| Age | Commit message (Collapse) | Author |
|---|
|
The use of the GPIOF_* flags is deprecated, so don't advertise them
here. Document the plain numbers for now until we have a better
solution.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
R8A7778 is R-Car (not R-Mobile) M1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The w1 master driver includes a complete open drain emulation
reimplementation among other things.
This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.
When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.
As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.
w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.
The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.
To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.
We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The AXP813 has only two GPIOs. GPIO0 can either be used as a GPIO, an
LDO regulator or an ADC. GPIO1 can be used either as a GPIO or an LDO
regulator.
Moreover, the status bit of the GPIOs when in input mode is not offset
by 4 unlike the AXP209.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The X-Powers AXP209 has 3 GPIOs. GPIO0/1 can each act either as a GPIO,
an ADC or a LDO regulator. GPIO2 can only act as a GPIO.
This adds the pinctrl features to the driver so GPIO0/1 can be used as
ADC or LDO regulator.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes from Ingo Molnar:
- topology enumeration fixes
- KASAN fix
- two entry fixes (not yet the big series related to KASLR)
- remove obsolete code
- instruction decoder fix
- better /dev/mem sanity checks, hopefully working better this time
- pkeys fixes
- two ACPI fixes
- 5-level paging related fixes
- UMIP fixes that should make application visible faults more debuggable
- boot fix for weird virtualization environment
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
x86/pkeys/selftests: Fix protection keys write() warning
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
x86/mpx/selftests: Fix up weird arrays
x86/pkeys: Update documentation about availability
x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
x86/smpboot: Fix __max_logical_packages estimate
x86/topology: Avoid wasting 128k for package id array
perf/x86/intel/uncore: Cache logical pkg id in uncore driver
x86/acpi: Reduce code duplication in mp_override_legacy_irq()
x86/acpi: Handle SCI interrupts above legacy space gracefully
x86/boot: Fix boot failure when SMP MP-table is based at 0
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/selftests: Add test for mapping placement for 5-level paging
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: a documentation fix, a Sparse warning fix and a debugging
fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Fix task state recording/printout
sched/deadline: Don't use dubious signed bitfields
sched/deadline: Fix the description of runtime accounting in the documentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- use 'pwd' instead of '/bin/pwd' for portability
- clean up Makefiles
- fix ld-option for clang
- fix malloc'ed data size in Kconfig
- fix parallel building along with coccicheck
- fix a minor issue of package building
- prompt to use "rpm-pkg" instead of "rpm"
- clean up *.i and *.lst patterns by "make clean"
* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: drop $(extra-y) from real-objs-y
kbuild: clean up *.i and *.lst patterns by make clean
kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
kbuild: pkg: use --transform option to prefix paths in tar
coccinelle: fix parallel build with CHECK=scripts/coccicheck
kconfig/symbol.c: use correct pointer type argument for sizeof
kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
kbuild: remove all dummy assignments to obj-
kbuild: create built-in.o automatically if parent directory wants it
kbuild: /bin/pwd -> pwd
|
|
Pull KVM updates from Radim Krčmář:
"Trimmed second batch of KVM changes for Linux 4.15:
- GICv4 Support for KVM/ARM
- re-introduce support for CPUs without virtual NMI (cc stable) and
allow testing of KVM without virtual NMI on available CPUs
- fix long-standing performance issues with assigned devices on AMD
(cc stable)"
* tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
kvm: vmx: Allow disabling virtual NMI support
kvm: vmx: Reinstate support for CPUs without virtual NMI
KVM: SVM: obey guest PAT
KVM: arm/arm64: Don't queue VLPIs on INV/INVALL
KVM: arm/arm64: Fix GICv4 ITS initialization issues
KVM: arm/arm64: GICv4: Theory of operations
KVM: arm/arm64: GICv4: Enable VLPI support
KVM: arm/arm64: GICv4: Prevent userspace from changing doorbell affinity
KVM: arm/arm64: GICv4: Prevent a VM using GICv4 from being saved
KVM: arm/arm64: GICv4: Enable virtual cpuif if VLPIs can be delivered
KVM: arm/arm64: GICv4: Hook vPE scheduling into vgic flush/sync
KVM: arm/arm64: GICv4: Use the doorbell interrupt as an unblocking source
KVM: arm/arm64: GICv4: Add doorbell interrupt handling
KVM: arm/arm64: GICv4: Use pending_last as a scheduling hint
KVM: arm/arm64: GICv4: Handle INVALL applied to a vPE
KVM: arm/arm64: GICv4: Propagate property updates to VLPIs
KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE
KVM: arm/arm64: GICv4: Handle CLEAR applied to a VLPI
KVM: arm/arm64: GICv4: Propagate affinity changes to the physical ITS
KVM: arm/arm64: GICv4: Unmap VLPI when freeing an LPI
...
|
|
Pull more drm updates from Dave Airlie:
"Fixes/cleanups for rc1, non-desktop flags for VR
- remove the MSM dt-bindings file Rob managed to push in the previous
pull.
