
long comparison. The only thing that makes the new bisection more
complicated is that the offsets are relative to their position in the
index section, so the key to search needs to be adapted accordingly in
each step.
Moreover several consts are added to catch future writes and rename the
member "addr" of struct unwind_idx to "addr_offset" to better match the
new semantic. (This has the additional benefit of breaking eventual
users at compile time to make them aware of the change.)
In my tests the new algorithm was a tad faster than the original and has
the additional upside of not needing the initial conversion and so saves
some boot time and it's possible to unwind even earlier.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 1b9f95f8ade9 (ARM: prepare for removal of a bunch of <mach/memory.h>
files) introduced CONFIG_PHYS_OFFSET but the Kconfig hex prompt did not
provide a default value.
This has the undesired side effect of breaking a reportedly used
trick for updating defconfigs on the fly for routine buildtesting
across all arch and all platforms, i.e.
cp /path/to/somedefconfig .config ; yes "" | make oldconfig
because the config system will endlessly loop until a valid address is
provided.
However we can't just pick a random default value since it is likely to
be wrong for the majority of the boards as the right answer for this
option is quite varied. So the fact that the config system insists on
having a proper value be entered is actually a good thing.
It turns out that only at91x40_defconfig has this problem because it has
CONFIG_MMU=n. However, in the !MMU case, there is already a CONFIG_DRAM_BASE
value that can be used here. So let's use that as a default in that case
and suppress the redundant CONFIG_PHYS_OFFSET prompt.
Eventually the DRAM_BASE config option could simply be replaced by
PHYS_OFFSET directly, but that's a larger change better suited for later.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix compile error due to missing <linux/module.h> include.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix loss of notification with multi-event
perf, x86: Force IBS LVT offset assignment for family 10h
perf, x86: Disable PEBS on SandyBridge chips
trace_events_filter: Use rcu_assign_pointer() when setting ftrace_event_call->filter
perf session: Fix crash with invalid CPU list
perf python: Fix undefined symbol problem
perf/x86: Enable raw event access to Intel offcore events
perf: Don't use -ENOSPC for out of PMU resources
perf: Do not set task_ctx pointer in cpuctx if there are no events in the context
perf/x86: Fix PEBS instruction unwind
oprofile, x86: Fix crash when unloading module (nmi timer mode)
oprofile: Fix crash when unloading module (hr timer mode)
|
|
Otherwise timing is inaccurate, resulting in devices which depend on it,
like omap-keypad, broken.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Current partition information maintained in kernel does not match with
u-boot, this leads to corruption of u-boot env when we update uImage
from kernel. Patch fixes it to match with u-boot partition information.
Signed-off-by: Shankarmurthy,Akshay <akshay.s@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
On OMAP-L138 platform, EDMA event queue 0 should be used for audio
transfers so that they are not starved by video data moving on event queue 1.
Commit 48519f0ae03bc7e86b3dc93e56f1334d53803770 (ASoC: davinci: let platform
data define edma queue numbers) had a side-effect of changing this behavior
by making the driver actually honor the platform data passed.
Fix this now by passing event queue 0 as the queue to be used for audio
transfers.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: <stable@vger.kernel.org> # v2.6.36.x and above
|
|
The function setup_vpif_input_channel_mode() used the VSCLKDIS register
instead of VIDCLKCTL. This meant that when in HD mode videoport channel 0
used a different clock from channel 1.
Clearly a copy-and-paste error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org
|
|
Fix the incorrect classification of DSP clock into a
seperate DSP domain on DM646x.
Per the reference guide (http://www.ti.com/lit/ug/spruep9e/spruep9e.pdf)
there is only one "AlwaysON" power domain on DM6467.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Seperate PDSTAT and PDCTL registers are defined for
domain 0 and domain 1 where as the code always reads
the domain 0 PDSTAT register and domain 1 PDCTL register.
Fix this issue. While at it, introduce usage of macros
for register masks to improve readability.
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
There are 5 LSB bits defined in PDSTAT and the code
currently uses a mask of 1 bit to check the status.
Use a proper mask per the hardware specification.
While at it, use a #define for the mask to improve
readability.
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
It's a correction of two macro names, renaming them from IRADC to LRADC.
Signed-off-by: Peter Rusko <rusko.peter@prolan.hu>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Adding the machine_is_* line was forgotten when converting mach-stmp378x to
mach-mxs.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@kernel.org
|
|
Initializers of m28evk and stmp378x_devb fixed to be in order
they are called.
reference: http://article.gmane.org/gmane.linux.ports.arm.omap/50721
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The symbol is not exported and doesn't need to be.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This is required for the EXPORT_SYMBOL()s the code uses, previously the
header was being included implicitly by another header.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The extern is only useful on prototypes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
In the new kernel, we will get the following compile error:
arch/arm/mach-prima2/pm.c:141: error: 'THIS_MODULE' undeclared
here (not in a function)
so include module.h head file explicitly
Signed-off-by: Barry Song <baohua.song@csr.com>
|
|
commit 98b0124f0e2b88
"ARM: mach-prima2: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size"
causes building error:
arch/arm/mach-prima2/prima2.c:39:19: error: 'SZ_256M' undeclared here
(not in a function)
Signed-off-by: Barry Song <baohua.song@csr.com>
|
|
Use the exact value found in omap1_rate_table, otherwise I have been
experiencing issues with correct timekeeping on my Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
