| Age | Commit message (Collapse) | Author |
|---|
|
The structure rockchip_clk_provider needs to refer the GRF regmap
in somewhere, if the CRU node has not "rockchip,grf" property,
calling syscon_regmap_lookup_by_phandle will return an invalid GRF
regmap, and the MUXGRF type clock will be not supported.
Therefore, we need to add them.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Per the discussion of bug fix[1], we now actually
leaves the default clock choice for pcie phy is
derived from 24MHz OSC to guarantee the least BER.
So let's add aspm-no-l0s here and folks could delete
this property from their dts.
[1] https://patchwork.kernel.org/patch/9470519/
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Per the errata of TRM, rk3399 won't support gen2 from
now on, so let's set max-link-speed to 1 in order not
to doing training for gen2.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Use macros to describe gpios will make the dts easier to
read and write.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[converted interrupt-gpios and new rk3399-evb backlight]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We found that the suspend process was blocked when it run into
ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci
(usb2-phy will be auto suspended if no devices plug-in). and the
clk-480m provided by it was disabled if no module used. However,
some suspend process related ehci/ohci are base on this clock,
so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===
u2phy ________________
| | |-----> UTMI_CLK ---------> | EHCI |
OSC_24M ---|---> PHY_PLL----|----|
|________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC
|
|
GRF
===
Signed-off-by: William wu <wulf@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We haven't enabled eDP support yet, but we might as well describe the
pin now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We're going to need to amend this table in board files.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual
churn in the gadget subsystem and the xhci host controller driver,
along with a few other new small drivers added. And lots of little
other changes all over the USB and PHY driver tree. Full details are
in the shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (309 commits)
USB: serial: option: add dlink dwm-158
USB: serial: option: add support for Telit LE922A PIDs 0x1040, 0x1041
USB: OHCI: nxp: fix code warnings
USB: OHCI: nxp: remove useless extern declaration
USB: OHCI: at91: remove useless extern declaration
usb: misc: rio500: fix result type for error message
usb: mtu3: fix U3 port link issue
usb: mtu3: enable auto switch from U3 to U2
usbip: fix warning in vhci_hcd_probe/lockdep_init_map
usb: core: usbport: Use proper LED API to fix potential crash
usbip: add missing compile time generated files to .gitignore
usb: hcd.h: construct hub class request constants from simpler constants
USB: OHCI: ohci-pxa27x: remove useless functions
USB: OHCI: omap: remove useless extern declaration
USB: OHCI: ohci-omap: remove useless functions
USB: OHCI: ohci-s3c2410: remove useless functions
USB: cdc-acm: add device id for GW Instek AFG-125
fsl/usb: Workarourd for USB erratum-A005697
usb: hub: Wait for connection to be reestablished after port reset
usbip: vudc: Refactor init_vudc_hw() to be more obvious
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "Rockchip dts64 changes for 4.10" from Heiko Stübner:
Some more powerdomains and usb2-otg support for the rk3399 as well
as the binding doc for the 32bit rk1108 eval board to prevent it
from conflicting with the recently added 64bit px5 board.
* tag 'v4.10-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: rockchip: add usb2-phy otg-port support for rk3399
arm64: dts: rockchip: add pd_sd power-domain node for rk3399
arm64: dts: rockchip: add eMMC's power domain support for rk3399
arm64: dts: rockchip: add backlight support for rk3399 evb board
arm64: dts: rockchip: add gmac needed pclk for rk3399 pd
|
|
The "arm,no-tick-in-suspend" property was introduced to note
implementations where the system counter does not quite follow the ARM
specification that it "must be implemented in an always-on power
domain".
Particularly, RK3399's counter stops ticking when we switch from the
24MHz clock to the 32KHz clock in low-power suspend, so let's mark it as
such.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
|
|
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
64bit devicetree changes including the px5 evaluation board
a fix for wrong i2c registers on rk3368 a new nvmem cell and
power-domain on rk3399 as well as moving mmc frequency
properties to the more generic max-frequency one.
* tag 'v4.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
arm64: dts: rockchip: add cpu-id nvmem cell node for rk3399
arm64: dts: rockchip: add sdmmc support for px5-evb
arm64: dts: rockchip: Add more properties for emmc on px5-evb
arm64: dts: rockchip: Add PX5 Evaluation board
arm64: dts: rockchip: add powerdomain for typec on rk3399
arm64: dts: rockchip: fix i2c resource error of rk3368
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add otg-port nodes for both u2phy0 and u2phy1. The otg-port can
be used for USB2.0 part of USB3.0 OTG controller.
Signed-off-by: William Wu <wulf@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the sd power-domain, its qos area and assign it to the
sdmmc device node.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Control power domain for eMMC via genpd to reduce power consumption.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add backlight node for evb board, perpare for panel device node.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch fixes that sometimes hang at start-up time of the system.
As the below log:
...
[ 11.136543] calling pm_genpd_debug_init+0x0/0x60 @ 1
[ 11.141602] initcall pm_genpd_debug_init+0x0/0x60 returned 0 after 11 usecs
[ 11.148558] calling genpd_poweroff_unused+0x0/0x84 @ 1
<hang>
In some cases, the rk3399 should turn off the gmac power domain to save
power if some boards didn't register the gmac device node for rk3399.
Then, rk3399 need to make sure the gmac's pclk enabled if we need
operate the gmac power domain. (Due to the NOC had enabled always)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
|
|
pm_rst, aclk_rst and pclk_rst should be controlled by driver, so we
need to add these three resets for PCIe controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
|
|
In drivers/mmc/core/host.c, there is "max-freqeuncy" property.