- add a property/edid quirk to denote HMD devices, I had these
hanging around for a few weeks and Keith had done some work on
them, they are fairly self contained and small, and only affect
people using HTC Vive VR headsets so far.
- amdgpu, tegra, tilcdc, fsl fixes
- some imx-drm cleanups I missed, these seemed pretty small, and no
reason to hold off.
I have one TTM regression fix (fixes bochs-vga in qemu) sitting
locally awaiting review I'll probably send that in a separate pull
request tomorrow"
* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
dt-bindings: remove file that was added accidentally
drm/edid: quirk HTC vive headset as non-desktop. [v2]
drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
drm: add connector info/property for non-desktop displays [v2]
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
drm/tegra: sor: Reimplement pad clock
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/amd/pp: fix dpm randomly failed on Vega10
drm/amdgpu: set f_mapping on exported DMA-bufs
drm/amdgpu: Properly allocate VM invalidate eng v2
drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
drm/fsl-dcu: avoid disabling pixel clock twice on suspend
...
|
|
Pull documentation updates from Jonathan Corbet:
"A few late-arriving docs updates that have no real reason to wait.
There's a new "Co-Developed-by" tag described by Greg, and a build
enhancement from Willy to generate docs warnings during a kernel build
(but only when additional warnings have been requested in general)"
* tag 'docs-4.15-2' of git://git.lwn.net/linux:
Add optional check for bad kernel-doc comments
Documentation: fix profile= options in kernel-parameters.txt
documentation/svga.txt: update outdated file
kokr/memory-barriers.txt: Fix typo in paring example
kokr/memory-barriers/txt: Replace uses of "transitive"
Documentation/process: add Co-Developed-by: tag for patches with multiple authors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into next-keys
Merge keys subsystem changes from David Howells, for v4.15.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as
well as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp"
* tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32-lp: Remove pwm_is_enabled() check before calling pwm_disable()
pwm: mediatek: Add MT2712/MT7622 support
pwm: sunxi: Use of_device_get_match_data()
pwm: atmel-tcb: Support backup mode
dt-bindings: pwm: Add R-Car D3 device tree bindings
pwm: img: Add runtime PM
pwm: img: Add suspend / resume handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is nothing scary this cycle, mostly driver fixes and updates.
The core fix has been in for a while and has been tested on multiple
kernel revisions by multiple teams.
Core:
- Fix setting the alarm to the next expiring timer
New drivers:
- Mediatek MT7622 RTC
- NXP PCF85363
- Spreadtrum SC27xx PMIC RTC
Drivers updates:
- Use generic nvmem to expose the Non volatile ram for ds1305,
ds1511, m48t86 and omap
- abx80x: solve possible race condition at probe
- armada38x: support trimming the RTC oscillator
- at91rm9200: fix reading the alarm value at boot
- ds1511: allow waking platform
- m41t80: rework square wave output
- pcf8523: support trimming the RTC oscillator
- pcf8563: fix clock output rate
- pl031: make interrupt optional
- xgene: fix suspend/resume"
* tag 'rtc-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
dt-bindings: rtc: imxdi: Improve the bindings text
rtc: sc27xx: Add Spreadtrum SC27xx PMIC RTC driver
dt-bindings: rtc: Add Spreadtrum SC27xx RTC documentation
rtc: at91rm9200: fix reading alarm value
rtc: at91rm9200: stop calculating yday in at91_rtc_readalarm
rtc: sysfs: Use time64_t variables to set time/alarm
rtc: xgene: mark PM functions as __maybe_unused
rtc: xgene: Fix suspend/resume
rtc: pcf8563: don't alway enable the alarm
rtc: pcf8563: fix output clock rate
rtc: rx8010: Fix for incorrect return value
rtc: rx8010: Specify correct address for RX8010_RESV31
rtc: rx8010: Remove duplicate define
rtc: m41t80: remove unneeded checks from m41t80_sqw_set_rate
rtc: m41t80: avoid i2c read in m41t80_sqw_is_prepared
rtc: m41t80: avoid i2c read in m41t80_sqw_recalc_rate
rtc: m41t80: fix m41t80_sqw_round_rate return value
rtc: m41t80: m41t80_sqw_set_rate should return 0 on success
rtc: add support for NXP PCF85363 real-time clock
rtc: omap: Support scratch registers
...
|
|
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
|
|
git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: various cleanups
- Switch to drm_*_get/put() helpers
- Use correct parallel-display connector enum: DPI instead of VGA
- Remove incorrect unit name from device tree binding documentation example
- Remove an unused variable
* tag 'imx-drm-next-2017-10-18' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: ipu-dc: Remove unused 'di' variable
dt-bindings: fsl-imx-drm: Remove incorrect "@di0" usage
drm/imx: parallel-display: use correct connector enum
drm/imx: switch to drm_*_get(), drm_*_put() helpers
|
|
All users of init_timer() have been updated. Remove the ancient interface.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Now that CPUs that implement Memory Protection Keys are publicly
available we can be a bit less oblique about where it is available.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171111001228.DC748A10@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here (though removal of the dead igafb
driver stands out in diffstat).
