| Age | Commit message (Collapse) | Author |
|---|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 32-bit SoC platform updates from Olof Johansson:
"Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (112 commits)
ARM: uniphier: select RESET_CONTROLLER
arm64: uniphier: select RESET_CONTROLLER
ARM: uniphier: remove empty Makefile
ARM: exynos: Clear global variable on init error path
ARM: exynos: Remove outdated maintainer information
ARM: shmobile: Always enable ARCH_TIMER on SoCs with A7 and/or A15
ARM: shmobile: r8a7779: hide unused r8a7779_platform_cpu_kill
soc: r9a06g032: don't build SMP files for non-SMP config
ARM: shmobile: Add the R9A06G032 SMP enabler driver
ARM: at91: pm: configure wakeup sources for ULP1 mode
ARM: at91: pm: add PMC fast startup registers defines
ARM: at91: pm: Add ULP1 mode support
ARM: at91: pm: Use ULP0 naming instead of slow clock
ARM: hisi: handle of_iomap and fix missing of_node_put
ARM: hisi: check of_iomap and fix missing of_node_put
ARM: hisi: fix error handling and missing of_node_put
ARM: mx5: Set the DBGEN bit in ARM_GPC register
ARM: imx51: Configure M4IF to avoid visual artifacts
ARM: imx: call imx6sx_cpuidle_init() conditionally for 6sll
ARM: imx: fix i.MX6SLL build
...
|
|
If we use device tree data for a module interconnect target we want
to map the control registers from the module start. Legacy hwmod platform
data however is using child IP offsets for cpsw module with mpu_rt_idx.
In cases where we have the interconnect target module already using device
tree data with legacy hwmod platform data still around, the sysc register
area is not adjusted for mpu_rt_idx causing wrong registers being accessed.
Let's fix the issue for mixed dts and platform data mode by ioremapping
the module registers using child IP offset if mpu_rt_idx is set. For
device tree only data there's no reason to use mpu_rt_idx.
Fixes: 6c72b3550672 ("ARM: OMAP2+: Parse module IO range from dts for legacy
"ti,hwmods" support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We may call omap_hwmod_parse_module_range() with no hwmod allocated yet
and may have debug enabled. Let's fix this by checking for hwmod before
trying to use it's name.
Fixes: 6c72b3550672 ("ARM: OMAP2+: Parse module IO range from dts for legacy
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Call secure services to enable ACTLR[0] (Enable invalidates of BTB with
ICIALLU) when branch hardening is enabled for kernel.
On GP devices OMAP5/DRA7, there is no possibility to update secure
side since "secure world" is ROM and there are no override mechanisms
possible. On HS devices, appropriate PPA should do the workarounds as
well.
However, the configuration is only done for secondary core, since it is
expected that firmware/bootloader will have enabled the required
configuration for the primary boot core (note: bootloaders typically
will NOT enable secondary processors, since it has no need to do so).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for RTC mode to low level suspend code. This includes
providing the rtc base address for the assembly code to configuring the
PMIC_PWR_EN line late in suspend to enter RTC+DDR mode.
Note: This patch also fold in left out space parameter for
am33xx_emif_sram_table and am43xx_emif_sram_table
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add an argument to the sleep33xx and sleep43xx code to allow us to set
flags to determine which portions of the code get called in order to use
the same code for multiple power saving modes. This patch allows us to
decide whether or not we flush and disable caches, save EMIF context,
put the memory into self refresh and disable the EMIF, and/or invoke
the wkup_m3 when entering into WFI.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Reuse DEFINE_SHOW_ATTRIBUTE() macro instead of open coding file
operations followed by custom ->open() callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When the RTC lock and unlock functions were introduced it was likely
assumed that they would always be called from irq enabled context, hence
the use of local_irq_disable/enable. This is no longer true as the
RTC+DDR path makes a late call during the suspend path after irqs
have been disabled to enable the RTC hwmod which calls both unlock and
lock, leading to IRQs being reenabled through the local_irq_enable call
in omap_hwmod_rtc_lock call.
To avoid this change the local_irq_disable/enable to
local_irq_save/restore to ensure that from whatever context this is
called the proper IRQ configuration is maintained.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- mainly feature additions to drivers (stm32f7, qup, xlp9xx, mlxcpld, ...)
