Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
|
|
Pull ARM Device-tree updates from Olof Johansson:
"New SoCs:
- Atmel/Microchip SAM9X60 (ARM926 SoC)
- OMAP 37xx gets split into AM3703/AM3715/DM3725, who are all
variants of it with different GPU/media IP configurations.
- ST stm32mp15 SoCs (1-2 Cortex-A7, CAN, GPU depending on SKU)
- ST Ericsson ab8505 (variant of ab8500) and db8520 (variant of
db8500)
- Unisoc SC9863A SoC (8x Cortex-A55 mobile chipset w/ GPU, modem)
- Qualcomm SC7180 (8-core 64bit SoC, unnamed CPU class)
New boards:
- Allwinner:
+ Emlid Neutis SoM (H3 variant)
+ Libre Computer ALL-H3-IT
+ PineH64 Model B
- Amlogic:
+ Libretech Amlogic GX PC (s905d and s912-based variants)
- Atmel/Microchip:
+ Kizboxmini, sam9x60 EK, sama5d27 Wireless SOM (wlsom1)
- Marvell:
+ Armada 385-based SolidRun Clearfog GTR
- NXP:
+ Gateworks GW59xx boards based on i.MX6/6Q/6QDL
+ Tolino Shine 3 eBook reader (i.MX6sl)
+ Embedded Artists COM (i.MX7ULP)
+ SolidRun CLearfog CX/ITX and HoneyComb (LX2160A-based systems)
+ Google Coral Edge TPU (i.MX8MQ)
- Rockchip:
+ Radxa Dalang Carrier (supports rk3288 and rk3399 SOMs)
+ Radxa Rock Pi N10 (RK3399Pro-based)
+ VMARC RK3399Pro SOM
- ST:
+ Reference boards for stm32mp15
- ST Ericsson:
+ Samsung Galaxy S III mini (GT-I8190)
+ HREF520 reference board for DB8520
- TI OMAP:
+ Gen1 Amazon Echo (OMAP3630-based)
- Qualcomm:
+ Inforce 6640 Single Board Computer (msm8996-based)
+ SC7180 IDP (SC7180-based)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (623 commits)
dt-bindings: fix compilation error of the example in marvell,mmp3-hsic-phy.yaml
arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
arm64: dts: ti: k3-am65-main Add CAL node
arm64: dts: ti: k3-j721e-main: Add McASP nodes
arm64: dts: ti: k3-am654-main: Add McASP nodes
arm64: dts: ti: k3-j721e: DMA support
arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
arm64: dts: ti: k3-am65: DMA support
arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
ARM: dts: aspeed: rainier: Add UCD90320 power sequencer
ARM: dts: aspeed: rainier: Switch PSUs to unknown version
arm64: dts: rockchip: Kill off "simple-panel" compatibles
ARM: dts: rockchip: Kill off "simple-panel" compatibles
arm64: dts: rockchip: rename dwmmc node names to mmc
ARM: dts: rockchip: rename dwmmc node names to mmc
arm64: dts: exynos: Rename Samsung and Exynos to lowercase
arm64: dts: uniphier: add reset-names to NAND controller node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The changes are a real mixed bag this time around.
The only scary looking one from the diffstat is the uapi change to
asm-generic/mman-common.h, but this has been acked by Arnd and is
actually just adding a pair of comments in an attempt to prevent
allocation of some PROT values which tend to get used for
arch-specific purposes. We'll be using them for Branch Target
Identification (a CFI-like hardening feature), which is currently
under review on the mailing list.
New architecture features:
- Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
- Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure
hardware random number generator. As well as exposing these to
userspace, we also use them as part of the KASLR seed and to seed
the crng once all CPUs have come online.
- Advertise a bunch of new instructions to userspace, including
support for Data Gathering Hint, Matrix Multiply and 16-bit
floating point.
Kexec:
- Cleanups in preparation for relocating with the MMU enabled
- Support for loading crash dump kernels with kexec_file_load()
Perf and PMU drivers:
- Cleanups and non-critical fixes for a couple of system PMU drivers
FPU-less (aka broken) CPU support:
- Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck
finding a 64-bit userspace that handles this.