Summary:
- convert timers to use timer_setup() (Kees Cook, Thierry Reding)
- fix panels support on iMX boards in mxsfb driver (Stefan Agner)
- fix timeout on EDID read in udlfb driver (Ladislav Michl)
- add missing modes to fix out of bounds access in controlfb driver
(Geert Uytterhoeven)
- update initialisation paths in sa1100fb driver to be more robust
(Russell King)
- fix error handling path of ->probe method in au1200fb driver
(Christophe JAILLET)
- fix handling of cases when either panel or crt is defined in
sm501fb driver (Sudip Mukherjee, Colin Ian King)
- add ability to the Goldfish FB driver to be recognized by OS via DT
(Aleksandar Markovic)
- structures constifications (Bhumika Goyal)
- misc fixes (Allen Pais, Gustavo A. R. Silva, Dan Carpenter)
- misc cleanups (Colin Ian King, Himanshu Jha, Markus Elfring)
- remove dead igafb driver"
* tag 'fbdev-v4.15' of git://github.com/bzolnier/linux: (42 commits)
OMAPFB: prevent buffer underflow in omapfb_parse_vram_param()
video: fbdev: sm501fb: fix potential null pointer dereference on fbi
fbcon: Initialize ops->info early
video: fbdev: Convert timers to use timer_setup()
video: fbdev: pxa3xx_gcu: Convert timers to use timer_setup()
fbdev: controlfb: Add missing modes to fix out of bounds access
video: fbdev: sis_main: mark expected switch fall-throughs
video: fbdev: cirrusfb: mark expected switch fall-throughs
video: fbdev: aty: radeon_pm: mark expected switch fall-throughs
video: fbdev: sm501fb: mark expected switch fall-through in sm501fb_blank_crt
video: fbdev: intelfb: remove redundant variables
video/fbdev/dnfb: Use common error handling code in dnfb_probe()
sm501fb: suspend and resume fb if it exists
sm501fb: unregister framebuffer only if registered
sm501fb: deallocate colormap only if allocated
video: goldfishfb: Add support for device tree bindings
Documentation: Add device tree binding for Goldfish FB driver
video: udlfb: Fix read EDID timeout
video: fbdev: remove dead igafb driver
video: fbdev: mxsfb: fix pixelclock polarity
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Remove mc13892 as a trivial device
- Improve of_find_node_by_name() documentation
- Fix unit test dtc warnings
- Clean-ups of USB binding documentation
- Fix potential NULL deref in of_pci_map_rid
* tag 'devicetree-fixes-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: trivial-devices: Remove fsl,mc13892
of: Document exactly what of_find_node_by_name() puts
of: unittest: disable interrupts_property warning
of: unittest: let dtc generate __local_fixups__
dt-bindings: usb: document hub and host-controller properties
dt-bindings: usb: clean up compatible property
dt-bindings: usb: fix reg-property port-number range
dt-bindings: usb: fix example hub node name
of/pci: Fix theoretical NULL dereference
|
|
Improve the bindings text by doing the following changes:
- Remove the i.MX53 reference, as the RTC on i.MX53 is a different hardware
- Add 'clocks' to the list of required properties
- Explain that the optional security violation irq is the second entry
- Use the real unit address and irq numbers for i.MX25
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Juergen Borleis <jbe@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This device's bindings are not trivial: Additional properties are
documented in in Documentation/devicetree/bindings/mfd/mc13xxx.txt.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Correctly the formatting of several additions to the profile= option
that have been added by using <profiletype> and listing the choices
for it.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Drop CONFIG_VIDEO_400_HACK info completely.
Drop CONFIG_VIDEO_RETAIN and CONFIG_VIDEO_LOCAL completely.
Drop CONFIG_VIDEO_COMPACT and CONFIG_VIDEO_VESA info completely.
Drop CONFIG_VIDEO_SVGA info since it has been removed.
Drop chapter number & section number references since they are wrong.
Drop (bad) ftp URL for 800x600 Thinkpad XF86Config.
Rename CONFIG_VIDEO_GFX_HACK to VIDEO_GFX_HACK since it is not a
Kconfig symbol. And to match the source code.
