| Age | Commit message (Collapse) | Author |
|---|
|
The functions in mcpm_entry.c are mostly intended for use during
scary cache and coherency disabling sequences, or do other things
which confuse trace ... like powering a CPU down and not
returning. Similarly for the backend code.
For simplicity, this patch just makes whole files notrace.
There should be more than enough traceable points on the paths to
these functions, but we can be more fine-grained later if there is
a need for it.
Jon Medhurst:
Also added spc.o to the list of files as it contains functions used by
MCPM code which have comments comments like: "might be used in code
paths where normal cacheable locks are not working"
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
SPC(Serial Power Controller) on TC2 also controls the CPU performance
operating points which is essential to provide CPU DVFS. The M3
microcontroller provides two sets of eight performance values, one set
for each cluster (CA15 or CA7). Each of this value contains the
frequency(kHz) and voltage(mV) at that performance level. It expects
these performance level to be passed through the SPC PERF_LVL registers.
This patch adds support to populate these performance levels from M3,
build the mapping to CPU OPPs at the boot and then use it to get and
set the CPU performance level runtime.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Pawel Moll <Pawel.Moll@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This fixes the following build error:
/tmp/cce439dZ.s: Assembler messages:
/tmp/cce439dZ.s:506: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:512: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:513: Error: selected processor does not support ARM mode `dsb '
/tmp/cce439dZ.s:583: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:589: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:590: Error: selected processor does not support ARM mode `dsb '
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This is the MCPM backend for the Virtual Express A15x2 A7x3 CoreTile
aka TC2. This provides cluster management for SMP secondary boot and
CPU hotplug.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[PM: made it drive SCC registers directly and provide base for SPC]
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
Add the required code to properly handle race free platform coherency exit
to the DCSCB power down method.
The power_up_setup callback is used to enable the CCI interface for
the cluster being brought up. This must be done in assembly before
the kernel environment is entered.
Thanks to Achin Gupta and Nicolas Pitre for their help and
contributions.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
|
|
This adds basic CPU and cluster reset controls on RTSM for the
A15x4-A7x4 model configuration using the Dual Cluster System
Configuration Block (DCSCB).
The cache coherency interconnect (CCI) is not handled yet.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
|
|
This patch moves the arch/arm/mach-vexpress/reset.c functionality to
drivers/platform/reset/ and adds the necessary Kconfig wiring.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
|
|
This patch starts using all the configuration infrastructure.
- generic GPIO library is forced now
- sysreg GPIOs are used as MMC CD and WP information sources;
thanks to this MMCI auxiliary data is not longer necessary
- DVI muxer and mode control is removed from non-DT V2P-CA9 code
as this is now handled by the vexpress-dvi driver
- clock generators control is removed as is being handled by the
common clock driver now
- the sysreg and sysctl control is now delegated to the
appropriate drivers and all related code was removed
- NOR Flash set_vpp function has been removed as the control
bit used does _not_ control its VPP line, but the #WP signal
instead (which is de facto unusable in case of Linux MTD
drivers); this also allowed the remove its DT auxiliary
data
The non-DT code defines only minimal required number of
the config devices. Device Trees are updated to make use
of all new features.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
Convert vexpress to multi-platform. This always enables vexpress DT and
makes it the default v7 platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
|
|
Realview and Versatile Express share the same SMP bringup code, so
consolidate the two implementations.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Realview and Versatile Express local timer support is identical, so
consolidate the implementations.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