Modern assembly function annotations:
- Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended
to aid debuggers
Kbuild:
- Cleanup detection of LSE support in the assembler by introducing
'as-instr'
- Remove compressed Image files when building clean targets
IP checksumming:
- Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
Hardware errata:
- Work around Cortex-A55 erratum #1530923
Shadow call stack:
- Work around some issues with Clang's integrated assembler not
liking our perfectly reasonable assembly code
- Avoid allocating the X18 register, so that it can be used to hold
the shadow call stack pointer in future
ACPI:
- Fix ID count checking in IORT code. This may regress broken
firmware that happened to work with the old implementation, in
which case we'll have to revert it and try something else
- Fix DAIF corruption on return from GHES handler with pseudo-NMIs
Miscellaneous:
- Whitelist some CPUs that are unaffected by Spectre-v2
- Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
- Reserve a couple of arch-specific PROT flags that are already used
by Sparc and PowerPC and are planned for later use with BTI on
arm64
- Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (73 commits)
arm64: acpi: fix DAIF manipulation with pNMI
arm64: kconfig: Fix alignment of E0PD help text
arm64: Use v8.5-RNG entropy for KASLR seed
arm64: Implement archrandom.h for ARMv8.5-RNG
arm64: kbuild: remove compressed images on 'make ARCH=arm64 (dist)clean'
arm64: entry: Avoid empty alternatives entries
arm64: Kconfig: select HAVE_FUTEX_CMPXCHG
arm64: csum: Fix pathological zero-length calls
arm64: entry: cleanup sp_el0 manipulation
arm64: entry: cleanup el0 svc handler naming
arm64: entry: mark all entry code as notrace
arm64: assembler: remove smp_dmb macro
arm64: assembler: remove inherit_daif macro
ACPI/IORT: Fix 'Number of IDs' handling in iort_id_map()
mm: Reserve asm-generic prot flags 0x10 and 0x20 for arch use
arm64: Use macros instead of hard-coded constants for MAIR_EL1
arm64: Add KRYO{3,4}XX CPU cores to spectre-v2 safe list
arm64: kernel: avoid x18 in __cpu_soft_restart
arm64: kvm: stop treating register x18 as caller save
arm64/lib: copy_page: avoid x18 register in assembler code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC family changes for 5.6, part 2.
- Add DMA nodes for am65x and j721e
- Add McASP nodes for am65x and j721e, showcasing the DMA usage
- Add CAL node for am65x
- Add OV5640 camera support for am65x
* tag 'ti-k3-soc-for-v5.6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
arm64: dts: ti: k3-am65-main Add CAL node
arm64: dts: ti: k3-j721e-main: Add McASP nodes
arm64: dts: ti: k3-am654-main: Add McASP nodes
arm64: dts: ti: k3-j721e: DMA support
arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
arm64: dts: ti: k3-am65: DMA support
arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
Link: https://lore.kernel.org/r/83546942-6215-9c3a-16cd-be7e7c000c0e@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM64 SoC DT updates for v5.6
- Add reset-names to NAND controller node
* tag 'uniphier-dt64-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add reset-names to NAND controller node
Link: https://lore.kernel.org/r/CAK7LNASehDHWgOug=Rz0uBBSP2ntJnNLiarfSdj97tZu+OXLkA@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add support for the OV5640 CSI camera:
- add the OV5640 nodes
- add the CAL node linkage
- enable CAL node
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add CAL dtsi node for AM654 device. Including proper power-domains and
clock properties.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add the nodes for McASP 0-11 and keep them disabled because several
required properties are not present as they are board specific.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add the nodes for McASP 0-2 and keep them disabled because several
required properties are not present as they are board specific.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add the ringacc and udmap nodes for main and mcu NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Secure proxy (NAVSS0_SEC_PROXY0) and smmu (NAVSS0_TCU) is part of the
Navigator Subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
NAVSS is a subsystem containing different IPs, it is not really a bus.
Change the compatible from "simple-bus" to "simple-mfd" to reflect that.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
On am654 the MAIN NAVSS base address was 0x30800000, but in j721e it is
at 0x30000000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add the ringacc and udmap nodes for main and mcu NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Secure proxy (NAVSS0_SEC_PROXY0) is part of the Navigator Subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
NAVSS is a subsystem containing different IPs, it is not really a bus.