Build options are controlled by the kernel kconfig utility.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-By: Martin Mares <mj@ucw.cz>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This commit applies an upstream change, commit d92f842bb30f
("memory-barriers.txt: Fix typo in pairing example") to the Korean
translation.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This commit applies two upstream change, commit f1ab25a30ce8
("memory-barriers: Replace uses of "transitive"") and commit 0902b1f44a72
("memory-barriers: Rework multicopy-atomicity section") to the Korean
translation. Those two changes are applied with this signle commit
because the second change is improvement of the first one.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
authors
Sometimes a single patch is the result of multiple authors. As git only
can have one "author" of a patch, it is still good to properly give
credit to the other developers of a commit. To address this, document
the "Co-Developed-by:" tag which can be used to show other authors of
the patch.
Note, these other authors must also provide a Signed-off-by: tag as it
is their work that is being submitted here.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Pull ntb updates from Jon Mason:
"Support for the switchtec ntb and related changes. Also, a couple of
bug fixes"
[ The timing isn't great. I had asked people to send me pull requests
before my family vacation, and this code has not even been in
linux-next as far as I can tell. But Logan Gunthorpe pleaded for its
inclusion because the Switchtec driver has apparently been around for
a while, just never in linux-next - Linus ]
* tag 'ntb-4.15' of git://github.com/jonmason/ntb:
ntb: intel: remove b2b memory window workaround for Skylake NTB
NTB: make idt_89hpes_cfg const
NTB: switchtec_ntb: Update switchtec documentation with notes for NTB
NTB: switchtec_ntb: Add memory window support
NTB: switchtec_ntb: Implement scratchpad registers
NTB: switchtec_ntb: Implement doorbell registers
NTB: switchtec_ntb: Add link management
NTB: switchtec_ntb: Add skeleton NTB driver
NTB: switchtec_ntb: Initialize hardware for doorbells and messages
NTB: switchtec_ntb: Initialize hardware for memory windows
NTB: switchtec_ntb: Introduce initial NTB driver
NTB: Add check and comment for link up to mw_count() and mw_get_align()
NTB: Ensure ntb_mw_get_align() is only called when the link is up
NTB: switchtec: Add link event notifier callback
NTB: switchtec: Add NTB hardware register definitions
NTB: switchtec: Export class symbol for use in upper layer driver
NTB: switchtec: Move structure definitions into a common header
ntb: update maintainer list for Intel NTB driver
|
|
The switchtec_ntb driver has a couple requirements on the switchec's
hardware configuration so we add these notes to the documentation.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
"Here is the collected material against Platform Drivers x86 subsystem.
It's rather bit busy cycle for PDx86, mostly due to Dell SMBIOS driver
activity
For this cycle we have quite an update for the Dell SMBIOS driver
including WMI work to provide an interface for SMBIOS tokens via sysfs
and WMI support for 2017+ Dell laptop models. SMM dispatcher code is
split into a separate driver followed by a new WMI dispatcher. The
latter provides a character device interface to user space.
The git history also contains a merge of immutable branch from Wolfram
Sang in order to apply a dependent fix to the Intel CherryTrail
Battery Management driver.
Other Intel drivers got a lot of cleanups. The Turbo Boost Max 3.0
support is added for Intel Skylake.
Peaq WMI hotkeys driver gets its own maintainer and white list of
supported models.
Silead DMI is expanded to support few additional platforms.
Tablet mode via GMMS ACPI method is added to support some ThinkPad
tablets.
new driver:
- Add driver to force WMI Thunderbolt controller power status
asus-wmi:
- Add lightbar led support
dell-laptop:
- Allocate buffer before rfkill use
dell-smbios:
- fix string overflow
- Add filtering support
- Introduce dispatcher for SMM calls
- Add a sysfs interface for SMBIOS tokens
- only run if proper oem string is detected
- Prefix class/select with cmd_
- Add pr_fmt definition to driver
dell-smbios-smm:
- test for WSMT
dell-smbios-wmi:
- release mutex lock on WMI call failure
- introduce userspace interface
- Add new WMI dispatcher driver
dell-smo8800:
- remove redundant assignments to byte_data
dell-wmi:
- don't check length returned
- clean up wmi descriptor check
- increase severity of some failures
- Do not match on descriptor GUID modalias
- Label driver as handling notifications
dell-*wmi*:
- Relay failed initial probe to dependent drivers
dell-wmi-descriptor:
- check if memory was allocated
- split WMI descriptor into it's own driver
fujitsu-laptop:
- Fix radio LED detection
- Don't oops when FUJ02E3 is not presnt
hp_accel:
- Add quirk for HP ProBook 440 G4
hp-wmi:
- Fix tablet mode detection for convertibles
ideapad-laptop:
- Add Lenovo Yoga 920-13IKB to no_hw_rfkill dmi list
intel_cht_int33fe:
- Update fusb302 type string, add properties
- make a couple of local functions static
- Work around BIOS bug on some devices
intel-hid:
- Power button suspend on Dell Latitude 7275
intel_ips:
- Convert timers to use timer_setup()
- Remove FSF address from GPL notice
- Remove unneeded fields and label
- Keep pointer to struct device
- Use PCI_VDEVICE() macro
- Switch to new PCI IRQ allocation API
- Simplify error handling via devres API
intel_pmc_ipc:
- Revert Use MFD framework to create dependent devices
- Use MFD framework to create dependent devices
- Use spin_lock to protect GCR updates
- Use devm_* calls in driver probe function
intel_punit_ipc:
- Fix resource ioremap warning
intel_telemetry:
- Remove useless default in Kconfig
- Add needed inclusion
- cleanup redundant headers
- Fix typos
- Fix load failure info
intel_telemetry_debugfs:
- Use standard ARRAY_SIZE() macro
intel_turbo_max_3:
- Add Skylake platform
intel-wmi-thunderbolt:
- Silence error cases
mlx-platform:
- make a couple of structures static
peaq_wmi:
- Fix missing terminating entry for peaq_dmi_table
peaq-wmi:
- Remove unnecessary checks from peaq_wmi_exit
- Add DMI check before binding to the WMI interface
- Revert Blacklist Lenovo ideapad 700-15ISK
- Blacklist Lenovo ideapad 700-15ISK
silead_dmi:
- Add silead, home-button property to some tablets
- Add entry for the Digma e200 tablet
- Fix GP-electronic T701 entry
- Add entry for the Chuwi Hi8 Pro tablet
sony-laptop:
- Drop variable assignment in sony_nc_setup_rfkill()
- Fix error handling in sony_nc_setup_rfkill()
thinkpad_acpi:
- Implement tablet mode using GMMS method
tools/wmi:
- add a sample for dell smbios communication over WMI
wmi:
- release mutex on module acquistion failure
- create userspace interface for drivers
- Don't allow drivers to get each other's GUIDs
- Add new method wmidev_evaluate_method
- Destroy on cleanup rather than unregister
- Cleanup exit routine in reverse order of init
- Sort include list"
* tag 'platform-drivers-x86-v4.15-1' of git://git.infradead.org/linux-platform-drivers-x86: (74 commits)
platform/x86: silead_dmi: Add silead, home-button property to some tablets
platform/x86: dell-laptop: Allocate buffer before rfkill use
platform/x86: dell-*wmi*: Relay failed initial probe to dependent drivers
platform/x86: dell-wmi-descriptor: check if memory was allocated
platform/x86: Revert intel_pmc_ipc: Use MFD framework to create dependent devices
platform/x86: dell-smbios-wmi: release mutex lock on WMI call failure
platform/x86: wmi: release mutex on module acquistion failure
platform/x86: dell-smbios: fix string overflow
platform/x86: intel_pmc_ipc: Use MFD framework to create dependent devices
platform/x86: intel_punit_ipc: Fix resource ioremap warning
platform/x86: dell-smo8800: remove redundant assignments to byte_data
platform/x86: hp-wmi: Fix tablet mode detection for convertibles
platform/x86: intel_ips: Convert timers to use timer_setup()
platform/x86: sony-laptop: Drop variable assignment in sony_nc_setup_rfkill()
platform/x86: sony-laptop: Fix error handling in sony_nc_setup_rfkill()
tools/wmi: add a sample for dell smbios communication over WMI
platform/x86: dell-smbios-wmi: introduce userspace interface
platform/x86: wmi: create userspace interface for drivers
platform/x86: dell-smbios: Add filtering support
platform/x86: dell-smbios-smm: test for WSMT
...
|
|
Pull remoteproc updates from Bjorn Andersson:
"This adds an interface for configuring Qualcomm's "secure SMMU" and
adds support for booting the modem Hexagon on MSM8996.
Two new debugfs entries are added in the remoteproc core to introspect
the list of memory carveouts and the loaded resource table"
* tag 'rproc-v4.15' of git://github.com/andersson/remoteproc:
remoteproc: qcom: Fix error handling paths in order to avoid memory leaks
remoteproc: qcom: Drop pr_err in q6v5_xfer_mem_ownership()
remoteproc: debug: add carveouts list dump feature
remoteproc: debug: add resource table dump feature
remoteproc: qcom: Add support for mss remoteproc on msm8996
remoteproc: qcom: Make secure world call for mem ownership switch
remoteproc: qcom: refactor mss fw image loading sequence
firmware: scm: Add new SCM call API for switching memory ownership
|
|
Pull rpmsg updates from Bjorn Andersson:
- turn RPMSG_VIRTIO into a user selectable config
- fix few bugs in GLINK
- provide the support for specifying initial buffer sizes for GLINK
channels.
