Age | Commit message (Collapse) | Author |
|
Exynos7
Add @0 unit address to 'soc' node match its 'reg' property and move the
thermal zones out of 'soc' to main root as it this is usually not a
property of a Soc.
This silences DTC warnings:
Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name
Warning (simple_bus_reg): /soc/thermal-zones: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add @0 unit address to 'soc' node match its 'reg' property and silence
DTC warning:
Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
|
|
LDO12 on Exynos7 Espresso board supplies power to VDDQ_UFS20_RESET, in
case this regulator is OFF, UFS host controller can not send command to
UFS device. To keep this supply ON, set regulator-always-on property for
this LDO.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Once regulators are disabled after kernel boot, on Espresso board silent
hang observed because of LDO7 being disabled. LDO7 actually provide
power to CPU cores and non-cpu blocks circuitries. Keep this regulator
always-on to fix this hang.
Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The ARM PMU node is described enough with first compatible so remove the
arm,armv8-pmuv3 to fix dtschema warnings like:
arm-pmu: compatible: Additional items are not allowed ('arm,armv8-pmuv3' was unexpected)
arm-pmu: compatible: ['arm,cortex-a57-pmu', 'arm,armv8-pmuv3'] is too long
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
|
|
Add interrupts property to PWM node on Exynos7 to describe the hardware
fully. No functional change as the interrupts are not used by drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
|
|
Add UFS and UFS-PHY device nods to Exynos7 SoC and Espresso board.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Link: https://lore.kernel.org/r/20200117190305.5257-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The device node name should reflect generic class of a device so rename
the Multi Core Timer node from "mct" to "timer". This will be also in
sync with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Change representation of phandle array as then dt-schema counts number
of its items properly.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
dt-schema supports only order of names "aclk", "pclk". Swap some sysmmu
definitions to make them compatible with schema.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Commit ef72171b3621 ("arm64: dts: exynos: Remove unneeded address space
mapping for soc node") changed the address and size cells in root node from
2 to 1, but /memory nodes for the affected boards were not updated. This
went unnoticed on Exynos5433-based TM2(e) boards, because they use u-boot,
which updates /memory node to the correct values. On the other hand, the
mentioned commit broke boot on Exynos7-based Espresso board, which
bootloader doesn't touch /memory node at all.
This patch reverts commit ef72171b3621 ("arm64: dts: exynos: Remove
unneeded address space mapping for soc node"), so Exynos5433 and Exynos7
SoCs again matches other ARM64 platforms with 64bit mappings in root
node.
Reported-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: ef72171b3621 ("arm64: dts: exynos: Remove unneeded address space mapping for soc node")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> # 5.3.x: 72ddcf6aa224 arm64: dts: exynos: Move GPU under /soc node for Exynos5433
Cc: <stable@vger.kernel.org> # 5.3.x: ede87c3a2bdb arm64: dts: exynos: Move GPU under /soc node for Exynos7
Cc: <stable@vger.kernel.org> # 4.18.x
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Mali GPU hardware module is a standard hardware module integrated to
Exynos7 SoCs, so it should reside under the "/soc" node. The only SoC
components which are placed in the DT root, are those, which are a part
of CPUs: like ARM architected timers and ARM performance measurement
units.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Mali GPU hardware module is a standard hardware module integrated to
Exynos5433 SoCs, so it should reside under the "/soc" node. The only SoC
components which are placed in the DT root, are those, which are a part
of CPUs: like ARM architected timers and ARM performance measurement
units.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add nodes for GPU (Mali T760) to Exynos7. Current support for Exynos7
misses a lot, including proper clocks, power domains, frequency and
voltage scaling and cooling. However this still can provide basic GPU
description. Not tested on HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add nodes for GPU (Mali T760) to Exynos5433. Missing element is the
cooling device. Not tested on HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The XXTI fixed-clock is the input to the SoC therefore it should not be
inside the soc node. This also fixes DTC W=1 warning:
arch/arm64/boot/dts/exynos/exynos7.dtsi:90.17-94.5:
Warning (simple_bus_reg): /soc/xxti: missing or empty reg/ranges property
While moving, change the name of the xxti node to match the generic type
of device (following DeviceTree specification).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The ARM PMU and ARM architected timer nodes are part of ARM CPU design
therefore they should not be inside the soc node. This also fixes DTC
W=1 warnings like:
arch/arm64/boot/dts/exynos/exynos7.dtsi:472.11-480.5:
Warning (simple_bus_reg): /soc/arm-pmu: missing or empty reg/ranges property
arch/arm64/boot/dts/exynos/exynos7.dtsi:482.9-492.5:
Warning (simple_bus_reg): /soc/timer: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add DT node for SlimSSS (aka Slim SecuritySubSystem) in Exynos5433 SoC.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
To support local paths both DECON and GSCALER should enable respective
Smart Deck clocks DSD and GSD on Exynos5433.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
GSCALER should be feed with clock at certain rates. Configure it on
Exynos5433 based TM2 board.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
TM2(e) boards have a Broadcom Bluetooth chip connected to 3rd UART port.