Change the compatible from "simple-bus" to "simple-mfd" to reflect that.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
arm/dt
arm64: dts: zynqmp: DT changes for v5.6
- Switch from fixed to firmware based clock driver
- Wire power domain driver
- Wire all ina226 chips through IIO and IIO hwmon drivers
- Add missing dr_mode property to usb nodes
- Use gpio-line-names property instead of comments
- Use clock-output-names for si570 differentiation
- Minor DT fixes
* tag 'zynqmp-dt-for-v5.6' of https://github.com/Xilinx/linux-xlnx: (21 commits)
arm64: zynqmp: Add label property to all ina226 on zcu106
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu106
arm64: zynqmp: Add label property to all ina226 on zcu102
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu102
arm64: zynqmp: Add label property to all ina226 on zcu111
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu111
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu100
arm64: zynqmp: Setup default number of chipselects for zcu100
arm64: zynqmp: Remove broken-cd from zcu100-revC
arm64: zynqmp: Fix the si570 clock frequency on zcu111
arm64: zynqmp: Setup clock-output-names for si570 chips
arm64: zynqmp: Turn comment to gpio-line-names
arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104
arm64: zynqmp: Remove addition number in node name
arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
arm64: dts: xilinx: Add the power nodes for zynqmp
arm64: dts: xilinx: Remove dtsi for fixed clock
arm64: dts: xilinx: Add the clock nodes for zynqmp
arm64: zynqmp: Add dr_mode property to usb node
arm64: dts: zynqmp: Use decimal values for drm-clock properties
...
Link: https://lore.kernel.org/r/c70d2efa-9ee2-a764-5248-0e5bfbf29f8a@monstr.eu
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since v4.3-rc1 commit 0723c05fb75e44 ("arm64: enable more compressed
Image formats"), it is possible to build Image.{bz2,lz4,lzma,lzo}
AArch64 images. However, the commit missed adding support for removing
those images on 'make ARCH=arm64 (dist)clean'.
Fix this by adding them to the target list.
Make sure to match the order of the recipes in the makefile.
Cc: stable@vger.kernel.org # v4.3+
Fixes: 0723c05fb75e44 ("arm64: enable more compressed Image formats")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
DSI display for px30 evaluation board and a number of cleanups
accross multiple socs.
* tag 'v5.6-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Kill off "simple-panel" compatibles
arm64: dts: rockchip: rename dwmmc node names to mmc
arm64: dts: rockchip: hook up the px30-evb dsi display
arm64: dts: rockchip: Enable sdio0 and uart0 on rk3399-roc-pc-mezzanine
arm64: dts: rockchip: add reg property to brcmf sub-nodes
arm64: dts: rockchip: fix dwmmc clock name for rk3308
arm64: dts: rockchip: fix dwmmc clock name for px30
Link: https://lore.kernel.org/r/7641353.lIegmeFAIi@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200117230851.25434-1-robh@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Current dts files with 'dwmmc' nodes are manually verified.
In order to automate this process rockchip-dw-mshc.txt
has to be converted to yaml. In the new setup
rockchip-dw-mshc.yaml will inherit properties from
mmc-controller.yaml and synopsys-dw-mshc-common.yaml.
'dwmmc' will no longer be a valid name for a node,
so change them all to 'mmc'
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200115185244.18149-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Link: https://lore.kernel.org/r/20200117190305.5257-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC family changes for 5.6
- Add missing power domains for smmu for J721e
- Add I2C, ADC, OSPI and UFS nodes for J721e
- Add OSPI and MCU syscon nodes for am65x
- Add IRQ line for GPIO expander on am65x
* tag 'ti-k3-soc-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-j721e-main: Add missing power-domains for smmu
arm64: dts: ti: k3-am65-mcu: add system control module node
arm64: dts: k3-am654-base-board: Add IRQ line for GPIO expander
arm64: dts: ti: k3-am65: Add OSPI DT node
arm64: dts: ti: k3-j721e: Add DT nodes for few peripherials
Link: https://lore.kernel.org/r/c5b74bfc-f2f0-1b72-4a3c-4c1d478a023a@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Denali NAND controller IP has separate reset control for the
controller core and registers.
Add the reset-names, and one more phandle accordingly. This is the
approved DT-binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add power-domains entry for smmu, so that the it is accessible as long
as the driver is active. Without this device shutdown is throwing the
below warning:
"[ 44.736348] arm-smmu-v3 36600000.smmu: failed to clear cr0"
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
The MCU System control module support is added to the device tree to allow
drivers to access to their System control module registers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add IRQ line for IO expander present on wkup_i2c bus on AM654 EVM
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
AM654 SoC has two Cadence OSPI controller instances under Flash
subsystem (FSS). Add DT nodes for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Enable I2Cs, ADCs, OSPIs and UFS peripherals present on J721e.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Remove fixed clock and source common clock for UART controllers.