- conversion to use the i2c_8bit_addr_from_msg macro consistently
- move includes to platform_data
- core updates to allow the (still in review) I3C subsystem to connect
- and the regular share of smaller driver updates
* 'i2c/for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (68 commits)
i2c: qup: fix building without CONFIG_ACPI
i2c: tegra: Remove suspend-resume
i2c: imx-lpi2c: Switch to SPDX identifier
i2c: mxs: Switch to SPDX identifier
i2c: busses: make use of i2c_8bit_addr_from_msg
i2c: algos: make use of i2c_8bit_addr_from_msg
i2c: rcar: document R8A77980 bindings
i2c: qup: Add command-line parameter to override SCL frequency
i2c: qup: Correct duty cycle for FM and FM+
i2c: qup: Add support for Fast Mode Plus
i2c: qup: add probe path for Centriq ACPI devices
i2c: robotfuzz-osif: drop pointless test
i2c: robotfuzz-osif: remove pointless local variable
i2c: rk3x: Don't print visible virtual mapping MMIO address
i2c: opal: don't check number of messages in the driver
i2c: ibm_iic: don't check number of messages in the driver
i2c: imx: Switch to SPDX identifier
i2c: mux: pca954x: merge calls to of_match_device and of_device_get_match_data
i2c: mux: demux-pinctrl: use proper parent device for demux adapter
i2c: mux: improve error message for failed symlink
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
|
|
The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a * b, gfp)
as well as handling cases of:
kzalloc(a * b * c, gfp)
with:
kzalloc(array3_size(a, b, c), gfp)
as it's slightly less ugly than:
kzalloc_array(array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
kzalloc(4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
kzalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kzalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
kzalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
- kzalloc
+ kcalloc
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
kzalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
kzalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
kzalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
kzalloc(sizeof(THING) * C2, ...)
|
kzalloc(sizeof(TYPE) * C2, ...)
|
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * E2
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Here are the main updates for SoC support (besides DT additions) for
ARM 32- and 64-bit platforms. The branch also contains defconfig
updates to turn on drivers and options as needed on the various
platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
MAINTAINERS: add NXP linux team maillist as i.MX reviewer
ARM: stm32: Don't select DMA unconditionally on STM32MP157C
arm64: defconfig: Enable PCIe on msm8996 and db820c
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
ARM: berlin: switch to SPDX license identifier
arm: berlin: remove non-necessary flush_cache_all()
ARM: berlin: extend BG2CD Kconfig entry
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
bus: ti-sysc: Fix optional clocks array access
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Late omap soc changes for v4.18 merge window
This series contains two omap1 ams-delta GPIO clean-up patches to get
started with removal of hard-coded GPIO numbers from drivers. And then
the removal of board mach includes from drivers. The second patch mostly
touches the ams-delta audio driver but is included here because of the
removal of the latch gpios and is acked by Mark Brown.
And there are two more am437x related PM patches to save and restore
control module and timer registers for RTC only suspend mode. Looks like
the patch title for the timer changes is a bit misleading, not all the
timer code is yet living under drivers/clocksource. But I had already
pushed out the branch before I noticed this.
* tag 'omap-for-v4.18/soc-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omap variants for v4.18 merge window
This series mostly adds saving of power and clock domain registers for
am335x/am437x suspend to RTC only mode. There is also a non-urgent fix
for omap4 PM where we could end up losing GPIO interrupts if bootloader
has LOGICRETSTATE cleared for domains. And there is a clean-up patch for
omap1 to use device properties for at24 eeprom.
* tag 'omap-for-v4.18/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: Add functions to save and restore powerdomain context
ARM: OMAP2+: clockdomain: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: Add functions to save and restore clockdomain context en-masse.
ARM: omap1: osk: use device properties for at24 eeprom
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add the save and restore for clksrc as part of suspend and resume
so that it saves the counter value and restores. This is needed in
modes like rtc+ddr in self-refresh not doing this stalls the time.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These registers are part of the wkup domain and are lost during RTC only
suspend and also hibernation, so storing/restoring their state is
necessary.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
We may have LOGICRETSTATE cleared by the bootloader or kexec boot.
