| Age | Commit message (Collapse) | Author |
|---|
|
The recently merged AT91SAM9 watchdog driver uses the
AT91SAM9X_WATCHDOG config variable, whereas the original version of
the driver (and the platform support code) used AT91SAM9_WATCHDOG.
This causes the watchdog platform_device to never be registered, and
therefore the driver not to be initialized.
This patch:
- updates the platform support code to use AT91SAM9X_WATCHDOG.
- includes <linux/io.h> to fix compile error (same fix as was applied
to at91rm9200_wdt.c)
- fixes comment regarding watchdog clock-rates in at91rm9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In at91_add_device_nand(), do not configure the Static Memory
controller with specific timing values.
The *_devices.c files are board independent, and the SMC timing values
are specific to the NAND devices that are installed on the board.
The board-specific files are now responsible for configuring the
Static Memory controller (if the don't want to leave it up to a
bootloader).
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Structs called at91_nand_data where renamed to atmel_nand_data
and configs called *MTD_NAND_AT91* where renamed to
*MTD_NAND_ATMEL*. This was unfortunately not done consistently,
causing NAND chips not being initialised on several ARM boards.
I am aware that the author of the original change did not rename
MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example.
All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order
to keep naming consistency.
This patch was only tested on a MACH_SAM9_L9260, as this is the
only ARM board I have to my disposal.
Before this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
105
$ git-ls-files |xargs grep at91_nand |wc -l
4
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
8
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
47
After this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
109
$ git-ls-files |xargs grep at91_nand |wc -l
0
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
55
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
0
Signed-off-by: Pieter du Preez <pdupreez@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf).
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.
This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.
It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.
Therefore, we should only initialize the framebuffer if we allocated it
ourselves. This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e. the user didn't provide a fixed
address or the reservation failed.
I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All the SAM9 boards supported by mainline and the AT91 patches have
been converted to the new-style UART initialization. Therefore drop
support for the old at91_init_serial() interface for SAM9.
at91_uarts[] array can also be marked as __initdata.
The warning that no serial-console is defined moved from
at91_set_serial_console() to at91_add_device_serial() since the whole
point is the board-specific file is not calling
at91_set_serial_console().
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Register platform_devices for the Timer/Counter Block peripherals
found on the AT91RM9200, SAM9 & CAP9 processors.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The RTT-as-RTC driver will search for the user-specified RTT
peripheral via ID number (0 .. 1).
Therefore if the processor only contains a single RTT peripheral, we
need to set its platform_device.id to "0" instead of "-1".
Also add the missing platform_device resource for the CAP9 processor.
Bug reported by Sedji Gaouaou.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The AT91CAP9 processor includes the same Static Memory Controller
(SMC) peripheral as the SAM9 processors, but replaces the SDRAM
Controller with a DDR/SDR Controller (DDRSDRC).
This patch splits the existing
include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and
at91sam9_smc.h.
It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Currently the udc pullup is enabled by default on boot. If the device
is connected to a host at this time, the host starts the negotiation
before the udc/gadget driver is ready to handle it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the LED initialization code out of the various *_devices.c files,
and into leds.c.
Also add support for NEW_LEDs.
Patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.
The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.
As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Map the complete memory region (SZ_256M) as is done on the other AT91
processors.
The SMC_SMARTMEDIA bit should be set in the EBI controller to enable
the hardware NAND logic.
(Patch from Sascha Erlacher)
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Core support of the Atmel SSC library for all Atmel AT91 processors.
Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Replace hard-coded DMA mask (0xffffffff) with DMA_BIT_MASK(32) as
defined in dma-mapping.h.
Set "dma_mask" field for the UART platform_devices.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add platform_device and initialization for the RTT (Real Time Timer)
and WDT (Watchdog) integrated in the Atmel AT91SAM9 processors.
For SAM9263, register both RTT peripherals.
[From: David Brownell <dbrownell@users.sourceforge.net>]
Provide platform_resources for RTT peripherals
[From: David Brownell <dbrownell@users.sourceforge.net>]
Add support for RTC peripheral on AT91SAM9RL (same RTC peripherals as
AT91RM9200)
[From: David Brownell <dbrownell@users.sourceforge.net>]
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for STN LCD displays on Atmel AT91SAM9261-based boards.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The AT91 I2C driver is currently marked as "broken" due to hardware
issues. This patch enables AT91-based platforms to also use the
bitbanged GPIO for I2C.
This updates platform setup logic (setting up an i2c-gpio device
using the same pins as the i2c-at91 device, unless only the BROKEN
driver is enabled).
Also make use of the new-style initialization of I2C devices using
i2c_register_board_info().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
- Include atmel_lcdc.h in at91sam926{1,3}_devices.c
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Define SZ_512, SZ_256 and SZ_16 in asm-arm/sizes.h.
Remove the definitions from the at91*_devices.c files.
(Dependent on ARM patch #4370/2)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The GPIO pin setup should be handed by the platform-setup code, and not
directly by the driver.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.
These changes are:
* The system peripheral I/O region we remap has increased from
0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
* The increased I/O region forces changes to entry-macro.S and
debug-macro.S due to ARM's limited immediate offset addressing
modes.
* Maximum number of GPIO banks increases to 5.
* 2 MMC controllers so the board-setup code needs to specify which
controller it wishes to use when calling at91_add_device_mmc().
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