* tag 'rpmsg-v4.15' of git://github.com/andersson/remoteproc:
rpmsg: glink: The mbox client knows_txdone
rpmsg: glink: Add missing MODULE_LICENSE
rpmsg: glink: Use best fit intent during tx
rpmsg: glink: Add support to preallocate intents
dt-bindings: soc: qcom: Support GLINK intents
rpmsg: glink: Initialize the "intent_req_comp" completion variable
rpmsg: Allow RPMSG_VIRTIO to be enabled via menuconfig or defconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
|
|
Most places use pwd and rely on $PATH lookup. Moving the remaining
absolute path /bin/pwd users over for consistency.
Also, a reason for doing /bin/pwd -> pwd instead of the other way around
is because I believe build systems should make little assumptions on
host filesystem layout. Case in point, we do this kind of patching
already in NixOS.
Ref. commit 028568d84da3cfca49f5f846eeeef01441d70451
("kbuild: revert $(realpath ...) to $(shell cd ... && /bin/pwd)").
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild misc updates from Masahiro Yamada:
- Clean up and fix RPM package build
- Fix a warning in DEB package build
- Improve coccicheck script
- Improve some semantic patches
* tag 'kbuild-misc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
docs: dev-tools: coccinelle: delete out of date wiki reference
coccinelle: orplus: reorganize to improve performance
coccinelle: use exists to improve efficiency
builddeb: Pass the kernel:debarch substvar to dpkg-genchanges
Coccinelle: use false positive annotation
coccinelle: fix verbose message about .cocci file being run
coccinelle: grep Options and Requires fields more precisely
Coccinelle: make DEBUG_FILE option more useful
coccinelle: api: detect identical chip data arrays
coccinelle: Improve setup_timer.cocci matching
Coccinelle: setup_timer: improve messages from setup_timer
kbuild: rpm-pkg: do not force -jN in submake
kbuild: rpm-pkg: keep spec file until make mrproper
kbuild: rpm-pkg: fix jobserver unavailable warning
kbuild: rpm-pkg: replace $RPM_BUILD_ROOT with %{buildroot}
kbuild: rpm-pkg: fix build error when CONFIG_MODULES is disabled
kbuild: rpm-pkg: refactor mkspec with here doc
kbuild: rpm-pkg: clean up mkspec
kbuild: rpm-pkg: install vmlinux.bz2 unconditionally
kbuild: rpm-pkg: remove ppc64 specific image handling
|
|
Merge more updates from Andrew Morton:
- a bit more MM
- procfs updates
- dynamic-debug fixes
- lib/ updates
- checkpatch
- epoll
- nilfs2
- signals
- rapidio
- PID management cleanup and optimization
- kcov updates
- sysvipc updates
- quite a few misc things all over the place
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
EXPERT Kconfig menu: fix broken EXPERT menu
include/asm-generic/topology.h: remove unused parent_node() macro
arch/tile/include/asm/topology.h: remove unused parent_node() macro
arch/sparc/include/asm/topology_64.h: remove unused parent_node() macro
arch/sh/include/asm/topology.h: remove unused parent_node() macro
arch/ia64/include/asm/topology.h: remove unused parent_node() macro
drivers/pcmcia/sa1111_badge4.c: avoid unused function warning
mm: add infrastructure for get_user_pages_fast() benchmarking
sysvipc: make get_maxid O(1) again
sysvipc: properly name ipc_addid() limit parameter
sysvipc: duplicate lock comments wrt ipc_addid()
sysvipc: unteach ids->next_id for !CHECKPOINT_RESTORE
initramfs: use time64_t timestamps
drivers/watchdog: make use of devm_register_reboot_notifier()
kernel/reboot.c: add devm_register_reboot_notifier()
kcov: update documentation
Makefile: support flag -fsanitizer-coverage=trace-cmp
kcov: support comparison operands collection
kcov: remove pointless current != NULL check
kernel/panic.c: add TAINT_AUX
...
|
|
The updated documentation describes new KCOV mode for collecting
comparison operands.
Link: http://lkml.kernel.org/r/20171011095459.70721-3-glider@google.com
Signed-off-by: Victor Chibotaru <tchibo@google.com>
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Popov <alex.popov@linux.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: <syzkaller@googlegroups.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Link: http://lkml.kernel.org/r/CAKW4uUyCi=PnKf3epgFVz8z=1tMtHSOHNm+fdNxrNw3-THvRCA@mail.gmail.com
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix minor typo.
Fix missing words in explaining parsing of last line number.
Link: http://lkml.kernel.org/r/ebb7ff42-4945-103f-d5b4-f07a6f3343a7@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I like _ONCE warnings because it's guaranteed that they don't flood the
log.
During testing I find it useful to reset the state of the once warnings,
so that I can rerun tests and see if they trigger again, or can
guarantee that a test run always hits the same warnings.
This patch adds a debugfs interface to reset all the _ONCE warnings so
that they appear again:
echo 1 > /sys/kernel/debug/clear_warn_once
This is implemented by putting all the warning booleans into a special
section, and clearing it.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20171017221455.6740-1-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Right now there is no convenient way to check if a process is being
coredumped at the moment.