Link: https://lore.kernel.org/r/20200114040311.6599-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add clock controller support for Bitmain BM1880 SoC.
Link: https://lore.kernel.org/r/20200114040311.6599-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: Amlogic updates for v5.6
- new boards: libretech-pc (S912 and S905D versions)
- new board: Videostrong KII Pro
- A1: add reset controller
* tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: add audio fifo depths
arm64: dts: meson: add libretech-pc boards support
dt-bindings: arm: amlogic: add libretech-pc bindings
arm64: dts: meson: gxl: add i2c C pins
arm64: dts: meson-sm1: add video decoder compatible
arm64: dts: meson-g12-common: add video decoder node
arm64: dts: meson-gxbb: add support for Videostrong KII Pro
dt-bindings: arm: amlogic: add Videostrong KII Pro bindings
dt-bindings: Add vendor prefix for Videostrong
arm64: dts: meson: a1: add pinctrl controller support
arm64: dts: meson: add reset controller for Meson-A1 SoC
Link: https://lore.kernel.org/r/7hsgkidi3k.fsf@baylibre.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for v5.6
* Align SDM845 firmware paths with linux-firmware
* Make WiFi work on Dragonboard845c
* Wire up wakeup controller for SDM845
* Critical thermal interrupt support for SDM845, MSM8996 and MSM8998
* Enable UFS for SM8150
* Add remoteproc enablers and nodes for SM8150
* Add CPUfreq for SM8150
* Add RPMH power-domain node for SM8150
* Cleanup and refactor MSM8996 dts structure
* Add initial Inforce Computing IFC6640 dts
* Increase MSM8996 core voltage
* Fix MSM8996 USB phy settings
* Add missing alias for BLSP UART in MSM8998 MTP
* Add remoteproc nodes for ADSP, modem and sensor core for MSM8998
* Enable WiFI for MSM8998
* Introduce the SC7180 platform and the IDP development board
* Add CPUfreq, QUPs, USB, remoteproc etc for SC7180
* Enable USB OTG for Dragonboard 410c
* Add vibrator motor node for PM8916
* Properly specify APCS clocks for MSM8916
* Add CPR and HFPLL for QCS404
* Enable full CPUfreq (with AVS) for QCS404
* tag 'qcom-arm64-for-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (88 commits)
arm64: dts: qcom: sdm845: move gpu zap nodes to per-device dts
arm64: dts: qcom: sm8150: Hard code rpmhpd constants
arm64: dts: apq8096-db820c: Fix VDD core voltage
arm64: dts: qcom: qcs404-evb: Set vdd_apc regulator in high power mode
arm64: dts: qcom: msm8998-mtp: Add alias for blsp1_uart3
arm64: dts: qcom: sc7180: Add critical interrupt and cooling maps for TSENS in SC7180
arm64: dts: qcom: msm8996: Fix venus iommu nodename error
arm64: dts: qcom: sdm845: add the ufs reset
arm64: dts: qcom: sm8150: Fix UFS phy register size
arm64: dts: qcom: sm8150-mtp: Add UFS gpio reset
arm64: dts: qcom: qcs404: Add CPR and populate OPP table
arm64: dts: qcom: qcs404: Add DVFS support
arm64: dts: qcom: qcs404: Add the clocks for APCS mux/divider
arm64: dts: qcom: qcs404: Add HFPLL node
arm64: dts: qcom: msm8916: Add the clocks for the APCS mux/divider
arm64: dts: qcom: sc7180: Add rpmh power-domain node
arm64: dts: pm8004: Add SPMI regulator and add phandles to lsids
arm64: dts: msm8998: thermal: Add critical interrupt support
arm64: dts: msm8996: thermal: Add critical interrupt support
arm64: dts: qcom: db845c: Move remoteproc firmware to sdm845
...
Link: https://lore.kernel.org/r/20200113204225.GB3325@yoga
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
mt8173:
- add dynamic power coefficient to the cpu clusters
- add jpeg decoder node
mt8183:
- add node for the Global Command Engine (gce)
- add reset cells to the infracfg node
* tag 'v5.5-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: add reset-cells in infracfg
arm64: dts: mt8173: add Mediatek JPEG Codec
arm64: dts: add gce node for mt8183
arm64: dts: mt8173: Add dynamic power node.