Add a device tree node describing it and its resources (control GPIO lines
and clock).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add node for IMEM clock controller, necessary for Security SubSystem
(SSS) on Exynos5433.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Update DWC3 hardware modules to Exynos5433 specific variant: change
compatible name and add all required clocks (both to the glue node and
DWC3 core node).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
MMC host controller bindings and MMC core defines card detect pin as
active low. Therefore there is no point to invert it twice.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
OF graph describes USB data lanes between USB-PHY and respective MUIC.
Since graph is present and DWC driver can use it to get extcon, obsolete
extcon property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Remove leading 0x from recently introduced unit addresses to fix DTC
warnings:
Warning (unit_address_format): /soc/sysmmu@0x15040000: unit name should not have leading "0x"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Remove no longer needed samsung thermal properties.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
|
|
Add all '1x' clocks to decon and decontv devices. Enabling those clocks
is needed to get proper display on hardware windows no 4 and 5.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
All interrupts from SoC internal modules are level triggered, so fix
incorrect trigger type for I2S1 device on Exynos5433 SoCs.
This fixes following kernel warning:
WARNING: CPU: 2 PID: 1 at drivers/irqchip/irq-gic.c:1016 gic_irq_domain_translate+0xb0/0xb8
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.16.0-rc7-next-20180329 #646
Hardware name: Samsung TM2 board (DT)
pstate: 20000005 (nzCv daif -PAN -UAO)
pc : gic_irq_domain_translate+0xb0/0xb8
lr : irq_create_fwspec_mapping+0x64/0x328
sp : ffff0000098b38d0
...
Call trace:
gic_irq_domain_translate+0xb0/0xb8
irq_create_of_mapping+0x78/0xa0
of_irq_get+0x6c/0xa0
of_irq_to_resource+0x38/0x108
of_irq_to_resource_table+0x50/0x78
of_device_alloc+0x118/0x1b8
of_platform_device_create_pdata+0x54/0xe0
of_platform_bus_create+0x118/0x340
of_platform_bus_create+0x17c/0x340
of_platform_populate+0x74/0xd8
of_platform_default_populate_init+0xb0/0xcc
do_one_initcall+0x50/0x158
kernel_init_freeable+0x184/0x22c
kernel_init+0x10/0x108
ret_from_fork+0x10/0x18
---[ end trace 6decb2b3078d73f0 ]---
Fixes: d8d579c316e8 ("ARM: dts: exynos: Add I2S1 device node to exynos5433")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
There are two Scaler devices in Exynos5433 SoCs. Add nodes for them and
their SYSMMU controllers.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Remove the address space mapping between root and soc nodes to fix
DTC warnings in Exynos5433 and Exynos7 like:
arch/arm64/boot/dts/exynos/exynos5433-tm2.dtb:
Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
The PMU node is the actual block responsible for power management,
including typical Exynos on/off/restart procedures. Therefore the
syscon poweroff and restart nodes logically belong to it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM64 changes for v4.17" from Krzysztof Kozłowski:
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
* tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add OF graph between MHL and USB connector
arm64: dts: exynos: add micro-USB connector node to TM2 platforms
ARM: dts: exynos: Add support for HDMI audio on Exynos 5433 TM2 board
ARM: dts: exynos: Update I2S0 device node in exynos5433
ARM: dts: exynos: Add I2S1 device node to exynos5433
|
|
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace the one occurrence with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
OF graph describes MHL data lanes between MHL and respective USB
connector.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Since USB connector bindings are available we can describe it on TM2(e).
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
This patch updates the sound node of the exynos5433-tm2 board
and adds clock tree configuration in order to support HDMI sound.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The i2s0 node name is changed to a more generic "i2s" and missing
(optional) properties are added. The #sound-dai-cells property is
required for HDMI audio support on TM2 board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add DT node for the second I2S controller available
on Exynos 5433 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Fix typo in unit address of MSCL clock controller (the reg entry is
correct) of Exynso5433.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Convert all hex addresses in node unit addresses to lower case to
fix warnings like:
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dtb: Warning (simple_bus_reg):
Node /soc/video-scaler@13C00000 simple-bus unit address format error, expected "13c00000"
Conversion was done using sed:
$ sed -e 's/@\([a-zA-Z0-9_-]*\) {/@\L\1 {/' -i arch/arm64/boot/dts/exynos/*.dts*
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
sii8620 supports 1 MHz clock, it allows faster transmissions and according
to extensive tests allows to mitigate some obscure bugs in I2C client
logic of the chip.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
This patch adds support for G2D, G3D, CAM0, CAM1, ISP, HVEC power domains
to Exynos5433 SoCs. Currently only clock controllers for those domains are
defined. CAM1 is a parent of CAM0 power domain and CAM0 is a parent of ISP
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
This patch adds support for AUD power domain to Exynos5433 SoCs, which
contains following devices: a clock controller, a pin controller, LPASS
module, I2S controller, ADMA PL330 engine and UART #3 device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|