It might be necessary to recognize such state to prevent killing the
process and getting a broken coredump. Writing a large core might take
significant time, and the process is unresponsive during it, so it might
be killed by timeout, if another process is monitoring and
killing/restarting hanging tasks.
We're getting a significant number of corrupted coredump files on
machines in our fleet, just because processes are being killed by
timeout in the middle of the core writing process.
We do have a process health check, and some agent is responsible for
restarting processes which are not responding for health check requests.
Writing a large coredump to the disk can easily exceed the reasonable
timeout (especially on an overloaded machine).
This flag will allow the agent to distinguish processes which are being
coredumped, extend the timeout for them, and let them produce a full
coredump file.
To provide an ability to detect if a process is in the state of being
coredumped, we can expose a boolean CoreDumping flag in
/proc/pid/status.
Example:
$ cat core.sh
#!/bin/sh
echo "|/usr/bin/sleep 10" > /proc/sys/kernel/core_pattern
sleep 1000 &
PID=$!
cat /proc/$PID/status | grep CoreDumping
kill -ABRT $PID
sleep 1
cat /proc/$PID/status | grep CoreDumping
$ ./core.sh
CoreDumping: 0
CoreDumping: 1
[guro@fb.com: document CoreDumping flag in /proc/<pid>/status]
Link: http://lkml.kernel.org/r/20170928135357.GA8470@castle.DHCP.thefacebook.com
Link: http://lkml.kernel.org/r/20170920230634.31572-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull two power management fixes from Rafael Wysocki:
"This is the change making /proc/cpuinfo on x86 report current CPU
frequency in "cpu MHz" again in all cases and an additional one
dealing with an overzealous check in one of the helper routines in the
runtime PM framework"
* tag 'pm-fixes-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Drop children check from __pm_runtime_set_status()
x86 / CPU: Always show current CPU frequency in /proc/cpuinfo
|
|
Pull amdgpu DC display code for Vega from Dave Airlie:
"This is the pull request for the AMD DC (display code) layer which is
a requirement to program the display engines on the new Vega and Raven
based GPUs. It also contains support for all amdgpu supported GPUs
(CIK, VI, Polaris), which has to be enabled. It is also a kms atomic
modesetting compatible driver (unlike the current in-tree display
code).
I've kept it separate from drm-next because it may have some things
that cause you to reject it.
Background story:
AMD have an internal team creating a shared OS codebase for display at
hw bring up time using information from their hardware teams. This
process doesn't lead to the most Linux friendly/looking code but we
have worked together on cleaning a lot of it up and dealing with
sparse/smatch/checkpatch, and having their team internally adhere to
Linux coding standards.
This tree is a complete history rebased since they started opening it,
we decided not to squash it down as the history may have some value.
Some of the commits therefore might not reach kernel standards, and we
are steadily training people in AMD to better write commit msgs.
There is a major bunch of generated bandwidth calculation and
verification code that comes from their hardware team. On Vega and
before this is float calculations, on Raven (DCN10) this is double
based. They do the required things to do FP in the kernel, and I could
understand this might raise some issues. Rewriting the bandwidth would
be a major undertaken in reverification, it's non-trivial to work out
if a display can handle the complete set of mode information thrown at
it.
Future story:
There is a TODO list with this, and it address most of the remaining
things that would be nice to refine/remove. The DCN10 code is still
under development internally and they push out a lot of patches quite
regularly and are supporting this code base with their display team. I
think we've reached the point where keeping it out of tree is going to
motivate distributions to start carrying the code, so I'd prefer we
get it in tree. I think this code is slightly better than STAGING
quality but not massively so, I'd really like to see that float/double
magic gone and fixed point used, but AMD don't seem to think the
accuracy and revalidation of the code is worth the effort"
* tag 'drm-for-v4.15-amd-dc' of git://people.freedesktop.org/~airlied/linux: (1110 commits)
drm/amd/display: fix MST link training fail division by 0
drm/amd/display: Fix formatting for null pointer dereference fix
drm/amd/display: Remove dangling planes on dc commit state
drm/amd/display: add flip_immediate to commit update for stream
drm/amd/display: Miss register MST encoder cbs
drm/amd/display: Fix warnings on S3 resume
drm/amd/display: use num_timing_generator instead of pipe_count
drm/amd/display: use configurable FBC option in dm
drm/amd/display: fix AZ clock not enabled before program AZ endpoint
amdgpu/dm: Don't use DRM_ERROR in amdgpu_dm_atomic_check
amd/display: Fix potential null dereference in dce_calcs.c
amdgpu/dm: Remove unused forward declaration
drm/amdgpu: Remove unused dc_stream from amdgpu_crtc
amdgpu/dc: Fix double unlock in amdgpu_dm_commit_planes
amdgpu/dc: Fix missing null checks in amdgpu_dm.c
amdgpu/dc: Fix potential null dereferences in amdgpu_dm.c
amdgpu/dc: fix more indentation warnings
amdgpu/dc: handle allocation failures in dc_commit_planes_to_stream.