Link: https://lore.kernel.org/r/46c1a244-3f74-8069-6600-8ced02775677@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
This is our usual set of DT patches for the Allwinner SoCs.
It's fairly big this time, but the highlights are:
- Enable cpufreq and CPU thermal throttling on the A64
- CLK_CPUX macro usage removed (changed from first pull request)
- CSI0 support on the R40
- CSI1 support on the A10 and A20
- SPI support on the R40
- PMU support on the H3, H5, H6 and R40
- MIPI-DSI support on the A64
- PWM support on the H6
- Thermal sensor on the A64, A83t, H3, H5, H6 and R40
- More DT schemas fixes and conversions
- New boards: LibreComputer ALL-H5-CC H5, LibreComputer ALL-H3-IT H5,
Pine64 H64 Model B, Neutis N5H3
* tag 'sunxi-dt-for-5.6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (52 commits)
arm64: dts: allwinner: a64: enable DVFS
arm64: dts: allwinner: a64: add dtsi with CPU operating points
arm64: dts: allwinner: a64: add cooling maps and thermal tripping points
arm64: dts: allwinner: a64: add CPU clock to CPU0-3 nodes
arm64: dts: allwinner: sun50i-a64: Use macros for newly exported clocks
ARM: dts: sunxi: Use macros for references to CCU clocks
arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board
ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes
arm64: dts: allwinner: a64: pinebook: Fix lid wakeup
ARM: dts: sun8i: r40: Add device node for CSI0
ARM: dts: sun7i: Add CSI1 controller and pinmux options
ARM: dts: sun4i: Add CSI1 controller and pinmux options
ARM: dts: sunxi: Add missing LVDS resets and clocks
ARM: dts: sun8i: r40: Use tcon top clock index macros
ARM: dts: sun8i: R40: Add PMU node
ARM: dts: sun8i: R40: Upgrade GICC reg size to 8K
arm64: dts: allwinner: h6: Add thermal sensor and thermal zones
ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board
arm64: dts: allwinner: a64: Add MIPI DSI pipeline
arm64: dts: allwinner: a64: Add thermal sensors and thermal zones
...
Link: https://lore.kernel.org/r/20200113095555.GA29848@wens.csie.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.6:
- New board support: i.MX8MQ based Thor96 board, Google i.MX8MQ Phanbell
board, LX2160A based Solidrun Clearfog CX and Honeycomb boards.
- Add eLCDIF controller and missing SAI nodes for i.MX8MQ SoC.
- Add Crypto CAAM support for i.MX8MM and i.MX8MN.
- Drop unneeded "simple-bus" from anatop node on i.MX8MM and i.MX8MN.
- Drop unused/undocumented "fsl,aips-bus" and "fsl,imx8mq-aips-bus"
compatibles from i.MX8M SoCs.
- Add DDR controller nodes for i.MX8M devices.
- Add EEPROM description for imx8mq-hummingboard-pulse and
imx8mq-sr-som boards.
- Enable USB1 and TypeC support for imx8mn-evk board.
- Add FlexSPI and QSPI support for a few Layerscape SoCs and boards.
- Add External MDIO1 node and the two RGMII PHYs connected on LX2160A.
- Add missing SAI devices and set SAIs into async mode on LS1028A.
- Other random device additions and enhancement for various platforms.
* tag 'imx-dt64-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (35 commits)
arm64: dts: imx8mn: Memory node should be in board DT
arm64: dts: imx8mm: Memory node should be in board DT
arm64: dts: imx8mn: add crypto node
arm64: dts: imx8mq-hummingboard-pulse: add eeprom description
arm64: dts: imx8mq-sr-som: add eeprom description
arm64: dts: ls208xa: Update qspi node properties for LS2088ARDB
arm64: dts: freescale: Add devicetree support for Thor96 board
arm64: dts: imx8mq-librem5-devkit: add accelerometer and gyro sensor
arm64: dts: imx8mm: Add Crypto CAAM support
arm64: dts: freescale: add initial support for Google i.MX 8MQ Phanbell
arm64: dts: ls1028a-rdb: enable emmc hs400 mode
arm64: dts: ls1028a: Update edma compatible to fit eDMA driver
arm64: dts: imx8m: drop "fsl,aips-bus" and "fsl,imx8mq-aips-bus"
arm64: dts: imx8mm: Add missing mux options for UART1 and UART2 signals
arm64: dts: lx2160a: add dts for CEX7 platforms
arm64: dts: lx2160a: add emdio2 node
arm64: dts: ls1028a: put SAIs into async mode
arm64: dts: ls1028a: add missing sai nodes
arm64: dts: imx8mn-evk: enable usb1 and typec support
arm64: dts: imx8mn: Remove setting for IMX8MN_CLK_USB_CORE_REF
...