It should be same behavior, So Use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
There is a 'cpu-id' field in efuse, export it for other drivers
reference.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
It was invented for sdio only, and should not be used for sdmmc
or emmc. Remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
px5-evb has one sdmmc slot, so we could support sdmmc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The emmc on px5-evb can support hs200, so let's add mmc-hs200-1_8v.
And in order to speed up the boot time, we could add no-sdio and
no-sd to simplify the initialization.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI/BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The tcpc power domain will try to power up/down the power of Type-C PHY.
Hence, we need control it in Type-C PHY driver with the pm_runtime helper.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
According to the TRM and downstream code from rockchip, the register
address of i2c1 on rk3368 is 0xff660000 and i2c2 is 0xff140000.
This patch fix the i2c1 & i2c2 register address definition error, also
fix the clk and pinctrl reference error.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Please don't add these for vcc_sd, and mmc-core/driver will control
it. Otherwise, it will waste energy even without sdmmc in slot.
Moreover, it will causes a bug:
If we insert/remove sd card, we could see
[9.337271] mmc0: new ultra high speed SDR25 SDHC card at address 0007
[9.345144] mmcblk0: mmc0:0007 SD32G 29.3 GiB
This is okay for normal sd insert/remove test, but when I debug some
issues for sdmmc, I did unbind/bind test. And there is a interesting
phenomenon when we bind the driver again:
[58.314069] mmc0: new high speed SDHC card at address 0007
[58.320282] mmcblk0: mmc0:0007 SD32G 29.3 GiB
So the sd card could just support high speed without power cycle
since the vcc_sd is always on, which makes the sd card fail to
reinit its internal ocr mask.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"The 64-bit DT changes are surprisingly small this time, we only add
two SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
UniPhier LD11 TV SoC, each with their reference boards.
There are three new machines added for existing SoC platforms:
- The Marvell Armada 8040 development board is an impressive
quad-core Cortex-A72 machine with three 10gbit ethernet interfaces
- Qualcomms DragonBoard 820c single-board computer is their current
high-end phone platform in the 96boards form factor
- Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
Android box based on the 8-core rk3368 SoC"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (91 commits)
arm64: dts: berlin4ct: Add L2 cache topology
arm64: dts: berlin4ct: enable all wdt nodes unconditionally
arm64: dts: berlin4ct: switch to Cortex-A53 specific pmu nodes
arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
arm64: dts: apm: Add DT node for APM X-Gene 2 CPU clocks
arm64: dts: apm: Add X-Gene SoC hwmon to device tree
arm64: dts: apm: Fix interrupt polarity for X-Gene PCIe legacy interrupts
arm64: dts: apm: Add APM X-Gene v2 SoC PMU DTS entries
arm64: dts: apm: Add APM X-Gene SoC PMU DTS entries
arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
...
|
|
There are 2 Type-C phy on RK3399, they are almost same, except the
address of register. They support USB3.0 Type-C and DisplayPort1.3
Alt Mode on USB Type-C. Register a phy, supply it to USB3 controller
and DP controller.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We add the required and optional properties for evb board.
See the [0] to get the detail information.
[0]:
Documentation/devicetree/bindings/net/rockchip-dwmac.txt
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3399 GMAC Ethernet Controller provides a complete Ethernet interface
from processor to a Reduced Media Independent Interface (RMII) and Reduced
Gigabit Media Independent Interface (RGMII) compliant Ethernet PHY.
This patch adds the related needed device information.
e.g.: interrupts, grf, clocks, pinctrl and so on.
The full details are in [0].
[0]:
Documentation/devicetree/bindings/net/rockchip-dwmac.txt
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds to enable the ARM Performance Monitor Units for rk3399.
ARM cores often have a PMU for counting cpu and cache events like cache
misses and hits.
This uses the new interrupt-partition mechanism to allow the two pmu
instances to use the per-cpu interrupt.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the interrupts cells value for 4, and the 4th cell is zero.
Due to the doc[0] said:" the system requires describing PPI affinity,
then the value must be at least 4"
The 4th cell is a phandle to a node describing a set of CPUs this
interrupt is affine to. The interrupt must be a PPI, and the node
pointed must be a subnode of the "ppi-partitions" subnode. For
interrupt types other than PPI or PPIs that are not partitionned,
this cell must be zero. See the "ppi-partitions" node description
below.
[0]:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The tcpc is the Type C Port Controller and Type C Port Delivery (tcpd)
is part of it, we haven't used them now, add it to save power consumption.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add a efuse0 node in the device tree for the ARM64 rk3399 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Let's assigne slot numbers, ep-gpios and clkreq used by PCIe
on evb board as well the PHY node here. Note that we still
disable them as the auto training of PCIe link will make the
kernel use more time to boot if there are no any devices there.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch introduces PCIe support found on RK3399 platform,
and specify phys phandle for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds PCIe node for RK3399 to support
PCIe controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds the gmac ppower-domain to save power consumption
by letting the driver core handle the power-domain so we can
save power on boards not needing Ethernet.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
On some rk3399 boards GPIO0_A0 is hooked up to a 32 kHz clock. This can
be used as the source for various clocks in the system.
Add a pinmux so boards can get this pin properly configured.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Per testing, this can reduce the memory latency and d8 gets
better scores.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Due to incorrect description in the TRM, the WDTs base address
should be fixed and swap them like this:
WDT0 - 0xff848000
WDT1 - 0xff840000
And, it is right that only WDT0 can generate global software reset.
We will update the TRM to fix it.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds saradc needed information on rk3399 SoCs.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
SARADC controller needs to be reset before programming it, otherwise
it will not function properly.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add vcc5v0_host regulator for usb2-phy and enable host-port support.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add usb2-phy nodes and specify phys phandle for ehci.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
