summaryrefslogtreecommitdiff
path: root/arch/arm/mach-omap2/Kconfig
AgeCommit message (Collapse)Author
2010-10-08omap3: Add minimal OMAP3 IGEP module supportEnric Balletbo i Serra
The OMAP3 IGEP module is a low-power, high performance production-ready system-on-module (SOM) based on TI's OMAP3 family. More about this board at www.igep.es. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> [tony@atomide.com: updated for the mmc changes and to be selected by default] Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-09-29OMAP: SERIAL: Enable omap-serial driver in KconfigGovindraj.R
Enable omap-serial driver in /mach-omap2/Kconfig and move 8250 driver selection for zoom boards. With omap-serial driver addition all omap-uarts can be handled with omap-serial driver. With addition of omap-serial driver console parameter needs be changed in bootargs from ttyS* should be replaced with ttyO* [O --> OMAP not ZERO] For example: ttyS0[UART1 on 3430SDP] changes to ttyO0. But with some boards that do not use omap-uart as console uart. we need to handle them with 8250 driver. Ex: ZOOM2/3. For zoom2/3 board we need to use 8250 serial driver and console parameter will remain ttyS0 which basically uses a Quad uart placed on the debug board connected through a gpio line. Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-09-28ARM: OMAP3LOGIC: Adding LogicPD OMAP3 board supportTim Nordell
Adding support for LogicPD's OMAP 3530 LV SOM and OMAP 35x Torpedo board. Signed-off-by: Tim Nordell <tim.nordell@logicpd.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-09-27omap3: Introduce CompuLab CM-T3517 moduleIgor Grinberg
Add basic suppot, enable uart and led. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-09-20omap: Update and rename common defconfig for omap2plus devicesSantosh Shilimkar
This patch addresses below things - Renaming existing omap3_defconfig which has OMAP2, OMAP3 and OMAP4 builds enabled to more appropriate name 'omap2plus_defconfig' - L1 cache shift is suppose to be 5 on OMAP4 where as it is 6 on previous OMAPs. Keeping it to 5 is safer option for OMAP4 and previous OMAPs. For OMAP3 only build the shift would be still 6 - Enable needed Errata's for OMAP4 to work with DMA based device drivers CONFIG_PL310_ERRATA_588369=y CONFIG_ARM_ERRATA_720789=y - Enable the Micrel ethernet controller CONFIG_KS8851=y CONFIG_KS8851_MLL=y With above three changes, OMAP4 ethernet, mmc etc works reliably. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap4: Add OMAP4 Panda SupportDavid Anders
Add initial support for the OMAP4 based Panda Board. Signed-off-by: David Anders <x0132446@ti.com> [tony@atomide.com: selected board by default in Kconfig] Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap2/3/4: Add Kconfig option to compile in typical omap featuresTony Lindgren
This produces a sane config that's suitable for using as the base for most omap2/3/4 boards. Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap2/3/4: Select all omaps and boards by defaultTony Lindgren
Select all omaps and boards by default Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap2/3/4: Move Kconfig options to mach-omap2/KconfigTony Lindgren
Move omap2/3/4 specific Kconfig options to mach-omap2/Kconfig Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap: Make omap specific features appear under Kconfig menuTony Lindgren
This will make Kconfig look nicer for selecting omap processor type Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap: mux: Select POP package for 2430SDPTony Lindgren
Select POP package for 2430SDP Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap: mux: Select POP package for N8X0Tony Lindgren
Select POP package for N8X0 Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap: mux: Select POP package for ApollonTony Lindgren
Select POP package for Apollon Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap: mux: Select SIP package for H4Tony Lindgren
Select SIP package for H4 Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05omap: mux: Add data for 2420Tony Lindgren
Add data for 2420. Big thanks to Paul Walmsley <paul@pwsan.com> for generating usable mux data out of TRMs. Cc: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-05-20omap3: Add support for OMAP3Stalker boardsJason
Add support for OMAP3Stalker boards Signed-off-by: Jason Lam <lzg@ema-tech.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-05-20omap2: select ARCH_OMAP_OTG for OMAP2430 SDPViral Mehta
Configuration for OMAP2430 should select ARCH_OMAP_OTG just like it is done for OMAP2420 Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-04-23omap: Devkit8000: Add missing package selectionThomas Weber
Devkit8000 uses the CUS package for OMAP3530. This patch adds missing package selection for CUS and enables CONFIG_MUX. Replace whitespace with tab in Kconfig. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-19Add minimal support for DevKit8000Thomas Weber
These patches add board support for the Timll DevKit8000. The DevKit8000 is a beagle board clone from Timll, sold by armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and JTAG interface. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-17omap3: Fix typo on IGEP v2 boardEnric Balletbo i Serra
Fix typo on IGEP v2 board Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-15omap2/3/4: Replace orred CONFIG_ARCH_OMAP2/3/4 with CONFIG_ARCH_OMAP2PLUSTony Lindgren