Currently this means we will see lost GPIO interrupts at least for
network interfaces such as wlcore and smsc911x if PER hits retention.
Let's fix the issue by making sure LOGICRETSTATE is set. Once we have
GPIOs working with wakeirqs then we should be able to clear it.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Inroduce cpu_pm notifiers for context save/restore. This will be
needed for am43xx family in case of rtc only mode with ddr in
self-refresh.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There are two registers on am43x needed for IO daisy chain wake to work
properly, however currently after an RTC+DDR cycle they are lost. We
must take care to save and restore these before and after entering RTC
mode otherwise IO daisy chain wake will stop working from DeepSleep
after resuming.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Inroduce cpu_pm notifiers for context save/restore. This is
needed for am43xx family during rtc only mode with ddr in
self-refresh.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The powerdomain control registers are stored in the WKUP powerdomain on
AM33XX/AM43XX, which is lost on RTC-only suspend and also hibernate. This
adds context save and restore functions for those registers.
Sometimes the powerdomain state does not need to change,
perhaps we only need to change memory retention states, so make
sure the restored state is different from the current state before we wait
for a transition.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Inroduce cpu_pm notifiers for context save/restore. This will be
needed for am43xx family in case of rtc only mode with ddr in
self-refresh.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This is used to support suspend modes like RTC-only and hibernate where
the state of the registers controlling clockdomains is lost.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
ti-sysc driver related changes for omap variants
This series improves the ti-sysc interconnect target module driver to
the point where a most of SoC can be booted with interconnect target
module data configured in device tree instead of legacy platform data.
The related device tree changes need some more work though, and can
wait for v4.19. Also some drivers using nested interconnects like DSS
need more work.
We can now remove the unused pm-noop code that is not doing anything
any longer. And we can now initialize things for PM and display pdata
later to prepare things for using ti-sysc driver.
We also need to add some more quirk handling so we can boot both with
platform data and dts data.
* tag 'omap-for-v4.18/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Show module information for suspend if DEBUG is enabled
bus: ti-sysc: Tag sdio and wdt with legacy mode for suspend
bus: ti-sysc: Detect UARTs for SYSC_QUIRK_LEGACY_IDLE quirk on omap4
bus: ti-sysc: Detect omap4 type timers for quirk
bus: ti-sysc: Add initial support for external resets
bus: ti-sysc: Improve suspend and resume handling
bus: ti-sysc: Tag some modules resource providers for noirq suspend
bus: ti-sysc: Add handling for clkctrl opt clocks
bus: ti-sysc: Make child clock alias handling more generic
bus: ti-sysc: Handle simple-bus for nested children
ARM: OMAP2+: Make display related init into device_initcall
ARM: OMAP2+: Initialize SoC PM later
ARM: OMAP2+: Only probe SDMA via ti-sysc if configured in dts
ARM: OMAP2+: Use signed value for sysc register offsets
ARM: OMAP2+: Allow using ti-sysc for system timers
ARM: OMAP2+: Drop unused pm-noop
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
smp_processor_id() checks preemption if CONFIG_DEBUG_PREEMPT is enabled,
causing a warning dump during boot:
[ 5.042377] BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
[ 5.050281] caller is pwrdm_set_next_pwrst+0x48/0x88
[ 5.055330] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.14.24-g57341df0b4 #1
Use the raw_smp_processor_id() for the trace instead, this value does
not need to be perfectly correct. The alternative of disabling preempt
is too heavy weight operation to be applied in PM hot path for just
tracing purposes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can initialize almost everything at normal module_init time with
ti-sysc except for clocks and timers. To prepare for that, let's make
display init into device_initcall as otherwise we'll be calling
of_platform_populate() before the parent has probed.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to probe devices until at module_init time and we
currently have at least PM trying to use I2C for PMICs early on.
As only a part of the SoC init_early is SoC specific, we only need to call
the SoC specific PM init function. And we can modify omap2_common_pm_late_init()
so it becomes a late_initcall().
Note that this changes am335x to call omap2_clk_enable_autoidle_all() that
seems to be missing currently.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We still have some SDMA probing using omap_device_build() for the
arch/arm/plat-omap/dma.c part that the dmaengine driver then uses.