Link: https://lore.kernel.org/r/20200113034006.17430-5-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu dt64 for 5.6 (part 1)
micro-DPU (uDPU) board changes (Armada 3270 based board):
- Fix broken ethernet
- Remove i2c-fast-mode property
- Indicate that SFP cages support 3W modules
SolidRun Clearfog GT 8K (Armada 8040 base board):
- Fix switch cpu port node
* tag 'mvebu-dt64-5.6-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: clearfog-gt-8k: fix switch cpu port node
arm64: dts: uDPU: SFP cages support 3W modules
arm64: dts: uDPU: remove i2c-fast-mode
arm64: dts: uDPU: fix broken ethernet
Link: https://lore.kernel.org/r/871rs53nu5.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.6-rc1
These patches do some cleanup to existing nodes, add the memory
subsystem on Tegra186 and Tegra194 as well as the FUSE and APB MISC
nodes on Tegra194. There are also a few additions to the Jetson Nano
device tree to enable additional features and the force recovery
button on the Jetson AGX Xavier now produces a key code that is
actually valid. Finally, an alias is added for the Ethernet card on
Jetson TX2 to allow firmware to find it and pass a MAC address via
device tree.
* tag 'tegra-for-5.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Allow bootloader to configure Ethernet MAC on Jetson TX2
arm64: tegra: Redefine force recovery key on Jetson AGX Xavier
arm64: tegra: Enable SDIO on Jetson Nano M.2 Key E
arm64: tegra: Enable PWM fan on Jetson Nano
arm64: tegra: Add fuse/apbmisc node on Tegra194
arm64: tegra: Make XUSB node consistent with the rest
arm64: tegra: Add the memory subsystem on Tegra194
arm64: tegra: Add external memory controller on Tegra186
arm64: tegra: Add interrupt for memory controller on Tegra186
arm64: tegra: Rename EMC on Tegra132
arm64: tegra: Let the EMC hardware use the EMC clock
Link: https://lore.kernel.org/r/20200111003553.2411874-7-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We want to specify per-device firmware-name, so move the zap node into
the .dts file for individual boards/devices. This lets us get rid of
the /delete-node/ for cheza, which does not use zap.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200112195405.1132288-5-robdclark@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
I missed the fact that these constants was not yet available, so hard
code their values in the dts to make the branch compile on its own.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Create the necessary display nodes to activate the Xingpeng XPP055C272
dsi display that can be found on the px30-evb.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20191209145301.5307-2-heiko@sntech.de
|
|
Include mt8183-reset.h and add reset-cells in infracfg
in dtsi file
Signed-off-by: yong.liang <yong.liang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The mezzanine board carries an E key type M.2 slot. This is
connected to USB, SDIO and UART0. Enable sdio and uart0 for use
with wlan and/or bt M.2 cards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/20200109154211.1530-1-m.reichl@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
An experimental test with the command below gives this error:
rk3399-firefly.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-orangepi.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-captain.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-v.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
So fix this by adding a reg property to the brcmf sub node.
Also add #address-cells and #size-cells to prevent more warnings.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110142128.13522-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
An experimental test with the command below gives this error:
rk3308-evb.dt.yaml: dwmmc@ff480000: clock-names:2:
'ciu-drive' was expected
'ciu-drv' is not a valid dwmmc clock name,
so fix this by changing it to 'ciu-drive'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110161200.22755-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
An experimental test with the command below gives this error:
px30-evb.dt.yaml: dwmmc@ff390000: clock-names:2:
'ciu-drive' was expected
'ciu-drv' is not a valid dwmmc clock name,
so fix this by changing it to 'ciu-drive'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110161200.22755-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add CPU regulator and operating points for all the A64-based boards
that are currently supported to enable DVFS.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Add operating points for A64. These are taken from FEX file from BSP
for A64.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Add cooling maps and thermal tripping points to prevent CPU overheating when
running at the highest frequency. Tripping points are taken from A33 dts since
A64 user manual doesn't mention when we should start throttling.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Add CPU clock to the CPU nodes since it is a prerequisite for enabling
DVFS.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
[wens@csie.org: Replace CLK_CPUX macro with raw number]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|