omap: Replace orred CONFIG_ARCH_OMAP2/3/4 with CONFIG_ARCH_OMAP2PLUS Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-15omap3: Replace ARCH_OMAP34XX with ARCH_OMAP3Tony Lindgren
Replace ARCH_OMAP34XX with ARCH_OMAP3 Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-15omap2: Convert ARCH_OMAP24XX to ARCH_OMAP2Tony Lindgren
Convert ARCH_OMAP24XX to ARCH_OMAP2 Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08omap3: EVM: Choose OMAP_PACKAGE_CBBVaibhav Hiremath
Without this the kernel doesn't boot, it craches in omap_mux_package_fixup(), since the package_subset becomes NULL. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-15omap3: Allow EHCI to be built on OMAP3Olof Johansson
OMAP34XX has EHCI, so select USB_ARCH_HAS_EHCI. Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11omap3: cm-t35: add mux initializationMike Rapoport
CM-T35 can be assembled with different set of peripherals thus making certain interfaces available to user as GPIOs or dedicated pins. Because of it CM-T35 bootloader sets up mux configuration only for pins necessary to boot the system and the rest of the mux configuration is done by the kernel. Besides, having mux configuration in the kernel allows to minimize dependancy on bootloader. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11omap3: Board file of Always Innovating OMAP3-based Touch BookGregoire Gentil
Board file of Always Innovating OMAP3-based Touch Book Signed-off-by: Gregoire Gentil <gregoire@gentil.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11omap: mux: Add 36xx CBP package supportTony Lindgren
Add 36xx CBP package support Cc: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11omap: mux: Add new style init functions to omap3 board-*.c filesTony Lindgren
Add new style mux init functions to omap3 board-*.c files So far Beagle has been confirmed to be a CBB package, and CM-T35 a CUS package. Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11omap: mux: Add new style pin multiplexing data for 34xxTony Lindgren
Add new style mux data for 34xx. This should also work with 3630 easily by adding the processor subset and ball data. Note that this data is __initdata, and gets optimized out except for the GPIO pins if CONFIG_OMAP_MUX is not set. Also note that this data uses omap3630 naming for the SDMMC registers instead of 34xx naming with just MMC. Cc: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11OMAP3: SDRC: Place SDRC AC timing and MR changes in CORE DVFS SRAM code ↵Paul Walmsley
behind Kconfig The code that reprograms the SDRC memory controller during CORE DVFS, mach-omap2/sram34xx.S:omap3_sram_configure_core_dpll(), does not ensure that all L3 initiators are prevented from accessing the SDRAM before modifying the SDRC AC timing and MR registers. This can cause memory to be corrupted or cause the SDRC to enter an unpredictable state. This patch places that code behind a Kconfig option, CONFIG_OMAP3_SDRC_AC_TIMING for now, and adds a note explaining what is going on. Ideally the code can be added back in once supporting code is present to ensure that other initiators aren't touching the SDRAM. At the very least, these registers should be reprogrammable during kernel init to deal with buggy bootloaders. Users who know that all other system initiators will not be touching the SDRAM can also re-enable this Kconfig option. This is a modification of a patch originally written by Rajendra Nayak <rnayak@ti.com> (the original is at http://patchwork.kernel.org/patch/51927/). Rather than removing the code completely, this patch just comments it out. Thanks to Benoît Cousson <b-cousson@ti.com> and Christophe Sucur <c-sucur@ti.com> for explaining the technical basis for this and for explaining what can be done to make this path work in future code. Thanks to Richard Woodruff <r-woodruff2@ti.com>, Nishanth Menon <nm@ti.com>, and Olof Johansson <olof@lixom.net> for their comments. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Rajendra Nayak <rnayak@ti.com> Cc: Christophe Sucur <c-sucur@ti.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Richard Woodruff <r-woodruff2@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Olof Johansson <olof@lixom.net>
2009-12-08Merge branch 'omap-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (149 commits) arm: omap: Add omap3_defconfig AM35xx: Defconfig for AM3517 EVM board AM35xx: Add support for AM3517 EVM board omap: 3630sdp: defconfig creation omap: 3630sdp: introduce 3630 sdp board support omap3: Add defconfig for IGEP v2 board omap3: Add minimal IGEP v2 support omap3: Add CompuLab CM-T35 defconfig omap3: Add CompuLab CM-T35 board support omap3: rx51: Add wl1251 wlan driver support omap3: rx51: Add SDRAM init omap1: Add default kernel configuration for Herald omap1: Add board support and LCD for HTC Herald omap: zoom2: update defconfig for LL_DEBUG_NONE omap: zoom3: defconfig creation omap3: zoom: Introduce zoom3 board support omap3: zoom: Drop i2c-1 speed to 2400 omap3: zoom: rename zoom2 name to generic zoom omap3: zoom: split board file for software reuse omap3evm: MIgrate to smsc911x ethernet driver ... Fix trivial conflict (two unrelated config options added next to each other) in arch/arm/mach-omap2/Makefile
2009-12-02ARM: 5843/1: OMAP3: add AMBA devices for ETM and ETBAlexander Shishkin