So we still need to ensure that omap_device_build() works even if we
probe and manage the dmaengine driver via ti-sysc. And we don't want
to call dev_pm_domain_set() as otherwise we'd also have omap_device
try to manage the hardware in addition to ti-sysc.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We currently don't know if a revision register exists or not. Zero is
often a valid offset for the revision register. As we are still checking
device tree data against platform data, we will get bogus warnings with
correct device tree data because of incomplete platform data.
Let's fix the issue by using signed offsets and tag the revision registers
that don't exist with -ENODEV, and init the missing ones with the correct
revision register offset.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If a system timer is configured with an interrconnect target module in
the dts, the ti,hwmods and module fck are at the interconnect target
level. Then there's a separate fck for the timer child device.
If the child device has a separate functional clock, we need to configure
it directly. For example, timer clk clkctrl clock bit 0 is the module
clock for the interconnect target, and bit 24 being the functional clock
for the timer IP.
For system timers, we already mark them as disabled. Now must also mark
the interconnect target module as disabled to prevent ti-sysc to manage
it instead of the system timer.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The sleep33xx and sleep43xx files should not depend on a header file
generated in drivers/memory. Remove this dependency and instead allow
both drivers/memory and arch/arm/mach-omap2 to generate all macros
needed in headers local to their own paths.
This fixes an issue where the build fail will when using O= to set a
split object directory and arch/arm/mach-omap2 is built before
drivers/memory with the following error:
.../drivers/memory/emif-asm-offsets.c:1:0: fatal error: can't open
drivers/memory/emif-asm-offsets.s for writing: No such file or directory
compilation terminated.
Fixes: 41d9d44d7258 ("ARM: OMAP2+: pm33xx-core: Add platform code needed for PM")
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like these functions don't do anything in the mainline kernel so
we can just drop it.
Note that we must now also remove ir-rx51 pdata as it relies on the dummy
platform data that does not do anything. And ir-rx51 is calling a pdata
callback that doesn't do anything without checking if it exists first.
For configuring device specific minimal latencies, the interface to use
is pm_qos_add_request(). For an example, see what was done in commit
9834ffd1ecc3 ("ASoC: omap-mcbsp: Add PM QoS support for McBSP to prevent
glitches"). I've added some comments to ir-rx51 so people using it can
add pm_qos support and test it.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When CONFIG_CACHE_L2X0 is disabled, the am43xx specific suspend
implemnentation fails to link:
arch/arm/mach-omap2/sleep43xx.o: In function `get_l2cache_base':
(.text+0x180): undefined reference to `omap4_get_l2cache_base'
This adds an #ifdef protection around the code, like we do for am44xx.
Fixes: 41d37e61372f ("ARM: OMAP2+: Introduce low-level suspend code for AM43XX")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Two omap5 specific aux control module patches for v4.17" from Tony Lindgren:
On omap5 there is an aux control module that we are not handling
currently for clocks, so let's add support for it.
* tag 'omap-for-v4.17/soc-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP5: control: add support for control module wkup pad config
ARM: omap2+: control: add support for auxiliary control module instances
|
|
Match the new compatible string in the control module driver. The base
infra maps the required syscon ranges and clock registers if available.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Control module can have multiple instances in a system, each with separate
address space and features. Add base support for these auxiliary instances,
with support for syscon and clock mappings under them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Driver changes for ti-sysc for v4.17" from Tony Lindgren:
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
* tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable ti-sysc to use device tree data for smartreflex
PM / AVS: SmartReflex: Prepare to use device tree based probing
ARM: OMAP2+: Try to parse earlycon from parent too
ARM: OMAP2+: Add checks for device tree based sysconfig data
ARM: OMAP2+: Add functions to allocate module data from device tree
bus: ti-sysc: Handle some devices in omap_device compatible way
bus: ti-sysc: Add support for platform data callbacks
bus: ti-sysc: Remove unnecessary debugging statements
bus: ti-sysc: Improve handling for no-reset-on-init and no-idle-on-init
bus: ti-sysc: Handle stdout-path for debug console
bus: ti-sysc: Add suspend and resume handling
bus: ti-sysc: Add fck clock alias for children with notifier_block
ARM: OMAP2+: Prepare to pass auxdata for smartreflex
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Add am335x and am437x PM code for v4.17" from Tony Lindgren:
This series of changes from Dave Gerlach adds the PM related
code to allow low-power suspend states. The code consists of
the SoC specific assembly code and a related PM driver.