amdgpu/dc: fix indentation warning from smatch.
amdgpu/dc: fix non-ansi function decls.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- introduce brcmstb AVS TMON thermal driver (Brian Norris)
- add Rockchip RV1108 support in rockchip thermal driver (Rocky Hao)
- major rework on HISI driver plus additional support of hisi3660
(Daniel Lezcano)
- add nvmem-cells binding on imx6sx (Leonard Crestez)
- fix a NULL pointer dereference on ti thermal driver unloading (Tony
Lindgren)
- improve tmon tool to make it easier to cross-compile tmon (Markus
Mayer)
- add Coffee Lake and Cannon Lake support for intel processor and pch
thermal drivers (Srinivas Pandruvada)
- other small fixes and cleanups (Arvind Yadav, Colin Ian King, Allen
Wild, Nicolin Chen, Baruch SiachNiklas Söderlund, Arnd Bergmann)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (44 commits)
thermal: pch: Add Cannon Lake support
thermal: int340x: processor_thermal: Add Coffee Lake support
thermal: int340x: processor_thermal: Add Cannon Lake support
thermal: bxt: remove redundant variable trip
thermal: cpu_cooling: pr_err() strings should end with newlines
thermal: add brcmstb AVS TMON driver
Documentation: devicetree: add binding for Broadcom STB AVS TMON
thermal/drivers/hisi: Add support for hi3660 SoC
thermal/drivers/hisi: Prepare to add support for other hisi platforms
thermal/drivers/hisi: Add platform prefix to function name
thermal/drivers/hisi: Put platform code together
thermal/drivers/qcom-spmi: Use devm_iio_channel_get
thermal/drivers/generic-iio-adc: Switch tz request to devm version
thermal/drivers/step_wise: Fix temperature regulation misbehavior
thermal/drivers/hisi: Use round up step value
thermal/drivers/hisi: Move the clk setup in the corresponding functions
thermal/drivers/hisi: Remove mutex_lock in the code
thermal/drivers/hisi: Remove thermal data back pointer
thermal/drivers/hisi: Convert long to int
thermal/drivers/hisi: Rename and remove unused field
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull cramfs updates from Al Viro:
"Nicolas Pitre's cramfs work"
* 'work.cramfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cramfs: rehabilitate it
cramfs: add mmap support
cramfs: implement uncompressed and arbitrary data block positioning
cramfs: direct memory access support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted stuff, really no common topic here"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: grab the lock instead of blocking in __fd_install during resizing
vfs: stop clearing close on exec when closing a fd
include/linux/fs.h: fix comment about struct address_space
fs: make fiemap work from compat_ioctl
coda: fix 'kernel memory exposure attempt' in fsync
pstore: remove unneeded unlikely()
vfs: remove unneeded unlikely()
stubs for mount_bdev() and kill_block_super() in !CONFIG_BLOCK case
make vfs_ustat() static
do_handle_open() should be static
elf_fdpic: fix unused variable warning
fold destroy_super() into __put_super()
new helper: destroy_unused_super()
fix address space warnings in ipc/
acct.h: get rid of detritus
|
|
Pull more block layer updates from Jens Axboe:
"A followup pull request, with some parts that either needed a bit more
testing before going in, merge sync, or just later arriving fixes.
This contains:
- Timer related updates from Kees. These were purposefully delayed
since I didn't want to pull in a later v4.14-rc tag to my block
tree.
- ide-cd prep sense buffer fix from Bart. Also delayed, as not to
clash with the late fix we put into 4.14-rc.
- Small BFQ updates series from Luca and Paolo.
- Single nvmet fix from James, fixing a non-functional case there.
- Bio fast clone fix from Michael, which made bcache return the wrong
data for some cases.
- Legacy IO path regression hang fix from Ming"
* 'for-linus' of git://git.kernel.dk/linux-block:
bio: ensure __bio_clone_fast copies bi_partno
nvmet_fc: fix better length checking
block: wake up all tasks blocked in get_request()
block, bfq: move debug blkio stats behind CONFIG_DEBUG_BLK_CGROUP
block, bfq: update blkio stats outside the scheduler lock
block, bfq: add missing invocations of bfqg_stats_update_io_add/remove
doc, block, bfq: update max IOPS sustainable with BFQ
ide: Make ide_cdrom_prep_fs() initialize the sense buffer pointer
md: Convert timers to use timer_setup()
block: swim3: Convert timers to use timer_setup()
block/aoe: Convert timers to use timer_setup()
amifloppy: Convert timers to use timer_setup()
block/floppy: Convert callback to pass timer_list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
GICv4 Support for KVM/ARM for v4.15
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
|
