| Age | Commit message (Collapse) | Author |
|---|
|
Get rid of the kzm9d_defconfig. The KZM9D is now supported
as DT only in case of EMEV2 is selected in the kernel
configuration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
DEVTMPFS is needed for udev
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
From Simon Horman:
Renesas ARM based SoC board updates for v3.14
* Global
- Kconfig: Mention Renesas ARM SoCs instead of SH-Mobile
* r7s72100 SoC (RZ/A1H) based Genmai Board
- Add Multiplatform support
- Add Reference DT
* r8a7791 (R-Car M2) based Koelsch board
- Add pinctrl_register_mappings() for Koelsch
- Hook up SW30-SW36 on Koelsch
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Add Multiplatform support
- Set .debounce_interval for GPIO keys
- Add SW2 to GPIO keys
- Add Led 6, 7 and 8 support
- Add reference DT
- Enable PFC/GPIO
* r8a7790 (R-Car H2) based Lager board
- Add gpio/fixed regulator for SDHI
- Add SPI FLASH support on QSPI
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Set .debounce_interval for GPIO keys
* r8a7778 (R-Car M1) based Bock-W board
- bockw: remove unused RSND_SSI_CLK_FROM_ADG
- Set .debounce_interval for GPIO keys
- Correct FPGA ioremap area
- Use regulator for MMCIF
* r8a7740 (R-Mobile A1) based Armadillo board
- Correct FSI address size
* sh7374 (SH-Mobile AP4) based Mackerel board
- Use pinconf API to configure pin pull-down
- clk_round_rate() can return a zero to indicate an error
* tag 'renesas-boards-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (75 commits)
ARM: shmobile: lager: add gpio/fixed regulator for SDHI
ARM: shmobile: bockw: remove unused RSND_SSI_CLK_FROM_ADG
ARM: shmobile: armadillo: fixup FSI address size
ARM: Kconfig: Mention Renesas ARM SoCs instead of SH-Mobile
ARM: shmobile: mackerel: Use pinconf API to configure pin pull-down
ARM: shmobile: Lager:add SPI FLASH support on QSPI
ARM: shmobile: mackerel: clk_round_rate() can return a zero to indicate an error
ARM: shmobile: Add pinctrl_register_mappings() for Koelsch
ARM: shmobile: Use ->init_late() on Lager
ARM: shmobile: Hook up SW30-SW36 on Koelsch
ARM: shmobile: koelsch: mark GPIO keys as wake-up sources
ARM: shmobile: Use ->init_late() on Koelsch
ARM: shmobile: lager: mark GPIO keys as wake-up sources
ARM: shmobile: r7s72100 Genmai Multiplatform
ARM: shmobile: r7s72100 Genmai DT reference C bits
ARM: shmobile: r7s72100 Genmai DT reference DTS bits
ARM: shmobile: Initial r8a7791 and Koelsch multiplatform support
ARM: shmobile: koelsch: set .debounce_interval
ARM: shmobile: lager: set .debounce_interval
ARM: shmobile: bockw: add pin pull-up setting for SDHI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
SH-Mobile platforms are transitioning from non-multiplatform to
multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has
been created to group all multiplatform-enabled SH-Mobile SoCs. The
existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't
been converted yet.
This arrangement works fine for the arch/ code, but lots of drivers
needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on
ARCH_SHMOBILE only. In order to avoid changing them, rename
ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean
ARCH_SHMOBILE configuration symbol that is selected by both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This is required to allow the load address to be supplied
as an environment variable when building a uImage.
LOADADDR=0x40008000 ARCH=arm make uImage
This is necessary since "ARM: shmobile: Remove legacy KZM9D board code"
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
* Do not disable SUSPEND
Suspend seems to work fine on the kzm9d.
This is part of an effort reduce differences between mach-shmobile
defconfigs with a view to using a common defconfig.
* Enable PM_RUNTIME
This also seems to work fine on the kzm9d.
This is part of an effort reduce differences between mach-shmobile
defconfigs with a view to using a common defconfig.
* Move kernel command line from defconfig to dts.
This brings us one small step closer to sharing defconfig
between kzm9d and other boards.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables PMU(Performance Monitoring Unit) for emev2.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Original work by Magnus Damm, tested and tweaked by Simon Horman
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