* tag 'omap-for-v4.17/am-pm-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: Add pm33xx driver for basic suspend support
ARM: OMAP2+: pm33xx-core: Add platform code needed for PM
ARM: OMAP2+: Introduce low-level suspend code for AM43XX
ARM: OMAP2+: Introduce low-level suspend code for AM33XX
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Move omap timer to drivers for 4.17" from Tony Lindgren:
This series from Keerthy and Ladislav Michl move omap dmtimer code
to drivers. As we don't want to export custom timer functions to
random drivers, we also need to update the related PWM driver to
pass the timer specific functions in platform data.
Note that this series is based on a merge of omap1 specific timer
fix and omap2+ platform data clean-up to keep things working and
make the move a bit simpler.
* tag 'omap-for-v4.17/timer-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
clocksource: timer-ti-dm: Check prescaler value
clocksource: timer-ti-dm: Consolidate set source
clocksource: timer-ti-dm: Make unexported functions static
ARM: OMAP: pdata-quirks: Remove unused timer pdata
pwm: pwm-omap-dmtimer: Adapt driver to utilize dmtimer pdata ops
clocksource: timer-ti-dm: Hook device platform data if not already assigned
clocksource: timer-ti-dm: Populate the timer ops to the pdata
clocksource: timer-ti-dm: Add timer ops to the platform data structure
ARM: OMAP: Move dmtimer driver out of plat-omap to drivers under clocksource
clocksource: timer-ti-dm: Replace architecture
ARM: OMAP: Move dmtimer.h out of plat-omap
ARM: OMAP: timer: Wrap the inline functions under OMAP2PLUS define
ARM: OMAP: dmtimer: Remove all the exports
ARM: OMAP: Fix dmtimer init for omap1
|
|
Let's enable ti-sysc probing of child devices. So far we have only used
ti-sysc to probe interconnect target modules to idle them for cases where
the SoC does not have any child devices configured for the module, such
as smartreflex on dra7.
As we have smartreflex driver configured in the device tree for some SoCs,
we need to flip things on with a single patch to prevent both omap_device
and ti-sysc to probe smartreflex. So let's stop probing smartreflex with
omap_device and probe it with ti-sysc by enabling passing the auxdata.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With ti-sysc driver the "ti,hwmods" property will be moved to the
interconnect target module instead of the child device. To keep
earlycon working, we need to match against the interconnect target
module in the ti-sysc case.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can check the device tree based sysconfig data against the existing
platform data to make sure we're not introducing regressions. Then at
some point after the sysconfig data comes from device tree, we can just
drop the related platform data.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can have ti-sysc driver manage the interconnect target module via
platform data callback functions to hwmod code. This allows initializing
and idling the devices using dts data instead of the legacy static data
for interconnect target modules.
Let's add functions to configure the module sysconfig data with platform
callbacks from ti-sysc driver.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This is in bank1, not in bank3.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can use just v7_invalidate_l1 here instead of v7_flush_dcache_all
like the comments say.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Most of the PM code needed for am335x and am437x can be moved into a
module under drivers but some core code must remain in mach-omap2 at the
moment. This includes some internal clockdomain APIs and low-level ARM
APIs which are also not exported for use by modules.
Implement a few functions that handle these low-level platform
operations can be passed to the pm33xx module through the use of
platform data.
In addition to this, to be able to share data structures between C and
the sleep33xx and sleep43xx assembly code, we can automatically generate
all of the C struct member offsets and sizes as macros by processing
pm-asm-offsets.c into assembly code and then extracting the relevant
data as is done for the generated platform asm-offsets.h files.
Finally, add amx3_common_pm_init to create a dummy platform_device for
pm33xx so that our soon to be introduced pm33xx module can probe on
am335x and am437x platforms to enable basic suspend to mem and standby
support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Although similar to AM33XX, introduce a new low-level asm file for
suspend containing new context save and restore paths for EMIF and l2
cache disabling and enabling.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
