| Age | Commit message (Collapse) | Author |
|---|
|
'misc_devel_3.6' into omap_devel_f_3.6
|
|
The DMADISABLE bit is a semi-automatic bit present in sysconfig register
of some modules. When the DMA must perform read/write accesses, the
DMADISABLE bit is cleared by the hardware. But when the DMA must stop for power
management, software must set the DMADISABLE bit back to 1.
In cases where the ROMCODE/BOOTLOADER uses dma, the hardware clears the
DMADISABLE bit (but the romcode/bootloader might not set it back to 1).
In order for the kernel to start in a clean state, it is
necessary for the kernel to set DMADISABLE bit back to 1 (irrespective
of whether it's been set to 1 in romcode or bootloader).
During _reset of the (hwmod)device, the DMADISABLE bit is set so that it
does not prevent idling of the system. (NOTE: having DMADISABLE to 0,
prevents the system to idle)
DMADISABLE bit is present in usbotgss module of omap5.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: updated to apply; fixed checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
In case of AM33xx family of devices (like cpsw) have different sysc
bit field offsets defined,
sysc_type3:
| 3 2 | 1 0 |
| STDBYMODE | IDLEMODE |
So introduce new sysc_type3 in omap_hwmod common data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
bootloader
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
To reduce kernel source file data duplication, share struct
omap_hwmod_dma_info arrays across OMAP2xxx and 3xxx hwmod data files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add a new hwmod class for IVA devices. To be used when hwmods
are created for IVA2 on OMAP3.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add support for categorizing and iterating over hardware IP blocks by
the "class" of the IP block. The class is the type of the IP block:
e.g., "timer", "timer1ms", etc. Move the OCP_SYSCONFIG/SYSSTATUS data
from the struct omap_hwmod into the struct omap_hwmod_class, since
it's expected to stay consistent for each class. While here, fix some
comments.
The hwmod_class structures in this patch were designed and proposed by
Benoît Cousson <b-cousson@ti.com> and were refined in a discussion
between Thara Gopinath <thara@ti.com>, Kevin Hilman
<khilman@deeprootsystems.com>, and myself.
This patch uses WARN() lines that are longer than 80 characters, as
Kevin noted a broader lkml consensus to increase greppability by
keeping the messages all on one line.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
register bits.
In OMAP3 Some modules like Smartreflex do not have the regular sysconfig
register.Instead clockactivity bits are part of another register at a
different bit position than the usual bit positions 8 and 9.
In OMAP4, a new scheme is available due to the new protocol
between the PRCM and the IPs. Depending of the scheme, the SYSCONFIG
bitfields position will be different.
The IP_REVISION register should be at offset 0x00.
It should contain a SCHEME field. From this we can determine whether
the IP follows legacy scheme or the new scheme.
31:30 SCHEME Used to distinguish between old scheme and current.
Read 0x0: Legacy protocol.
Read 0x1: New PRCM protocol defined for new OMAP4 IPs
For legacy IP
13:12 MIDLEMODE
11:8 CLOCKACTIVITY
6 EMUSOFT
5 EMUFREE
4:3 SIDLEMODE
2 ENAWAKEUP
1 SOFTRESET
0 AUTOIDLE
For new OMAP4 IP's, the bit position in SYSCONFIG is (for simple target):
5:4 STANDBYMODE (Ex MIDLEMODE)
3:2 IDLEMODE (Ex SIDLEMODE)
1 FREEEMU (Ex EMUFREE)
0 SOFTRESET
Unfortunately In OMAP4 also some IPs will not follow any of these
two schemes. This is the case at least for McASP, SmartReflex
and some security IPs.
This patch introduces a new field sysc_fields in omap_hwmod_sysconfig which
can be used by the hwmod structures to specify the offsets for the
sysconfig register of the IP.Also two static structures
omap_hwmod_sysc_type1 and omap_hwmod_sysc_type2 are defined
which can be used directly to populate the sysc_fields if the IP follows
legacy or new OMAP4 scheme. If the IP follows none of these two schemes
a new omap_hwmod_sysc_fields structure has to be defined and
passed as part of omap_hwmod_sysconfig.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