This enables on-chip tracing components found in omap3xxx. Signed-off-by: Alexander Shishkin <virtuoso@slind.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-11-25AM35xx: Add support for AM3517 EVM boardRanjith Lohithakshan
This patch creates a minimal AM3517 EVM board support. Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-25omap: 3630sdp: introduce 3630 sdp board supportvikram pandita
Add 3630SDP board support The board shares the same peripherals as a zoom2 main. So reuse the peripheral file of zoom platform. Peripheral zoom2 zoom3 sdp3630 --------------------------------------- Ethernet smsc smsc smc NOR n/a n/a B Onenand n/a n/a B HDMI A A B (persent on different i2c) NAND A A A (same nand) SDRAM A A A (same sdram) Keypad A A A (same twl) Camera A A A (same sensor can be mounted) LCD Display A A A (same wvga display) OPPs A A A (same chip feature) Audio A A A (same audio via twl5030) OMAP3630 details can be found here: http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606 Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-25omap3: Add minimal IGEP v2 supportEnric Balletbo i Serra
The IGEP v2 board is a low-cost, fan-less and industrial temperature range single board computer that unleashes laptop-like performance and expandability without the bulk, expense, or noise of typical desktop machines. Its architecture shares much in common with other OMAP3 boards. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-25omap3: Add CompuLab CM-T35 board supportMike Rapoport
This patch adds basic support for CompuLab CM-T35 module. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-22omap3: zoom: Introduce zoom3 board supportvikram pandita
Zoom3 is the next version of Zoom2 board. There has been a silicon update from zoom2 to zoom3. Zoom2 has OMAP34xx Zoom3 has OMAP3630 [1] Zoom3 = OMAP3630 SOM board [2] + same zoom2 main board [3] + same debugboard Zoom3 has a SDRAM part from Hynix Zoom2 had SDRAM part from micron Hynix memory timings are contributed by: Chalhoub, Nicole and Bour, Vincent Reuse the zoom2 files as much for zoom3, as at board level, there is no change at all. References: (courtesy Nishant Menon) [1] OMAP3630 http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606 [2] SOM boards http://logicpd.com/products/system-modules/texas-instruments-omap35x-som-lv [3] Zoom2 boards http://logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp OMAP3630: Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Cc: Nicole Chalhoub <n-chalhoub@ti.com> Cc: Vincent Bour <v-bour@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-22omap2: Fix detection of n8x0Tony Lindgren
Otherwise the machine_is_nokia_n8*() does not work. Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-08-28OMAP2: add board file for Nokia N800 and N810Kalle Valo
Add board file for Nokia N800 and N810 devices. Currently only serial ports, onenand and spi are configured, more to come later. Tested on Nokia N800. Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-08-28OMAP2: compile usb-tusb6010.cKalle Valo
For some reason usb-tusb6010.c was't compiled, add it to Makefile and Kconfig. This is prepraration for upcoming n8x0 support. Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-05-28ARM: OMAP4: Add support for 4430 SDPSantosh Shilimkar
This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP board file supports only minimal set of drivers. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-05-28ARM: OMAP3: Add omap3 EVM supportSyed Mohammed Khasim
Add omap3 EVM support Signed-off-by: Syed Mohammed Khasim <khasim@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-05-28ARM: OMAP3: Add support for OMAP3 Zoom2 boardVikram Pandita
This patch creates the minimal OMAP3 Zoom2 board support. Signed-off-by: Mikkel Christensen <mlc@ti.com> Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-23ARM OMAP3: Initial support for Nokia RX-51, v3Lauri Leukkunen
Adds board files and related headers for Nokia RX-51 Internet Tablet. This patch has been updated with some clean-up patches posted earlier to linux-omap list. Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-23ARM: OMAP3: Add support for 3430 SDP, v4Syed Mohammed Khasim
Add support for 3430 SDP. Various updates have been merged into this patch from the linux-omap list. Patch updated to initialize regulators by David Brownell <dbrownell@users.sourceforge.net>. Signed-off-by: Syed Mohammed Khasim <khasim@ti.com> David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-12-10ARM: OMAP3: Add basic support for Pandora handheld consoleGrazvydas Ignotas
This patch adds support for basic features: uarts, i2c, and rtc. Also includes defconfig. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-10-10ARM: OMAP3: Add basic board support for OMAP LDPNishant Kamat
This adds minimal board support for the OMAP3430 LDP development platform. Signed-off-by: Nishant Kamat <nskamat@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-10-09ARM: OMAP3: Add support for the Gumstix Overo board (rev 3)Steve Sakoman
This patch adds minimal overo support. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-10-09ARM: OMAP3: Add minimal Beagle board supportSyed Mohammed, Khasim
Add minimal Beagle board support. Based on earlier patches by Syed Mohammed Khasim with some fixes from linux-omap tree. Signed-off-by: Syed Mohammed Khasim <khasim@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-15 03:27:37 +0000